Multiple Networks Different Subnets Windows 7?
Jan 24, 2013
I have a Windows 7 Pro Desktop with an on-board Ethernet and an Axis USB To Ethernet adapter. The on board Ethernet is configured as dhcp and obtain the address 10.162.146.123 with 255.255.255.0 subnet. The Axis USB to Ethernet adapter is static ip configuration with 10.38.25.37 and 255.0.0.0 as subnet. Under the adv settings I have also another ip 11.38.25.37 with 255.0.0.0 subnet. When the Axis is communicating 10.38.0.1 network I can not access the internet using the on board Ethernet 10.162.146.123. I have to disable either one of the cards to access one network at a time.
View 3 Replies
ADVERTISEMENT
Oct 24, 2011
With traditional classful subnetting, the same number of host bits is used to designate the subnet ID for all the resulting subnetworks. This type of subnetting always results in a fixed number of subnets and a fixed number of hosts per subnet. For this reason, this is known as fixed-length subnetting. The decision about how many host bits to use for the subnet ID is a big planning decision. There are two considerations when planning subnets: the number of hosts on each network, and the number of individual local networks needed. The table for the subnet possibilities for the 192.168.1.0 network shows how the selection of a number of bits for the subnet ID affects both the number of possible subnets and the number of hosts that can be in each subnet. One thing to keep in mind is that in all IPv4 networks, two host addresses are reserved: the all-0s and the all-1s. An address with all 0s in the host portion of the address is an invalid host address and usually refers to the entire network or subnetwork. An address with all 1s in the host portion is used as the local network broadcast address. When a network is subnetted, each subnet contains an all-0s and an all-1s host address that cannot be used for individual host addresses.
View 2 Replies
View Related
Mar 2, 2012
I've currently got my ASA (5505) serving a /28 public subnet. I've ran out of IPs, so my DC has issued me an additional /24 subnet that they have routed to my ASA. What needs to be done on my ASA so be able to use these new addresses? I've been trying to search and not been able to find a good answer (some say I shouldn't have to do anything, everything else references NATing, which I currently don't do and would rather not do).The servers I assign these to, I'd like them to have the public ip assigned directly to them.
View 5 Replies
View Related
Feb 20, 2012
Is it possible to have multiple public IP addresses that are from different subnets going through one router? I have been told that this is not possible with most routers and that I would have to spend a lot of money on a router to be able to do it. I am still not totally clear on what defines a subnet even after reading up on them. What I am trying to achieve:
-My office has 10 computers.
-All would be connected to one router.
-My internet service provider has provided me with 10 public IP addresses, that are all very varied (which I asked for)
View 3 Replies
View Related
Aug 26, 2011
I am setting up my home lab to practice and play around.I have VMWARE ESXi environment with two workstations as my servers.I would like to setup two domains with two domain controllers but i want each domain to have its own subnet.So this is my setup. I have Cable modem from cablevision , thay connects to my router which is Apple Airport which acts as the DHCP server. DNS server and default gateway. The network on the router is 10.0.1.xThen i have two switches . One is a 5 port unmanaged switch that connects to the three physical desktops .Then i have a Cisco small business switch SG200-08 that connects to my ESX servers and NAS. Now currently all is good and working but like i said all my machines physical or virtual get an IP that is 10.0.1.x and they get all this from the router. And i think i can setup two domains with two domain controllers without an issue and they will all get an IP address of 10.0.1.x. This is all good but i want to have one domain on one subnet and other on another so for example one domain will have 10.0.1.x and other 10.0.2.x. I am just not sure what i need to to get this setup like this. I know my SG200-08 supports vlans and i am pretty sure on the apple router you can only have one subnet i think. So can i do this with my current setup by setting up a DHCP server with two scopes ?
View 3 Replies
View Related
Mar 26, 2013
I have an ASA5510 that is connected to outside for WAN, inside for LAN (10.22.254.0/24), and a iSCSI switch plugged into Ethernet 0/3 (10.22.244.0/24). I can ping the Eth0/3 interface (10.22.244.1) but I can't ping across that interface from WAN or LAN side.
START CONFIGURATION
ASA Version 9.1(1)
!
hostname ASA5510
[Code].....
View 7 Replies
View Related
Jun 23, 2011
NAT command on 8.4? I am trying to PAT multipule Inside subnets to an IP address. With the example I found I can only PAT one subnet. If I do it the way I have below, it will end up with the last subnet (3.3.3.0) stay in the config. What is the best way of doing it? I have about 20 inside subnets I need to PAT.
object network obj-Inside-sub1
subnet 1.1.1.0 255.255.255.0subnet 2.2.2.0 255.255.0.0subnet 3.3.3.0 255.255.0.0nat (inside,outside) dynamic 199.246.5.2
View 5 Replies
View Related
Jan 22, 2013
Here's what I want to do with my RV042: I have a bunch of devices, including a server, inside my network at 192.168.1.100
I've set up VPN using PPTP. It works, but if my clients have their own remote DHCP set up to 192.168.1.x, they can't get to the server. If their home DHCP is 10.x.x.x., everything works
I am considering changing my internal network to something obscure.
My server has two NICs. So I thought, I why not set one address up to 10.x.x.x But the two nets can't ping each other. I tried using "multiple subnet" on the RV042, setting up 10.1.1.1, but no luck.
View 1 Replies
View Related
Aug 5, 2011
We have 4 RV 042 routers and cisco router at HQ, we have Site to Site VPN tunnels in between, All branch offices are connected to HQ via S2S VPN tunnels
10.10.1.0/ 24 HQ
10.10.2.0/24 Branch 1
10.10.3.0/24 Branch 2
10.10.4.0/24 Branch 3
10.10.5.0/24 Branch 4
now lets say i am branch 1, i can access 10.10.1.0/24 network but cant access 10.10.5.0/24 network, means i dont have branch to branch connection, it should be through HQ, means my RV042 at brnach should fwd all traffic to HQ for another branches also. Under VPN tunnel if i try to configure remote destination 10.10.0.0/21 its not allowing me it says network overlaping with local network, how i can sole it, I know how to do in cisco, we can permit those networks in access lists.
View 1 Replies
View Related
May 23, 2011
I have an existing pair of PIX 515E that has two interfaces. One connected to the public internet via my ISP and one internal.
I recently ran out of IP's and had the ISP route an additional block to public IP of my firewall. This isn't working for some reason and I'm trying to figure out why.
The "ip address outside XXX" command defines the outside address and I don't see any way to add a secondary sub net.
I tried just adding a rule to the firewall for one of the IP's in the new subnet, but I can't seem to get traffic to pass though the device.
View 1 Replies
View Related
Aug 16, 2011
We have Point to point T1 environment where 3 additional WAN sites get internet access through our RV042. When we setup load balancing we have problems with https traffic, so we setup protocol binding for https and everything worked great from the local LAN. When trying to access https content from the remote LAN across the WAN the sites failed and I see no option to add additional subnets to the protocol binding. Is there a command line feature that supports adding additional subnets for protocol binding or is the local LAN the only option?
View 7 Replies
View Related
Nov 17, 2011
The ASA device is going to be the gateway for multiple distinct inside IP subnets. We can have have a unique outside IP address to correspond to each inside IP subnet if needed, but we need some means for a VPN client or a site-to-site VPN to have acess to a pre-definied IP subnet (i.e. if customer A establishes a VPN connection, they have connectivity to IP subnet X; customer B establishes a VPN connection, they have connectivity to IP subnet Y, etc.).Currently, the two inside IP subnets are 10.10.0.0/16 and 10.20.0.0/16. We will be adding more.The problem we are facing is that we cannot reach the VLAN 201 from the ASA we believe this is because. I have setup two addresses on port 0/1 Vlan1, 10.10.20.2 and 10.20.20.1 as an alias. How can we make traffic for the 10.10.0.0/16 subnet untagged and traffic for the 10.20.0.0/16 subnet tagged for VLAN 201.
View 1 Replies
View Related
Jan 4, 2013
I have setup 15 x RV180W's so far for a particular client.They have requested that we add a Corporate Wireless VLAN for their laptop users (not guests) and add a Special Use WiFi VLAN for a particular mobile platform that is being deployed (in this case we need 2 separate WiFi VLANs to ensure compliance).Also, none of the VLANs can talk to eachother and they have their own subnets.I have the Wireless and VLANs setup, no problem... but I am having an issue wiht the VPN settings.I have the wired network's subnet working fine. But I do not know how to add the subnets for both Wireless VLANs to the traffic selection.The IP schemes will not allow me to just select a large subnet... here are some examples:
Wired VLAN: 10.10.x.y
Corporate WiFi VLAN: 10.15.x.y
Special WiFi VLAN: 10.18.x.y
x is the octet that defines the physical unit location (unit 1 = .23, unit 2 = .24, etc...) y is the octet the host.Since they are not in a contiguous block, I cannot just use a larger subnet mask.I can add multiple traffic selection rules to the ASA5515 at HQ, so that side of the tunnel is perfect... I just don't know how to add the three VLANs to the RV180. Is it as simple as using commas or semicolons?
View 1 Replies
View Related
Jan 5, 2012
I am new to Cisco products. We have currently got a Netgear FVX538 running in front of a few servers. We currently have 2 ranges of IP addresses provided to us on 2 separate subnets. We configured the netgear box with the first IP addresses of each subnet as the IP address of each of the primary and secondary LANs. This then allowed us to set the gateway addresses of servers on the network to either of those 2 addresses, depending on it's range.
This all worked fine - except for the fact that the Netgear box is incredibly flakey, so we decided to get a Cisco box.
We have gone for the SA520, which I have been trying to configure this afternoon. Unfortunately I am now having concerns as to whether it is possible to configure 2 separate subnets internally on this box in the same way we have done with the netgear box. ie - classical routing, one incoming WAN interface with multiple subnets?
View 5 Replies
View Related
Jun 29, 2012
I have a Cisco 2901 with the 4port gigabit ethernet switch module that I'm trying to get configured to have a seperate subnet for each port. So far I have it set up so each subnet is a vlan, then on each port I use the switchport access vlan command to tell it which subnet I want that port to be on. However, there is one port that I need to have 2 subnets on. The way I found to do that was to use switchport trunking on that port, but it doesn't seem to be working properly. how they would configure this? Right now I have vlan 101 as x.x.x.17/28 and vlan 103 as x.x.x.53/30. I think where I'm getting hung up is the proper association between the physical port and the vlan subnets.
View 5 Replies
View Related
Dec 20, 2010
We have a 6509 that was connected to 2 other locations(location A and B) and our local lan (location MAIN). We wanted to move the location A and B to a 3750 switch and only allow the traffic that needed to access our location MAIN to come through the firewall. The only problem I ran into is that before location A and B were on different interfaces so in the 6509 firewall the routes for traffic to our MAIN location was done by static routes.
I.E.
static (MAIN_intf,A_intf) 192.1.1.72 10.94.10.72 netmask 255.255.255.255 0 0
static (MAIN_intf,B_intf) 192.2.2.72 10.94.10.72 netmask 255.255.255.255 0 0
[Code]....
because it has a static overlap, which makes sense to me, but my question is how do I configure the network to get this to work? Do I have to reconfigure my network and access-list? Do I need to add more ports between the 6509 and 3750? I'm not sure if this is the best way to do what we want. If something is not clear I'll try my best to explain the setup, but I just took over for our I.T. guy when he left.
I put 10.10.10.72 instead I should have put 10.94.10.72. the routed port is on a different subnet than the computer I'm trying to access.
View 4 Replies
View Related
Sep 16, 2012
I have an ASA which is managing internet access from mutiple VLANs configured on a 3560 switch. I want to be able to limit the 100MB internet connection on the ASA on a per subnet (VLAN) basis for the multiple subnets configured on the switch..
so for example
VLAN10 - 10.0.10.0 - limit to 5MB
VLAN20 - 10.0.20.0 - limit to 10MB
VLAN30 - 10.0.30.0 - limit to 3MB
View 7 Replies
View Related
Nov 27, 2011
We have RV 042 deployed for internet access/firewall purposes. Due to growing number for Wireless devices and also to separate WLAN traffic from wired devices, we have created a separate VLAN/IP Subnet for the wifi devices. We are having trouble accessing the internet from the WiFi VLAN/IP Subnet. Cisco 3750 is layer 2 and layer 3 device. We have VLAN 1 (10.10.10.0/255.255.255.0), all wired devices and RV 042 are part of VLAN 1. Connectivity to internet from VLAN 1 is good. VLAN 2 (192.168.1.0 / 255.255.255.0) was created for wifi devices, 3750 does the inter-vlan routing, I have enabled the multiple subnet feature on the RV 042 and added 192.168.1.2 / 24 to the subnet list, we still have issues accessing internet from vlan 2 devices.
As a workaround, I shutdown vlan 2 and added 192.168.1.0/24 as secondary address to the VLAN 1 interface on 3750 and i was able to access internet from 192.168.1.0/24 network with wifi devices also on vlan 1, we want wifi devices to be on separate vlan / ip subnet. Looking at the documentation for RV series routers, it talks about supporting multiple subnets access to internet by enabling multiple subnet feature but it doesn't seem to work.Are there restrictions on having multiple vlans?
View 4 Replies
View Related
Mar 25, 2012
3750 can not support multiple subnets in it's DHCP server pool config.
Is this an issue that can be fixed with a different iOS or is there a different Cisco switch that I can replace the 3750 with that will handle multiple subnets within an individual pool?
View 1 Replies
View Related
Feb 14, 2012
I am having trouble setting up two networks.Basically, i want one 'private' network and one public network. The problem is, the private network can't access the internet.(Network 2)
Network 1(Public) works fine as i don't want them to access Network 2.Here's how it is setup.
Internet
|
Router/Modem (Network 1)
|
Server NIC1
Server NIC2
|
Switch - (Network 2)
Network 1 can access the internet and shared files on the server.
Network 2 can access Shared files on the server (which is what i want) but cannot access the internet.
Router/modem IP is 10.10.1.254 subnet 255.255.255.0
Server NIC 1 IP is 10.10.1.252 subnet 255.255.255.0
Server NIC 2 IP is 10.10.1.251 subnet 255.255.255.0
How can i get computers in Network 2 to access internet?
View 5 Replies
View Related
Aug 30, 2011
Explain the risks of not using multiple networks on a 300 host LAN
View 1 Replies
View Related
Feb 11, 2012
I have a pair of RV082 routers and I'd like to configure gateway to gateway VPN tunnel as described in a cookbook, "How to configure a VPN tunnel that routes all traffic to the Remote Gateway," (file name Small_business_router_tunnel_Branch_to_Main.doc). I followed this cookbook and found that my while the Main office has internet connectivity, the branch subnet doesn't have internet connectivity.
Routing does behave as advertised, where all traffic does go to the main office. However, the 192.168.1.0 subnet in the branch office does not get internet connectivity. I've read in other posts that the Main office router will only provide NAT for the local subnet, not the branch office subnet. Is there a way to configure the RV082 router to provide NAT for all subnets?
If not, which Cisco product will provide the VPN Tunnel connectivity as well as the NAT for all subnets? Can the RV082 be used as part of the final solution or are my RV082s a wasted expenditure?
Following is the configuration that I'd implemented, (real IP and IKE keys are bogus).
Gateway To Gateway
Remote Main Office
Add a New Tunnel
Tunnel No. 1 2
Tunnel Name : n1-2122012_n2-1282012 n1-2122012_n2-1282012
Interface : WAN1 WAN1
[code].....
View 2 Replies
View Related
Jan 11, 2012
I have 3 Macs (OS 10.6.8) and one PC (Windows 7) at work. They are all connected to the company network for internet and access to shared network drives.The computers are used for media (mostly video) production and we need to move large files between the computers easily and quickly. The current network (company wide) is slow and unreliable, so I would like to create a separate network for these four computers and have them connected to both the company network and the office room network. Each computer already has two network ports and I have a router I can use.
View 3 Replies
View Related
May 19, 2012
We have 36 cctv cameras slowing down our oracle network pc's all in same subnet. I want to remove the dvr's of cctv to a separate network to improve performance. How to accomplish that with a Rv042 linksys router? Or is there any other better way around. 5 Users access the cctv cameras all the time.
View 2 Replies
View Related
Feb 16, 2013
I am currently working on a project that needs to install a router (or just a network device) that can offer 2 or more DHCP networks. We have been searching a network device for this but haven't gotten any good news yet. Any model or device that can fulfill this requirement?
View 6 Replies
View Related
Aug 3, 2011
How do you setup multiple networks on one router? Is it as easy as changing subnets?
View 8 Replies
View Related
Sep 20, 2011
I currently have a hub-and-spoke VPN configuration with 6 ASA 5505's at remote sites all connected to an ASA 5510 at HQ via IPSEC lan-to-lan tunnels. My current configuration allows hosts on the remote site networks to talk to hosts on the HQ network, but not to hosts on the other remote sites.I have receieved a request to allow comminucation between the remote sites as well, with traffic all routed through the 5510 at HQ.
View 1 Replies
View Related
May 20, 2013
Im using 2 TP-Link TL-WA7510N to bridge a internet connection the connection is using a captive portal for my guests via pfsense. What i would like to do now is run a pc on the same connection without using the captive portal .So basicly i would need 1 secure network for my single pc and the one with captive portal for my guests.
View 1 Replies
View Related
Nov 19, 2012
My neighbor and I were wondering if it is possible to combine our respective internet connections in order to gain a faster connection overall. What would be ideal would to have a wireless router in one of our houses, that is simultaneously connected to both of our ADSL routers, and to which both of us are able to connect. Do I need a specific type of router?
View 5 Replies
View Related
Jan 9, 2011
Adding a second DAP-1522, They have 1 DAP-1522, they set that up useing the WAP(button on the side), This one is running in the frontroom of the house and the 2nd bridge will be running in the bedroom of the house.She has tried to click on the WAP button on both Dap-1522's and then the router to sync but thats not working, from what we can tell. I think I will need to manually config them now that a second one has been introduced.the frontroom Bridge is 192.168.0.50, but we cant find the ipaddreess for the second dap-1522 at this time. So question to all, if I can - Is there a way to identify all of the Dap-1522's on the network or anything that is connected on the network. as the DIR-655 is only showing 2 things connected?Right now I wish she would have listened too me and had her house wired for ethernet when the house was being built.
View 1 Replies
View Related
Apr 10, 2013
I am looking to create an office network with each person having internet access but on a private network. however everyone will need to be able to access a communal printer. would they be able to see it if they were all on a different subnet or would i need to set up vlans?
View 4 Replies
View Related
Jul 3, 2012
I would like to associate multiple IPv4 networks with one physical interface in the router. All those multiple networks share the same broadcast domain(VLAN 5). I am aware that it's not possible to have multiple subinterfaces in the router with the same "encapsulation dot1Q 5". Am I correct that only option here is to configure all those networks as a secondary network to router physical interface? Or are there other possibilities than secondary addresses?
View 4 Replies
View Related
May 22, 2011
I have 3 networks coming on DMZ (VPN) interface. Only one network is able to ping the DMZ interface. See below networks coming i on the DMZ.
10.132.24.0/2410.132.25.0/2410.132.26.0/24 Only the 10.132.26.0/24 netork works as it is in the same range as the DMZ interface.
allowing the other two networks to communicate. I've attched the diagram and configs for your perusal.
View 1 Replies
View Related