I need to be VPN'd in to work all day but during the day I need to print to my home network printer. The work around has always been to press print then disconnect from VPN, wait for the document to finish then reconnect VPN. This is starting to get on my nerves and I was hoping that there was a way to be on VPN through my physical LAN and maybe print over my wireless network. Is there a way to separate traffic in Windows 7?
View 2 RepliesI have a computer that can no longer connect to the internet whether through the wireless or wired directly to the router. The computer will recognize and connect to the network locally. Two other computers are on the network and they are connect just fine.
[code]...
I am running a webserver locally and I am unable to resolve it by domain name (e.g. mydomain.com) when I am inside my network. However, I am able to hit it internally (e.g. 192.168.0.10) just fine. When I try to access mydomain.com from inside my network it comes up with my Actiontec router's admin page on 192.168.1.1.Here is my configuration:Actiontec FIOS router 192.168.1.1 (connected to internet)DHCP disabled Netgear Router 192.168.1.2 is in the DMZHas cable running from Actiontec's LAN port to Netgear's WAN port[CODE]
View 7 Replies View RelatedI am setting up a webserver to host our website on our local network. When I'm browsing from an external network, I can pull our website example.com and a sub domain test.example.com. However, when I'm browsing from our internal network, I cannot pull up test.example.com. I am not sure if this is due to propigation issues or what.When I do nslookup from external, it shows my network's main IP address. When I do it from local, it can't find an address and says non-existent domain.Should I have any problems connecting to my website if it is using my external IP address? Will this be a loopback problem? If so, how can I resolve this?
View 3 Replies View RelatedI'm on a PC with XP spk3 and my broadband speed is 30+ Mb. In any browser, if I go to Vimeo, Youtube etc and watch higher quality vids I get terrible stuttering of picture and sound, really bad crackling and warbling and drop outs. But, if I download the same vids, they play fine on my computer. I've updated everything I can think of and there is no improvement. My machine is old and slow but this problem started just the other day and it was bad from the start. It didn't gradually creep up.I'm at a loss.
View 3 Replies View Relatedduring the first set up I have set a password as it was requested during the installation routine. After the installation, I added the camera's IP to my browser (tried IE9 and FF). In both cases I was asked to enter the user name and the PW, but I can't access the 930. I'm using the very same PW as I had set up during the routine, but none of the browsers accepts the PW.
View 6 Replies View RelatedI need viewing a DVR camera system remotely through a Motorola Netopia 3347 router. I was able to view the system properly for a year with the old ATT modem and a separate router, but recently the modem crashed and ATT replaced it with this Netopia that I can't for the life of me, understand.I can view locally but not remotely from the internet. I need establishing the Pinholes properly. I'm trying to get it working for port 85 for the DVR system. But I'm confused on the Internal vs. External port #'s it asks for in the Pinhole screen. No combination I enter seems to work. I even tried just using port 80 to get it working, but there was a conflict creating a pinhole for 80 since its already mapped to HTTP.
View 5 Replies View RelatedI installed my first IP camera. Things seem to have went ok with the installation andd router. I can view the video live from mydlink.com.I've tried the dlink software, but it can't find the camera so I can control recording options, ftp, etc. i've also tried 3rd party software that can't find my camera.I'm fairly internet savvy, but do not have access to my router admin atm. (cable company installed their own) My home ip address is supposed to be dynamic. I thought that would cause me problems viewing from mydlink.com, but it hasn't so far.
View 5 Replies View RelatedI redistribute our MPLS eBGP routes into our internal EIGRP process at each site. This action undesirably redistributes locally generated BGP networks (via network command) that are meant from the MPLS cloud into our internal routing process.I currently have a route-map on my 'redistribute bgp' command that filters each network manually with an ACL. This works but adds obvious administrative overhead; each WAN router advertises different networks, and the ACL must be updated for each new network.Would it make more sense to simply deny routes from BGP to EIGRP with a metric of 32768? Something like this,route-map deny-local-bgp deny 10 match metric 3276 router -map deny-local-bgp permit 20,router eigrp 100 redistribute bgp 65104 route-map deny-local-bgp.
View 19 Replies View RelatedI configurated ipsec remote vpn at catalyst 6500.
192.168.14.0/24-- my servers are assigned this subnet
vpn user:10.10.10.0/24
192.168.10.229 ---- webserver ip address
[code]...
VPN client 5.0.07.0410 on Windows Vista sp2 when I try to connect to my cisco 851.Secure VPN connection terminated locally by the client Reason 412 The remote peer is no longer responding.I turned on debug crypto isakmp and debug crypto ipsec no information displayed on the console.I was a lot futher before but now do not know where to turn.
View 3 Replies View RelatedOne of my VLANS on my 3750 gives a status of act/lshut. I've tried no shut commands on the interface to no avail. From my reading it seems like this means the VLAN is active but shut down locally.
View 8 Replies View RelatedI am using the window server 2008 and configure tcp/ip properties correct ping locally reply successful when ping localy but when ping yahoo.com then reply destination host unreachable whereas gateway and dns ip is also correct configure so tell me solution about this problem because i am useing the internet.
View 1 Replies View RelatedWe are planning to implement Cisco wireless in our central office and branch office using Cisco 2504 WLC and Cisco 1602i Ap. Our branch office is connected via ip vpn and a separate broadband connection for urgent requirements. Usually all users are allowed to browse through central proxy server.I have been trying to find any possibility of giving guest access (web authentication) for branch office guests utilizing only the broadband connection which is connected to the branch office. Is there a possibility that Central WLC is reached using NAT from the BranchOffice AP and allowing guests to authenticate and surf the web at times IP VPN is unreachable.
View 4 Replies View RelatedI have a Pix 515E with a VPN setup. I recently tried to connect Cisco VPN Client and get the following error: "Secure VPN Connection terminated locally by the client. Reason 412: The remote peer is no longer responding" I have previously been able to connect to this VPN using Cisco VPN Client without issue. Below is a copy of my config and VPN Client log & debug logs from Pix. We have Newwave Communications Cable internet, which i just found out the the ISP has recently implemented DOCSIS 3.0. (i'm not sure if that matters).
*******************************************************************************************************************************************
pix1(config)# sh run
: Saved
:
PIX Version 6.3(4)
interface ethernet0 auto
interface ethernet1 auto
nameif ethernet0 outside security0
[code]....
I just purchased the EA4500 router and went through the setup with no issues. The only problem is I cannot access the router either locally or through the Smart Wifi dashboard. Everytime I go to the page with "Access Router", enter the password and clikc the "Submit" button it does nothing...no incorrect password prompt or idle prompt...almost like the page is broken somehow. I've done all of the usual, restart router, restart PC, restart cable modem, etc. and always having the same result.
View 4 Replies View RelatedI currently have Nexus 5596 pair with VPC peer link Po1 between them. My goal is to connect our new Nexus 7Ks to the 5K's using Fabric Path. My question is during this inital setup with the 7K's. Can I use the same port channel number on the 7K's as I did the 5K's? Is the port channel locally significat?
View 2 Replies View RelatedThe scenario I am facing is, trying to have the ability to print from my laptop computer remotely to my home printer which supports IPP.What I did so far was to make sure that I enabled IPP in the printer. So the URL is 192.168.1.101:631. (I am able to connect and print to the printer on local network usinghttp://192.168.1.101:631.) I then went into my router and enabled port forwarding for that address and made sure to specify port 631. It doesn't work. I took the following steps: (It works neither with XP or 7)Windows 7 Steps:1. Start-Devices and Printer2. Add a printer3. Add a network, wireless or Bluetooth printer4. Clicked "The printer that I want isn't listed5. Choose "Select a shared printer by name" Below is the scheme I followedWhat is the proper way of setting this to function properly so that I can print to my computer remotely. I want to be able to print to the printer directly and not through a server or another computer. Is this even possible?
View 2 Replies View RelatedMy printer is hard wired to my wireless router, allowing me to print wirelessly from my laptop. After successfully printing this way, it is no longer working. I have tried re-installing the software, however, it is unable to "find" the printer. I have tried this from 2 laptops with no success. My wireless router appears to be working as far as internet.
View 1 Replies View Relatedi want give the dos printing from remote desktop to local computer on anotherlocation
View 2 Replies View RelatedI'm having trouble printing from anything other than "windows desktop 1" (exclude "xbox 360 & Apple TV) So I need to know how to setup printing on the "macbook pro", "Windows laptop" & "windows desktop 2" These computer (except the macbook) all were connected once and I did have home group successfully connected to share the printer between them all as long as "windows desktop 1" was on. But now there in the setup in the pic and the home group and printers don't communicate with each other anymore.
View 3 Replies View RelatedFrom my Dell Vostro laptop I can connect to the internet but cannot print wirelessly on any of my three printers. The Mac computer in the house works on one printer.Not really sure where to start working on this problem.
View 1 Replies View RelatedA weird issue that came up a couple weeks ago, about 15 users that print to network printer via IP. The printer is attached to a print controller with all print jobs are spooled to.
So when a user prints, lets say three pages, it spools to the windows queue and each page takes about 1.5min to get to the print controller queue, when it would only take a few seconds to spool.
Different switches, print drivers..etc have been tried and narrow it down to one thing. When working with the NAS server plugged into the switch, that's when it takes long but when unplug from the NAS, prints come out fast like normal.
how to find out if the NAS is broadcasting some crazy traffic? but it seems that it's only affecting this printer, other printers that don't have a controller print out fine and fast.
A friend has asked me to work with him set up a new office. He already has a PC and a phone line but not broadband, so he is going to organise that and getting a wireless router.He wants a wireless colour laser printer so that his visitors/guests can print easily from his office, or the next office. Does he really need a wireless printer to do this? Or if I plug a network printer directly into his router with an Ethernet cable, same with his PC, will that enable laptop users to print wirelessly (assuming they know the router passphrase of course)? I guess they would need to install the relevant printer driver to do this too.
View 2 Replies View RelatedI have walked into a company that has several small (1-4 PC's each) remote locations, and they all connect to Terminal Server to use our POS app. This app will not keep redirected printers saved between each session, so in order to save the printers, they have software VPN's set up on each client, then the local printers are installed on the server through a Local Port using the VPN ipaddressprinter share name. This allows the printers to be saved in the program and not re-assigned each session. Now, let's say that I have implemented a new desktop replacement procedure, and we are now in phase one of said procedure. I have purchased Windows 7 64-bit desktops. After setting up my deployment standards and testing in-house, I placed one of these PC's in the field. This is where I learned the issues of printing from a 32-bit server to a 64-bit client. I have not been able to successfully print to the printer installed on the server using the Local Port of the client, print job errors out. I have done some research, and found the issues with printing from 32-bit to 64-bit, and have installed all the additional drivers I can find, with no success.
View 1 Replies View RelatedI am trying to protect the computing assets on a perimeter firewalled / protected LAN from visiting laptops while still permitting the laptops wifi internet access and printing priviledges on the LAN's networked HP printer To do that I was thinking of setting up a computer as a dedicated firewall with 3 NICs (external internet, internal LAN and a DMZ for a Guest wifi router for use by the visiting laptops). (Will probably use free Untangle Firewall software software or such on the dedicated firewall computer).What I can't figure out is the firewall's topology, IP ranges and rules / forwarding that would permit such laptop operation.I would think it would be a common need for small offices but can't find much material on the subject.I do understand that such would slightly weaken the firewall but feel that I would gain more security overall.
View 2 Replies View RelatedShared printer not printing. Have two PCs, one with Vista OS with the printer connected and the other XP, both connected via network sharing. I cannot print from the XP PC. It says I do not have permission even though I have shared the printer.
View 4 Replies View RelatedI've tried scanning for viruses, using winsock fix (they had a static ip I also set to automatic since they should not need it). I just turned off the firewall as well, tried "selective startup" and unchecked "load startup items" and nothing has worked so far. We're working on giving them another computer but I'd like to know why this happens.
View 7 Replies View RelatedI've been having an issue with all the printers and print servers on my network. They work great with my wife's computer which runs XP, but my computer which runs 7 won't print. Tried a Cat 6 cable on one and got some results.
View 1 Replies View RelatedHow do I get note pad started on my computer. When I want to print something the computer tells me I need to use notepad first.
View 1 Replies View RelatedIm having some printing issues whenever im working on the terminal server. If I try to print a document out in "landscape", it will print out "portrait", seen though it displays properly in landscape in the print preview. If Im working locally on my PC, it prints out fine.
View 2 Replies View RelatedI am using Open-VPN to connect directly to our server at our office. We have a main network printer at the office that everyone uses. While hardwired, I added the printer to my laptop. When I am at the office, either wired or wirelessly, I can print to the printer. When I try to print from home, the printer never opens, it is unable to connect. Is there a way to access a network printer when logging in remotely through VPN?
View 9 Replies View RelatedI've been having an issue with all the printers and print servers on my network. They work great with my wife's computer which runs XP, but my computer which runs 7 won't print. Tried a Cat 6 cable on one and got some results.
View 2 Replies View Related