I just got Cisco 881 Ethernet Sec Router.
i would like to know how to setup this device to achieve the following:
1. Connect to my ISP
2. Do NAT on the device
3. Setup VPN to a remote site
What are the commands for Configuring Cisco 1921 Route's Gigabit Port G0/0 or G0/1 for Leased Line termination having Ethernet Hands Off
Modem Provided by ISP (BSNL ) is CTR-U
Purchased a 2911 router for a customer, and I'm sure I'm missing a module here.
Teleco installed T1 and left connection to smart jack. Router only has 2-3 copper ports.
Can I get away with configuring the blackbox with RJ45 to the copper port on the router ethernet or do I need to purchase a HWIC ?
I have a CISCO 851W router in the garage that I want to connect to my Linksys router in the office, which is connected to the internet.The 851W is connected from it's WAN port to Lan port 1 of the Linksys router. Now, currently that ethernet cable is a straight-through cable. Does it have to be crossover? If so, I can fix that.
I want the default gateway for the CISCO router to be 192.168.2.1. I am not sure how to configure that. [URL]
We have 7200 router on which two links from different ISPs are terminated. Right now one link is primary and the second one is redundant.Now we have procured our own IPs and plan to run BGP with both the service provider. Can we configure GLBP on the router so that both the links can be simultaneously used and when one goes down the other takes the full load.
View 2 Replies View Relatedconfiguring VPN in my cisco 1721 router to connect in vpn client
I have the public IPs.
i want to configure the router for internet access for hosts this is the my pub ip x.x.x.174 and mask 255.255.255.252 this is isp given subnetmask internal ip range is x.x.x.20-x.x.x.254
View 1 Replies View RelatedI use the cisco 871 router as a firewall to my home-office. I have configured two vlans for each seperate port. That is, FE0 configured as VLAN 10 ----> connected to Layer 2 Switch, FE1 configured as VLAN 20 ----> connected to another Cisco Layer 2 Switch,FE2 not in use, FE3 not in use and FE4 is connected to WAN.I got 100Mbps speed from the ISP, but I can see that I only get 50mbps even connected to VLAN 10 or VLAN 20.Does configuring two VLANs on Cisco 871 router divides the bandwidth (to Internet) into half?
View 35 Replies View RelatedI am having a cisco 861 series router.The Cable from the isp was connected to fastethernet4(wan port)
Following are my isp details
IP address:172.16.62.130
subnet:255.255.0.0
default gate way:172.16.62.1
dns primary:202.153.32.2
secondary:202.153.32.3
How do i configure this details in the router and access the internet in my devices.i want the network to be in 192.168.1.0 to 254.
I need to front-end my ISP's router with another, giving me a DMZ. I have bought an EA2700 for this but I can't find how to configure it.
I plan to have the DMZ network as 10.1.2.0/24, with the ISP's router at 10.1.2.254 and the EA2700's "upstream" connection as 10.1.2.1. The internal network (where most of the clients reside) will then be 10.1.1.0/24, with the EA2700 itself at 10.1.1.254 and a DHCP range 10.1.1.100 upwards.
On the basic setup screen I've set the Internet connection type to fixed IP, 10.1.2.1; I've set its default gateway and DNS1 as the ISP's router at 10.1.2.254. Then further down in network setup I've entered the *internal* address 10.1.1.254 and set the DHCP range and netmask appropriately. I'm getting the error message "The IPv4 address and gateway are not in the same subnet mask". But the only gateway I've entered is the one by which the *EA2700* knows how to route upstream traffic, viz the ISP's router at 10.1.2.254. Or am I misunderstanding?
More fundamentally, can the EA2700 be configured in this way?
configuring my Cisco 2951 router. There are three routed interfaces that I need to configure: one for the internal LAN, the second for another private subnet that connects to a Data Centre and the third for the WAN connection. I have configured the Ge0/0 interface as the LAN interface with the internal network 10.17.0.0/24. I have also configured my WAN interface Ge0/1 for internet connectivity. Now, I need to configure the third interface Ge0/2 that will connect to the Data Centre. This will be a private point to point switched ethernet link. The Data Centre will host a secondary domain controlller. So, I want it to be on the same network as the internal LAN, i.e., 10.17.0.0/24. I want to be able to see all other devices that will be located at the Data Centre just like I would see all devices connected to the internal LAN.The problem I am facing is that Cisco 2951 does not allow me to configure two routed interfaces to be on the same subnet. Is there any way to work around this problem and configure both the internal LAN and the Data Centre private network to be on the same subnet.
View 6 Replies View Relatedwe have cisco 1801 router and want to configure for PPPoE.As our ISP has provided adsl connection having following settings:
Encapsulation: PPPoE
Multiplexing: LLC based
VPI = 0
VCI = 103
Login =xxxxx
Password =xxxxx
IP: dynamically from ISP
configuring cisco router 1801 for above configuration.
I'm having trouble configuring a vpn between a CISCO WRV210 and a FortiGate router.
View 1 Replies View RelatedI've created two configurations. One for the router side and one for the AP point side. However, I am having trouble getting the internal AP to bridge to the router properly. It is my understanding that the Wlan-GigabitEthernet is the internal interface connecting to the AP and the BVI1 together. I can't ping any ip address on the router side from the ap and the radio is active and we can see it but it seems that it doesn't give an ip address. [code] Is it a VLan issue or an ip issue but I could use a second opinion. I've included both configurations.
View 1 Replies View RelatedWe are having problems configuring NAT on our Cisco 1921 Router. Below is the running config. The problem we're having is for example our FTP server 192.168.1.16, cannot be accessed from its outside IP address, which is NATed on the router. The server is verified to be up and running and when we do a show debug ip nat, we see the router is translating outside users attempting to access the ftp server to it's correct internal IP address.
View 3 Replies View RelatedI have DSL 8Mbps DL and 768kbps UL The setup look like this:Internet -> Modem -> Cisco Router -> Firewall -> Switch Core - > Multiple switches like sfe2000p? CiscoRouter: i use port gig0/1 for PPPoE and i use port gig0/2 for LAN static Router port gig0/2 with 122.54.144.153/29 connected directly to Firewall port13 with 122.54.144.154/29 ?i want 122.54.144.153/29 will my default gateway ? include no limit bandwidth,filter etc at router, Firewall will be DHCP Server and control the bandwidth, filtering etc and the client computer should get 8Mbps
Mode: Routing
Encapsulation: PPPoE
Username: xx
Password: xx
Service Name: ISP name
[code]....
I have configured Cisco 870 router ATM interface with following configuration
interface atm 0
ip address public ip 255.255.255.254
ip nat outside
pvc 0/38
encapsulation aal5snap
no shutdown
But when I check ATM interface it is still down and line protocol is down. how to make it up and up so that internet service could be used.Also I want to know that the provider has also given username and password for internet in their device.We want to replace that device with the router and facing problems.
I had purchased a HWIC-8A in an effort to provide terminal server capabilities into multiple routers. I had found a document that I thought would take me through the configuration but it doesn't appear that the command syntax is the same on the 2911's as it is in the document. Does any know how I would need to get this configured on the 2911 router?
Here is the document I was referencing
[URL]
I know that you shouldn't update router firmware from a wireless connection. The other day, somebody told me that you shouldn't configure a router(such as changing passwords, channels, etc) from a wireless connection. I change my router settings from a wireless connection all the time.
View 1 Replies View RelatedGot road runner already get internet with wifi router, but want to set up password protection for internet access. the wifi is default now.
View 1 Replies View RelatedI only know a little about programming a CISCO router but I know the config I setup is not working...
Here is what I want to do...
The ISP provides us with IP Addresses via DHCP. Our public address is NOT static so the interface on the DSL Module needs to be provisioned to get a DHCP address with a CLASS C License.The IP address of the Router should be 10.0.0.10 subnet=255.255.255.0The LAN Clients need receive their IP address via DHCP EXCEPT for a range of 100 addresses. The lan Clients only need about 40 DHCP addresses.ONE of the Lan Clients (10.0.0.3) needs to have ports 25, 1723, and others forwarded to it.
Below is the config I am trying to use but I can't even ping the router from the LAN.
I am in the process of configuring two vpn tunnels on one interface of cisco router series 1721. Any link or document with more information?
View 5 Replies View RelatedI am configuring Remote Access IPSEC VPN in IOS Router 12.4T.I am able to establish IPSEC VPN from VPN Client 4.0. But I am able to access all the LAN machines from this client connected.I want to restrict access to only one server in my LAN rather than accessing all the servers in Datacenter.For example
-Group FTP should be able to access only FTP Server with ip addess 10.1.1.21 on Port 21
-Group WEB should be able to access only WEB Server with ip address 10.1.1.80 on Port 80
I am facing a problem when configuring the ipsec vpn on my 7200 router. [code]
View 5 Replies View RelatedI have a old server that has custom apps developed by a bankrupt company that we can't replace yet. We are being tasked with upgrading the Operating System and security patches, while preserving the existing live server. I was able to accomplish this by virtualizing it, then cloning the virtual machine. Where I got stuck was, the custom app requires a specific host name. So, I got the idea to have the two servers live on different sides of the firewall until the test platform is accepted and the old live one can be retired.
My problem is that I have no experience with configuring a real firewall like this asa5510.
Servers are:
CM1 live server
CM2 test platform
ADS Active Directory and File and Print
[code]....
I've started to carefully poke around in the Cisco ASDM-IDM, but haven't figured out how to access the DMZ from the outside (so far just testing with http as I don't have my certificate to setup https just yet). Am I missing something to get through to the DMZ from the WAN side?
I have a cisco 1941 ISR router and I am trying to configure a router to allow a modem for "Offband or Out of band" access.Below is the configuration on Aux port on Line (n):
line aux 0
login local
modem InOut
transport input all
speed 115200
flowcontrol hardware
I have US Robotics 56k Faxmodem which is connected to aux port of router and I am using USB dialup modem with my laptop to dailin to the router which is connected to a US Robotics Faxmodem. Then I have accessed my USB dialup modem throught HyperTerminal and I can issue all "at" commands and to dialin to the modem I have used the following command atdt914011111111 (atdt followed by country code, area code and landline number)Once I issue the above command it give me message "Connected" and after this I just get a flashing cursor. I cannot do anything nor will it display a username login prompt.
After scouring the internet for weeks I've hit a road block trying to figure this out. I've got a Netgear Prosafe FVS318N router that I am trying to enable VPN on for my office. I've read all sorts of information online about port forwarding, VPN policies, and many other things that ultimately don't tell me how to set up VPN on my specific router.Now, I've set up PPTPD on an in-house linuxbox as a makeshift VPN server and I'm successfully able to establish a VPN connection to it from a local connection (e.g. 192.168.etc. local ip address). However, when I try and VPN connect from a client outside of my office's network, I try connecting to my router's external ip address and this yields no success. My ASSUMPTION is that this has to do with a port not being properly forwarded, or something of that nature.What are the necessary steps I can take with my specific router and router firmware, which is 4.0.1-66, in order to get a VPN server up and running that listens to outside connections?
View 9 Replies View RelatedI can't seem to receive emails although I can send them and my prinet is off line. Had an IT guy come out and got me to the internet but he didn't make sure I was receing emails or able to print.
View 1 Replies View Relateddespite followin all instructions on the BEFSR41 install disc very carefully. the last stage where the router is bonfigured aborted repeatedly. What to do?
View 2 Replies View RelatedRegion : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP :
Region : India
Model : TL-MR3040
Hardware Version : V2
Firmware Version : 3.14.2 Build 120822 Rel.40902n
ISP : Reliance
Configuring my TL_Mr3040 with Huwei EC 150 model USB modem, the modem and ISP name is there in the list , I have configured all (manual/ as well as auto ) methods of authentication as mentioned in user guide.
for more infor , the exported profile from laptop where my modem works fine is
<?xml version="1.0" encoding="utf-8"?>
<utpsdoc type="Profile">
<ProfileGroup type="DialUp">
<Profile name="Reliance" type="" readonly="" device="" user="74831*****" password="74831*****" phonenumber="#777" autoapn="true" apn="" chap="true" pap="false" ip="" dns="" dnsalt="" wins="" winsalt="" imsi="" langid=""/>
</ProfileGroup>
</utpsdoc>
If all you have is a high end cisco router available, can you plug in hosts to the router ports, and configure them within the same subnet? (When I try to configure ports within the same subnet, I receive a "same subnet" error.
View 3 Replies View RelatedSpent a lot of time trying to configure a time warner set up. Users are using 2 SMC 8014 and one RVO42 on the network. Cannot access the internet.
View 1 Replies View RelatedI am configuring a vpn ipsec tunnel with cisco isr 2921 router and Watchguard edge 1250e. I have the watchguard configured so I just need to make sure I have everything setup on the cisco side. At this point, there is no communication as I am not sure if I configured it correctly. Should I do the crypto map on g 0/0 or dialer 1?
aaa new-model
!
!
!
!
!
!
!
aaa session-id common
!
!
no ipv6 cef
[code]......