Not sure If I am asking this correct. I want to install a wireless access point into a switch and out the WAN. Going to PW access into the wireless access point. Can I restrict the user from entering the LAN from wireless access point? Change subnets, what to do? Would not mind resticting speed, etc. I think I can through my switch.
View 19 RepliesIs there a way to restrict wireless access to my router from wireless pc's in my home. Two grandsons are off from school now, and are playing online games to the wee hours of the morning. Can I do something to have the routher shut off their connection at a certain time? Is that possible. If I have to go back to dd-wrt to do that, fine. I have lynksis wrt54g with their 4.2.1 firmware.
View 5 Replies View RelatedThe following diagram represents my current network.
I would like for the Phone and the Laptop both on wireless to have internet access but not access to the other PCs/shares.
I have access to routing tables in both the cable router 10.0.0.1 and the wireless router
wired : ASUS RX3042H
wireless : Linksys WRT54G (default Firmware)
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedI have installed a video security system into my home/office and several IP cameras are connected via my wired cat5 network which connects to my router and switcher into a PC with internet access. This will allow me to record any break ins and alert me of this event and view it in real time.I would like to restrict access to these devices for anyone else on the network, with either dedicated access or password protection.
View 1 Replies View Relatedgot myself the Netgear internal PCI wifi adapter today & it works just fine on my Windows XP SP3 desktop.
The only problem I have is the question of restricting complete internet access to kids @ home. If it was an external USB adapter, I could have just taken it away but the concern is the device being an internal & always available one.
The user configuration on the PC is such that there is 1 main administrator (The actual windows "administrator" account) that no one uses. Apart from that,
- 1 user with admin privileges (me)
- 1 limited account for the kid
- 1 admin privilege account for the kid again (for purposes like installation of games which require an admin account as mandatory)
I would like for the wifi PCI card to work only when I login to my user account. There must be someway by which I could disable the device or make the internet inaccessible in the other accounts,, (but pls bear that 1 of the account that the kid uses also has admin privilege)
I tried disabling the device from control panel but in vain.. (tried something like the sys admins do in corporates ..) disabling the usb ports on the PC's in my office..!
I am trying to block access to facebook and twitter on my router, to a certain range of ips, 192.168.1.8 - 254. I have been digging around and trying stuff but all I do seems to restrict everyone access to the internet.
View 5 Replies View RelatedWe have recently ordered a laptop along with a docking station with the intention of connecting it with the desktop PC in the office. We want the documents folders of both computers to be synchronized and to that end we want to share the folders between each computer. However, to do so we will have to connect the laptop to the larger network in our office. Given the sensitive nature of the documents we only want the desktop PC and the laptop to be able to access these files and synchronize them.
Is there anyway in Windows 7 to specify exactly which computers are allowed access to shared folders on a computer? What's the best way to achieve the file synchronization between the two?
This is my scenario. I have my IP as 172.16.1.1 (aaaa.bbbb.cccc.dddd) which has full internet access. Now when i am not available in the office, i noticed some one assigning my IP in to his workstation and gaining full internet access. How do i restrict such things? i.e. even if some one assigning my IP on the network, they shouldnt access LAN or WAN.I tried 'arp 172.16.1.1 aaaa.bbbb.cccc.dddd arpa' configuring on my L3 Cisco 3750X switch assuming i can acheive, but that did not work.
View 8 Replies View RelatedI have Configured a WLAN with WiSM2 Controller installed on a 6500 series, Aironet 3600series APs and ACS 5.3 for userauthentication. The ACS is connected to Active directory so users are authenticating using the AD (802.1x is used and not a pre-shared key) on SSID A. I have created a separate SSID B for guest users. I have put restrictions on this SSID. Guest users are also created on the same AD where internal users are created. How can I force Guest users to connect to SSID B and not be able to connect to SSID A? Currently they can connect to both.
View 3 Replies View RelatedI have an ASA firewall and I have never configured an FTP server for a large scale network (well large in my opinion). I want to ensure we have the highest level of security available for the FTP and to limit only the specific users designated by an ACL. Would SFTP be the best available option for security measures? Should I only use Passive FTP and what range of ports above 1023 should I open for only 1 or 2 FTP clients at a time? Also if I use Passive mode do I need to use protocol inspection for FTP?Also, Currently I'm unsure of what files need to be accessed on our network but should the SFTP Server always only be installed within the DMZ?
View 4 Replies View RelatedI have a Cisco 2901 Terminal server with AAA authentication via ACS server. I create twoaccounts on the acs server, cciesec2011 and vendor. Both accounts can log into the Cisco 2901 Terminal Server without any issues. By the way, I am NOT using AAA authorization on the Cisco Terminal Server. Once cciesec2011 or vendor accounts are authenticated, theseaccounts can access all the async line on the Cisco Terminal Server.
Now I have a new requirements. I would like to allow cciesec2011, once this account is successfully authenticated, this account has access to ALL async line on the Terminal Server. The "vendor" account, I want to restrict this account access only to async line 35 (there are 32 async lines available on the Cisco Terminal Server) and nothing else.
How can I accomplish without using AAA authorization on the Cisco Terminal Server?Is it possible to use "privlege level" to accomplish this? if so, how?
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
We are running ACS 5.2 patch 6 and want to restrict access for users to be able to add devices to the system.For example, admin person in site A can only add devices into the site A group and cannot see/access other sites groups.
View 1 Replies View RelatedWhat I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedI have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedI have a neighbor, whom I barely know, (don't know his name even) ask if I would be willing to give him the number off of my modem so he can cannot wireless to my internet. I believe that is a bad idea. For one I don't know him but if it was possible and I did that, would he be able to access my account? or start more trouble? He at first said If I give him the numbers off of my router but then I stopped him because I have a modem not a router. So I would never let him but was curious if someone can tap into a signal of mine from a laptop next door to me using wireless signal? And if so can that person see all of my stuff? Would my computer and I be at risk?
View 5 Replies View RelatedI have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
I have a 5500 controller that we use to manage our lightweight access-points. We have had complaints that the 'guest' vlan in the boardroom is not usable. Our guest vlan is in fact overloaded.
I went back to the original site survey and noticed that coverage for the room is not ideal so I would like to have a new lightweight access-point installed in the boardroom and somehow limit the access to it to only a few people.
I am currently running a guest wireless network using 4404 controllers on the wireless side and a 4402 as an anchor controller, all running 7.0.98.0 and all is working fine. Accounts being created via the WCS lobby admin and applied to the 4402.The question I have is, is there any way of restricting the use of an account to 1 device at a time. I am currently seeing evidence of password sharing and my boss would like to make sure that everyone who use the system has their own credentials.
View 1 Replies View RelatedI have a WRT54G routher hardlined to a Ubuntu 12.04 server that is dedicated to minecraft.I have two ports opened for Minecraft to run off of.I'de like to give remote access to the computer to other people to maintain the server.BUT I need to restrict ANY and ALL ability for them to access the internet by either blocking all other ports or something else. Id rather not have to restrict it through Ubuntu if I don't have to.
View 1 Replies View Relatedhave netgear pcmcia card need to connect to new belkin wireless access point.
View 1 Replies View Related