We have a Linksys WRTU54G-TM that serves both as a hotspot and phone line (T-Mobile). But since it's a G, the radius doesn't cover the whole house. So instead of buying an antenna, we bought another router (Cisco Factory Refurbished Linksys E1200 Advanced Wireless-N).
So the question is: How do we connect both routers to one modem properly, the N-Wireless to be used when necessary?
how to Cascade two routers on one subnet, but when I disable DHCP on the slave router, I cannot add in any DNS settings.
View 4 Replies View RelatedI am replacing old D-Link DI-714P+ router with E1200.The old configuration was a printer connecting to D-Link router, and allow for wireless printing. Therefore, may I know how do I configure E1200 so that I still can print wirelessly, while connected to E1200 network.Assuming the printer still connected to Dlink router, can we print to E1200 then bridge to Dlink ?
View 2 Replies View RelatedMy parents are using a speedtouch 546 modem for their wired internet connection, but they would like wireles in their home. I therefore bought them a linksys e1200, and tried to get their wireless internet working.
I connected the e1200 to the speedtouch via kabel, used the cisco software to install the wifi network, and so far so good. The laptop has no problem connecting to the e1200, but no internet connection, whatever I do.
There seems to be a signal comming into the back of the e1200, since the led on both the speedtouch and the e1200 are responding, indicating that the two are sharing some information.
Looking for information on the net, I came onto 3 possible solutions.
One is cloning the MAC adress of the to the speedtouch connected wired computer to the e1200. The second has something to do with interfering IP adress ranges. The third was uninstalling the cisco software, reconnecting and resetting the modem. Let windows find the hardware and just install the e1200 drivers.
How do i make my laptop wireless without having to have my laptop connect to all the wires?
View 9 Replies View RelatedI have AT&T DSL service and a WRTU54G-TM for my wireless router and T-Mobile at Home phone service. The router is in the basement and upstairs near the back of the house Internet connectivity is weak. I have a second router, identical to the first, that I am hoping can be connected to the first, perhaps as a bridge(?).
View 3 Replies View RelatedI have a Verizon supplied actiontec g band router, and would like to place a WRTU54G-TM on the other side of the house to act as a repeater or a wireless bridge (?). I want stronger wireless at that other side of the house and beyond, and use cat5 to hook up some other devices.Can I bridge the actiontec and WRTU54G-TM together, or do they have to be the same brands?
View 1 Replies View RelatedThe last couple of weeks the phone line has been dropping until I unplug for about 30 seconds to reset. It is happening more frequently. The phone service through TMobile gets a dial tone and rings several times then drops when making a call.
View 9 Replies View RelatedA client is using Tmobile VOIP using the aforementioned WRTU54G-TM 2-line VOIP wireless router with 4-port hub. What they would like to do is to place this in their network and NOT have it change (route) the network addresses being assigned to devices 'behind' this router so even their wireless devices are all "on the same network" as the wired devices BEFORE this unit, In essence, preserve the same 'network and subnet mask' that is being issued by their DSL router via it's integrated DHCP server. ... Rather like operating this unit like an 'access point' instead of a router.Under most circumstances, I might try to assign this router a static IP outside the scope of the DHCP range the DSL router would supply, then plug the (gigabit) Ethernet network cable into one of the 4 Ethernet ports on the rear of this router - but apparently this does not 'facilitate' a connection to Tmobile's VOIP service.When attempting to do this, the connected telephone devices do not get a phone line connection and the status light(s) that normally indicate proper operation do not illuminate.
View 3 Replies View RelatedIs WRTU54G-TM affected by Wi-Fi Protected Setup security vulnerability? Device is not mentioned on this list: url..If yes, can it be fixed or is device bricked?
View 1 Replies View RelatedI recently purchased a Linksys E1200 router. I have two desktops (Windows XP) hardwired into the router, one of which is not connecting at all.I have talked to Linksys tech support 3 times already and they have not been able to fix the problem. Pinging a website got a request timeout.Pinging the router got a good response.It was properly assigned an IP address, but did not connect through the router.Under Network Connections, it displays as "Connected" but is still not able to access the Internet.
View 2 Replies View RelatedMy friend was able to access my internet connection via my guest account WITHOUT having to enter the guest password. He was able to connect using a samsung galaxy phone with the android OS. However, when I connected to my guest account using my blackberry, I WAS asked for the guest account password.
View 3 Replies View RelatedConnecting two wrg614 routers together. Have cable one as my provider. Both are wireless routers, however I want the second router to have only 3 pc hardwired in, no wireless.
View 1 Replies View RelatedI have two wireless modem/routers - a Ugo Mach5 CN458 and a Swift 4G - in two branches of my company that are distance apart and i want to connect them together so that they can be on the same network and workers in both branches can communicate and share files.
View 2 Replies View RelatedI am on the Verizon wireless router connected to my laptop and the xbox wired to laptop. I have another wireless router that i want to connect because the main router is in the basement I am on the second floor. How do I connect the xbox to the 2nd router wired?
View 1 Replies View Relatedi have two linksys wireless router on different networks that i want to connect. how do i go about it?
View 1 Replies View RelatedI am trying to set up two routers so that I can offer free wireless connectivity via three AP's in three adjoining rooms on a first floor and secured wireless and wired network connectivity in upstairs offices. The setup is like this:
Verizon DSL connectivity..static IP
The gateway modem/router is a Verizon DLink DSL 2750B with three ports connecting to three wired Access Points in three first floor adjoining rooms, and the 4th port connecting to a Cisco E1200 (wireless and ethernet router) located next to the Verizon Dlink. I would like the Verizon DLink to give open wireless connectivity via the access points and also connect to the adjacent E1200 router.
I would like the Cisco E1200 to offer secured wireless and ethernet connectivity to the upstairs offices. (connecterd to the Cisco E1200 is a 24 port Netgear switch.)I have spent considerable time talking with Verizon and Cisco/Linksys but have not been successful in just how to set this up.A former tech actually did have this setup but for what ever reason the settings were reset to factory defaults with no written record as to the necessary settings.
Basically my sister, who lives in a flat attached to the side of my parents' house, wanted me to find a solution for her to get internet, as there is no signal from my parents' wireless down in the flat.Originally I tried an old belkin wireless range extender I had lying around but even then the signal was extremely weak and the connection was too slow.So, I decided I would get some powerline adapters. But, of course, my sister needs wireless, so I figured I would use the powerlines to connect a second wireless router to the existing one.And so begin my real problems. The thing is, it actually worked fine at first. I set up a new wireless network, and had the ethernet from the powerline running in to the WAN port of the second router. But, every few minutes or so the connection would just die suddenly and take a while to come back (the connection was still there, but the browser just gave DNS errors etc).So I did some googling and fount a lot of people saying that I had to A) plug it into one of the LAN ports, not WAN, and B) disable DHCP on the second router.However when I do this I simply cant load anything at all. I'm thinking maybe there's some additional setup regarding static IPs or something that I need to do when I disable DHCP?
View 5 Replies View Relatedmy goal is to share my cable modem signal over my two story house using two wireless routers. The delima is that the routers don't support wireless bridging and if they did, the signal is too weak to make it worth while.
The remedy I came up with... buy a pair of powerline network adapters and connect one router to the other so I could have a good signal upstairs and then a good signal downstairs.
Downstairs, I have the cable modem connected to the Linksys WRT54G router, which has a line out to my blu ray player, wirelessly feeds a PC downstairs and then has a cable run to the powerline adapter.
Upstairs, I have a cat5 connecting the powerline adapter (which was tested and works with laptop) to the data input port on my second wireless router, the netgear wndr3400.
I can't get the netgear upstairs to pull an IP address from the linksys router downstairs over the powerline network.
I'm using my AE1000 to connect my computer in my home office to the router downstairs. The problem I'm having is my neighbor's routers show up on my network connections and it ends up slowing down my internet. Is there any way I can keep my adapter from trying to connect to my neighbors?
View 2 Replies View Relatedin our small office, we are using Cisco SRP527W (Router/ADSL Modem all in one ) and D-Link DGS-1210-16 (ports) as our main network devices, our 3 desktops (Windows XP), Avaya phone system and one Brother MFC 6490CW are wired connected to our D-Link switch, port1 of the switch is connected to lan port 1 of our Cisco router, we also have 3 wireless devices connected to the cisco router throught wireless signal (one Broher MFC J6910DW printer, one laptop with Win7, one all-in-one desktop with Win8), as we know, both Switch and Router support Vlan feature, but at the present, I just use default Vlan (Vlan 1) for all our data traffic, I created a DHCP Pool in Cisco router to provide IP address to all our devices (DHCP Pool: 192.168.30.101 - 192.168.30.250, Default gateway is 192.168.30.254), All wired or wireless devices can get right IP address,and all of them are able to get on to the internet, the problem is wireless and wired devices can not talk to each other, for example, my laptop is using wireless connection, when I try to ping a desktop which is wired connected to switch, there is no response, however, if I cable connect my laptop to switch, I am able to talk to the desktop and use its shared resource.
View 2 Replies View RelatedI am trying to connect a Netgear wirless router to my cable modem. I have followed the instructions on the set up wizard but it fails to get a connection with the IP and DNS info I provide.I got the IP address info by connecting intially direct from the modem to the PC and then went to Run CMD and type ipconfig /all. I then started the set up wizard and followed the instructions, turning things on in specific order etc. After input the IP and DNS info it reports an error and tells me to check the address information is correct.My internet is a static IP connection (so it tells me and the IP information doesn't change).
View 3 Replies View RelatedI have two BELKIN f5d7230-4 wireless router my goal is to connect the two wirelessly and share the internet connection.
View 2 Replies View RelatedI have linksys router connected to my cable modem. I want to change it Belkin AC900. How can I keep the linksys connected until I have tested set up for Belkin AC900 router.
View 2 Replies View RelatedI have what should be simple. Home network on cable. WRT320N is main router cabled to desktop with GB card. It is hard-wired to a Netgear WNR3500L (also gigabit). That router is hard-wired to a desktop with GB card. For testing I connected a second machine hard-wired to the WRT320N with a 10/100 card. All machines recognized cards properly at correct speed. I ran LAN Speed Test between machines. Speeds were comparable between machines regardless of cards. GB -> GB was mid-30's write, mid-80's read with GB -> 10/100 a couple of ticks slower but not significantly. The LED's on both routers will show different color if GB connection and both showed GB for the desktop connection but not the interconnect between the routers. The routers are connected at about 100' with CAT5E and straight-through.
View 5 Replies View RelatedI can't seem to get my Canon MG5220 Wireless Printer to connect to my Belkin N150 wireless router. The printer sees the belkin wireless router network name but cannot connect to it( after entering the correct security key). It worked fine with a previous wireless router. My desktop PC is connected to the belkin router via direct ethernet, and I want to be able to access my wireless printer which is located in another room from my PC. I think I remember reading that the canon mg5220 may not support WPA2 security, but Its only a year old and would prefer not to regonfigure my router's security setting. how I can get this printer to connect to my router? Any other ways to access this printer from my PC which is connected to LAN via ethernet?
View 1 Replies View RelatedIs it possible to integrate a wireless voip cisco 7921g (sccp protocol) with an small business modem router Srp527w (sip protocol), even if if is by connecting another device (like an access point) between both? I know skiny is cisco property and sip is an open source protocol, so I do not understand why cisco does not implement the skinny protocol in his Srp527w.
View 5 Replies View RelatedI tried to bridge two wireless routers wirelessly, but after extensive research I came to the conclusion that this wasn't possible.
Now I am trying to connect these two routers through a cat5 cross-over cable and I wanted to know whether can I disable DHCP on the router which has internet, and enable the DHCP of the router which is connected to the printers, because I have a few systems that shouldn't be connected to the internet.
What I had in mind is if I switch the DHCP OFF on the internet router and turn it ON on the Huawei B683 router, I could add those devices' MAC addresses to the internet gateway router to deny them access to the internet..?
I have two matching N300 Belkin routers. The cable modem feeds into modem1 and modem1 feeds into modem2. I get a good wireless connection on modem1. Modem2 shows up on a wireless scan and it accepts the password. It however will not connect.
View 1 Replies View RelatedI have two AC1200 routers? how do i connect one ac1200 to another ac1200. Only one should act as a DHCP server and broadcast wireless; the other should be simply just a hub (vs. me having to buy a separate hub). What are the correct settings and connections?
View 1 Replies View RelatedI am trying to connect a Seagate Backup Plus 4TB USB HDD to the USB port on my Belkin ShareMax N300 wireless router. The router does not recognize this HDD. I know that the HDD is functioning because it works when I connect it directly to my laptop USB. I also know the Belkin USB port is working because it recognizes a 4GB USB memory stick and a 320GB Toshiba USB HDD. Is there a fundamental compatability problem, or is there some configuration that must be performed (e.g., reformat from NTFS to FAT32, etc.)? I saw some message traffic on the Belkin support site that indicated some issues with earlier versions of Belkin routers using larger HDDs (e.g., 4 TB). My router has a serial number 121026G3101468, model number F7D7301 v1.
View 3 Replies View Relatedi have issue for Remote App to connect to the Apple TV using the Wireless network setup in my 180W.My wired Mac is able to connect to wireless connected Apple TV but my i phone (4, 4S and i Pad) are not able to connect to apple TV.
Do I have to enable some setting for this to work. It used to work in my very old Buffalo router with tomato firmware.
If I connect the Apple TV to wired network it works fine. Instantly it shows up in i Phone Remote app, but not if its on wireless network.
I am having trouble connecting the Amped Wireless AP600EX access point to my WRSV4400n. As soon as I plug the range extender into the router, instead of it receiving an IP address, it crashes the router. I have updated the router firmware to 2.021. I have checked the box in the WDS menu to "allow wireles signal to be repeated". I will check with Amped, but are there any known issues between this router and the Amped Wireless family of range extenders?
View 1 Replies View Related