I want to set up a WiFi internet connection for a campus. I plan to use 4 routers. the first one is directly connected to the internet. I want to share internet access wirelessly with the other routers. Each of the routers should be a hotspot for each of the four blocks in the campus.
View 1 RepliesI'm trying to troubleshoot a wireless network at an Inn which is shared among three buildings. The internet at the main building works fine.
However there is a WDS set up for the other two houses that are part of the property. The network is a bit of a mess IMO. The main problem is that routers on the end of the WDS chain work for awhile after booting, but frequently stop issuing IPs. When a device tries to connect it says unable to configure IP or something like that. Rebooting the router always fixes the problem.
My networking knowledge is very limited but I think some settings must be incorrect. I will try to described the setup here..
All of the following routers are WRT54G's with DDWRT
Main router: 192.168.1.1 [different SSID that WDS], all routers forward DHCP to this router
WDS router 192.168.1.3 at main building is connected to an cantenna that shoots the signal over to 1st house. Gateway & Local DNS set to 192.168.1.1
WDS router 192.168.1.4 at that house is the main AP for that house and gets its signal from 1.3's cantenna. Gateway & Local DNS set to 192.168.1.3
WDS router 192.168.1.5 under the deck at the 1st house picks up that signal from 1.4 and uses a cantenna to send it to the 2nd house. Gateway & Local DNS set to 192.168.1.4
WDS router 192.167.1.6 under the deck of the 2nd house gets the signal from 1.5's cantenna. Gateway & Local DNS set to 192.168.1.5
The IP configuration problems happen at the 2nd house with 192.168.1.6. I believe 1.5 also has IP configuration problems but that router is not used other than to transmit to 1.6. Again rebooting the router fixes the issues temporarily. It works for a couple days up to a couple weeks before the IP problems start.
Mac addresses for the WDS are set of course. I have been trying to experiment with settings for awhile, but do not really know what I am doing. I am not the one who set this up.
Also under the Advanced Routing tab,here are the Static Routing settings:
192.168.1.3: Destination LAN NET: 192.168.1.0, Gateway: 192.168.1.1
192.168.1.4: Destination LAN NET: 192.168.1.3, Gateway: 192.168.1.1
192.168.1.5: Destination LAN NET: 192.168.1.4, Gateway: 192.168.1.3
192.168.1.6: Destination LAN NET: 192.168.1.5, Gateway: 192.168.1.4
Update: looks like STP should be enabled for WDS? Going to try enabling that I guess.
i`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
i got a problem in configuring a VPN Connection for our Colleagues (Laptops & Iphones 4/4S/5) We got an RV042G .
A WAN Connection from Deutsche Telekom AG with Static IP connected in WAN1. Configured for PPPoE. Ive got configured a Port Forwarding on our SBS 2011 Server for OWA and other Services on web. I´ve got extreme Problems configuring VPN Connections. We use Quick VPN, other tools got to much buttons to click .
1st i configured a Group VPN , with FQDN (Remote Group) Local Group (IP only) . i configured 2 users. Then on a Laptop connected to the internet through an Hotspot Connection of an Iphone.
I entered the WAN IP .. Username. Password. Pressed ENTER. I get to the point of Verifyiing Network, and after it timeout with Remote Gateway not responding. Do you want to wait. If i Press Yes, after max. 1 minute there comes the message again.
I looked in the VPN Summary, and i see, that my username was connected through VPN for seconds, but then disconnected. Do i have overseen an option to configure??
They have a NETGEAR ProSafe VPN Firewall FVX538 on 192.168.1.1. They have 2 different wi-fi routers, one is static at 192.168.1.4, the other is not static.Someone donated a Linksys Wireless-B Broadband Router. They asked me to set that up. But i cannot get to the home page to change the IP address. 'multiple routers' it says to simply unplug one, so you can get to the config page at 192.168.1.1. I can not unplug the main router for the business, right? Do i need to change the IP of the Netgear temporarily? Will that bring down the network?
View 2 Replies View RelatedI've replaced my dead ASA5505 with a 861-K9.Our ISP provides a subnet of public address /29 (wan side) by example: 200.200.200.xxx /29,we have 3 servers (lan side) in the example 10.1.1.xxx /24 is the same case than Johnatan, the only difference are the public addresses. [URL], everything is ok when NAT via the FE4 public address, but when do the same with other public IPs doesn't work.
View 7 Replies View RelatedI am trying to configure a Cisco 871 router.There are 3 servers on my network that need static public IPs but also still need to communicate on the local network.I have given my WAN interface the first IP in the block and set up PAT for the rest of the computers on the network with that IP which is working fine. Next I set up static NAT rules for the servers translating 3 of the remaining public IPs to the internal addresses of the servers.I can access those servers internally using the public IPs but not from outside the network. A traceroute from outside the network gets dropped when it gets to my ISP.I've never configured more than one static ip for a network before and i know i've just missed a step here. Do I also need to use static routes? Will that update the next hop's routing table? Do I need to make an ACL to permit any host to the servers? If so, do I use the internal or external address? [code]
View 2 Replies View RelatedI am in the process of configuring two vpn tunnels on one interface of cisco router series 1721. Any link or document with more information?
View 5 Replies View RelatedCurrently on ACS 5.2 and our MS Active Directory is migrating to a completely new domain. There will be a two way trust between them for the 24 month migration period. How best to configure ACS connect to both domains?
View 2 Replies View RelatedI would like to configure a 3750 switch port to be able to use two vlans. I know you can do this with a voice and data vlan, but what about two data vlans ? Say I have two devices, one on a 10 subnet and the other on a 172 subnet, but i only have one wall jack for both devices to plug into. So I use a mini switch to connect both devices and connect the switch to the wall jack; and of course this all leads back to one switch port. When I go to enter the switchport access vlan 172 cmd, how would I also make it so the device on the 10 subnet could route out ?
View 9 Replies View Relatedsiemens se568 router installed. Net is fine in PC.but not getting the wifi connection in i fone,despite wifi icon
View 2 Replies View RelatedI have two wifi routers which I have connected together with an ethernet cable to extend coverage across my house. The ethernet cable is connected to a LAN port on the first router and the internet port of the second router. This works fine and creates a second network that I can connect to the net on. The problem iseemingly randomly, about every 15 minutes, the second router will lose internet connection. My laptops and phone still stay connected to it, but windows lists it as having no internet connection. If I then wait a couple of minutes and reconnect, internet will be working again.
View 4 Replies View RelatedMy N150 wireless router sees 25mb+ speed from my internet connection but my wireless connects at 1mb. Why is the WiFi being resricted?
View 2 Replies View Related* ADSL modem connected to internet
* WiFi router (Netgear WPN824v2) connected to ADSL modem
* CPU, iPhone and iPad connected to router, CPU wired connection.Everything has worked like a charm up until a couple of days ago. Now the link between the router WAN port and the modem randomly drops. Stays dropped for 1-3 secs and then connect again. When its really bad this happens with 5-10 secs intervall. This made it impossible to use the network from any of the devices.If I disconnect the CPU from the router and connect it direcly to the modem and change the IP settings to match the modem network the CPU connects without errors to the internet, iPad and iPhone connected to the router keeps having problems.Restarting the router does not change anything and it seems to be more frequent errors during heavy load hours, in the morning I have almost no problems at all, in the evenings I cant almost use the wireless devices (CPU works fine as its now connected directly to the modem not through the router).I havent changed a setting in the last year, it just came right out of the blue.I have hard reset both the modem and the router and reconfigured them (that I dont want to do again as I have some virtual servers, port forwards, port triggers and so on :P).As it came right out of the blue without me changing anything on any device and as it seems to be more frequent during heavy load hours I'm suspecting that the ISP is involved, but how can they be (it works fine with devices connected straight to the modem)?
When i try to enter the password for my N300 Belkin Router into my wifi connection setup in my computer it will not accept any letters, only numbers.
View 1 Replies View RelatedI am trying to set up two routers so that I can offer free wireless connectivity via three AP's in three adjoining rooms on a first floor and secured wireless and wired network connectivity in upstairs offices. The setup is like this:
Verizon DSL connectivity..static IP
The gateway modem/router is a Verizon DLink DSL 2750B with three ports connecting to three wired Access Points in three first floor adjoining rooms, and the 4th port connecting to a Cisco E1200 (wireless and ethernet router) located next to the Verizon Dlink. I would like the Verizon DLink to give open wireless connectivity via the access points and also connect to the adjacent E1200 router.
I would like the Cisco E1200 to offer secured wireless and ethernet connectivity to the upstairs offices. (connecterd to the Cisco E1200 is a 24 port Netgear switch.)I have spent considerable time talking with Verizon and Cisco/Linksys but have not been successful in just how to set this up.A former tech actually did have this setup but for what ever reason the settings were reset to factory defaults with no written record as to the necessary settings.
I have an ACS 5.3 cluster, that is configured to use AD. There are a few wireless devices, and monitoring tools that do not have AD accounts. I would like to configure ACS to first check AD for the user authentication, and if that fails to roll over to the local (Internal Users) identity source where I can define these user accounts.
It seems that when the authentication hits the initial Identity Policy rule, it never moves onto the next one if the first fails.
Attached are screen shots that show how i'm configured for the test, i have a local user defined and I'm trying to log into the firewalls.
- Identity Definition : Screen shot of the main ACS definition for the rule i'm testing that's not working
- Identity Rule 1 : The configuration of rule 1 that if it fails i need it to move onto rule 2.
- Log Output : Screen shot for one of the failed attempts from the ACS View Log server.
Reason I need to configure it this way is:
- Wireless users authenticate to wireless using AD user accounts. Some hand held scanners do not support that and will need to authenticate using the MAC address.
- Authentication to Network devices for managment uses AD accounts. We have some monitoring tools that do not have AD accounts, and will need to be able to log into Network devices to issue some commands (Examples: Cisco Prime LMS and NCS, Infoblox NetMRI).
configure my D-link wifi Modem DSL-2750U for Reliance Broadband.I dont understand codes but a simple explanation and step by step
View 3 Replies View RelatedI have 2 internet connections in my office one via Verizon Fios and another one via the local cable company. On the fios connection I have an RV042 VPN router and on the Cable company connection I have an rvs4000 router, I would like to know if there is a way I can connect the 2 so I can share a printer I have on one of the 2 networks from the other network without using the VPN feature, like via an ethernet cable connected between the 2 and some kind of static route maybe?
View 6 Replies View RelatedIn my office we have concrete walls and very limited wiring. The way it is set up is we have a Verizon DSL Modem that comes in then I have a router with it that splits the signal to 4 other routers that each split the signal 2 to 3 more times. I have to use routers so that it assigns IP addresses.I bought a new D-Line N300 Wireless router with USB imput. I want to attach my Home Media Network Hard Drive Cloud edition to the 1st router (attached to the modem) and then share the data off that hard drive with everyone connected to the sub routers.
View 4 Replies View RelatedI'm trying to ensure I have wireless coverage in my entire house and having extreme difficulty getting all machines to play nicelyWireless modem router #1 (downstairs in my house) is connected to the ADSL line and has the following config:IP Address = 192.168.1.1 DHCP on DHCP pool 192.168.1.3-192.168.1.100 Subnet = 255.255.255.0 Wifi channel = 1 Wireless router #2 (upstairs) is connected by ethernet cable to Wireless modem router #1 and has the following config:IP Address = 192.168.1.2 DHCP off Subnet = 255.255.255.0 Wifi channel = 11 Different SSID and encryption key to Wireless modem router #1 With this configuration, I can connect to the internet via both routers and all seems to be well. Except... having established a connection through either one, my machines will only make a pretend connection with the other one. By "pretend", I mean that the (Windows) machine says it has an excellent connection to the router but can only see machines on the LAN - it cannot get to the internet even though other machines are connected through the same router to the internet.
For example, if I'm sitting next to the downstairs router and establish a connection with it, all is well. Then I move upstairs and my machine switches to the upstairs router. Signal strength will be reported as "Excellent" and I'll be able to connect to the local NAS or printer but no external devices or sites.I have tried having the same SSID and wireless configuration on both but the result was the same.Today I read the suggestion to enable the DHCP server on the 2nd router but to set it to distribute a different non-overlapping IP range (i.e. router 1 can have a pool of 192.168.1.3-192.168.1.50, and router 2 can have a pool of 192.168.1.51-192.168.1.99)
We have 2 Dell laptops and 1 Mac book all connected via a wireless router. Everything worked just fine until we got a Mac desktop which we connected via Ethernet cord for my husband's work. Now the wireless connection to our laptops disconnects at least 3-4 times per day and we need to unplug everything from the router and plug back in to get it to work again. The Ethernet connection to the desktop doesn't seem to have any issues.
View 7 Replies View RelatedWhen I connect 2 laptops to my router, why does the speed/connection get split? I would understand that if the speed was maxed out or something but it's a lame 500 kb/s connection. Do all wify routers behave this way? It's kind of annoying since there's a trafic quota limit implemented and when someone downloads, the other one can't do s^&t? how to handle this?
View 8 Replies View RelatedI recently bought a Cisco SRP527W and I'm trying to setup a second wireless network for guests.
I created a "guest" VLAN and I assigned the "guest" SSID which I have created.
I created a "guest" DHCP server and assigned it to the "guest" VLAN.
The "guest" SSID is set to broadcast and has WPA2 Personal (TKIP+AES) authentication. These are exactly the same settings I have for the "non-guest" WiFi.
However, I can't get my clients to connect to the network. The "guest" WiFi is visible and clients are prompted to enter the password but after that they end up with an APIPA address. When I move the "guest" SSID to VLAN1 (along with all the other networks) then it works absolutely fine.
I was just wondering if I'm simply missing something in the configuration ..
The device is running the latest firmware (1.01.24 (003) September 7, 2011)
DHCP server has DNS Proxy setting enabled and WAN Interface configured as "Default Route" (have basically replicated the same settings as VLAN1)
I want to configurate Cisco SSL AnyConnect VPN on cisco router 2900 series.when i install this license on router after that can i configurate ssl anyconnect vpn? Must I be first enable EULA then install this license?
View 0 Replies View Related I'm trying to configure and DMVPN architecture with two routers ASR1006 to server a bank remote offices, one ASR in CO building and the other in CA building (CO: Operational Center; CA: Recovery Center).Each ASR have two LAN connections to internal network and two WAN links to remote office. Each WAN links belongs to differents provider.Each remote office has a router with two WAN links connected to that WAN providers.We are configuring the DMVPN considering two primary tunnels in the CO building and two failover tunnels in CA building.We made the configuration (schemas and configuration attached) but we only get two tunnels up at a time. We cannot ping from office router to four tunnels interfaces in both hubs.
We made some test disabling some tunnels and we could get communication only with two tunnels interfaces. We got communication through tunnels when we have just two.We want to have the four tunnels for high availability. We would like to know how to troubleshoot and make a design review because the examples and documentations are very limited.
I just purchase the Cisco Router RVS4000 vpn and I am having problem configuring the VPN option. I just try all way I could imaging, but somehow something are missing and I don't know what it is. Here are a image of my current configuration.
No matter the change on my configuration, the status always in down.
I know that you shouldn't update router firmware from a wireless connection. The other day, somebody told me that you shouldn't configure a router(such as changing passwords, channels, etc) from a wireless connection. I change my router settings from a wireless connection all the time.
View 1 Replies View RelatedMy neighbor and I were wondering if it is possible to combine our respective internet connections in order to gain a faster connection overall. What would be ideal would to have a wireless router in one of our houses, that is simultaneously connected to both of our ADSL routers, and to which both of us are able to connect. Do I need a specific type of router?
View 5 Replies View RelatedIf you have two wireless routers on the same private network. On configuring the second router's password and SSID I know the second wireless routers DHCP must be turned off.Can you explain step by step on configuring the second wireless. Must the second wireless be connected to the internet. If yes, how? Must I take the first wireless router off the modem and connect it to the second wireless router for internet connection. (Problem with that is connection from the ISP)
View 2 Replies View RelatedI'm having trouble getting my RV220W router to work with a DSL modem. I pre-configured the device and shipped it to one of our store locations. I came to find out that the site had an "Advanced" modem (according to the carrier) and I had to have them "bridge" the modem. Prior to having the modem "bridged" I was able to have the user plug the RV220W into the modem, and the computer that was hard-wired to the router was pulling the correct set of IP addresses, however, my VPN tunnel was not working because the WAN address that the RV220W was receiving was 192.168.2.12 instead of the staticly assigned IP address from the ISP After bridging the modem, the user is able to access the RV220W but he does not have internet connectivity. According to the carrier, this is because we need to enter their PPOE username and password into the RV220W. My only problem is that my on-site person is not very technical, and although I have access to one of our other sites with a working RV220W I'm not able to find where I enter this PPPOE information into the device. get this thing setup so that the customer is able to get connected to the internet, and that my RV220W is pulling the correct staticly assigned IP address from the ISP?
View 5 Replies View Relatedgetting a SF300 to properly route IP between 2 VLANs. I've watched the demo video and performed everything it showed, but I get the most bizarre half-way results. I haven't done anything on Cisco routers in about 15 years, so I'm a little rusty.
We have an office LAN with a cable modem/router for Internet access where the modem/router has IP address 192.168.1.1. We have the usual 24 bit prefix net mask. The SF 300 is connected to this network on port 1.
I have configured port 1 to VLAN 1, interface in Access mode, assigned a static IP address of 192.168.1.36, which is a free address on our office LAN. I have configured port 2 to VLAN 2, interface in Access mode, assigned a static IP address of 192.168.3.1 I put a static route in the modem/router, pointing 192.168.3.0/24 to 192.168.1.36.
I have a PC on 192.168.3.10 attached to port 2.
The SF300 can ping 192.168.3.1, but not 192.168.3.10. 192.168.3.10 can ping 192.168.3.1. It can also ping 192.168.1.1, and can pull up an HTTP router admin page from 192.168.1.1. 192.168.3.1 can be pinged from anywhere on 192.168.1.x, but 192.168.3.10 cannot be pinged from 192.168.1.x. Finally, 192.168.3.10 cannot ping any other addresses on 192.168.1.x except 192.168.1.1, and cannot reach the Internet.
Here's my configuration:
switch6d919d#show runconfig-file-headerswitch6d919dv1.3.0.59 / R750_NIK_1_3_647_260CLI v1.0set system mode router
file SSD indicator encrypted@ssd-control-startssd configssd file passphrase control
[Code].....
I have an issue with configuring the VPN Stateful failover between two cisco routers 3845. The stateful HA is not up.
Below is the topology
Configuration on HA-1
interface GigabitEthernet0/0
ip address 194.170.9.183 255.255.255.240
ip accounting output-packets
duplex auto
speed auto
[code]....