Hosting Website On Network - Doesn't Resolve Locally?
Dec 12, 2011
I am setting up a webserver to host our website on our local network. When I'm browsing from an external network, I can pull our website example.com and a sub domain test.example.com. However, when I'm browsing from our internal network, I cannot pull up test.example.com. I am not sure if this is due to propigation issues or what.When I do nslookup from external, it shows my network's main IP address. When I do it from local, it can't find an address and says non-existent domain.Should I have any problems connecting to my website if it is using my external IP address? Will this be a loopback problem? If so, how can I resolve this?
View 3 Replies
ADVERTISEMENT
Apr 12, 2012
I am running a webserver locally and I am unable to resolve it by domain name (e.g. mydomain.com) when I am inside my network. However, I am able to hit it internally (e.g. 192.168.0.10) just fine. When I try to access mydomain.com from inside my network it comes up with my Actiontec router's admin page on 192.168.1.1.Here is my configuration:Actiontec FIOS router 192.168.1.1 (connected to internet)DHCP disabled Netgear Router 192.168.1.2 is in the DMZHas cable running from Actiontec's LAN port to Netgear's WAN port[CODE]
View 7 Replies
View Related
Aug 13, 2012
I have a fixed external ip address.I have port forwarding setup for accessing a NAS inside my LAN, lets say port 12345.Now when I use my laptop outside my own LAN, e.g. 99.99.99.99:12345 resolves nicely to my NAS. But when I use the same 99.99.99.99:12345 inside my LAN, it does not resolve. Instead, it gives me a 'server takes too long to answer' error
I have also setup a virtual host to an ip cam inside my network. That one resolves just fine. I tried enabling remote management on the DIR-655 and also that works fine using 99.99.99.99:8888.When I replace the external ip address with the internal ip address of my NAS, thus bypassing port forwarding, it obviously also works ok.
Why the forwarded ports are not accessible when I use my own external fixed IP address? Does the DIR-655 treat it different than other external IP addresses?
View 4 Replies
View Related
Apr 1, 2011
I have a computer that can no longer connect to the internet whether through the wireless or wired directly to the router. The computer will recognize and connect to the network locally. Two other computers are on the network and they are connect just fine.
[code]...
View 13 Replies
View Related
Jan 8, 2012
I had setup 2 servers at home. I'm now in need of hosting 4 websites. I have 4 static public ip's. I'm currently using a router with DD-WRT firmware installed. I have setup up as static NAT. X.X.X.27 to 192.168.0.100, X.X.X.28 to 192.168.0.101. This is my current setup for the existing 2 webservers which host a website each. I notice apache allows for multiple websites per server. One of the server's is a dell 2500 with 2 NIC's and will not be a problem assigning two ip's. The second server only has 1 NIC. Should I buy another NIC card for the second server or could I get by using a virtual NIC? The load on the servers isnt heavy. Only bout 20 clients connect to them daily.
View 8 Replies
View Related
Mar 16, 2011
my internet doesnt allow access to thepiratebay.org. Why?
View 1 Replies
View Related
Oct 26, 2012
It won't open on some computers (of different ISP) I;ve tried different Operating systems and browsers... if I check the website, it is mostly up and works perfectly on other computers... If I try to ping it, Sometimes I manage but more often it fails.. Any time the browser says dns error - server cannot be found. I don't know much in IT, but I guess ip doesnt matter, because my computer obtains it from ISP.the website address is armtravel.org... what's the problem ? hosting, 3 ISP-s (that i've tried to open with) or computers (more than 10 don't open)
View 3 Replies
View Related
Dec 25, 2011
cd doesn`t work and can access web for set up
View 1 Replies
View Related
Jan 12, 2012
I had the website filter ON and it was working very well to block a few websites on a schedule. And after a few month, it doesn't work any more. While it is possible that I scewed up the setting , I have tried so many settings.
So:DIR655 fw 1.32NA,hw A3,"Enable access control" is on with the desktop MAC address (used copy this MAC)(I have also tried my laptop MAC),web site filter is set to "deny",the router time is set using NTP dlink server,
View 3 Replies
View Related
Nov 25, 2012
What is the best hosting for vpn. I'm thinking bluehost, but is there anything better/cheaper. I prioritize the features: reliable, features (ftp, ssh, phpbb, perforce, etc.)
View 1 Replies
View Related
Feb 8, 2012
I need to be VPN'd in to work all day but during the day I need to print to my home network printer. The work around has always been to press print then disconnect from VPN, wait for the document to finish then reconnect VPN. This is starting to get on my nerves and I was hoping that there was a way to be on VPN through my physical LAN and maybe print over my wireless network. Is there a way to separate traffic in Windows 7?
View 2 Replies
View Related
Mar 29, 2011
You are appointed as a system administrator for a large company which has its own computer intranet hosting 150 workstations and around the same number of users. Write few points explaining the roles you would expect to take on as part of your new employment in terms.
View 2 Replies
View Related
Feb 21, 2011
Is it possible for Windows 7 to host multiple domains? I have seen that it is available for plenty of other OSs and I am sure that it is. I just wanted to make sure.
View 2 Replies
View Related
Feb 28, 2012
I am playing Hidden Stroke online and i can join games but i cant host, when i create a game my IPV4 address shows up instead of my IP address which means no one can see the game. I am a guest PC on my home Wifi.PS i have already opened all the ports that the game requires to play.
View 5 Replies
View Related
Mar 23, 2011
On Windows XP, my integrated NIC stops working after hosting a server. The server starts fine, ports are forwarded, firewall is down, modem is fine, but when I receive a connection, it shows they have made a connection, but then they drop, as do I. I can't browse or ping anywhere. I have to physically disconnect, then reconnect the ethernet cable to the port, or restart the computer. Upon ipconfig, the adapter is set with the Windows default ip (169.x.x.x) and cannot be /release'd or /renew'd.
View 10 Replies
View Related
Aug 23, 2011
So 3 days from now im getting comcast cable....12 mbps download and 3mbps upload (something like that)I want to know if I can host servers in online games such as... modern warfare 2 and black ops...pretty much any popular first person shooter. I noticed that every game I play I am not host and I am lagging...my current connection is 2.5 MBPS download and 0.4 MBPS upload.
View 9 Replies
View Related
Apr 30, 2013
I recently signed up with AT&T U-Verse. They required that I buy a 2Wire 3600 HGV router. I looked up how to forward ports -- and even called an AT&T representative -- and I am sure that I forwarded them correctly. I'm trying to host a Minecraft Server. I forwarded port 25565 in TCP and in UDP. After that wouldn't work, the AT&T representative said that the traffic was being blocked from my side. I then checked my Windows Firewall and allowed all proper applications -- Minecraft and Minecraft Server. When that wouldn't work, I went in an manually added exceptions to Windows Firewall for TCP - 25565 and UDP - 25565 Inbound and the same for Outbound. Nothing.I have tried to check the ports in DMZ mode with Windows Firewall disabled -- they are still timing out. What should I do?
View 7 Replies
View Related
Jan 9, 2012
I am running a smaller hosting company and i am currently looking at a Cat6506 switch with a SUP720 Supervisor Engine. I have also been looking at a Cat6509 with a SUP2-GE Supervisor Engine. At the moment i am getting my connection from a ISP but i am going to get my own BGP AS now.. My question is just, how much will the SUP720 be able to route, and how many routes will i need to get it to route my packets in and out of my AS? I have seen that the full BGP table is over 400,000 and the SUP720 is only capable of 256,000, but do i really need the full table? I
major differences between the SUP720 and SUP2-GE Supervisor Engines?
View 7 Replies
View Related
Dec 24, 2011
a few days ago i had a router dlink 2740b and i made a dedicated server of call of duty4 where my friends and i played. yesterday i changed my router with another dlink 2740b f1 version (a new version of the same router): i make port forwarding for the cod4 server but the server doesn't go online....i see it only in local....but my friends and i don't see it in the internet server in the game menù...
View 1 Replies
View Related
Aug 7, 2011
how much RAM is requied on server hosting CiscoWorks. Our CiscoWorks is running like snail. We have 3200 logical devices configured on it. Specially browing different pages of CiscoWorks is very very slow.
how big hard drive will be enough for CiscoWorks with below applications installaed and configured with 3200 devices.. Currently we have 65GB Harddrive and its 85% full.
Server Platform: Windows 2003 server 32-bit
Server RAM: 4GB
Hard Drive: 63GB-CiscoWorks is installed on this Harddrive.
Another Partition of Harddrive is 130GB and its 100% free.
LMS: 3.2.1
RME: 4.3.1
CM:5.2.1
View 2 Replies
View Related
Nov 8, 2012
I was able to access my website jetbaby.com just fine before I changed the cPanel password. Now I cannot even load the site or load the cPanel login page here: jetbaby.com:2082 All I did was change the cPanel password. When I use another computer that is NOT on my network, I can connect to the site fine. I'm assuming that my network is blocking it for some reason after the cPanel password change. I tried the IP address in the address bar as well (still no go). Cannot "ping" the IP address either. I reset my modem and router as well. Cleared cache in browsers as well. I also disabled firewall and anti-virus for testing.
View 2 Replies
View Related
Jul 12, 2011
We're trying to set up netflow based billing for our hosting environment. We're dual homed to two different ISPs using BGP peering with each (ASN 18817). The drawing below shows the logical setup: The routers are each Cat6506E with Sup32 and PFC3B/MFSC2A running 12.2(33)SXJ. The direct link between is layer 3 (routed ports) for iBGP peering. The dark line is a layer 2 LAN made up of multiple switches (not shown) each connected to both 6500's with spanning-tree for loop protection. These switches also provide a layer-2 path between routers but the configured BGP peering is set to the layer-3 port IP on the link. There is at least one firewall connected directly to a 6500. The firewalls are all ASAs connected to any one of the not-shown mid-span switches. The router interfaces to the layer-2 LAN is a VLAN SVI using GLBP to provde a redundant gateway. There are multiple subnets on this vlan configured as secondary IP addresses on the VLAN interface (and in the GLBP gateway configs).
The question is: how do we collect stats from all traffic to/from the internet without collecting any local traffic (firewall to firewall) and without getting duplicate flows sent to our collector?
I was hoping to just put "ip flow ingress" and "ip flow egress" on the ISP facing L3 ports but that's not actually collecting outgoing flows (appears egress netflow may not be supported on the 6500). I added "ip flow ingress" to the VLAN interface but that didn't seem to fix it so I also addes the global command "ip flow ingress layer2-switched vlan 50". However after a small change to the layer2 LAN some (but not all) of our clients saw a near doubling of bandwidth (according to netflow). We compared the netflow stats to the server port usage stats for one client and it looks like we were under reporting before the change and appear to be over-reporting now. I'm thinking the overage is either because we're counting MLS traffic flowing between subnets on the layer-2 LAN but can't verify. With GLBP moving the default gateway and MSTP blocking at least one uplink from a mid-span switch to a 6500, traffic flows can be difficult to predict. Especially when you don't know exactly when a flow gets accounted. For instance, if a packet comes into one 6500 becase that's the only layer-2 path to the gateway BUT the gateway is currently on the other 6500, does the first 6500 count that flow or does the second one count it or will both? etc etc.
View 1 Replies
View Related
Nov 22, 2012
I'm on a PC with XP spk3 and my broadband speed is 30+ Mb. In any browser, if I go to Vimeo, Youtube etc and watch higher quality vids I get terrible stuttering of picture and sound, really bad crackling and warbling and drop outs. But, if I download the same vids, they play fine on my computer. I've updated everything I can think of and there is no improvement. My machine is old and slow but this problem started just the other day and it was bad from the start. It didn't gradually creep up.I'm at a loss.
View 3 Replies
View Related
Oct 9, 2011
during the first set up I have set a password as it was requested during the installation routine. After the installation, I added the camera's IP to my browser (tried IE9 and FF). In both cases I was asked to enter the user name and the PW, but I can't access the 930. I'm using the very same PW as I had set up during the routine, but none of the browsers accepts the PW.
View 6 Replies
View Related
Aug 19, 2011
I would like to setup multiple DMZs for our hosting servers. Currently there is a single DMZ in which our reverse proxy servers are connected using a public IP address. The idea is to have the reverse proxy forward the request from the Internet to the hosting servers in another DMZ. The purpose of the hosting DMZ is to protect it from the outside as well as from the inside. There will also be a development DMZ where we can test content prior to going live with the website.
Network: We currently have two Cisco 6509's (Core) with a FWSM in each running active/stanby configuration. There is a 10Gb Fiber connection between each Cisco switch to two Cisco 4948s (Top of Rack Switches). I can either setup OSPF or Trunking between the core and top of rack switches. The Cisco 4948s will support VLAN 7 (hosting DMZ 10.0.7.0/24) and VLAN 8 (development DMZ 10.0.8.0/24). Each webserver is connected to both Cisco 4948 for redundancy.
Question: If I have a single interface connecting both VLANs 7 and 8, either through Layer 2 or 3, then how can pass both DMZ traffic to the appropriate servers? The reason why the servers are in the same rack connected to the same two switches is that we are using Blade Servers and VMWare.
View 3 Replies
View Related
Jan 17, 2013
We have been noticing a strange issue since upgrading to Comcast Business with a new Motorola 6580 modem/router:certain common websites can no longer be accessed via the network (although they load fine when accessed via smartphone 3/4G)I already did some reading on the subject and it looks like the Firewall is to blame:when I switch Firewall to "Off", everyone can access the websites ok,as soon as I switch Firewall back to "Low" - no more website access.Question: is there any workaround for this issue other than turning off the Firewall?
View 1 Replies
View Related
Nov 5, 2012
I was able to access my website [URL] just fine before I changed the cPanel password. Now I cannot even load the site or load the cPanel login page here: [URL] All I did was change the cPanel password. When I use another computer that is NOT on my network, I can connect to the site fine. I'm assuming that my network is blocking it for some reason after the cPanel password change. I tried the IP address in the address bar as well (still no go). Cannot "ping" the IP address either. I reset my modem and router as well. Cleared cache in browsers as well.
View 1 Replies
View Related
Apr 23, 2012
I need viewing a DVR camera system remotely through a Motorola Netopia 3347 router. I was able to view the system properly for a year with the old ATT modem and a separate router, but recently the modem crashed and ATT replaced it with this Netopia that I can't for the life of me, understand.I can view locally but not remotely from the internet. I need establishing the Pinholes properly. I'm trying to get it working for port 85 for the DVR system. But I'm confused on the Internal vs. External port #'s it asks for in the Pinhole screen. No combination I enter seems to work. I even tried just using port 80 to get it working, but there was a conflict creating a pinhole for 80 since its already mapped to HTTP.
View 5 Replies
View Related
Mar 11, 2012
I installed my first IP camera. Things seem to have went ok with the installation andd router. I can view the video live from mydlink.com.I've tried the dlink software, but it can't find the camera so I can control recording options, ftp, etc. i've also tried 3rd party software that can't find my camera.I'm fairly internet savvy, but do not have access to my router admin atm. (cable company installed their own) My home ip address is supposed to be dynamic. I thought that would cause me problems viewing from mydlink.com, but it hasn't so far.
View 5 Replies
View Related
Dec 20, 2010
I redistribute our MPLS eBGP routes into our internal EIGRP process at each site. This action undesirably redistributes locally generated BGP networks (via network command) that are meant from the MPLS cloud into our internal routing process.I currently have a route-map on my 'redistribute bgp' command that filters each network manually with an ACL. This works but adds obvious administrative overhead; each WAN router advertises different networks, and the ACL must be updated for each new network.Would it make more sense to simply deny routes from BGP to EIGRP with a metric of 32768? Something like this,route-map deny-local-bgp deny 10 match metric 3276 router -map deny-local-bgp permit 20,router eigrp 100 redistribute bgp 65104 route-map deny-local-bgp.
View 19 Replies
View Related
Sep 14, 2011
I configurated ipsec remote vpn at catalyst 6500.
192.168.14.0/24-- my servers are assigned this subnet
vpn user:10.10.10.0/24
192.168.10.229 ---- webserver ip address
[code]...
View 3 Replies
View Related
Jan 13, 2012
VPN client 5.0.07.0410 on Windows Vista sp2 when I try to connect to my cisco 851.Secure VPN connection terminated locally by the client Reason 412 The remote peer is no longer responding.I turned on debug crypto isakmp and debug crypto ipsec no information displayed on the console.I was a lot futher before but now do not know where to turn.
View 3 Replies
View Related
Apr 24, 2011
One of my VLANS on my 3750 gives a status of act/lshut. I've tried no shut commands on the interface to no avail. From my reading it seems like this means the VLAN is active but shut down locally.
View 8 Replies
View Related
