My neighbor and I were wondering if it is possible to combine our respective internet connections in order to gain a faster connection overall. What would be ideal would to have a wireless router in one of our houses, that is simultaneously connected to both of our ADSL routers, and to which both of us are able to connect. Do I need a specific type of router?
View 5 RepliesI am currently working on a project that needs to install a router (or just a network device) that can offer 2 or more DHCP networks. We have been searching a network device for this but haven't gotten any good news yet. Any model or device that can fulfill this requirement?
View 6 Replies View RelatedHow do you setup multiple networks on one router? Is it as easy as changing subnets?
View 8 Replies View Relatedi have a acer laptop running windows 7 ultimate. I am unable to connect to public WiFi hotspots. But i m able to connetc to ad hocs and my mobile WiFi hotspot
View 2 Replies View RelatedI have tried restarting my laptop multiple times (something that usually works for me in terms of reconnecting to the internet) but that didn't work. And like i said it does not recognize a single wi-fi network while my ipod, phone, and the other computers in my household recognize our wi-fi and our usual neighbors wi-fi without any problem.I was torrentingsome music yesterday, and may or may not have stumbled across a bad site with a virus, but that's the only conclusion I could make.(Currently posting this on my brother's computer)I need to get my connection back and get online again asap?
View 8 Replies View RelatedI work in a small village in Africa and Interent access is often very unreliableTherefore I have 3 different ways of accessing the Interent from my home.The cheapest is Wifi from a local provider, but that doesn't always work. More expensive and still often unreliable is a 3G access. Then, when WiFi and 3G don't work I still can access the Internet via a Inmarsat BGAN satellite terminal, but that is very expensive.What I'd like do is to connect several computers to the same WiFi, 3G, BGAN Satellite Interent (all Ethernet) access via a home WiFi network.Now the questions I have:- can I just connect everything to a switch and then to the Wan-port of a wireless router?- how do the prioritisation works? When there is 3G available, I dont want to access the Internet via the BGAN, bacause that's too expensive?
View 2 Replies View RelatedI have a toshiba 2010 windows 7 laptop, and like two days ago it wouldnt connect to my wifi. i keep going to network and sharing but my network wont come up everyone elses does though. ive tried to fix problem but it just keeps saying connect to a network..or plug in ethernet.
View 1 Replies View RelatedI manage a network using Windows Server 2008 r2 that connects to the Internet (ISP) through a wireless radio antenna. We have three other locations that also connect to the same ISP through wireless radio antennas on the roof of each building. Those locations are windows XP machines. Each location is separated by more than 1,000 ft and do not have line of sight to each other. I'm wanting the XP machines to be able to logon to the domain of the server and access shared files
View 1 Replies View Relateddo airport cards built in to ibook g4 laptops connect to linksys wifi networks?
View 2 Replies View RelatedD-Link, RangeBooster N, Dual Band Router.
I would like to set one network for surfing and another for gaming.
I want to setup two WIFI network with one Router at home.
View 2 Replies View RelatedI am having trouble setting up two networks.Basically, i want one 'private' network and one public network. The problem is, the private network can't access the internet.(Network 2)
Network 1(Public) works fine as i don't want them to access Network 2.Here's how it is setup.
Internet
|
Router/Modem (Network 1)
|
Server NIC1
Server NIC2
|
Switch - (Network 2)
Network 1 can access the internet and shared files on the server.
Network 2 can access Shared files on the server (which is what i want) but cannot access the internet.
Router/modem IP is 10.10.1.254 subnet 255.255.255.0
Server NIC 1 IP is 10.10.1.252 subnet 255.255.255.0
Server NIC 2 IP is 10.10.1.251 subnet 255.255.255.0
How can i get computers in Network 2 to access internet?
Explain the risks of not using multiple networks on a 300 host LAN
View 1 Replies View RelatedI have 3 Macs (OS 10.6.8) and one PC (Windows 7) at work. They are all connected to the company network for internet and access to shared network drives.The computers are used for media (mostly video) production and we need to move large files between the computers easily and quickly. The current network (company wide) is slow and unreliable, so I would like to create a separate network for these four computers and have them connected to both the company network and the office room network. Each computer already has two network ports and I have a router I can use.
View 3 Replies View RelatedWe have 36 cctv cameras slowing down our oracle network pc's all in same subnet. I want to remove the dvr's of cctv to a separate network to improve performance. How to accomplish that with a Rv042 linksys router? Or is there any other better way around. 5 Users access the cctv cameras all the time.
View 2 Replies View RelatedI have a Windows 7 Pro Desktop with an on-board Ethernet and an Axis USB To Ethernet adapter. The on board Ethernet is configured as dhcp and obtain the address 10.162.146.123 with 255.255.255.0 subnet. The Axis USB to Ethernet adapter is static ip configuration with 10.38.25.37 and 255.0.0.0 as subnet. Under the adv settings I have also another ip 11.38.25.37 with 255.0.0.0 subnet. When the Axis is communicating 10.38.0.1 network I can not access the internet using the on board Ethernet 10.162.146.123. I have to disable either one of the cards to access one network at a time.
View 3 Replies View RelatedI currently have a hub-and-spoke VPN configuration with 6 ASA 5505's at remote sites all connected to an ASA 5510 at HQ via IPSEC lan-to-lan tunnels. My current configuration allows hosts on the remote site networks to talk to hosts on the HQ network, but not to hosts on the other remote sites.I have receieved a request to allow comminucation between the remote sites as well, with traffic all routed through the 5510 at HQ.
View 1 Replies View RelatedIm using 2 TP-Link TL-WA7510N to bridge a internet connection the connection is using a captive portal for my guests via pfsense. What i would like to do now is run a pc on the same connection without using the captive portal .So basicly i would need 1 secure network for my single pc and the one with captive portal for my guests.
View 1 Replies View RelatedAdding a second DAP-1522, They have 1 DAP-1522, they set that up useing the WAP(button on the side), This one is running in the frontroom of the house and the 2nd bridge will be running in the bedroom of the house.She has tried to click on the WAP button on both Dap-1522's and then the router to sync but thats not working, from what we can tell. I think I will need to manually config them now that a second one has been introduced.the frontroom Bridge is 192.168.0.50, but we cant find the ipaddreess for the second dap-1522 at this time. So question to all, if I can - Is there a way to identify all of the Dap-1522's on the network or anything that is connected on the network. as the DIR-655 is only showing 2 things connected?Right now I wish she would have listened too me and had her house wired for ethernet when the house was being built.
View 1 Replies View RelatedI assume that the E4200 uses VLANs for the the guest network. Is it possible to trunk the LAN interface and pass that vlan to the switch so that you can pass the vlan to an AP?Would be great to see the Guest wireless on the Cisco 1250 like I do the main SSID.
View 5 Replies View RelatedI am looking to create an office network with each person having internet access but on a private network. however everyone will need to be able to access a communal printer. would they be able to see it if they were all on a different subnet or would i need to set up vlans?
View 4 Replies View RelatedI would like to associate multiple IPv4 networks with one physical interface in the router. All those multiple networks share the same broadcast domain(VLAN 5). I am aware that it's not possible to have multiple subinterfaces in the router with the same "encapsulation dot1Q 5". Am I correct that only option here is to configure all those networks as a secondary network to router physical interface? Or are there other possibilities than secondary addresses?
View 4 Replies View RelatedI have 3 networks coming on DMZ (VPN) interface. Only one network is able to ping the DMZ interface. See below networks coming i on the DMZ.
10.132.24.0/2410.132.25.0/2410.132.26.0/24 Only the 10.132.26.0/24 netork works as it is in the same range as the DMZ interface.
allowing the other two networks to communicate. I've attched the diagram and configs for your perusal.
I am setting up a customer site. One side is RV180W and the other side is Checkpoint 500W.
RV180W side
LAN - 192.168.100.0/24
Checkpoint side
LAN - 172.26.1.0/24
VOIP - 172.26.2.0/24
Need to setup an ipsec tunnel between the site. However, from the RV180W side, I can only ping the VOIP network, but not LAN. I have heard that RV180W only can talk to one remote network via ipsec, correct? workaround this other than changing out the RV180W?
Is there any way to make networks hidden through the WiFi Smart software? I have a Cisco Linksys E4200V2. I have gone through everything to try figure out how to make my S.S.I.D. to not be broadcasted, but seems like the only way to make it hidden is to use the Origonal Firmware make it as hidden, then install the New Firmware and software. Seems like Cisco may have missed this option. I do know a lot of people would prefer their Networks hidden for a little security. I know it isn't much, cause if someone wants to get that info it's not hard to get it. But for people who don't know or don't want to waste all the time to find the Hidden Network name can be turned away, for going through that extra step.
View 6 Replies View RelatedI'm going to move offices into a shared situation with 3 companies. Each company will want its own private network so there's no snooping between companies. I am planning on using VOIP for the phone system (Nextiva cloud based). Is it possible to set up the system so that each company has access to the VOIP system but yet remains sequestered in the their own network for everything else. I was hoping to do this with one data port at each workstation using Cisco SPA-303 phones. The way I understand this, is that the phone plugs in to the data port and you daisy chain the workstation off from each phone. Is this possible to do this while having the system I described? Another wrinkle is that I'd also like all the networks to be access shared printers.
View 7 Replies View RelatedI am using an ASA 5520 running 8.2(4). My objective is to get a VPN client to access more than one network on the inside of the network, i.e., I need to VPN in with an IPSec client and be able to establish tcp connections to servers at 192.168.210.x and 10.21.9.x and 10.21.3.x, I believe I am close to having this resolved, but seem to have a routing issue.
View 5 Replies View RelatedI currently have an 867vae router and a 1131ag ap setup with 2 vlans and 2 ssid's. I am in the process of baby proofing the house and would like to use the cisco plsk400 homeplug system to relocate my wap. I use 2 networks to seperate and filter the kids internet traffic from my own. It also allows me to shut the kids vlan when they shouldnt be on the internet.
As far as i can tell the plsk400 homeplug doesnt support 802.1q.... so is there any way i can keep the seperate networks/SSID's and the abilty to filter and turn off one of them at will without a trunked link to the router?
setting up networks with multiple locations and multiple wireless points.For example: My sisters' home has here modem in her main computer room, it has a Belkin router hooked to the modem. Then a line goes from there to my nephew's room where I tried to expand their network by adding another router. I really just wanted an access point, but they don't seem to sell these as much as they used to. Anyway, I had it working, but it was two different networks, NETWORK1 and NETWORK2. So they had to swap networks when moving around the house. what would be the best hardware setup to provide both sides of the house with some Hardwired access as well as wifi access? Right now, we have two routers, a DIR615 (or something like that) and a Cisco E1000, and again hardwire going from the main computer room to my nephew's room.Also, in my house, I have lots of stuff... I have an Actiontec Router from FIOS, feeding a small hub as well as a switch in my main room. Which then feeds a Ps3, Wii, laptop, Denon reciever, and Access Point... and also feeds my Apple TimeCapsule, which also feeds my printer. My wireless devices range from cameras, iphones/ipads, and a wifi unit (I forget what it's called, but it connects my DVR wirelessly to my network, and the DVR itself doesn't have wifi).
my question about my setup is, should everything be on one network... as in let the ActionTec handle most of the duties and use switchers and accesspoints to extend the network. Should everything be on the same wireless network and channels? Like if I used my access point to extend, do I want the same settings as my main wireless router, and would that be the same for the Apple Airport Extreme?Also, does having all these wireless networks going create any kind of hinderance on my performance. For example, the PS3 has some sort of wifi in it... it produces a SSID, but I never connect to it. Should I make sure that's off? And in my main room, should I go with just the AirPort extreme over using it and the Wireless Access point.
The original network had a Zylex router, Netgear Switch. There was 2 pc's, one XP and Win 7. There is also 3 tills connected too.There is VPN network connected too. This emits a wireless signal to connect to a scanning gun and is also used to administrate the entire network. I was told by the Administrator of that network that it shouldn't interfere with the wifi network.The job I was requested to do was to install 3 new wall plates as the Win 7 pc was using a Belkin wireless adapter. There was 2 put inside the office where the XP and Win7 pc's are located. The 3rd was just outside the office.Now all the ethernet connections work 100%. The wifi is another story though. It will show up in the connect too, when you try connect it will disappear/no response from AP/connect then disappear, these are random too. No order to when each is error is displayed. Even when I put in another router the exact same issues happen.I have tried to connect to both routers wifi when it wasn't plugged into the switch. Just the router's turned on with no cables plugged in separately of course, no joy same issue with both.
View 2 Replies View RelatedCan we connect different networks using switch without a router
View 4 Replies View RelatedI am using a EA4500 and use Linksys Smart Wi-Fi to manage the device. In the household we have multiple Apple i devices. Somehow the Linksys Smart Wi-Fi combined two separte i devices (iPhone 5 and a 4th generation iTouch) to one user.The devices actually have different names, but the Smart Wi-Fi is combining them into one device. So I can't use Parental Controls on one of the devices.
View 8 Replies View RelatedI want to connect my ps3, sky hd+ box and samsung smart tv. Upstairs is my wireless router and I have connected to this by using a power supply networking adaptor (duvelo). I have since purchased a cheap ethernet switch from ebay and plugged this into the power adaptor connection next to my ps3, sky hd+ and samsung smart tv downstairs. I thought by connecting these 3 devices to the switch (which is connected to the duvelo adaptor) I could have all 3 devices simultaneously connected online. However, I still can only have 1 ethernet cable in the switch at once and hence only connect 1 device at a time.
View 2 Replies View Related