Networking :: Configuring Multiple Routers WRT54G

Sep 1, 2011

I'm trying to troubleshoot a wireless network at an Inn which is shared among three buildings. The internet at the main building works fine.

However there is a WDS set up for the other two houses that are part of the property. The network is a bit of a mess IMO. The main problem is that routers on the end of the WDS chain work for awhile after booting, but frequently stop issuing IPs. When a device tries to connect it says unable to configure IP or something like that. Rebooting the router always fixes the problem.

My networking knowledge is very limited but I think some settings must be incorrect. I will try to described the setup here..

All of the following routers are WRT54G's with DDWRT

Main router: 192.168.1.1 [different SSID that WDS], all routers forward DHCP to this router
WDS router 192.168.1.3 at main building is connected to an cantenna that shoots the signal over to 1st house. Gateway & Local DNS set to 192.168.1.1
WDS router 192.168.1.4 at that house is the main AP for that house and gets its signal from 1.3's cantenna. Gateway & Local DNS set to 192.168.1.3
WDS router 192.168.1.5 under the deck at the 1st house picks up that signal from 1.4 and uses a cantenna to send it to the 2nd house. Gateway & Local DNS set to 192.168.1.4
WDS router 192.167.1.6 under the deck of the 2nd house gets the signal from 1.5's cantenna. Gateway & Local DNS set to 192.168.1.5

The IP configuration problems happen at the 2nd house with 192.168.1.6. I believe 1.5 also has IP configuration problems but that router is not used other than to transmit to 1.6. Again rebooting the router fixes the issues temporarily. It works for a couple days up to a couple weeks before the IP problems start.

Mac addresses for the WDS are set of course. I have been trying to experiment with settings for awhile, but do not really know what I am doing. I am not the one who set this up.

Also under the Advanced Routing tab,here are the Static Routing settings:
192.168.1.3: Destination LAN NET: 192.168.1.0, Gateway: 192.168.1.1
192.168.1.4: Destination LAN NET: 192.168.1.3, Gateway: 192.168.1.1
192.168.1.5: Destination LAN NET: 192.168.1.4, Gateway: 192.168.1.3
192.168.1.6: Destination LAN NET: 192.168.1.5, Gateway: 192.168.1.4

Update: looks like STP should be enabled for WDS? Going to try enabling that I guess.

View 1 Replies


ADVERTISEMENT

Configuring Multiple Routers In Wifi Connection

Oct 15, 2012

I want to set up a WiFi internet connection for a campus. I plan to use 4 routers. the first one is directly connected to the internet. I want to share internet access wirelessly with the other routers. Each of the routers should be a hotspot for each of the four blocks in the campus.

View 1 Replies View Related

Cisco :: Configuring AP1121G-E-K9 For Multiple SSID With Multiple VLAN?

May 28, 2013

i`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that

1) i`m not able to broadcast the both SSIDs in the same time from the Access point

2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
 
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?

View 2 Replies View Related

Networking :: Configuring Linksys WRT54GL For Secure Connection

Nov 13, 2011

I bought a Linksys WRT54GL wireless router. Right now it's running unsecured and open. How to configure it to a secure connection?

Security Type options are: Shared, WPA2-Personal, WPA-Personal, WPA2-Enterprise, WPA-Enterprise, and 802.1x

Encryption Type options are: None, and WEP

View 5 Replies View Related

Networking :: WRT54G Very Slow Performance

Feb 24, 2012

I have a shitty WRT54G right now, and its slow as heck. I was thinking of getting this:

URLS ,I know the later is a modem and a router as opposed to just a router in the first link.I have comcast, I hear it uses Docsis 3.0 right? Mine is a 2.0 modem right now.

View 17 Replies View Related

Cisco Application Networking :: CSS 115003 Configuring HTTP Compression (not Work)

Jan 18, 2012

I need configure HTTP Compression by hardware on CSS 11503. I make config like this [URL]
 
My config:
 
service s1
ip address 10.1.66.11 (web server)
keepalive type none

[Code].....

View 4 Replies View Related

D-Link DIR-601 / Multiple Connections With Wireless LAN Without Networking?

Nov 9, 2011

what I want to do is setup a Tablet for use and share my one Internet connection with it and my desktop. I do not want the desktop and the Tablet networked with each other. there is a Tablet on Newegg: Velocity Micro Cruz Reader R103. the details say it's communication is 802.11b/g Wireless LAN. so I copy and paste that on Newegg and get: D-Link DIR-601 Wireless Broadband Router. not sure if that's what i need or what the configuration would be but I kind of know how to set it up.my question is can I connect a Desktop and a Tablet or any PC device to a router like this with out networking the individual units with each other? just to where it serves as more a splitter. is there any wireless alternatives to only "split" the Internet connection and not network the desktop and Tablet?

View 3 Replies View Related

Multiple Monitors Media Pc Networking Setup?

Jul 25, 2012

So I'm building a house... in the living room there will be one server-like computer. This computer will also work with a NAS. So there will plenty of storage to place pictures and movies etc etc.Every room in the house will have a coax cable and CAT6. What I want is for fast file access to the server all computers in all rooms can use the CAT6 cable. That isn't the issue, because i will use network dives and mapping.e're planning on putting a TV in every room, so we want to perfect our media setup. But how can i make it, that the server will be able to stream different movies to different TV'S at the same time? The TV'S can get the video feed via coax? Or should I pull one more cable to all the rooms?So how can i have it that the media can be accessed at the same time? I can duplicate the monitors, but is it possible to have the server/computer play 2 or more different movies to different TV'S at once?

View 1 Replies View Related

Networking :: After Power Outage Router No Longer Working WRT54G

Feb 10, 2011

Two days ago there was a quick power outage here, just one of those flicks off flicks back on deals, but when it came back on I noticed my internet wasn't working. Couldn't figure out what the deal was so after trying a few other things I ended up eliminating my Linksys WRT54G router and just using my DSL modem. Internet works fine.

Now, I've always been kind of sketchy on networking stuff, but I don't think there router is broken I just think it's been reset or something and now I don't know what setting I need to change to get it back to working order.

Here's the kicker though. I had the DSL modem in bridge mode and the router handling traffic before but I had a huge issue with that where my Steam would only download at 10-15 KB/s. Not only that but it would take forever to login and crash constantly. This would happen on my brother's computer too, which is on the same network. I could never figure out how to fix it as forwarding ports had no effect and every other fix I could think of amounted to nothing as well. Hell, I even did a fresh install to no avail.

Now going straight into the modem my Steam is downloading at full speed and there's no slow login or crashing issues. The thing that boggles my mind though is that more than once before I tried doing this very same thing, going straight into the modem, and it didn't fix the problem.

Ideally I want to get the router back up and running and keep my Steam in full working order, essentially to have my cake and eat it too, but the priority is to get the router back up in running as I have another PC on this network, plus a 360, a PC, a wireless printer, and two Wii's.

View 10 Replies View Related

Cisco WAN :: Configuring 861 NAT With Multiple Public IPs

Jan 20, 2012

I've replaced my dead ASA5505 with a 861-K9.Our ISP provides a subnet of public address /29 (wan side)  by example: 200.200.200.xxx /29,we have 3 servers (lan side) in the example 10.1.1.xxx /24 is the same case than Johnatan, the only difference are the public addresses. [URL], everything is ok when NAT via the FE4 public address, but when do the same with other public IPs doesn't work.

View 7 Replies View Related

Cisco :: 871 - Configuring Static Nat For Multiple Web Servers

Mar 13, 2012

I am trying to configure a Cisco 871 router.There are 3 servers on my network that need static public IPs but also still need to communicate on the local network.I have given my WAN interface the first IP in the block and set up PAT for the rest of the computers on the network with that IP which is working fine. Next I set up static NAT rules for the servers translating 3 of the remaining public IPs to the internal addresses of the servers.I can access those servers internally using the public IPs but not from outside the network. A traceroute from outside the network gets dropped when it gets to my ISP.I've never configured more than one static ip for a network before and i know i've just missed a step here. Do I also need to use static routes? Will that update the next hop's routing table? Do I need to make an ACL to permit any host to the servers? If so, do I use the internal or external address? [code]

View 2 Replies View Related

Linksys Wireless Router :: Configuring WRT54G With New TP-Link 740n?

Jun 16, 2012

I have a Linksys WRT54g router that works fine, but the signal is not very good on some points of the house.So I bought a TP-Link 740n to use as a second router. My idea is to connect both routers with a 10 meters lan cable that I have, to make the signal better on points that are distant from the main router (Linksys) or separated by walls. When job is done, will I see two different networks (one for each router) on my laptop or only the "original" signal (WRT54g)?

View 5 Replies View Related

Linksys Wireless Router :: Configuring WRT54G To Block Websites?

Mar 14, 2012

how to setup WRT54G for blocking all unwanted websites for users. When tried to configure Website under Access Restrictions tba, it accepts. However it doesn't block.

View 1 Replies View Related

Home Network :: Multiple Router Networking Versus Adding A Switch?

Apr 22, 2011

on my home network I currently only run an Airlink101 AR675W router. We have a couple issues with this. The router for one is in my basement and there are points in my house that have low signal strength, especially upstairs in the far corners of the home. Second is I am currently running my home PC as a media center but it is set-up wirlessly so streaming is clunky and jittery. Also on this network is 3 X-box's wired, a PS3 running wirless, 2 PC's wired in, 2 wirless laptops and the afore mentioned wirless PC. A lot of weight for the network. What I want to do is move the router upstairs, hardwire it into my wireless PC (the one doing the streaming) and connect a second router (an identical make and model I am buying this weekend) downstairs which will be basically used as an "expansion" of the wirless and a switch for the hardwired devices downstairs. would this be better than simply moving the wirless router upstairs (hardwiring my PC) and putting a 5 or 8 port switch in downstairs for the X-box's and 2 wired PC's there?

View 2 Replies View Related

Cisco VPN :: Configuring Multiple VPN Tunnels On 1721 Router

Jan 10, 2012

I am in the process of configuring two vpn tunnels on one interface of cisco router series 1721. Any link or document with more information?

View 5 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.x - Configuring Multiple AD Domains For Authentication

Jan 7, 2013

Currently on ACS 5.2 and our MS Active Directory is migrating to a completely new domain. There will be a two way trust between them for the 24 month migration period. How best to configure ACS connect to both domains?

View 2 Replies View Related

Cisco Switching/Routing :: 3750 - Configuring Multiple VLANs For Single Port

Apr 11, 2012

I would like to configure a 3750 switch port to be able to use two vlans. I know you can do this with a voice and data vlan, but what about two data vlans ? Say I have two devices, one on a 10 subnet and the other on a 172 subnet, but i only have one wall jack for both devices to plug into. So I use a mini switch to connect both devices and connect the switch to the wall jack; and of course this all leads back to one switch port. When I go to enter the switchport access vlan 172 cmd, how would I also make it so the device on the 10 subnet could route out ?

View 9 Replies View Related

Routers / Switches :: Networking With Switch / Bridge And Routers?

Jun 13, 2011

modem
........ |
........ |
----switch-----
|................ |
|................ |
Router 1.... Router 2
|..................... |
|..................... |
Computer 1.....Computer 2

......................Computer 3 Router 1 points to a VPNRouter 2 access to the internetComputer 3 needs to access router 1 (VPN). Both Computer 2 and 3 are in a different room than computer 1, and router 1. Computer 2 is networked via cat5e to router 2.Is is possible to have Computer 2 and 3 share the cat5e, yet access different routers?

View 5 Replies View Related

Cisco AAA/Identity/Nac :: ACS5.3 - Configuring Multiple Identity Sources

Aug 28, 2012

I have an ACS 5.3 cluster, that is configured to use AD. There are a few wireless devices, and monitoring tools that do not have AD accounts. I would like to configure ACS to first check AD for the user authentication, and if that fails to roll over to the local (Internal Users) identity source where I can define these user accounts.
 
It seems that when the authentication hits the initial Identity Policy rule, it never moves onto the next one if the first fails.
 
Attached are screen shots that show how i'm configured for the test, i have a local user defined and I'm trying to log into the firewalls.
 
- Identity Definition : Screen shot of the main ACS definition for the rule i'm testing that's not working
- Identity Rule 1 : The configuration of rule 1 that if it fails i need it to move onto rule 2.
- Log Output : Screen shot for one of the failed attempts from the ACS View Log server.
 
Reason I need to configure it this way is:

- Wireless users authenticate to wireless using AD user accounts. Some hand held scanners do not support that and will need to authenticate using the MAC address.
- Authentication to Network devices for managment uses AD accounts. We have some monitoring tools that do not have AD accounts, and will need to    be able to log into Network devices to issue some commands (Examples: Cisco Prime LMS and NCS, Infoblox NetMRI).

View 4 Replies View Related

Cisco Routers :: RVS4000 - Multiple Internet Connections / Routers Sharing Printers?

Sep 11, 2011

I have 2 internet connections in my office one via Verizon Fios and another  one via the local cable company. On the fios connection I have an RV042 VPN  router and on the Cable company connection I have an rvs4000 router, I would  like to know if there is a way I can connect the 2 so I can share a printer I  have on one of the 2 networks from the other network without using the VPN  feature, like via an ethernet cable connected between the 2 and some kind of  static route maybe?

View 6 Replies View Related

Networking :: 1 DSL Modem With 2 Routers WRV210

Sep 12, 2011

I got a client who's getting a VOIP system installed into their/my network. The VOIP IT guys are demanding a separate static public IP address to be forward/made available to their router. They will put their phones on a different local subnet.

So here's what I've offered them and they refused:

1. separate PPPOE login; that way we share the modem and each router handles their own session (cleanest solution but they don't want to pay extra)
2. plug their router into DMZ of my WRV210 (they said they require publicly routed IP going direct to their device (but in this case they would have to assign my private IP as their WAN IP and all internet traffic would go to them unfiltered))

View 9 Replies View Related

Routers / Switches :: Networking Setup With DLink DL-604

Apr 8, 2011

I had this small internet cafe with 15 units pc. and browsing the web is not that stable. i have to unplug the internet modem everytime i can't connect to the internet.I think it has something to do with the settings that was in the router since it was just configured by a tech guy which i think not 100% sure of what he did, though it can connect to net for sometime but most of the time it is down.

View 5 Replies View Related

Routers / Switches :: Basic Networking Setup For More Than 40 PCs

Jul 23, 2011

How to set up more than 40 pc's with out internet connection using linksys switch.

View 3 Replies View Related

Implement Networking In Three Floor Office By Using Routers And Switches?

Apr 24, 2011

How can i implement networking in my THREE floor office by using routers and switches?

View 1 Replies View Related

Routers / Switches :: Using Multiple Routers With DSL Modem?

Oct 24, 2011

In my office we have concrete walls and very limited wiring. The way it is set up is we have a Verizon DSL Modem that comes in then I have a router with it that splits the signal to 4 other routers that each split the signal 2 to 3 more times. I have to use routers so that it assigns IP addresses.I bought a new D-Line N300 Wireless router with USB imput. I want to attach my Home Media Network Hard Drive Cloud edition to the 1st router (attached to the modem) and then share the data off that hard drive with everyone connected to the sub routers.

View 4 Replies View Related

Configuring 2 Wireless Routers To Work Together?

Oct 17, 2011

I'm trying to ensure I have wireless coverage in my entire house and having extreme difficulty getting all machines to play nicelyWireless modem router #1 (downstairs in my house) is connected to the ADSL line and has the following config:IP Address = 192.168.1.1 DHCP on DHCP pool 192.168.1.3-192.168.1.100 Subnet = 255.255.255.0 Wifi channel = 1 Wireless router #2 (upstairs) is connected by ethernet cable to Wireless modem router #1 and has the following config:IP Address = 192.168.1.2 DHCP off Subnet = 255.255.255.0 Wifi channel = 11 Different SSID and encryption key to Wireless modem router #1 With this configuration, I can connect to the internet via both routers and all seems to be well. Except... having established a connection through either one, my machines will only make a pretend connection with the other one. By "pretend", I mean that the (Windows) machine says it has an excellent connection to the router but can only see machines on the LAN - it cannot get to the internet even though other machines are connected through the same router to the internet.

For example, if I'm sitting next to the downstairs router and establish a connection with it, all is well. Then I move upstairs and my machine switches to the upstairs router. Signal strength will be reported as "Excellent" and I'll be able to connect to the local NAS or printer but no external devices or sites.I have tried having the same SSID and wireless configuration on both but the result was the same.Today I read the suggestion to enable the DHCP server on the 2nd router but to set it to distribute a different non-overlapping IP range (i.e. router 1 can have a pool of 192.168.1.3-192.168.1.50, and router 2 can have a pool of 192.168.1.51-192.168.1.99)

View 4 Replies View Related

Routers / Switches :: Home Networking / Netbook Can't Find Desktop?

Dec 7, 2011

Although we have a moderately wired house with cat6 cables runs in many of the rooms that all end in the basement, I am currently having trouble since I cat stream audio and video files from my desktop in the den to the netbook and receiver in the family room. All computers are hooked up by cable.I have tried a friends advice to plug in the exact IP address of the desktop (and vice versa on the netbook) but still the netbook cat find the desktop nor can the desktop find the netbook. I have tried home sharing in Windows 7 to no avail as I have been prompted to initiate a home network both on the netbook and the desktop when I think it is suppose to be initiated on one machine and same home network joined by the other.DSL Modem --> Linksys WRTGL router running Tomato --> switch -->various rooms (cont.)Family room (one of the various rooms) has a Buffalo WZR-HP-G300NH AirStation (with one USB port) --> 1) netbook and 2) Denon AVR receiver (with network capabilities)I have a switch in the den and the desktop and laptop computers can read off each other through folder/drive sharing even with Kaspersky Internet Security running in the background so I'm sure it's not Kaspersky meddling with my network sharing. If both are on the wireless network, the netbook can access the desktop and vice versa.Is it possible for the netbook to read off the desktop based on my current set up? I can't bring the desktop down as we use them in the den and will not have room for it in the family room. I am not inclined to purchase a stand-alone HTPC at the moment if there is a network sharing

View 2 Replies View Related

Cisco Routers :: RVS4000 Private Networking Setting Up VLANs?

Jan 23, 2013

I live in a two family residential house and we share a common fibre connection to the internet. In the basement we have a modem/router(zyxel) which is in "bridge mode".  Therefore not acting as DHCP. Behind this zyxel we have a Cisco RVS4000 router. Ports 1 and 2 go to family A, and Ports 3 and 4 go to family B. Family A and B have separate routers which are both set to "access point mode". Family A has an ASUS RT-N66U router while family B has a dlink DIR-615. The asus has an "access point mode" while the dlink needs to be set up manually to achieve this. The dlink must also have a static IP adress. The asus can receive ip adress.
 
What I have unsuccessfully tried to achieve and am currently trying to separate the networks so that both families can access internett, but at the same time it must be impossible to access VLAN1(Family A) from VLAN2(Family B) vice versa. Meaning no communication between the two families through the local network.
 
I have tried different options but I am not sure how to deal with trunk, tagged, untagged etc. etc. etc. It seems every time I manage to create two different networks there is still accessability/communication between the two VLANs and everytime I manage to give out different IP adresses to different ports i.e. 192.168.10.xx and 192.168.2.xx it is still possible to communicate. What also usually happens is that the internetconnection is severed at the same time.

View 15 Replies View Related

Cisco Routers :: SRP527W Configuring Guest Wi-Fi

Jan 28, 2012

I recently bought a Cisco SRP527W and I'm trying to setup a second wireless network for guests.

I created a "guest" VLAN and I assigned the "guest" SSID which I have created.

I created a "guest" DHCP server and assigned it to the "guest" VLAN.
 
The "guest" SSID is set to broadcast and has WPA2 Personal (TKIP+AES) authentication. These are exactly the same settings I have for the "non-guest" WiFi.
 
However, I can't get my clients to connect to the network. The "guest" WiFi is visible and clients are prompted to enter the password but after that they end up with an APIPA address. When I move the "guest" SSID to VLAN1 (along with all the other networks) then it works absolutely fine.
 
I was just wondering if I'm simply missing something in the configuration ..
 
The device is running the latest firmware (1.01.24 (003) September 7, 2011)

DHCP server has DNS Proxy setting enabled and WAN Interface configured as "Default Route" (have basically replicated the same settings as VLAN1)

View 1 Replies View Related

Cisco VPN :: Configuring 2900 SSL VPN AnyConnect On Routers

Dec 13, 2012

I want to configurate Cisco SSL AnyConnect VPN on cisco router 2900 series.when i install  this license on router after that can i configurate ssl anyconnect vpn? Must I  be first enable EULA then install this license?

View 0 Replies View Related

Cisco VPN :: Configuring DMVPN With 2 ASR1006 Routers

Jun 7, 2011

I'm trying to configure and DMVPN architecture with two routers ASR1006 to server a bank remote offices, one ASR in CO building and the other in CA building (CO: Operational Center; CA: Recovery Center).Each ASR have two LAN connections to internal network and two WAN links to remote office.  Each WAN links belongs to differents provider.Each remote office has a router with two WAN links connected to that WAN providers.We are configuring the DMVPN considering two primary tunnels in the CO building and two failover tunnels in CA building.We made the configuration (schemas and configuration attached) but we only get two tunnels up at a time.  We cannot ping from office router to four tunnels interfaces in both hubs.

We made some test disabling some tunnels and we could get communication only with two tunnels interfaces. We got communication through tunnels when we have just two.We want to have the four tunnels for high availability. We would like to know how to troubleshoot and make a design review because the examples and documentations are very limited.

View 1 Replies View Related

Cisco Routers :: Configuring VPN Connection On RV042G

Nov 4, 2012

i got a problem in configuring a VPN Connection for our Colleagues (Laptops & Iphones 4/4S/5) We got an RV042G .
 
A WAN Connection from Deutsche Telekom AG with Static IP connected in WAN1. Configured for PPPoE. Ive got configured a Port Forwarding on our SBS 2011 Server for OWA and other Services on web. I´ve got extreme Problems configuring VPN Connections. We use Quick VPN, other tools got to much buttons to click .
 
1st i configured a Group VPN , with FQDN (Remote Group) Local Group (IP only) . i configured 2 users. Then on a Laptop connected to the internet through an Hotspot Connection of an Iphone.
 
I entered the WAN IP .. Username. Password. Pressed ENTER. I get to the point of Verifyiing Network, and after it timeout with Remote Gateway not responding. Do you want to wait. If i Press Yes, after max. 1 minute there comes the message again.
 
I looked in the VPN Summary, and i see, that my username was connected through VPN for seconds, but then disconnected. Do i have overseen an option to configure??

View 4 Replies View Related

Cisco Routers :: Configuring RVS4000 VPN Option?

Dec 29, 2011

I just purchase the Cisco Router RVS4000 vpn and I am having problem configuring the VPN option.  I just try all way I could imaging, but somehow something are missing and I don't know what it is.  Here are a image of my current configuration.

No matter the change on my configuration, the status always in down.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved