Windows 7 - Hosting Multiple Domains?

Feb 21, 2011

Is it possible for Windows 7 to host multiple domains? I have seen that it is available for plenty of other OSs and I am sure that it is. I just wanted to make sure.

View 2 Replies


ADVERTISEMENT

Join Multiple Domains In Windows Xp?

Oct 27, 2011

join multiple domains in windows xp?

View 2 Replies View Related

Home Network :: Hosting Multiple Websites On Server?

Jan 8, 2012

I had setup 2 servers at home. I'm now in need of hosting 4 websites. I have 4 static public ip's. I'm currently using a router with DD-WRT firmware installed. I have setup up as static NAT. X.X.X.27 to 192.168.0.100, X.X.X.28 to 192.168.0.101. This is my current setup for the existing 2 webservers which host a website each. I notice apache allows for multiple websites per server. One of the server's is a dell 2500 with 2 NIC's and will not be a problem assigning two ip's. The second server only has 1 NIC. Should I buy another NIC card for the second server or could I get by using a virtual NIC? The load on the servers isnt heavy. Only bout 20 clients connect to them daily.

View 8 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.3 Multiple AD Domains

Aug 9, 2012

I do have a quick question about Cisco ACS 5.3 and multi domain authentication. How is it exactly handled?
 
Can I join more than one domain with the ACS server? Or do I still need to configure that bidirectional trust relationship between those AD forests (even with the ACS 5.3)?

View 5 Replies View Related

Cisco Firewall :: 6509 / Setup Multiple DMZs For Hosting Servers?

Aug 19, 2011

I would like to setup multiple DMZs for our hosting servers.  Currently there is a single DMZ in which our reverse proxy servers are connected using a public IP address.  The idea is to have the reverse proxy forward the request from the Internet to the hosting servers in another DMZ.  The purpose of the hosting DMZ is to protect it from the outside as well as from the inside.  There will also be a development DMZ where we can test content prior to going live with the website.
 
Network:   We currently have two Cisco 6509's (Core) with a FWSM in each running active/stanby configuration.  There is a 10Gb Fiber connection between each Cisco switch to two Cisco 4948s (Top of Rack Switches).  I can either setup OSPF or Trunking between the core and top of rack switches.  The Cisco 4948s will support VLAN 7 (hosting DMZ 10.0.7.0/24) and VLAN 8 (development DMZ 10.0.8.0/24).  Each webserver is connected to both Cisco 4948 for redundancy.
 
Question:   If I have a single interface connecting both VLANs 7 and 8, either through Layer 2 or 3, then how can pass both DMZ traffic to the appropriate servers?  The reason why the servers are in the same rack connected to the same two switches is that we are using Blade Servers and VMWare.

View 3 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.x - Configuring Multiple AD Domains For Authentication

Jan 7, 2013

Currently on ACS 5.2 and our MS Active Directory is migrating to a completely new domain. There will be a two way trust between them for the 24 month migration period. How best to configure ACS connect to both domains?

View 2 Replies View Related

Cisco Wireless :: WLC 2500 Authentication Using Multiple AS Domains?

Mar 13, 2012

The  users belong to Multiple AD domains. If we purchase WLC 2500 controller. Can I  have one more WLANs authenticate to multiple radius or ad domains? I thought one WLAN/ ssid authenticate to single radius server.

View 4 Replies View Related

Cisco AAA/Identity/Nac :: Can ACS 5.2 Support Multiple Active Directory Domains For 802.1x

May 25, 2011

I'm looking to implement ACS 5.2 using 802.1X, we have two seperate AD domains.A single switch will need to support both ADs, so if a machine in AD1 is connected, it will be authenticated to the ACS using AD1 and applied to VLAN1, while a machine that is in AD2 will be authenticated to AD2 and applied to VLAN 2.
 
I'm looking at machine authentication, not user authentication, so I assume that I will need to import two certs from each AD.

View 3 Replies View Related

Cisco Switching/Routing :: Multiple VPC Domains On A Single Nexus 7000?

Nov 13, 2011

I have a customer with three rooms where teh access layer aggregation switches are run back to.
 
Access Switch Stack A -> room 1 + room 2
Access Switch Stack B -> room 2 + room 3
 
Is it possible to have three Nexus 7000s ie one in each room (1,2 and 3) and have them setup like this:
 
Nexus 7000#1     vPC domain 1
Nexus 7000#2     vPC domain 1 + vPC domain 2
Nexus 7000#3     vPC domain 2
 
Thus gving all access switch stacks redundant links to the core withouit spanning tree.
 
I know its not ideal but its a campus site and thats how the existing fibre runs go.

View 5 Replies View Related

Best Web Hosting For Vpn?

Nov 25, 2012

What is the best hosting for vpn. I'm thinking bluehost, but is there anything better/cheaper. I prioritize the features: reliable, features (ftp, ssh, phpbb, perforce, etc.)

View 1 Replies View Related

Explaining The Intranet Hosting For 150 Workstations

Mar 29, 2011

You are appointed as a system administrator for a large company which has its own computer intranet hosting 150 workstations and around the same number of users. Write few points explaining the roles you would expect to take on as part of your new employment in terms.

View 2 Replies View Related

Hosting Online Games On Wifi?

Feb 28, 2012

I am playing Hidden Stroke online and i can join games but i cant host, when i create a game my IPV4 address shows up instead of my IP address which means no one can see the game. I am a guest PC on my home Wifi.PS i have already opened all the ports that the game requires to play.

View 5 Replies View Related

NIC Stops Working When Hosting A Server?

Mar 23, 2011

On Windows XP, my integrated NIC stops working after hosting a server. The server starts fine, ports are forwarded, firewall is down, modem is fine, but when I receive a connection, it shows they have made a connection, but then they drop, as do I. I can't browse or ping anywhere. I have to physically disconnect, then reconnect the ethernet cable to the port, or restart the computer. Upon ipconfig, the adapter is set with the Windows default ip (169.x.x.x) and cannot be /release'd or /renew'd.

View 10 Replies View Related

Internet Speed For Hosting Servers?

Aug 23, 2011

So 3 days from now im getting comcast cable....12 mbps download and 3mbps upload (something like that)I want to know if I can host servers in online games such as... modern warfare 2 and black ops...pretty much any popular first person shooter. I noticed that every game I play I am not host and I am lagging...my current connection is 2.5 MBPS download and 0.4 MBPS upload.

View 9 Replies View Related

Forwarding Ports And Hosting Minecraft Server

Apr 30, 2013

I recently signed up with AT&T U-Verse. They required that I buy a 2Wire 3600 HGV router. I looked up how to forward ports -- and even called an AT&T representative -- and I am sure that I forwarded them correctly. I'm trying to host a Minecraft Server. I forwarded port 25565 in TCP and in UDP. After that wouldn't work, the AT&T representative said that the traffic was being blocked from my side. I then checked my Windows Firewall and allowed all proper applications -- Minecraft and Minecraft Server. When that wouldn't work, I went in an manually added exceptions to Windows Firewall for TCP - 25565 and UDP - 25565 Inbound and the same for Outbound. Nothing.I have tried to check the ports in DMZ mode with Windows Firewall disabled -- they are still timing out. What should I do?

View 7 Replies View Related

Cisco WAN :: Using Cat6500 For A Small Hosting Company

Jan 9, 2012

I am running a smaller hosting company and i am currently looking at a Cat6506 switch with a SUP720 Supervisor Engine. I have also been looking at a Cat6509 with a SUP2-GE Supervisor Engine. At the moment i am getting my connection from a ISP but i am going to get my own BGP AS now.. My question is just, how much will the SUP720 be able to route, and how many routes will i need to get it to route my packets in and out of my AS? I have seen that the full BGP table is over 400,000 and the SUP720 is only capable of 256,000, but do i really need the full table? I
 
major differences between the SUP720 and SUP2-GE Supervisor Engines?

View 7 Replies View Related

Hosting Website On Network - Doesn't Resolve Locally?

Dec 12, 2011

I am setting up a webserver to host our website on our local network. When I'm browsing from an external network, I can pull our website example.com and a sub domain test.example.com. However, when I'm browsing from our internal network, I cannot pull up test.example.com. I am not sure if this is due to propigation issues or what.When I do nslookup from external, it shows my network's main IP address. When I do it from local, it can't find an address and says non-existent domain.Should I have any problems connecting to my website if it is using my external IP address? Will this be a loopback problem? If so, how can I resolve this?

View 3 Replies View Related

Hosting Private Server With DLink 2740b Router?

Dec 24, 2011

a few days ago i had a router dlink 2740b and i made a dedicated server of call of duty4 where my friends and i played. yesterday i changed my router with another dlink 2740b f1 version (a new version of the same router): i make port forwarding for the cod4 server but the server doesn't go online....i see it only in local....but my friends and i don't see it in the internet server in the game menù...

View 1 Replies View Related

Cisco :: 3200 - How Much RAM Required On Server Hosting Works

Aug 7, 2011

how much RAM is requied on server hosting CiscoWorks. Our CiscoWorks is running like snail. We have 3200 logical devices configured on it. Specially browing different pages of CiscoWorks is very very slow.
 
how big hard drive will be enough for CiscoWorks with below applications installaed and configured with 3200 devices.. Currently we have 65GB Harddrive and its 85% full.
 
Server Platform: Windows 2003 server 32-bit
Server RAM: 4GB
Hard Drive: 63GB-CiscoWorks is installed on this Harddrive.
Another Partition of Harddrive is 130GB and its 100% free.
 
LMS: 3.2.1
RME: 4.3.1
CM:5.2.1

View 2 Replies View Related

Cisco :: Cat6506E / Netflow In A Dual-homed Hosting Environment

Jul 12, 2011

We're trying to set up netflow based billing for our hosting environment.  We're dual homed to two different ISPs using BGP peering with each (ASN 18817).  The drawing below shows the logical setup:  The routers are each Cat6506E with Sup32 and PFC3B/MFSC2A running 12.2(33)SXJ.  The direct link between is layer 3 (routed ports) for iBGP peering.  The dark line is a layer 2 LAN made up of multiple switches (not shown) each connected to both 6500's with spanning-tree for loop protection.  These switches also provide a layer-2 path between routers but the configured BGP peering is set to the layer-3 port IP on the link.  There is at least one firewall connected directly to a 6500.  The firewalls are all ASAs connected to any one of the not-shown mid-span switches.  The router interfaces to the layer-2 LAN is a VLAN SVI using GLBP to provde a redundant gateway.  There are multiple subnets on this vlan configured as secondary IP addresses on the VLAN interface (and in the GLBP gateway configs).
 
The question is:  how do we collect stats from all traffic to/from the internet without collecting any local traffic (firewall to firewall) and without getting duplicate flows sent to our collector? 
 
I was hoping to just put "ip flow ingress" and "ip flow egress" on the ISP facing L3 ports but that's not actually collecting outgoing flows (appears egress netflow may not be supported on the 6500).  I added "ip flow ingress" to the VLAN interface but that didn't seem to fix it so I also addes the global command "ip flow ingress layer2-switched vlan 50".  However after a small change to the layer2 LAN some (but not all) of our clients saw a near doubling of bandwidth (according to netflow).  We compared the netflow stats to the server port usage stats for one client and it looks like we were under reporting before the change and appear to be over-reporting now.  I'm thinking the overage is either because we're counting MLS traffic flowing between subnets on the layer-2 LAN but can't verify.  With GLBP moving the default gateway and MSTP blocking at least one uplink from a mid-span switch to a 6500, traffic flows can be difficult to predict.  Especially when you don't know exactly when a flow gets accounted.  For instance, if a packet comes into one 6500 becase that's the only layer-2 path to the gateway BUT the gateway is currently on the other 6500, does the first 6500 count that flow or does the second one count it or will both?  etc etc.

View 1 Replies View Related

Multiple LAN Cards On Windows XP?

Mar 1, 2012

I have 4 computers with 3 LAN cards (1 onboard + 2 PCI) installed on each of the machines. One of the machines run Windows Server 2008 and other 3 run Windows XP. I am trying to simulate routing on these desktops. I have connected all the machines in a mesh topology. Please refer to the image attached. I am able to ping all the 3 machines from the server machine. However when I try to ping the machines from the client PC running XP, it is able to ping only one machine connected to it. All the network cards on the client machine running XP show that they are connected (in control Panel-> network connections). But ping packet shows only one host is reachable. The other two network cards(that are not able to ping other machines) are showing red light. I am not able to get over this.

View 8 Replies View Related

Multiple NIC Segregation In Windows?

Jul 11, 2012

I'm in a shop that requires our workstations to have two NICs. One attaches to a router and through to a DCHP internet connection. The other is a static IP via crossover to our instrumentation system. The issue is that these systems can be extremely remote and rely on satellite or 3G Network connections and are not overly reliable. Every time our net connection drops, BOTH NICs reset, causing us data loss from our instrumentation. Any way to separate the connections so that if one drops, the other is left unmolested?

View 5 Replies View Related

Establishing Communication Between Two Different Domains?

Oct 17, 2012

My company bought another company and moved them into our building. the company moved in but are on an entirely different network all together. wired separately, different domains.what i would like to do is be able to have them communicate with each other. have users on company A be able to use printers on company B's side of the network.

View 15 Replies View Related

Can't See Multiple Work-groups In Windows 7

Oct 24, 2011

As we all know, MS has changed the default workgroup names in different versions of windows. Additionally, you can rename your workgroup anything you like. I have XP, Vista, and Win7 computers, a television, BluRay player, a Wii, two printers, and a NAS with two USB drives attached. All of these -except the Win7- are wired to one of two switches. I have wireless: iPad, the Win7 notebook, Nintendo DSs. I have friend, and non-friend machines (computers, tablets, and phones) that come and go that are wired or wireless. The 3 windows computers all have the same workgroup name. All of my other units do not use workgroup names. I have a router, and two unmanaged switches, and have, on occasion, a second router. The main router, which has wired, and dual band wireless (each with two named wireless networks) nets, sees everything, by name and/or MAC address. Win7 is blind, deaf, and dumb.: it shows its own workgroup name, but no other workgroup name(s) , and, consequently, no unit on these other workgroups. It will show some wired units not in a workgroups - the television, and the printers (not the Wii or NAS). It will not show the wired XP computer! No wireless units either in workgroups or not in workgroups appear. Additionally, Win7 only shows units on its wireless network, not on the other three. The wired units it does show are not on any of the wireless networks, though it lists them on its wireless network.I have left the Homegroup, and terminated the Homegroup services. I have allowed discovery, and unlimited sharing of everything on every computer on the router, and yet the Win7 unit does not share or see well at all.Why?

View 2 Replies View Related

Multiple Networks Different Subnets Windows 7?

Jan 24, 2013

I have a Windows 7 Pro Desktop with an on-board Ethernet and an Axis USB To Ethernet adapter. The on board Ethernet is configured as dhcp and obtain the address 10.162.146.123 with 255.255.255.0 subnet. The Axis USB to Ethernet adapter is static ip configuration with 10.38.25.37 and 255.0.0.0 as subnet. Under the adv settings I have also another ip 11.38.25.37 with 255.0.0.0 subnet. When the Axis is communicating 10.38.0.1 network I can not access the internet using the on board Ethernet 10.162.146.123. I have to disable either one of the cards to access one network at a time.

View 3 Replies View Related

Servers :: How To Setup Trusts Between Two Domains

May 19, 2011

Need step by step instructions for setting up trust between two domains

View 1 Replies View Related

Network Setup How Many Domains People Have

Dec 22, 2012

I am creating a migration plan for our organization, Im wondering, how many domain controllers people have, how many member servers and what there used for?

View 3 Replies View Related

How To Block Specific Domains In Sonicwall

Apr 5, 2011

How do I block specific domains (pandora.com, etc.) in the Sonicwall? It seems like this would happen in the CFS but do I need a subscription for this? I don't want to subscribe to Sonicwall's filtering list, I just want to block a couple specific domains.

View 9 Replies View Related

Sharing Outlook Calendars Over 2 Domains?

Apr 4, 2012

My company have just set up a new subsidiary. I have had a request from my Managing Director asking if it is possible for us to share calendars with the other company so if he wants to make a meeting appointment he can check if Joe Bloggs from the subsidiary is free.There is domain A (parent company) and domain B (subsidiary)Both us and the subsidiary are currently running Microsoft Exchange 2007 on windows SBS 2008 server with mainly windows 7 clients with Outlook 2007-2010?Is it possible to share calendars between the 2 domains?

View 7 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.2 AD Trust To Other Domains?

Jan 27, 2011

We are trying to set up ACS 5.2 in our multi-forest AD environment.  As part of our evaluation we set up an Active Directory External Identity Store to a domain (a.b.edu).  It connects properly and I can see the directory groups in the that tab when we Select.   This domain (a.b.edu) has a two way trust with another domain in another forest (x.y.b.edu).  However, I do not see the groups in that domain and I cannot seem to manually add those groups using the Add on the free text Group Name.
 
The documentation is not clear on this point:  Page 8-41 and 8-42 of the "User Guide for the Cisco Secure Access Control System 5.2) says:  "The External User Groups dialog box appears displaying a list of AD groups in the domain, as well as other trusted domains in the same forest." This implies to me that it cannot cross forests even though a trust is set up.  This seems to be what is happening.

View 5 Replies View Related

How To Setup Multiple Ethernet Connections In Windows 7

Jul 16, 2011

I have to connect/switch to two different ips different gateways, can I possibly keep two set of ips always ready.

View 1 Replies View Related

How To Connect Multiple Virtual Machines On Windows 7

Apr 22, 2013

I have installed 4 virtual machines using virtualbox on a windows 7 host and i'm searching how i could connect them so as they can communicate each other.

View 2 Replies View Related

Protocols / Routing :: Two Domains In One Exchange Server?

Aug 28, 2012

Currently, my company runs a DC and exchange server in the building. It is also hosting our website with IIS7. All AD users currently have @company1.com.au email addresses.We have just started an off shoot company and would like to setup emails in exchange so that we can automatically assign and manage emails on the same exchange server. so that each user hasWhat is the best way to do this?At the moment, company2.com - company is hosted outside with someone else. Is there a way that he can direct the mail to us so that he hosts the website but we host the email server?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved