WRT150N Wireless Router Won't Allow To See Rest Of Network
Sep 19, 2011
My boss has a WRT150N that he wants to add to our network. The line coming into this router comes from a switch which all of our other computers/ printer are connected to. The router transmits the internet fine, but I cannot access the LAN when connecting through the router. The printer has a static IP. All internet traffic comes through a hardware firewall which is between the outside world and the switch. When I connect the line going into the router straight into a computer, the computer can see the network/print/whatnot fine.
View 4 Replies
ADVERTISEMENT
Mar 10, 2013
I am currently connecting my PC to a mobile phone as a Wireless Access Point to give that PC access the internet. I also have a small home network, with one other PC and a Game Console. I own a Linksys E900 Wireless-N300 Router. My problem is this. How do I share that internet connection with the rest of the home network?To the best of my knowledge its not possible to connect my mobile phone directly to my Linksys E900 Wireless-N300 Router.
So my alternative idea is to connect to the internet via one PC, set up that internet connection as "Shared." and then allow the other devices on the home network to connect thru this. My question is how do I set up my Linksys E900 Wireless-N300 Router to allow my other PC and game console connect to the internet? Bridge Mode? PPPoE?
View 1 Replies
View Related
Jun 13, 2011
I'm having problems with my wireless computers seeing the rest of my network. This is my setup. ATT dsl modem into a 16 port netgear gigabit switch into dlink 615 Some computers are hardwired two are wireless All was working well before d-link with the linksys When im on a wireless computer i cant see the other computers hardwired to the network through the switch. When i take a wireless computer and plug it directly into the switch it see the rest of the computers fine.Something screwy is happening between the switch and the dlink router not allowing me to see my shared folders and printer over wifi.
View 1 Replies
View Related
Jun 30, 2011
We have the Linksys WRT150N router. A while ago it suddenly lost the name we gave it when we set it up and now it shows up as Linksys. Also, it is no longer secure, and sometimes we can't even see our network - it isn't even listed. How do I go in and change this? Will I have to reset the wireless information on my printer, etc?
View 4 Replies
View Related
May 23, 2013
I am new to configuring WLC's. Our small business (5-15 wireless devices + 15ish wired) is trying to use a hand-me-down WLC and AP for our office wifi. We have a WLC 2106 directly connected to a 1231G-A-K9 via the WLC's port 8 POE. I am aware Cisco does not recommend this method, but we do not have a configurable switch at our disposal. We do not need separate VLAN's therefore I have left everything untagged. The AP has a static IP setup to allow communication to the WLC since it did not pull one from the WLC.
The AP is getting the correct network information and is showing up on the WLC monitoring page. I am able to connect to the new wireless network and able to ping between devices connected to the same AP. Now here is my question/issue. I cannot get communication from the WLC/AP to the rest of our network via an unconfigurable Netgear switch (FS605v3). After connecting an open switch port from the Netgear switch to port 4 on the WLC, I am lost. I tried giving port 4 on the WLC an address on the office network, but I receive an error stating "the IP information conflicts with another device".
Here is what I have setup on WLC
Virtual - 1.1.1.1
MNG IP-192.168.10.10
AP MNG Ip- 192.168.10.11
Subnet - /24
Gateway - 192.168.10.1
DHCP - 192.168.10.250
DNS - 192.168.10.250
Static Address on the AP's fa0-192.168.10.15
Attempted port 4 setup on WLC
VLAN identifier 0
IP- 192.168.10.25
Mask - /24
Gateway - 192.168.10.1
Port - 4
Our office network setup:
Subnet - /24
Gateway-192.168.10.1
DHCP - 192.168.10.250
DNS - 192.168.10.250
View 1 Replies
View Related
Jul 4, 2011
I have two notebooks, one smartphone, and one blu-ray player that connects to my wireless network. My gaming PC is hard wired into the same router that broadcasts my wireless network. About 5-6 times, my wireless network will drop and everyone connected to it wirelessly will lose their connection for about 1-2 minutes. While my gaming PCs internet connection is undisturbed, all of my wireless devices can no longer "see" the network SSID and therefore connect to it. The problem has been happening consistently for many months.
View 1 Replies
View Related
Sep 5, 2011
I have 12 wap4410n to enable wireless connection to a school building with 3 floor. I planned to configure one as a Access point. My doubt is in which AP mode i have to configure the rest as WDS Bridge or WDS Repeater other mode. In each access point i have Ethernet connection to the switch.
View 1 Replies
View Related
May 10, 2011
I had a power outage and reset modem and wireless router(linksys WRT150N) I can connect to internet when I use ethernet cable but when I go wireless I sometimes can't see wireless network, sometimes I can see network but it wants WEP password even though security is disables and other times it connects no problem. It happens on both a MAC and a PC.
View 1 Replies
View Related
Oct 11, 2011
Whenever I connect to my router via wireless, It slows the network to a crawl, and I can't view websites through the same PC.Now, It only started a few days ago, and I can't find the root cause. This happens in Windows 7, however, it works in Linux with the same PC, in the same location, so it can't be the wireless card going bad. When the computer isn't online, however, everyone other connection, including smartphones, my wife's laptop, PS3, all work. I've tried updating the drivers, flushing the dns, resetting the winsock, ip release/renew, haven't found anything that works.
I've also run numerous virus scans, malware, spyware, and registry scans. The only thing I can think of is something is trying to send a lot of traffic to the router. So far, Malware Bytes, Avast, AVG, and Spybot haven't picked up anything, and I can't find the traffic leak via Windows Firewall or Comodo.
OS: Windows 7 Home Premium
Wireless Card: Asus USB-N13 using Ralink drivers
The only thing I haven't tried is connecting through my ethernet card, but it's not feasible at the moment to move the desktop to the router.
View 14 Replies
View Related
Apr 27, 2012
My home network is up to now all hard-wired, nothing shared etc.I just got an ipad though, so do want to have wireless available now. I would like the ipad wireless router to be isolated so that the desktops run no risk from getting a virus via the ipad wireless connection.So, I was going to buy another router - would I be able to plug that into the wired router, and the desktop also plugged into the wired router, would that keep every part of the network isolated from the others?
View 8 Replies
View Related
Apr 21, 2011
Limit his bandwidth. but he will only be staying till the end of summer. The new roomie then might be a torrent monkey.Completely shield my other computers from his sight, so to speak. Like I said he's not a hacker but the new roomie might be.
I'd like the router (linksys WRT54G v3 runner latest linksys fw) and the rest of my network (main PC and media server) to be resistant to at least a script kiddie, and hopefully against a intermediate hacker.I'm currently using wifi with WAP2 personal as the router security.
View 8 Replies
View Related
Aug 4, 2010
Can the Nexus 7000 provide NTP to the rest of my network? Can it be an NTP server? I have the followign ntp configuration on it, and have used the commit command, but it seems to be ignoring any NTP requests from other devices. [code]
View 8 Replies
View Related
Nov 26, 2007
I'm trying to setup Xbox live for my Xbox 360. I have the WRT150N wireless router and just got the wireless adapter that plugs into the 360. It said the adapter couldnt pick up the signal then i realized i needed to enter the WPA key from my wireless router. I checked the information on the router and it only gives me the serial number and MAC address. How I can find out what the WPA key is for the router??
View 5 Replies
View Related
Aug 8, 2012
I have a wrt150N that I am trying to determine whether it's dead or not. I cannot connect to it directly, even if I plug my laptop directly into the Router. Pressing the Reset button does nothing, the lights don't even flash?If I change my Ethernet cable it does represent which port I'm using but I can't ping 192.168.1.1 either? I want to try and flash the bios but A: there's no file to download for this model and B: I presume I need to be able to connect in order to do the flash?
View 4 Replies
View Related
May 13, 2011
I am currently at a friends house attempting to fix a situation he is having with his' wireless router, it is a Linksys WRT150n.Connection to the internet is possible via ethernet connectivity, however wireless is another story, devices can see the network but cannot connect to it, i have disabled the security key from the network to see if it was a simple password incorrection but still no dice.The current basic wireless settings have network mode set to mixed, and radio band, wide and standard channels set to auto, all other settings in the advanced tab are set to their default values.
View 1 Replies
View Related
Jan 23, 2008
I have the wireless-n wrt150n router. I have it wired to my computer and have it wirelessly connected to my ps3. But for some reason there is another unnamed device listed under My Network. My network was not secure before, but I changed it to secure when I noticed the unnamed device. How do I remove that unnamed device from my network?
View 3 Replies
View Related
Nov 24, 2007
Laptop keeps disconnecting from WRT150N
View 9 Replies
View Related
Sep 1, 2012
I want to replace a WRT150N with an E2500 and retain the setup/settings of the WRT150N.
View 2 Replies
View Related
Sep 7, 2012
Up until about midnight tonight, my router, which has been plugged in to my cable modem, has been working fine for years, both wired and wirelessly. Suddenly, however, I went to log on to my desktop PC (wired connection; Windows 7), and I had no network connection. ipconfig indicated "media disconnected." My cable-based phone service (VOIP) is still working fine at this time.
First attempt - unplug router, wait 15 seconds, plug it back in. Still no good, though my network sharing center indicated that the network connection was appearing/disappearing every few seconds, never actually getting "internet" connectivity.
Second attempt - attempted to use a WIFI-based device (iPad), which could not see my home network by name at all.
Third attempt - reset both the cable modem and the router, bringing the cable modem up FIRST. Same results as the first attempt.
Fourth attempt - plug the wired PC directly into the cable modem - this worked fine and is how I am submitting this post as I type. So the cable modem is working properly.
Fifth attempt - look up the information on how to reset the router to factory defaults. Used a paperclip to depress the reset button for 10- and on a subsequent attempt, 30-seconds (no obvious "reset" blink pattern was observed). Plug PC back in to router. PC would not obtain any DHCP-based IP address and the network sharing center was still behaving as in the first attempt.
Sixth attempt - disconnect the cable modem uplink and see if I could get the local network functioning. Now I noticed that the LED patterns on the router were behaving as:
- Power and my PC's slot number lit
- All lights lit
- All lights off
- Power and my PC's slot number lit
- etc
View 2 Replies
View Related
Aug 6, 2011
In my home I have a cable modem wired to a links wireless router a wrt 300n in my office (only hardwired used in there) and I do not get such good distance to my back bedrooms with my laptop. I have run a Ethernet cable dead center of the house for my sat receiver that is connected and wired to the 300wrt. Here is my question can I use the 150 like a hub or switch at the office connected to the cable modem and use the wrt300n router so that I get wireless on that side of the house. Or in reading here I see I can maybe use a bridge. I do have a older Linksys wrt150n sitting in a box.I have read until my eyes are almost bleeding and am not sure. How I can get a better signal on the other side of the house.
View 4 Replies
View Related
Jan 6, 2012
Changing the NAT Type to open because I can't play with some of my friends on Playstation.
View 1 Replies
View Related
Dec 31, 2011
chaning the NAT Type to open because I can't play with some of my friends on Playstation.
View 2 Replies
View Related
Nov 9, 2012
I can get regarding using the Collobos Fingerprint software through my WRT150N router. I'm using Windows XP SP3 and immediatly after installing (which went extreamy well) it immediatly found and listed all of my home network printers. All of the wired and wireless windows based systems in my house can see and print to the printers without any problem. However, getting ANY of my apple devices (iPad, iPhone etc ) to print will not even show them as listed on the device when I select print on the devices. Collobos says that I have to make sure that Ports UDP 5353 doe Bonjour and TCP 6361 for FingerPrint need to be open both ways for it to work, I have no problem getting into the router settings and have set them up as stated above in Port Range Triggering and enabled. Also made sure Filter Multicast was not check marked in Security. Unfortunatly, that doesn't seem to work as I had hoped.
View 3 Replies
View Related
Aug 21, 2011
I have a router that I upgraded the firmware a while ago, I stopped using it several months ago, I was going to give this router to my sister, i tried a hard reset(30 seconds press reset, unplug, hold hold the reset, wait 20 sec, plug power, hold for 30 sec and release the reset) and I tried to login with admin admin and it doesn't accept it. I tried with another router dlink 614i and the same problem, after resetting it it's not accepting admin admin log/pass.
View 1 Replies
View Related
Apr 3, 2011
I am using a WRT150N with firmware v1.00.5. I have a Linux setup with Squid connected to the network with the gateway 192.168.23.254. The WRT150N has a gateway of 192.168.23.1. The WRT150N is also connected to an Apple Base Station which serves as the Access Point for WiFi users.Squid limits access for IP addresses listed under the .254 gateway. But once I change my gateway to 23.1, everything is accessible. I want to block sites as well on the WRT150N. But every time I try to put a new Access Restriction, it doesn't work.
View 4 Replies
View Related
Jul 28, 2012
It has happen suddenly : Internet is not working through WRT150N, though it work when directly connected to the modem. So I think it is a router issue :On the WRT150N, Internet light is flashing fast for 2 seconds, then is off for 2 seconds, then flashes, then is off and so on, wether there is a device (computer, modem, ...) plugged or not, through the blue ethernet connector.And sometimes, Internet light stays off from power on, whatever is done with ethernet connexions (yellow or blue).
When connected to the blue ethernet Internet connector, my pc ethernet lights don't blink (nor the link light or the data light)I have try the 30-30-30 reset cycle. But it doesn't improve.I have tried the loopback test : connect an ethernet cable from the one of yellow ethernet port of WRT150N to the blue ethernet of WRT150 N.Sometimes, the light for the yellow ethernet port goes on for a few seconds, while the Internet light continues to flash. After a few seconds, both go off.Sometimes, as soon as the loopback is made, the 2 lights go off, and if a computer is plugged to the yellow port, the ethernet lights of the computer and the router stays off.But I can access to WRT150N through Wifi and I can access to the web management.
View 7 Replies
View Related
Oct 31, 2012
Several "consultants" have told me that the problem probably lies within my Linksys WRT150N.However, upon pinging the router, it responds. I did not reset the router to factory default), I just pinged it, and it's there.My firmware is v1.0.04. My provider is Cox Communication, and the connection os cable modem.Curiously, my wife's I-Pad will not open these links either.Sample link that doesn't work: url... Upon website opening click on "weekly ad".
View 2 Replies
View Related
Feb 9, 2008
I had successfully set up my new WRT150N router and it was working. But then it just stopped after about 12 hours. All the lights on the front of the router are blinking. When I directly connect to the router, my computer can't detect it. I've browsed through these forums a bit and tried a few things - the reset button (60 seconds), unplugging the router, downloading the EasyLink Connect tool, but I'm still stuck.
View 5 Replies
View Related
Jul 10, 2011
I've been using a WRT150N wireless router successfully up until a couple days ago, when it stopped being detected. I can plug my computer directly to my modem, and it works, so my internet connection is fine. I have an older BEFW11S4 router that I am using currently, but it is very slow compared the the N router. I've tried resetting the 150N router, and also the modem, and combinations of both, but nothing seems to work. I plugged the router into my computer without connecting the modem, but I'm not able to access 192.168.1.1 either. All the lights illuminate when the router is plugged in.
View 9 Replies
View Related
Jan 21, 2008
I purchased a WRT150N in early Dec 07. I had a number of problems with the unit disconnecting from wired and wireless connections erratically anywhere from 1/2 hr to 10 hrs. of operation. Troubleshoot thru Linksys chat. Ended up replacing router. Now I am having the same problem with replacement router. I've updated my windows XP, SP2, updated Ethernet driver and manually reconfigured router per Linksys advise. Wife and my laptops have N adapters, primary PC is wired in. It seems to disconnect all connections at same time, totally random. The only way to reconnect is to power down router for a few seconds and then power up.
View 9 Replies
View Related
May 23, 2009
My Linksys WRT150N recently gave up on me and started to give me weird issues and started to disconnect (all the ports including wired & wireless) anywhere from 3 to infinite number of times per day and my only solution was to remove the power chord and connect it. I tried all possible ways possible including resetting the router, stopping SSID broadcast, removing the encryption, etc, but non worked. As the router was out of warranty my only option was to take it to the dealers where they told me it would take 3 weeks to fix and God knows how much they would have charged me. But after flashing the firmware with the dd-wrt it has been almost 24 hours without a single problem and now I have the cool option of seeing who is connected to the router, etc. This is a MUST for every Linksys owner.
1. Reset the router using 30-30-30 and waited for 2 minutes for things to come back 2 normal
2. Flashed the router with "dd-wrt.v24_mini_generic.bin"
3. Reset again using 30-30-30 and wait again4. Flashed the router with " dd-wrt.v24_std_generic.bin"5.
View 3 Replies
View Related
Jan 28, 2012
I have WRT150N, with firmware version 1.01.9 and I can not get the internet access policy to work.Here are my settings: PC list is configured through IP range as follows:Even if I deny internet access completely, I can still access the internet.
View 2 Replies
View Related
Feb 25, 2013
For the last 4 years I’ve been using the Linksys Router, model WRT150N V. 1.1 and never had any problems—until now.Yesterday I noticed that my wireless devices (i.e., two computers, tablet and Internet radio) either don’t work at all (the Internet radio) or the pages load extremely slowly—for example, the tablet has become, for all intents and purposes, unusable. Since my ‘main’ computer is connected directly to my cable internet, I know that there is nothing wrong with the Internet connection itself, only with wireless connection.I disconnected the Linksys Router for 2 minutes and reconnected it, but to no avail. I know that I have not made any changes to any software/hardware that might affect the speed.Since I also happen to have access to another wireless Internet connection (a different provider), I connected to that network and all my wireless devices were working perfectly. Therefore, I think the problem must be with the router. I am using Windows XP (on the main computer, where the router and Internet cable are attached).
View 5 Replies
View Related
