I am looking to create an office network with each person having internet access but on a private network. however everyone will need to be able to access a communal printer. would they be able to see it if they were all on a different subnet or would i need to set up vlans?
View 4 RepliesI have 3 networks coming on DMZ (VPN) interface. Only one network is able to ping the DMZ interface. See below networks coming i on the DMZ.
10.132.24.0/2410.132.25.0/2410.132.26.0/24 Only the 10.132.26.0/24 netork works as it is in the same range as the DMZ interface.
allowing the other two networks to communicate. I've attched the diagram and configs for your perusal.
I'm going to move offices into a shared situation with 3 companies. Each company will want its own private network so there's no snooping between companies. I am planning on using VOIP for the phone system (Nextiva cloud based). Is it possible to set up the system so that each company has access to the VOIP system but yet remains sequestered in the their own network for everything else. I was hoping to do this with one data port at each workstation using Cisco SPA-303 phones. The way I understand this, is that the phone plugs in to the data port and you daisy chain the workstation off from each phone. Is this possible to do this while having the system I described? Another wrinkle is that I'd also like all the networks to be access shared printers.
View 7 Replies View Relatedi have Cisco 5505 and i configured a remote VPN clients. here is my scenario
Cisco switch 2950 === holds two private network 192.168.8.x and 192.168.4.x
vlan 2 outside interface - Eth 0/0 155.155.155.x
Vlan 1 inside interface -- Eth 0/1 192.168.8.180
VPN pool ip address = 192.168.8.100 --110
I drag i cable from my Cisco switch and put in to Eth0/1. and i want to access this two private networks 192.168.4.x and 192.168.8.x . Now i can access to 192.168.8.x . But i can't access 192.168.4.x ..
I have the following configurations in cisco CISCO7606 (R7000). Its meaningful to have the below configuration, wherein , we are allowing multiple vlans on the access port?
interface FastEthernet4/45
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 124-127,423,478,493,578,699,751,787,895,987,1981
switchport mode access
end
interface FastEthernet4/46switchportswitchport trunk allowed vlan 124-127,423,478,493,578,699,751,787,895,987,1981switchport mode accessend
the site has a private wireless network for which I pay a yearly access fee. This gives me a code I can use to gain access each time I connect. We used to be able to have all our family's laptops, etc., connected at the same time using this code, but the site has recently changed the configuration so that we can't do this. Is there any way we can share the connection made by one computer so that we can all access the Internet at the same time? The site is in a remote location that gets poor mobile data coverage and landlines are not an option. The yearly fee is already high, so I can't afford to pay for multiple subscriptions.
View 1 Replies View RelatedI just bought a WRT54GL which is working perfectly. I needed it to extend my home network for my kids (I have not a very fast internet connection and my kids are eating all of it... With the WRT54GL I can choose how much they can have. So my own network has a netgear modem and a netgear wifi access point which is in this network : 192.168.0.x.
This network is not blocked in any way (just password protected). For my kids network, the WRT54GL gives addresses in this network : 192.168.1.x and is limited in speed. Everything is perfect, I have internet connection on both of my network, There is just the problem that I cannot access my printers, my servers, my computers.... that are on the 192.168.0.x network from 192.168.1.x. Is there a solution ? I already tried to force the WRT54GL to go to 192.168.0.x network but no more connection. Should I "bridge" the two networks ? How can I do it ?
I have a nac guest server 3315 appliance with 4 NICs. I want to connect each NIC to 4 different networks without allowing traffic between them. So RADIUS interface will be different from sponsor/admin interface to the NGS. how to achieve this. I have created and assigned a static IP address using system-config-network, but when i do ifconfig i dont see the remaining 3 NICs and the web interface doesnt seem to have provision to create this interfaces.
View 3 Replies View RelatedI'm usually not working with this product, but this is what I'm trying to do.I have 2 internal networks setup on our Cisco ASA 5505 firewall. (not done by me, I'm a new to this product)I'm trying to access a server on one network from a PC located on the other internal network. (preferable through the web gui)When I try "Packet Tracer" from interface "Trust4" it fails on the NAT phase.(Source ip: 10.0.4.99, Destination ip: 10.0.6.99)
When I check the NAT rule, it says:
Type Source Interface AddressDynamic any outside outside.
i have two cisco 2800 routers , and i have three different networks , so can cisco routers supports more than one private network example,My First location i have one public connection of 200.100.100. 1 and private network of 192.168.1.x network and the second router i have one public connection of 200.100.100.10 and two private networks of 192.168.50.x and 192.168.60.x , So can i route my first location to this two different networks , because my router have only two FastEthernet connection , so how it's possible or not.
View 3 Replies View RelatedConnected our Brother MFC-8820D printer/scanner/fax directly to one of the 4 Ethernet ports on the back of the DIR-655 in our new install with this router, and all computers can print to it, whether connected via an Ethernet cable or via wireless, but none of the printers can scan. We just get an error message. Scanner driver is installed on all computers. Same printer worked fine via Ethernet on a Windows small business server for printing and scanning. Windows server no longer used or connected. Only DIR-655 as we are dumbing down and getting rid of our Windows server and have gone to a NAS solution connected to the DIR-655.
What can we do to make the scanning work on our Multifunction printer?
I have two private networks and want/need to route traffic between them. I also have an ISP connection and want/need to provide internet to at least one of the private networks. Providing internet access to both is not required or desired.
Can this be accomplished with an RV042? If so, how?
P.s. The problem space, once again, in a non-narrative form with some addresses thrown in:
Private Network A: 192.168.200.0/24
Private Network B: 10.50.3.96/27
ISP Network C: 192.168.0.0/24 192.168.0.1GW 192.168.0.2 is WAN1 address on RV042
Required Traffic Flow
A <--> B
A ---> C
I have a new customer that needs to send data to us occasionally, we normally install the Cisco VPN Client on their PC, but this customer has the same private network we do.
I know this could be done with NAT Policy on my ASA 5510 with a site-to-site VPN, but the customer does not want to change the network hardware or addressing. They have cable router with no VPN capability, and they don't want to spend any more money on this project.
Can this work if their are no duplication of IP addresses?
how to redistribute routes between three independently managed private networks.
Currently: See attachment The two buildings managed by Company 1 are connected by 4x1GB fibre channel ports on Cisco 3750G Standard Image switches. Static routing is used between the two building and static routes are used to direct traffic to Company 2 and Company 3 via routers managed by their respective companies. No NAT is required as all three companies use separate private address schemes.
Network Improvements: See attachment To increase network resilience Companies 2 and Company 3 are planning on installing new routers in building 2. Companies 2 and 3 use Dynamic routing protocols on their internal network. Incoming and outgoing resilience is required in all three companies. There is no direct connectivity between Company 2 and 3.
I would like the following questions answered:
1. Is dynamic routing needed in Company 1?
2. Given that only 4 devices are managed by Company 1 will RIPv2 work? NB. Company 2 and 3 have very large networks (3000+ sites).
3. Would route redistribution be best performed on Company 2 and 3’s CE routers?
4. How can route redistribution be controlled by Company 1?
We have a private network, multiple vlans etc. for our domain users/employees across several amenities. We also have a Public network, that we have managed by a 3rd party for guests/conference rooms/attendees.Private network is all static ips, mac restricted port security, as strict as possible from a security and PCI Compliance standpoint. The public network is all DHCP with hundreds of users. Having them physically separate has always been the best option. Separate switches, server, and I even have the uplinks separated on a 3825 router. However, unfortunately it seems as though that luxury is coming to an end.One of the meetings that is taking place is going to be at one of our outer amenities so I've got to push that "public" network through my network, over my backhaul to the other side.
My suggestion was to create a new vlan on the switches with the shortest path possible to get where it needs to go. This way the traffic never goes through our ASA, and it has a small footprint on our network, it plugs into the switch access port with the dedicated vlan at the entry point into our network, and leaves from an access port on the other end. To me that seems to be the best/most secure way to handle it. We're also in the process of rolling out Public Wifi through the entire property and since we'll want to push both Public and Private vlans over it....merging the two networks to a point is only inevitable. Especially since it will be going through a controller and the property covers a good 7000 acres.
A good IDS/IPS...other than already having port security on every port, I'd definitely like to know if somebody inadvertently cross connects the two networks and it starts flooding whatever vlan access port it's plugged in to with dhcp...especially since a lot of the laptop users on the domain are set to DHCP first with a static in the alternate for working at the office and remote.
Currently a network consists of two subnets, one subnet is behind a ASA and the other behind a PIX, both connecting to the ISP's routers. If the PIX is retired, is it possible to create/consolidate the two networks protected by the ASA5510 with the default gateway being the ISP?
How can two private networks be protected by the ASA5510? One conceptual way is to create the VLANS on a layer 3 switch, on the "inside" interface of the ASA. In this senario what would the "inside" network's IP address? If the above is possible, how would natting occur?
Is there an efficient configuration to protect two networks protected by the 5510, other than creating a DMZ?
Is it possible to create two private networks with same level of security, 100 on a three network interface connections?
We have many remote offices that we want to add public wifi and a couple of other services that would be completely outside of our internal network. Each office has a 3750 with plenty of open ports. How can I safely create a vlan for public access on these switches which currently have our internal network on. I have read that people are doing this to save on the cost of purchasing a dedicated switch. Some people are using access lists and one person mentioned creating a private vlan for the public network. I looked up private vlan and it seemed bit confusing.
View 3 Replies View RelatedI am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?
what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature
I am having trouble setting up two networks.Basically, i want one 'private' network and one public network. The problem is, the private network can't access the internet.(Network 2)
Network 1(Public) works fine as i don't want them to access Network 2.Here's how it is setup.
Internet
|
Router/Modem (Network 1)
|
Server NIC1
Server NIC2
|
Switch - (Network 2)
Network 1 can access the internet and shared files on the server.
Network 2 can access Shared files on the server (which is what i want) but cannot access the internet.
Router/modem IP is 10.10.1.254 subnet 255.255.255.0
Server NIC 1 IP is 10.10.1.252 subnet 255.255.255.0
Server NIC 2 IP is 10.10.1.251 subnet 255.255.255.0
How can i get computers in Network 2 to access internet?
Explain the risks of not using multiple networks on a 300 host LAN
View 1 Replies View RelatedI'm currently trying to configure a Site to Site tunnel between an IOS Router and an ASA 5505 running 9.1
When the private subnet of the IOS Router was 10.0.0.0/24 and the private subnet of the ASA was 172.16.1.0/24, it connected fine.
I'm now trying to set it up where both private networks are 10.0.0.0/24, and created network objects, edited the ACL for interesting traffic, and created the twice NAT translation rule, but the tunnels aren't coming up.
There is the IOS Router(R1) and the ASA(F2). In between them is one Internet posing router that is just set up to allow both sides to reach their WAN addresses.
R1 and F2 have private network (10.0.0.0/24) and need to communicate. Twice NAT can be done all on the ASA to allow this, but I must be doing something wrong. The way I understand it, is that the R1 should see the traffic coming from 10.51.0.0/24 and sending to that traffic. The ASA will take that traffic, and the inside network should see it come inbound as 10.50.0.0/24. So the F2 private network communicates with 10.50.0.0/24 and R1 private network sends traffic to 10.51.0.0/24.
I turned on "Debug crypto ipsec" and "debug crypto isakmp" but no output is showing up or giving any hint that it is trying to establish anything.
R1#show run
version 12.4
hostname R1
crypto isakmp policy 50encr 3desauthentication pre-sharegroup 2crypto isakmp key cisco address 10.2.0.254
[Code]......
I've been trying to connect my printer to my wireless router/modem. The install program is giving me the following error {The PC and the printer are connected to different networks(192.168.15.0 and 192.168.0.0). They must be connected to the same network. This can happen when you use the manufacturer's default network name (SSID) and another nearby network is using the same name.} I just had the computer built and have been setting it up. How do I know which is the right IP address?
View 6 Replies View RelatedSo basically I need to hook up a HP LaserJet P2015 to a business and home network. LaserJet P2015 user guide. I would like to keep the printer's ip static so it will stay the same on each network individually. am using a business router (Linksys RV120 W Wirless-N VPN Firewall) with two VLAN (business and home network) built using this router. Also I have two access points both being used to expand this signal through out the building, but not as an extender. They are two Linksys WAP54G access points. The access points are used to expand the home network, and not the business network.
View 1 Replies View RelatedAbruptly internet access disappeared. It's a router issue, none of the computers here can connect. Further, I can't access the router through a browser - 192.168.0.1 results in a "Firefox cannot connect" message. I've tried resetting the DNS to no avail. I'm typing via cell phone and it's annoying, but I'm willing to try about anything.
View 4 Replies View RelatedI have 3 Macs (OS 10.6.8) and one PC (Windows 7) at work. They are all connected to the company network for internet and access to shared network drives.The computers are used for media (mostly video) production and we need to move large files between the computers easily and quickly. The current network (company wide) is slow and unreliable, so I would like to create a separate network for these four computers and have them connected to both the company network and the office room network. Each computer already has two network ports and I have a router I can use.
View 3 Replies View RelatedWe have 36 cctv cameras slowing down our oracle network pc's all in same subnet. I want to remove the dvr's of cctv to a separate network to improve performance. How to accomplish that with a Rv042 linksys router? Or is there any other better way around. 5 Users access the cctv cameras all the time.
View 2 Replies View RelatedI am currently working on a project that needs to install a router (or just a network device) that can offer 2 or more DHCP networks. We have been searching a network device for this but haven't gotten any good news yet. Any model or device that can fulfill this requirement?
View 6 Replies View RelatedI have a Windows 7 Pro Desktop with an on-board Ethernet and an Axis USB To Ethernet adapter. The on board Ethernet is configured as dhcp and obtain the address 10.162.146.123 with 255.255.255.0 subnet. The Axis USB to Ethernet adapter is static ip configuration with 10.38.25.37 and 255.0.0.0 as subnet. Under the adv settings I have also another ip 11.38.25.37 with 255.0.0.0 subnet. When the Axis is communicating 10.38.0.1 network I can not access the internet using the on board Ethernet 10.162.146.123. I have to disable either one of the cards to access one network at a time.
View 3 Replies View RelatedHow do you setup multiple networks on one router? Is it as easy as changing subnets?
View 8 Replies View RelatedI currently have a hub-and-spoke VPN configuration with 6 ASA 5505's at remote sites all connected to an ASA 5510 at HQ via IPSEC lan-to-lan tunnels. My current configuration allows hosts on the remote site networks to talk to hosts on the HQ network, but not to hosts on the other remote sites.I have receieved a request to allow comminucation between the remote sites as well, with traffic all routed through the 5510 at HQ.
View 1 Replies View RelatedIm using 2 TP-Link TL-WA7510N to bridge a internet connection the connection is using a captive portal for my guests via pfsense. What i would like to do now is run a pc on the same connection without using the captive portal .So basicly i would need 1 secure network for my single pc and the one with captive portal for my guests.
View 1 Replies View RelatedMy neighbor and I were wondering if it is possible to combine our respective internet connections in order to gain a faster connection overall. What would be ideal would to have a wireless router in one of our houses, that is simultaneously connected to both of our ADSL routers, and to which both of us are able to connect. Do I need a specific type of router?
View 5 Replies View RelatedAdding a second DAP-1522, They have 1 DAP-1522, they set that up useing the WAP(button on the side), This one is running in the frontroom of the house and the 2nd bridge will be running in the bedroom of the house.She has tried to click on the WAP button on both Dap-1522's and then the router to sync but thats not working, from what we can tell. I think I will need to manually config them now that a second one has been introduced.the frontroom Bridge is 192.168.0.50, but we cant find the ipaddreess for the second dap-1522 at this time. So question to all, if I can - Is there a way to identify all of the Dap-1522's on the network or anything that is connected on the network. as the DIR-655 is only showing 2 things connected?Right now I wish she would have listened too me and had her house wired for ethernet when the house was being built.
View 1 Replies View Related