I want to configurate Cisco SSL AnyConnect VPN on cisco router 2900 series.when i install this license on router after that can i configurate ssl anyconnect vpn? Must I be first enable EULA then install this license?
View 0 RepliesI am having two sites, at one site the ISP is terminated on 2900 Router and at one site ISP is terminated on 3500 L3 Switch. Now need to configure the IP SLA on this. In the current setup I am having two 2900 routers at one location and 3500 L3 switches which by point to point link.
View 1 Replies View RelatedI have DSL 8Mbps DL and 768kbps UL The setup look like this:Internet -> Modem -> Cisco Router -> Firewall -> Switch Core - > Multiple switches like sfe2000p? CiscoRouter: i use port gig0/1 for PPPoE and i use port gig0/2 for LAN static Router port gig0/2 with 122.54.144.153/29 connected directly to Firewall port13 with 122.54.144.154/29 ?i want 122.54.144.153/29 will my default gateway ? include no limit bandwidth,filter etc at router, Firewall will be DHCP Server and control the bandwidth, filtering etc and the client computer should get 8Mbps
Mode: Routing
Encapsulation: PPPoE
Username: xx
Password: xx
Service Name: ISP name
[code]....
I have a small issue with the AnyConnect client. Under Windows XP, I was able to accept and install the certificate from the firewall and get a vpn connection working. But under Windows 7, I have to accept the certificate everytime I conect. Is there a reason for that?
View 3 Replies View RelatedI have a small issue with the AnyConnect client. Under Windows XP, I was able to accept and install the certificate from the firewall and get a vpn connection working. But under Windows 7, I have to accept the certificate everytime I conect. Is there a reason for that?
View 2 Replies View RelatedIf there is a router ISRG2 2900 with SEC license and without HSEC license, there is a limit in count of cumulative encrypted VPN tunnels of 225. Which commands can show us a number of current tunnels on the router, so we can see if we are near this limit of 225?
View 4 Replies View RelatedWe are in the process of switching to a new internet provider in our office and have run into some problems. Our old setup was with AT&T, where they provided a managed router which linked to our internal switch and also provided NAT to the internal IP of our email server.Our new setup right now is just the internet coming in through a cable connected to a switch, we were told we needed to provide our own router. Someone donated a Cisco 2900.What should our proper set-up be? Should the internet come in directly to the router and then to our switch, or should it go to the switch they provided, then the router, and then our switch?Also, there seems to be some confusion about whether or not we need anything else to get the internet to work. There are slots for network cards in the router. Does it come with at least one built in we can use, or do we need to provide one?
View 1 Replies View RelatedI am looking to setup for BGP with the following conditions:
Client has two 2900 routers, each connecting to a seperate ISP
Client has a Sonic Firewall with a link to each router
Client owns their own /24 block of public IPs and has their own AS Number.
Client has a public /24 and /25 from the corresponding ISPs
Client has supplied the following routing rules they would like to use:
-Anything from their own public subnet should advertize via the two ISP's with best path selection
-Anything from the respective ISP public subnets should use only their link (The ISP's are not auth'd to advertize the other's network)
The two routers are directly connected to eachother and each has a link going to the Sonicwall.
what is the maximum number of Lan-to-Lan and user vpns supported in the ISR G2 2911 and 2921?
View 5 Replies View RelatedI have a customer that has a Cisco 2900 Series ISR on his Headquarters, and has some branches with RV082s.We have VPN Client configured on the 2900 ISR Router and we can connect remotely using the VPN Client to the Headquarters (192.168.1.0) however we can't reach the branches subnets (192.168.2.0, 192.168.3.0, etc.)... we found out that in the RV082 you need to specify the secure traffic as a destination, but in only supports one network (192.168.1.0 or Headquarters in this case), we can't specify the VPN Client pool defined on the ISR so it can reach the incoming VPN Clients.Is there any way to accomplish this? We need to access the branches subnets when connecting using VPN to the 2900 ISR.
View 1 Replies View RelatedMy work laptop uses a Cisco AnyConnect VPN Client (Software Version 2.5.2006). The connection protocol is DTLS.I recently upgraded to a Cisco RV180 at home at it is running the latest software version (1.0.1.9).
Since the RV180 went into service the work laptop will connect intermittantly. Usually email works but web browsing and and other services do not. It is slight strange behaviour- and seems to defy what a VPN should do......
The behaviour is very repeatable. For example from the customers office the laptop connects perfectly via VPN and if I swap back to an older inferior make of router at home VPN also works normal without changes to the laptop configuration.
I work for a large company (70,000+ employees) and we use "standard" builds so altering the laptop configuration is not really an option.
It seems to me that the RV180 doesn't support the DLTS VPN connection (indeed DLTS passthrough isn't an option in the VPN passthrough list) and is possibly blocking some incoming packets on the WAN interface.
I haven't yet tried a firewall rule to allow a DLTS (or UDP perhaps?) connection back in from the WAN side (obviously from just the IPs at my work end) but this is the only option I can think of to make this machine connect "correctly".
I recently bought a Cisco SRP527W and I'm trying to setup a second wireless network for guests.
I created a "guest" VLAN and I assigned the "guest" SSID which I have created.
I created a "guest" DHCP server and assigned it to the "guest" VLAN.
The "guest" SSID is set to broadcast and has WPA2 Personal (TKIP+AES) authentication. These are exactly the same settings I have for the "non-guest" WiFi.
However, I can't get my clients to connect to the network. The "guest" WiFi is visible and clients are prompted to enter the password but after that they end up with an APIPA address. When I move the "guest" SSID to VLAN1 (along with all the other networks) then it works absolutely fine.
I was just wondering if I'm simply missing something in the configuration ..
The device is running the latest firmware (1.01.24 (003) September 7, 2011)
DHCP server has DNS Proxy setting enabled and WAN Interface configured as "Default Route" (have basically replicated the same settings as VLAN1)
I'm trying to configure and DMVPN architecture with two routers ASR1006 to server a bank remote offices, one ASR in CO building and the other in CA building (CO: Operational Center; CA: Recovery Center).Each ASR have two LAN connections to internal network and two WAN links to remote office. Each WAN links belongs to differents provider.Each remote office has a router with two WAN links connected to that WAN providers.We are configuring the DMVPN considering two primary tunnels in the CO building and two failover tunnels in CA building.We made the configuration (schemas and configuration attached) but we only get two tunnels up at a time. We cannot ping from office router to four tunnels interfaces in both hubs.
We made some test disabling some tunnels and we could get communication only with two tunnels interfaces. We got communication through tunnels when we have just two.We want to have the four tunnels for high availability. We would like to know how to troubleshoot and make a design review because the examples and documentations are very limited.
i got a problem in configuring a VPN Connection for our Colleagues (Laptops & Iphones 4/4S/5) We got an RV042G .
A WAN Connection from Deutsche Telekom AG with Static IP connected in WAN1. Configured for PPPoE. Ive got configured a Port Forwarding on our SBS 2011 Server for OWA and other Services on web. I´ve got extreme Problems configuring VPN Connections. We use Quick VPN, other tools got to much buttons to click .
1st i configured a Group VPN , with FQDN (Remote Group) Local Group (IP only) . i configured 2 users. Then on a Laptop connected to the internet through an Hotspot Connection of an Iphone.
I entered the WAN IP .. Username. Password. Pressed ENTER. I get to the point of Verifyiing Network, and after it timeout with Remote Gateway not responding. Do you want to wait. If i Press Yes, after max. 1 minute there comes the message again.
I looked in the VPN Summary, and i see, that my username was connected through VPN for seconds, but then disconnected. Do i have overseen an option to configure??
I just purchase the Cisco Router RVS4000 vpn and I am having problem configuring the VPN option. I just try all way I could imaging, but somehow something are missing and I don't know what it is. Here are a image of my current configuration.
No matter the change on my configuration, the status always in down.
Will the RV042 work with theAnyConnect Secure Mobility Client app? If so, is there and app note available? If not, which routers wil work with this app?
View 5 Replies View RelatedI'm trying to ensure I have wireless coverage in my entire house and having extreme difficulty getting all machines to play nicelyWireless modem router #1 (downstairs in my house) is connected to the ADSL line and has the following config:IP Address = 192.168.1.1 DHCP on DHCP pool 192.168.1.3-192.168.1.100 Subnet = 255.255.255.0 Wifi channel = 1 Wireless router #2 (upstairs) is connected by ethernet cable to Wireless modem router #1 and has the following config:IP Address = 192.168.1.2 DHCP off Subnet = 255.255.255.0 Wifi channel = 11 Different SSID and encryption key to Wireless modem router #1 With this configuration, I can connect to the internet via both routers and all seems to be well. Except... having established a connection through either one, my machines will only make a pretend connection with the other one. By "pretend", I mean that the (Windows) machine says it has an excellent connection to the router but can only see machines on the LAN - it cannot get to the internet even though other machines are connected through the same router to the internet.
For example, if I'm sitting next to the downstairs router and establish a connection with it, all is well. Then I move upstairs and my machine switches to the upstairs router. Signal strength will be reported as "Excellent" and I'll be able to connect to the local NAS or printer but no external devices or sites.I have tried having the same SSID and wireless configuration on both but the result was the same.Today I read the suggestion to enable the DHCP server on the 2nd router but to set it to distribute a different non-overlapping IP range (i.e. router 1 can have a pool of 192.168.1.3-192.168.1.50, and router 2 can have a pool of 192.168.1.51-192.168.1.99)
I'm having trouble getting my RV220W router to work with a DSL modem. I pre-configured the device and shipped it to one of our store locations. I came to find out that the site had an "Advanced" modem (according to the carrier) and I had to have them "bridge" the modem. Prior to having the modem "bridged" I was able to have the user plug the RV220W into the modem, and the computer that was hard-wired to the router was pulling the correct set of IP addresses, however, my VPN tunnel was not working because the WAN address that the RV220W was receiving was 192.168.2.12 instead of the staticly assigned IP address from the ISP After bridging the modem, the user is able to access the RV220W but he does not have internet connectivity. According to the carrier, this is because we need to enter their PPOE username and password into the RV220W. My only problem is that my on-site person is not very technical, and although I have access to one of our other sites with a working RV220W I'm not able to find where I enter this PPPOE information into the device. get this thing setup so that the customer is able to get connected to the internet, and that my RV220W is pulling the correct staticly assigned IP address from the ISP?
View 5 Replies View Relatedgetting a SF300 to properly route IP between 2 VLANs. I've watched the demo video and performed everything it showed, but I get the most bizarre half-way results. I haven't done anything on Cisco routers in about 15 years, so I'm a little rusty.
We have an office LAN with a cable modem/router for Internet access where the modem/router has IP address 192.168.1.1. We have the usual 24 bit prefix net mask. The SF 300 is connected to this network on port 1.
I have configured port 1 to VLAN 1, interface in Access mode, assigned a static IP address of 192.168.1.36, which is a free address on our office LAN. I have configured port 2 to VLAN 2, interface in Access mode, assigned a static IP address of 192.168.3.1 I put a static route in the modem/router, pointing 192.168.3.0/24 to 192.168.1.36.
I have a PC on 192.168.3.10 attached to port 2.
The SF300 can ping 192.168.3.1, but not 192.168.3.10. 192.168.3.10 can ping 192.168.3.1. It can also ping 192.168.1.1, and can pull up an HTTP router admin page from 192.168.1.1. 192.168.3.1 can be pinged from anywhere on 192.168.1.x, but 192.168.3.10 cannot be pinged from 192.168.1.x. Finally, 192.168.3.10 cannot ping any other addresses on 192.168.1.x except 192.168.1.1, and cannot reach the Internet.
Here's my configuration:
switch6d919d#show runconfig-file-headerswitch6d919dv1.3.0.59 / R750_NIK_1_3_647_260CLI v1.0set system mode router
file SSD indicator encrypted@ssd-control-startssd configssd file passphrase control
[Code].....
I have an issue with configuring the VPN Stateful failover between two cisco routers 3845. The stateful HA is not up.
Below is the topology
Configuration on HA-1
interface GigabitEthernet0/0
ip address 194.170.9.183 255.255.255.240
ip accounting output-packets
duplex auto
speed auto
[code]....
We have an MPLS network to a half dozen remote sites. At our main location we have a 2800 series router. In the routers config are the following lines for QOS. When I go to the routers on the other end of the MPLS, none of them are configured with these same policies. Would these not be in the running config of the 1800 series routers, or is this not setup correct and this should be removed?
View 13 Replies View RelatedI have a RV042 with two ADSL services on it, that is a nice simple thing for this unit. The problem that I am having though is that one of the ADSL services also has a /29 attached to it.
How do you go about configuring this additional sub net? On a previous unit I have had to create IP aliases, and could then port forward and NAT without too many issues, but it doesn't appear that the RV unit seems to work the same way.
I want to set up a WiFi internet connection for a campus. I plan to use 4 routers. the first one is directly connected to the internet. I want to share internet access wirelessly with the other routers. Each of the routers should be a hotspot for each of the four blocks in the campus.
View 1 Replies View RelatedI'm trying to troubleshoot a wireless network at an Inn which is shared among three buildings. The internet at the main building works fine.
However there is a WDS set up for the other two houses that are part of the property. The network is a bit of a mess IMO. The main problem is that routers on the end of the WDS chain work for awhile after booting, but frequently stop issuing IPs. When a device tries to connect it says unable to configure IP or something like that. Rebooting the router always fixes the problem.
My networking knowledge is very limited but I think some settings must be incorrect. I will try to described the setup here..
All of the following routers are WRT54G's with DDWRT
Main router: 192.168.1.1 [different SSID that WDS], all routers forward DHCP to this router
WDS router 192.168.1.3 at main building is connected to an cantenna that shoots the signal over to 1st house. Gateway & Local DNS set to 192.168.1.1
WDS router 192.168.1.4 at that house is the main AP for that house and gets its signal from 1.3's cantenna. Gateway & Local DNS set to 192.168.1.3
WDS router 192.168.1.5 under the deck at the 1st house picks up that signal from 1.4 and uses a cantenna to send it to the 2nd house. Gateway & Local DNS set to 192.168.1.4
WDS router 192.167.1.6 under the deck of the 2nd house gets the signal from 1.5's cantenna. Gateway & Local DNS set to 192.168.1.5
The IP configuration problems happen at the 2nd house with 192.168.1.6. I believe 1.5 also has IP configuration problems but that router is not used other than to transmit to 1.6. Again rebooting the router fixes the issues temporarily. It works for a couple days up to a couple weeks before the IP problems start.
Mac addresses for the WDS are set of course. I have been trying to experiment with settings for awhile, but do not really know what I am doing. I am not the one who set this up.
Also under the Advanced Routing tab,here are the Static Routing settings:
192.168.1.3: Destination LAN NET: 192.168.1.0, Gateway: 192.168.1.1
192.168.1.4: Destination LAN NET: 192.168.1.3, Gateway: 192.168.1.1
192.168.1.5: Destination LAN NET: 192.168.1.4, Gateway: 192.168.1.3
192.168.1.6: Destination LAN NET: 192.168.1.5, Gateway: 192.168.1.4
Update: looks like STP should be enabled for WDS? Going to try enabling that I guess.
I have a problem configuring port forwarding to 443 and having client VPN to work.When 443 is NOT forwarded, VPN just runs fine (QuickVPN).As soon as I enable 443, the VPN stops working. No client can connect.I have the latest 1.2.0.9 firmware.Is there a way to enable 443 and having VPN to work at the same time ? I need 443 for Exchange.
View 4 Replies View RelatedI'm tryng to configure a vpn with a cisco small business pro router, model srp527W-k9-g5 But when i try to set the “remote ip” in Remote traffic selection a I have to set (10.0.0.0) a message said:
“Invalid IP Address Format”
If i change the ip and i put 10.0.0.1 i have not error but I have to put 10.0.0.0 and if i configure it on a cisco WRV210 (por example) i have no error.
I bought a RV042G router some days ago to manage 2 adsl lines at my home. Everything works correctly except one thing : i can't configure the bandwidth management. When i go to "Bandwidth Management" menu, then "Bandwidth Management Type" then i choose rate control or priority and i a had some rules to priorize http protocol for example, then i click on save button. After a few seconds of internet usage i loss connectivity to the router and internet and 192.168.1.1 became unreachable to ping. I had to unplung the power cord to restart the router, the same problem still occurs until i remove all the rules ! Some times i even had to do a factory reset because my adsl modems are unreachable behind the router (unable to ping the gateway).
View 4 Replies View RelatedIf you have two wireless routers on the same private network. On configuring the second router's password and SSID I know the second wireless routers DHCP must be turned off.Can you explain step by step on configuring the second wireless. Must the second wireless be connected to the internet. If yes, how? Must I take the first wireless router off the modem and connect it to the second wireless router for internet connection. (Problem with that is connection from the ISP)
View 2 Replies View RelatedI have a 6 month old RV042 with the newest firmware (v4.2.1.02). Over the weekend I configured the DMZ which after a lot of trial and error, was able to get working. Prior to configuring DMZ, I was able to log in with remote management. However now remote management no longer works. I've tried:
- Rebooting the router
- Turning the firewall off/on
- Turning remote management off/on
- Changing the remote management port
The only step I haven't taken is resetting the router back to factory defaults and trying to reconfigure it all again. This router is so finicky I have no faith I'd be able to get my current functionality back again.
I am trying to configure an older Belkin Router (Model Number 5FD8230-4) as an Access Point so that I can boost the range of my network. The problem I have is in configuring the old router. It won't allow me to change any settings, or at least the changes don't stick, even after clicking "apply changes". I tried creating an administrative password but I am not even sure that this is working. I am using a Macbook, so perhaps this is an Apple compatibility issue. I have tried resetting the router and reverting to Factory default settings, but no joy.
View 3 Replies View RelatedI am following instructions I found to set up my wirelss network, but am having trouble configuring my router. I'm specifically at a standstill, because I can't connect to http://192.168.1.1. I pinged the router and got a response and went to run/ip config to confirm I have the right URL for the router, but still not able to get to the URL.
View 1 Replies View RelatedRegion : UnitedStates
Model : TL-WR841ND
Hardware Version : V8
Firmware Version :
ISP : optimum online
I have two wireless routers:
TP Link TL-WR841ND
and
TP Link TL-WR541G
I would like to:
use the TL-WR541G for my children wireless laptop, wireless ipad and wireless iphones.
I can turn this unit off at a specific time each evening as I wish.
The WR841ND is used for my wireless laptop, wired iMac, wired Roku stream player and wired Voip adapter.
I tried a few things but really do not know what I am doing and I cannot get both wireless routers to access the internet.
What I tried so far:
Cable modem ethernet out to the input on the WR841ND router. took one of the four hardwire outputs from the WR841ND and ran into the input on the WR541G I powered on the cable modem....it booted... i then powered each router up and waited for each to boot. I launched web browser and navigated to : http://192.168.0.1/ this allowed me to setup the WR841ND router.
it's current settings:
Firmware Version: 3.13.27 Build 121101 Rel.38183n
Hardware Version: WR841N v8 00000000
WAN type: dynamic IP
LAN IP address: 192.168.0.1
subnet mask: 255.255.255.0
DHCP Server: enabled
Start IP: 192.168.0.100
End IP: 192.168.0.199
How do I set up the second router? I tried to disable the DHCP server on router 2 (WR541g) and change the IP but don't know what to change it to.
I am looking for a Cisco document that gives me the,IP through-put on 2901, 2911 and 2921 routers with Policy based routing applied.,IOS version 15.1.3TOther processes, EIGRP Stub, VLAN routing, SRST,MGCP gateway (analog and PRI).
View 1 Replies View Related