Restricting Internet Access To Particular Users On XP?
May 28, 2011
got myself the Netgear internal PCI wifi adapter today & it works just fine on my Windows XP SP3 desktop.
The only problem I have is the question of restricting complete internet access to kids @ home. If it was an external USB adapter, I could have just taken it away but the concern is the device being an internal & always available one.
The user configuration on the PC is such that there is 1 main administrator (The actual windows "administrator" account) that no one uses. Apart from that,
- 1 user with admin privileges (me)
- 1 limited account for the kid
- 1 admin privilege account for the kid again (for purposes like installation of games which require an admin account as mandatory)
I would like for the wifi PCI card to work only when I login to my user account. There must be someway by which I could disable the device or make the internet inaccessible in the other accounts,, (but pls bear that 1 of the account that the kid uses also has admin privilege)
I tried disabling the device from control panel but in vain.. (tried something like the sys admins do in corporates ..) disabling the usb ports on the PC's in my office..!
View 4 Replies
ADVERTISEMENT
Feb 20, 2013
I am a networking student so have access to a free copy of Windows Server 2012. I want to setup and get experience with AD, DHCP, and DNS, among other services. Right now I have a Netgear router attached to a Cisco switch. (studying for CCENT cert) I have my desktop and server plugged into switch. I want my desktop to connect to the domain for testing and messing aroudn with. My wife has a netboook, smartphone, and wireless ipod. I'd like her 3 devices to get an IP from the DHCP server without having her authenticate to the server. Will the Netgear router allow this since wirless access is on? Or will she need to authenticate with the server to get a DHCP IP? I am gonig to disable the router's DHCP service.
View 3 Replies
View Related
Mar 20, 2011
The following diagram represents my current network.
I would like for the Phone and the Laptop both on wireless to have internet access but not access to the other PCs/shares.
I have access to routing tables in both the cable router 10.0.0.1 and the wireless router
wired : ASUS RX3042H
wireless : Linksys WRT54G (default Firmware)
View 2 Replies
View Related
Jan 13, 2011
Not sure If I am asking this correct. I want to install a wireless access point into a switch and out the WAN. Going to PW access into the wireless access point. Can I restrict the user from entering the LAN from wireless access point? Change subnets, what to do? Would not mind resticting speed, etc. I think I can through my switch.
View 19 Replies
View Related
Oct 9, 2012
I have installed a video security system into my home/office and several IP cameras are connected via my wired cat5 network which connects to my router and switcher into a PC with internet access. This will allow me to record any break ins and alert me of this event and view it in real time.I would like to restrict access to these devices for anyone else on the network, with either dedicated access or password protection.
View 1 Replies
View Related
Dec 4, 2012
I am trying to block access to facebook and twitter on my router, to a certain range of ips, 192.168.1.8 - 254. I have been digging around and trying stuff but all I do seems to restrict everyone access to the internet.
View 5 Replies
View Related
Mar 3, 2011
We have recently ordered a laptop along with a docking station with the intention of connecting it with the desktop PC in the office. We want the documents folders of both computers to be synchronized and to that end we want to share the folders between each computer. However, to do so we will have to connect the laptop to the larger network in our office. Given the sensitive nature of the documents we only want the desktop PC and the laptop to be able to access these files and synchronize them.
Is there anyway in Windows 7 to specify exactly which computers are allowed access to shared folders on a computer? What's the best way to achieve the file synchronization between the two?
View 2 Replies
View Related
Jan 12, 2013
This is my scenario. I have my IP as 172.16.1.1 (aaaa.bbbb.cccc.dddd) which has full internet access. Now when i am not available in the office, i noticed some one assigning my IP in to his workstation and gaining full internet access. How do i restrict such things? i.e. even if some one assigning my IP on the network, they shouldnt access LAN or WAN.I tried 'arp 172.16.1.1 aaaa.bbbb.cccc.dddd arpa' configuring on my L3 Cisco 3750X switch assuming i can acheive, but that did not work.
View 8 Replies
View Related
Oct 29, 2012
I have Configured a WLAN with WiSM2 Controller installed on a 6500 series, Aironet 3600series APs and ACS 5.3 for userauthentication. The ACS is connected to Active directory so users are authenticating using the AD (802.1x is used and not a pre-shared key) on SSID A. I have created a separate SSID B for guest users. I have put restrictions on this SSID. Guest users are also created on the same AD where internal users are created. How can I force Guest users to connect to SSID B and not be able to connect to SSID A? Currently they can connect to both.
View 3 Replies
View Related
Nov 6, 2012
I have an ASA firewall and I have never configured an FTP server for a large scale network (well large in my opinion). I want to ensure we have the highest level of security available for the FTP and to limit only the specific users designated by an ACL. Would SFTP be the best available option for security measures? Should I only use Passive FTP and what range of ports above 1023 should I open for only 1 or 2 FTP clients at a time? Also if I use Passive mode do I need to use protocol inspection for FTP?Also, Currently I'm unsure of what files need to be accessed on our network but should the SFTP Server always only be installed within the DMZ?
View 4 Replies
View Related
Apr 19, 2011
I have a Cisco 2901 Terminal server with AAA authentication via ACS server. I create twoaccounts on the acs server, cciesec2011 and vendor. Both accounts can log into the Cisco 2901 Terminal Server without any issues. By the way, I am NOT using AAA authorization on the Cisco Terminal Server. Once cciesec2011 or vendor accounts are authenticated, theseaccounts can access all the async line on the Cisco Terminal Server.
Now I have a new requirements. I would like to allow cciesec2011, once this account is successfully authenticated, this account has access to ALL async line on the Terminal Server. The "vendor" account, I want to restrict this account access only to async line 35 (there are 32 async lines available on the Cisco Terminal Server) and nothing else.
How can I accomplish without using AAA authorization on the Cisco Terminal Server?Is it possible to use "privlege level" to accomplish this? if so, how?
View 5 Replies
View Related
May 28, 2011
got myself the Netgear internal PCI wifi adapter today & it works just fine on my Windows XP SP3 desktop.
The only problem I have is the question of restricting access to kids @ home. If it was an external USB adapter, I could have just taken it away but the concern is the device being an internal & always available one. The user configuration on the PC is such that there is 1 main administrator (The actual windows "administrator" account) that no one uses. Apart from that,
- 1 user with admin privileges (me)
- 1 limited account for the kid
- 1 admin privilege account for the kid again (for purposes like installation of games which require an admin account as mandatory)
I would like for the wifi PCI card to work only when I login to my account. There must be someway by which I could disable the device or make the internet inaccesible in the other accounts,, (but pls bear that 1 of the account that the kid uses also has admin privilege)
I tried disabling the device from control panel but in vain.. (tried something like the sys admins do in corporates ..) disabling the usb ports on the PC's in my office..!
View 14 Replies
View Related
May 29, 2012
I have a neighbor, whom I barely know, (don't know his name even) ask if I would be willing to give him the number off of my modem so he can cannot wireless to my internet. I believe that is a bad idea. For one I don't know him but if it was possible and I did that, would he be able to access my account? or start more trouble? He at first said If I give him the numbers off of my router but then I stopped him because I have a modem not a router. So I would never let him but was curious if someone can tap into a signal of mine from a laptop next door to me using wireless signal? And if so can that person see all of my stuff? Would my computer and I be at risk?
View 5 Replies
View Related
May 27, 2011
Is there a way to restrict wireless access to my router from wireless pc's in my home. Two grandsons are off from school now, and are playing online games to the wee hours of the morning. Can I do something to have the routher shut off their connection at a certain time? Is that possible. If I have to go back to dd-wrt to do that, fine. I have lynksis wrt54g with their 4.2.1 firmware.
View 5 Replies
View Related
Jan 10, 2012
restricting access to internet for roughly 20 users. Right now we are connected using broadbandand using dhcp as assigned by common switch. All pc's are in a common workgroup. recommend me the hardware / software required to restrict this access.
1. Will I require a router as well as a switch ? or should I simply get a new switch ( for more then 20 users ) This would mean static ip for all users.
2. My idea is to create a AD server and use websense on it so that users who require internet access can still open internet sites but will be restricted through websense proxy.
View 1 Replies
View Related
Feb 24, 2012
First I tried restricting all computers from accessing the internet from 11:00PM to 6:00 through access control. I enabled it and set up the schedule but it does not cut off the internet. I went through create a new schedule and did that but again it still connects. Then, in access control, I selected always and put in my son's IP address and created a schedule for him but it won't allow him any internet access.
View 2 Replies
View Related
Feb 9, 2012
The goal is to add a 2801 router between a DSL modem and a switch and obviously still access the internet. I connected and configured as explained below and the results are:
- I am able to ping internet addresses from the 2801 router
- I am not able to ping internet addresses from userlaptop but I am able to ping LAN gateway (192.168.254.254)
I cannot understand why the internet requests from the user laptopuser are not routed to the internet but the router itself can access the internet.
INTERNET====DSLmodem=====CISCO2801=====unmanagedSwitch=====userlaptop
DSLmodem:
non-bridged mode and does the PPPOe authentication.
WAN interface: Dynamic IP address assigned by ISP
[Code].....
View 14 Replies
View Related
Feb 28, 2013
I have configured and tested an ASA-5505 that will be deployed at a customer's home. The ISP cable modem will connect to the E0 (outside) interface of the ASA. All other interfaces on the ASA are configured for the inside network 192.168.5.0/24. I have created a VPN site-to-site tunnel between this ASA and the UC540 to allow 192.168.5.0/24 subnet access to the internal networks on the UC540.
The user has requested that all the network devices used by the rest of the family will only need to connect to the Internet. They will not need access to the VPN tunnel and they will not need access to the computers on the 192.168.5.0/24 inside network. I was planning on performing the following tasks to get this to work.
View 2 Replies
View Related
Jan 21, 2013
I'm currently undergoing CCNa academy so I got a "job" from my boss to configure Cisco 871 router. Unfortunately we just finished first semester at academy so there are some things that I'm still having hard time to understand. I managed to configure router so it connect to internet or to be exact it has internet access through another adsl modem that is in bridge mode. url...The problem is that users are not able to use internet when connected to this router. I'm able to access router through telnet ( ip 192.168.13.10) but that's it.192.168.13.0 255.255.255.128 is network that we use at work. 192.168.13.5 is IP address that is assigned to zyxel adsl modem ( If I'm correct, we could have used any address here since we are connecting this directly to router ? ) Zyxel adsl modem is connected to FA4 port on Cisco router. LAN cable is connected to FA0 port and from there it goes to switch ( it's some asus switch with 50 ports). [code]
If I ping google dns from router e.g. ping 8.8.8.8 it works. If I ping url... it doesn't work. Also I'm able to access router via 192.168.13.10 but if I use router as default gateway then I'm not able to access the internet.
View 8 Replies
View Related
Mar 19, 2013
We have a Cisco 3750 stack connecting to the MPLS router, able to ping 8.8.8.8 - [URL], the internal users on their own Vlan can ping the default gateway the 3750 switch but no further, trace route from the PC/Servers stops at the 3750 stack.We have the switch configured to ip route 0.0.0.0 0.0.0.0 to the public interface in the MPLS router, from the switch I'm able to ping the internet.
View 17 Replies
View Related
May 16, 2012
I am able to successfully connect to my ASA5505 via AnyConnect via a mobile device. Upon doing so, I lose internet connectivity. My access list appear to be correct to I'm sort of at a loss.
[code]....
View 6 Replies
View Related
Oct 4, 2012
We have an ethernet port on Cisco router 1800 connected to the ADSL modem. The router does ip nat translation, but users complained it is slow when they access to internet. [code]
View 1 Replies
View Related
Mar 24, 2013
I have a WRT54G routher hardlined to a Ubuntu 12.04 server that is dedicated to minecraft.I have two ports opened for Minecraft to run off of.I'de like to give remote access to the computer to other people to maintain the server.BUT I need to restrict ANY and ALL ability for them to access the internet by either blocking all other ports or something else. Id rather not have to restrict it through Ubuntu if I don't have to.
View 1 Replies
View Related
Apr 4, 2012
How does one configure the router so that Internet users can access internal company websites? The only thing that appears is the Cisco router login. Also I need to configure Terminal Services and its not on the list under Service.
View 2 Replies
View Related
Sep 22, 2011
We are running ACS 5.2 patch 6 and want to restrict access for users to be able to add devices to the system.For example, admin person in site A can only add devices into the site A group and cannot see/access other sites groups.
View 1 Replies
View Related
Feb 26, 2013
I have some problem with the ASA 5510 ver 7.0(6). My manager wants to keep this as backup. tried lots of things but still users not able to access internet nor can i ping anywhere.For example when i ping 4.2.2.2 i dont get any reply.The runing config is below for ur ref :
HQ-ASA-01# show running-config
: Saved
:
[Code]......
View 9 Replies
View Related
Feb 24, 2011
I have a normal setup of ASA5505 (without security license) connected behind an internet router. From the ASA5505 console I can ping the Internet. However, users behind the Firewall on the internal LAN, cannot ping the Internet even though NATing is configured. The users can ping the Inside interface of the Firewall so there is no internal reachability problem. In addition, I noticed that the NAT inside access list is not having any hit counts at all when users are trying to reach the internet.
When i replace the ASA5505 with a router with NAT overload configuration on it, the setup works normally and users are able to browse the internet.
The ASA5505 configuration is shown below.
hostname Firewall
interface Ethernet0/0
description Connected To Internet Router
switchport access vlan 10
[Code].....
View 2 Replies
View Related
Nov 1, 2011
Based on my diagram, my computer A (192.168.100.11) can ping and access my computer B (192.168.10.14). But, when i'm home and i use remote access vpn (192.168.200.x) in cisco asa 5520 to connect to my computer A is okay. But, when i try to ping my computer B is not okay. I already do the exemption for 192.168.100.x and 192.168.10.x in nat rules for inside interface (192.168.100.2) ...
Should i put routing from outside 1.1.1.2 to 192.168.10.x by using 192.168.100.1 as a gateway?
View 1 Replies
View Related
Oct 19, 2011
I have a STORCENTER IX2-200 CLOUD EDITION in my office with 3 machines hooked up via the router. I cant seem to access users when I enable the security. If i disable security i can get in. This is happening on Windows XP and 7. I've tried Iomega support and it all has to be done via email which is annoying.If i enable security I get the following windows error: \iomegakate is not accessible. you miht not have permission to use this network resource. access is denied.all the machines are logged on as administrator. I did fix this problem although only for a few hours after speaking to Iomega. They advised to use the Net Use command and delete all connections. Ive forgotten what it was now as they remote accessed in.
View 1 Replies
View Related
Dec 21, 2012
I want to create a website but only allow a certain user or group of users access to that website. Assuming that user or users will be from the same location, and likely the same static IP, can I throw a firewall between my internet connection and web server and only allow that specific IP address access to my web server by a rule?If there is a better way to handle that,
View 3 Replies
View Related
Apr 1, 2012
I currently set up two LAN networks. But one of them (Router 2) will be open (no password). Will this create a security compromise? Can the Router 2 Users access information of users of Router 1?
Modem WAN > Router 1 WAN
Router 1 LAN > Router 2 WAN
The router 1 and 2 are broadcasting different networks and SSID.Is there any setting that I need to change, or this configuration is perfectly safe? both of them have DHCP enabled.
View 3 Replies
View Related
Mar 18, 2011
I have a customer with an ASA5510. We have an SSL VPN (tunnel-based, or "SVC") that we use for remote access. That works great.They want to be able to use this same functionality, but add users who will not have the full access that the current SSL VPN users have. So in other words we currently have a small group of users who get full access to the LAN. Then they want to have a second group of users who will only have access to certain nodes.I'm wondering if there's some way to do this using LDAP between the firewall and the Radius server? The user gets put in a different tunnel group depending on what the FW learns from the server?We only have the Anyconnect Essentials license, so unfortunately we can't do a clientless SSL VPN, which otherwise might work well here.
View 3 Replies
View Related
Aug 12, 2011
can i print as am joint to a domain.
View 2 Replies
View Related
