I know that you shouldn't update router firmware from a wireless connection. The other day, somebody told me that you shouldn't configure a router(such as changing passwords, channels, etc) from a wireless connection. I change my router settings from a wireless connection all the time.
View 1 RepliesI want to set up a WiFi internet connection for a campus. I plan to use 4 routers. the first one is directly connected to the internet. I want to share internet access wirelessly with the other routers. Each of the routers should be a hotspot for each of the four blocks in the campus.
View 1 Replies View Relatedi got a problem in configuring a VPN Connection for our Colleagues (Laptops & Iphones 4/4S/5) We got an RV042G .
A WAN Connection from Deutsche Telekom AG with Static IP connected in WAN1. Configured for PPPoE. Ive got configured a Port Forwarding on our SBS 2011 Server for OWA and other Services on web. I´ve got extreme Problems configuring VPN Connections. We use Quick VPN, other tools got to much buttons to click .
1st i configured a Group VPN , with FQDN (Remote Group) Local Group (IP only) . i configured 2 users. Then on a Laptop connected to the internet through an Hotspot Connection of an Iphone.
I entered the WAN IP .. Username. Password. Pressed ENTER. I get to the point of Verifyiing Network, and after it timeout with Remote Gateway not responding. Do you want to wait. If i Press Yes, after max. 1 minute there comes the message again.
I looked in the VPN Summary, and i see, that my username was connected through VPN for seconds, but then disconnected. Do i have overseen an option to configure??
I bought a Linksys WRT54GL wireless router. Right now it's running unsecured and open. How to configure it to a secure connection?
Security Type options are: Shared, WPA2-Personal, WPA-Personal, WPA2-Enterprise, WPA-Enterprise, and 802.1x
Encryption Type options are: None, and WEP
Got road runner already get internet with wifi router, but want to set up password protection for internet access. the wifi is default now.
View 1 Replies View RelatedI need to front-end my ISP's router with another, giving me a DMZ. I have bought an EA2700 for this but I can't find how to configure it.
I plan to have the DMZ network as 10.1.2.0/24, with the ISP's router at 10.1.2.254 and the EA2700's "upstream" connection as 10.1.2.1. The internal network (where most of the clients reside) will then be 10.1.1.0/24, with the EA2700 itself at 10.1.1.254 and a DHCP range 10.1.1.100 upwards.
On the basic setup screen I've set the Internet connection type to fixed IP, 10.1.2.1; I've set its default gateway and DNS1 as the ISP's router at 10.1.2.254. Then further down in network setup I've entered the *internal* address 10.1.1.254 and set the DHCP range and netmask appropriately. I'm getting the error message "The IPv4 address and gateway are not in the same subnet mask". But the only gateway I've entered is the one by which the *EA2700* knows how to route upstream traffic, viz the ISP's router at 10.1.2.254. Or am I misunderstanding?
More fundamentally, can the EA2700 be configured in this way?
I've created two configurations. One for the router side and one for the AP point side. However, I am having trouble getting the internal AP to bridge to the router properly. It is my understanding that the Wlan-GigabitEthernet is the internal interface connecting to the AP and the BVI1 together. I can't ping any ip address on the router side from the ap and the radio is active and we can see it but it seems that it doesn't give an ip address. [code] Is it a VLan issue or an ip issue but I could use a second opinion. I've included both configurations.
View 1 Replies View RelatedI am using a broadband internet of a provider named BSNL,through a simple modem. Recently I got a Beetel 450BX1 ADSL2 + Router and want to use the wireless capability of the laptop so that I don't have to be glued to my table. The OS I'm using is Windows 7 Ultimate (32 bit) on an HP Compaq 6515b.I configured the modem by following the instructions in the following link url...I believe that's a straightforward method for configuring a router, and that accomplishing this is very simple.I followed the steps, only changed the username and password to that given by BSNL.Then, finally I unplugged the LAN cable and clicked on Connect to <connection name>, punched in the serial key. But it does not connect and says "Windows was unable to connect". Even after using Windows Network Troubleshooter the problem is not solved.
View 4 Replies View RelatedI recently bought an EA2700 in hopes that it will make my connection faster, stronger signal and stable. However, this is not the case. The connections keeps dropping and the range is the same as my Verizon-FiOS router. Anyway, I'm hoping that a fix be distributed to address this issue. I can't return my router to the vendor anymore.
Now, since I have two routers, I want to be able to leverage EA2700's dual-band feature and the Guest-access feature but I can't make this as a main router since my FiOS router should still be able to supply IP addresses to my cable boxes, thus, I can't configure it as a Bridge. I'm thinking if I just split the IP distribution as follows:
FiOS router: 192.168.1.2-110
EA2700: 192.168.1.111-150
I have a Linksys WRT54g router that works fine, but the signal is not very good on some points of the house.So I bought a TP-Link 740n to use as a second router. My idea is to connect both routers with a 10 meters lan cable that I have, to make the signal better on points that are distant from the main router (Linksys) or separated by walls. When job is done, will I see two different networks (one for each router) on my laptop or only the "original" signal (WRT54g)?
View 5 Replies View Relatedhow to setup WRT54G for blocking all unwanted websites for users. When tried to configure Website under Access Restrictions tba, it accepts. However it doesn't block.
View 1 Replies View RelatedHow do I configure E4200 for VOIP priority. My vonage adapter is connected to the router by Ethernet.Also I want google voice call prioritization.
View 1 Replies View RelatedI'm considering purchasing the "Cisco Linksys - E1200 Wireless-N Router with 4-Port Ethernet Switch". Before I do, however, I want to know how to configure it as a wireless bridge to my existing wireless network.I have a hardware device with only an ethernet connection (no wireless option avaialble). I want to connect the device to a wireless router / access point, in this case it would be the e1200, and then connect to my existing wireless network. The e1200 would be acting like a client of the existing network.I found this article but Step 8 is causing concern. I do not want a wired connection. The two routers must connect wirelessly.
View 8 Replies View RelatedI am following instructions I found to set up my wirelss network, but am having trouble configuring my router. I'm specifically at a standstill, because I can't connect to http://192.168.1.1. I pinged the router and got a response and went to run/ip config to confirm I have the right URL for the router, but still not able to get to the URL.
View 1 Replies View RelatedI just purchased 2 E2000 routers at BB and was assured the second one could be configured as a repeater access point. Some current messages indicate this is not possible.Will a Cisco moderator please confirm and clarify repeater options.
View 2 Replies View RelatedI have a tplink acess point TL-wa5110G . I have WISP ( wireless internet service provider). I have configured the acess point on wisp client router mode and wan type to pppoe gave the username and pwd..Now i want to share internet wirelessly. now my question is that can i connect the aces point to wan port of the wirless router to share internet wirlessly? Because i have seen the instruction figure in tplink access router where they have shown that u can connect it with with unmanage able switch to share it to wired lan.i want to ask can wirless works to share internet if i use wireless router to access point.
View 1 Replies View RelatedI have a CISCO 851W router in the garage that I want to connect to my Linksys router in the office, which is connected to the internet.The 851W is connected from it's WAN port to Lan port 1 of the Linksys router. Now, currently that ethernet cable is a straight-through cable. Does it have to be crossover? If so, I can fix that.
I want the default gateway for the CISCO router to be 192.168.2.1. I am not sure how to configure that. [URL]
We have 7200 router on which two links from different ISPs are terminated. Right now one link is primary and the second one is redundant.Now we have procured our own IPs and plan to run BGP with both the service provider. Can we configure GLBP on the router so that both the links can be simultaneously used and when one goes down the other takes the full load.
View 2 Replies View Relatedconfiguring VPN in my cisco 1721 router to connect in vpn client
I have the public IPs.
i want to configure the router for internet access for hosts this is the my pub ip x.x.x.174 and mask 255.255.255.252 this is isp given subnetmask internal ip range is x.x.x.20-x.x.x.254
View 1 Replies View RelatedI use the cisco 871 router as a firewall to my home-office. I have configured two vlans for each seperate port. That is, FE0 configured as VLAN 10 ----> connected to Layer 2 Switch, FE1 configured as VLAN 20 ----> connected to another Cisco Layer 2 Switch,FE2 not in use, FE3 not in use and FE4 is connected to WAN.I got 100Mbps speed from the ISP, but I can see that I only get 50mbps even connected to VLAN 10 or VLAN 20.Does configuring two VLANs on Cisco 871 router divides the bandwidth (to Internet) into half?
View 35 Replies View RelatedI just got Cisco 881 Ethernet Sec Router.
i would like to know how to setup this device to achieve the following:
1. Connect to my ISP
2. Do NAT on the device
3. Setup VPN to a remote site
I am having a cisco 861 series router.The Cable from the isp was connected to fastethernet4(wan port)
Following are my isp details
IP address:172.16.62.130
subnet:255.255.0.0
default gate way:172.16.62.1
dns primary:202.153.32.2
secondary:202.153.32.3
How do i configure this details in the router and access the internet in my devices.i want the network to be in 192.168.1.0 to 254.
I have a cisco 1941 ISR router and I am trying to configure a router to allow a modem for "Offband or Out of band" access.Below is the configuration on Aux port on Line (n):
line aux 0
login local
modem InOut
transport input all
speed 115200
flowcontrol hardware
I have US Robotics 56k Faxmodem which is connected to aux port of router and I am using USB dialup modem with my laptop to dailin to the router which is connected to a US Robotics Faxmodem. Then I have accessed my USB dialup modem throught HyperTerminal and I can issue all "at" commands and to dialin to the modem I have used the following command atdt914011111111 (atdt followed by country code, area code and landline number)Once I issue the above command it give me message "Connected" and after this I just get a flashing cursor. I cannot do anything nor will it display a username login prompt.
After scouring the internet for weeks I've hit a road block trying to figure this out. I've got a Netgear Prosafe FVS318N router that I am trying to enable VPN on for my office. I've read all sorts of information online about port forwarding, VPN policies, and many other things that ultimately don't tell me how to set up VPN on my specific router.Now, I've set up PPTPD on an in-house linuxbox as a makeshift VPN server and I'm successfully able to establish a VPN connection to it from a local connection (e.g. 192.168.etc. local ip address). However, when I try and VPN connect from a client outside of my office's network, I try connecting to my router's external ip address and this yields no success. My ASSUMPTION is that this has to do with a port not being properly forwarded, or something of that nature.What are the necessary steps I can take with my specific router and router firmware, which is 4.0.1-66, in order to get a VPN server up and running that listens to outside connections?
View 9 Replies View RelatedI can't seem to receive emails although I can send them and my prinet is off line. Had an IT guy come out and got me to the internet but he didn't make sure I was receing emails or able to print.
View 1 Replies View Relateddespite followin all instructions on the BEFSR41 install disc very carefully. the last stage where the router is bonfigured aborted repeatedly. What to do?
View 2 Replies View RelatedRegion : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP :
Region : India
Model : TL-MR3040
Hardware Version : V2
Firmware Version : 3.14.2 Build 120822 Rel.40902n
ISP : Reliance
Configuring my TL_Mr3040 with Huwei EC 150 model USB modem, the modem and ISP name is there in the list , I have configured all (manual/ as well as auto ) methods of authentication as mentioned in user guide.
for more infor , the exported profile from laptop where my modem works fine is
<?xml version="1.0" encoding="utf-8"?>
<utpsdoc type="Profile">
<ProfileGroup type="DialUp">
<Profile name="Reliance" type="" readonly="" device="" user="74831*****" password="74831*****" phonenumber="#777" autoapn="true" apn="" chap="true" pap="false" ip="" dns="" dnsalt="" wins="" winsalt="" imsi="" langid=""/>
</ProfileGroup>
</utpsdoc>
configuring my Cisco 2951 router. There are three routed interfaces that I need to configure: one for the internal LAN, the second for another private subnet that connects to a Data Centre and the third for the WAN connection. I have configured the Ge0/0 interface as the LAN interface with the internal network 10.17.0.0/24. I have also configured my WAN interface Ge0/1 for internet connectivity. Now, I need to configure the third interface Ge0/2 that will connect to the Data Centre. This will be a private point to point switched ethernet link. The Data Centre will host a secondary domain controlller. So, I want it to be on the same network as the internal LAN, i.e., 10.17.0.0/24. I want to be able to see all other devices that will be located at the Data Centre just like I would see all devices connected to the internal LAN.The problem I am facing is that Cisco 2951 does not allow me to configure two routed interfaces to be on the same subnet. Is there any way to work around this problem and configure both the internal LAN and the Data Centre private network to be on the same subnet.
View 6 Replies View Relatedwe have cisco 1801 router and want to configure for PPPoE.As our ISP has provided adsl connection having following settings:
Encapsulation: PPPoE
Multiplexing: LLC based
VPI = 0
VCI = 103
Login =xxxxx
Password =xxxxx
IP: dynamically from ISP
configuring cisco router 1801 for above configuration.
I'm having trouble configuring a vpn between a CISCO WRV210 and a FortiGate router.
View 1 Replies View RelatedWe are having problems configuring NAT on our Cisco 1921 Router. Below is the running config. The problem we're having is for example our FTP server 192.168.1.16, cannot be accessed from its outside IP address, which is NATed on the router. The server is verified to be up and running and when we do a show debug ip nat, we see the router is translating outside users attempting to access the ftp server to it's correct internal IP address.
View 3 Replies View RelatedI have DSL 8Mbps DL and 768kbps UL The setup look like this:Internet -> Modem -> Cisco Router -> Firewall -> Switch Core - > Multiple switches like sfe2000p? CiscoRouter: i use port gig0/1 for PPPoE and i use port gig0/2 for LAN static Router port gig0/2 with 122.54.144.153/29 connected directly to Firewall port13 with 122.54.144.154/29 ?i want 122.54.144.153/29 will my default gateway ? include no limit bandwidth,filter etc at router, Firewall will be DHCP Server and control the bandwidth, filtering etc and the client computer should get 8Mbps
Mode: Routing
Encapsulation: PPPoE
Username: xx
Password: xx
Service Name: ISP name
[code]....