Added RAM To HP Pavilion A6000n PC Now Wireless Not Working
Jan 2, 2013
I added RAM to my HP Pavilion a6000n PC, and the only downside is that it no longer identifies the Netgear WNR1000v2-VC router as wireless.I run Windows 7 - have Comcast Internet and have an Arris TM722 modem.The modem and router were supplied by Comcast.I reloaded the cd that came with the router, everything appears to be on the hard drive, but the wireless is still not "enabled". The computer shows the connection as a local area connection, even though the modem and router are connected to each other and the pc.
View 2 Replies
ADVERTISEMENT
Mar 7, 2012
I just added a X6704 card to our 6513 switch, and it is not working correctly. We are running 12.2(33)SXI5. [code]
View 5 Replies
View Related
Aug 29, 2012
My usb devices- whenever I plug my Belkin usb internet adapter in I get an error noise (3 beeps) and the device does not power on. I tried another one (Cisco) from a different PC and got the same error. Tried this on all the ports and updated the drivers. All other USB devices work fine, tethering my phone to get internet for now. Had been using the device without problems for months until getting the error. The error started occurring when I unplugged it and plugged it back in. Using Windows 7 x64 on an HP Pavilion.
View 1 Replies
View Related
Apr 3, 2011
Had a look inside my HP Pavilion p6685l recently and found there wasn't any wifi card which was odd because it's been working fine for months.Device Manager says theres a 802.11n Wireless Lan Card in there but I traced the wires from the ariel to a chip on the board (MSI 2A9C according to Belarc ). Property sheet says it's a Ralink Card and so does the vendor id ( 1814 ) but the device id (3092) belongs to an Intel I20 1.5 Raid Controller which is where I got lost. I didn't know Raid Controllers did wifi.
View 14 Replies
View Related
Aug 19, 2012
I have a HP desktop Pavilion p6531 p-b (Windows 7) that is hardwired to a Linksys 2500 Router. Internet worked fine until this morning where it can't connect at all. It can pick up the Wireless connection from the router but I can't get it to go online even wirelessly (although I am not sure if I'm doing that part right). I called my ISP and they reset the modem, etc as well as bypassing the router and we still cannot connect to the web. We looked at the Network Center and made sure that in the Local Area Connection, the Internet Protocol Version properties all have "Obtain address" and "Obtain DNS server" automatically checked. At that point their tech support was stumped.
View 6 Replies
View Related
Feb 27, 2011
I recently installed a wireless printer and all seemed to work well until the next day. I am able to get on the Internet with my iPad but not my PC. I've tried winsock fix, ipconfig, netsh commands and other stuff but I can't connect to the Internet. When I tried to run ipconfig/all here's what I got:
An internal error occurred:The request is not supported.
View 13 Replies
View Related
Dec 27, 2011
I have a friend who asked me how he could stop his children accessing porn etc on their ipods etc that they pick up from a wireless router.Is it possible to route a wireless signal through a computer that has parental controls?
View 1 Replies
View Related
Sep 30, 2012
Nice for those who want to see what it looks like:
Cisco Connect Cloud: [URL] EA6500: [URL] . And of course all other Linksys devices: [URL]
View 1 Replies
View Related
Feb 26, 2012
I just added a wireless router netgear wgr614 and I secured it and it worked for one day and then after that no internet connection. I've rest and unplugged both the modem and the router and still nothing.
View 1 Replies
View Related
Aug 4, 2011
I finally added wpa personnel security to my network. It worked on all computers until my sons xbox wouldn't connect so I disconnected the modem and router and reconnected. After this, the main computer at the router worked but 3 other laptops wouldn't connect to the network. I finally realized it wasn't broadcasting the ssid.All are working except I have an order computer running xp that previously worked-I hadn't checked it for a week-Ibut I just checked and it doesn't connect to the network. It finds the signal and I put the password in but it won't connect. I've deleted the connection and added it back with no luck.
View 1 Replies
View Related
Jul 20, 2011
I have Linksys WRT320N acting as AP with Mac filtering, yesterday I noticed that even not added Mac addresses can access the network!!The settings in Mac Filter page as following:EnablePrevent PCs listed below from accessing the wireless network.MAC 01: XX:XX:XX:XX:XX:XXMAC 02: XX:XX:XX:XX:XX:XX...when I changed it to "Permit PCs listed below to access the wireless network" no one is able to connect to the network!!!I think the AP is not accepting the MACs I added!I restart the router (Turning on and off) with no luck.Firmware Version: v1.0.03.
View 1 Replies
View Related
Nov 13, 2011
I am installing LMS 4.0 in my site newly I have nearly 1000 devices in network .When i had tried the autodiscovery mode using ping sweep method the devices are getting discovered but showing us unreacheable . All the devices are going under unreacheable no devices are getting added to the DCR .SNMP settings are configured correctly.
whether the autodiscovery will add the devices to DCR or i need to add the devices manually.As per my requierement i need to configure below things , is it possible to configure the same
1)LMS as SYSLOG server
2)LMS should send EMAIL notification if device goes down , interfaces goes down , memory / cpu goes high ,switch module goes down
3)Need to know if cisco releases new device packages how we will update to the cisco works .
View 4 Replies
View Related
May 2, 2012
I've lost my connection.The F12 key remains lit orange when I push it.There is no button on the laptop.i tried pressing Fn and the F12 key, but that does not turn the wireless on. what else can I do.(My desk top computer remains connected to wireless).
View 3 Replies
View Related
Mar 25, 2013
when we add new switch to STP converged enviroment, switch flush the data from the data base.how to protect database from deleting the information
View 10 Replies
View Related
Aug 26, 2012
i have planned a deployment with one acs in Europe working as primary, one acs in europe as secondary and one acs in USA as secondary also.
I can add one acs in europe to the deployment as secondary. When I try to add the acs in USA to the deployment - Nothing really works.
The status shown in the primary is offline (red) and status pending. It stays like this for hours. When I log in to the gui directly on the acs in USA, it still has status primary.
The two acs are transparently connected. There is WAN optimization (cisco waas) in between the two datacentres..
View 1 Replies
View Related
May 30, 2011
We have just installed LMS 4.0.1 and started to discover parts of the network. After the discovery process finished successfully - 100+ new devices were added to DCR message - I was able to see the devices by clicking on their number but when I go to Inventory-Add/Import/Manage Devices I cannot see any device in the Group that I created.If I restart the CiscoWorks Daemon Manager process the newly discovered devices are added to the custom Group. This seems like a bug as I had a LMS 4.0 evaluation installation a few months ago and device discovery was working fine meaning the devices were added immediately to the Inventory.
View 4 Replies
View Related
Jan 16, 2013
For over a month now my laptop has been unable to connect to the internet via a wireless connection. It will connect to the network, but that's as far as it goes. Resetting the router does nothing, and the same can be said for resetting the network wireless adapter. However connecting via the LAN cable to the Router will allow me to connect to the internet and use it normally.I've even tried deleting the wireless information for my network off the computer and re-inputting it but that didn't solve the problem either.I have an HP Pavilion g7 notebook PC that is running Windows 7. I got in it June 2012 brand new and have had nothing but problems with the wireless. It worked fantastic for the first few months and then this happened for the first time. I managed to fix it by myself that time, but I don't remember exactly what I did. It worked alright for the next few months but it was kind of spotty and temperamental. And now it's not working at all. I've tried everything I can think of to fix the problem but nothing has worked so far. According to the HP support Assistant my wireless adapter is called "Intel(R) Centrino(R) Wireless-N 1030"
View 5 Replies
View Related
Mar 12, 2012
I recently took my laptop (HP Pavilion) running Windows Vista, with me on vacation. I got it to work there but it won't work wirelessly now that I'm home.
View 14 Replies
View Related
Apr 25, 2011
My hp pavilion laptop says I'm connected to my wireless but I cannot get any web pages to work. I did a-wireless network diagnostic test n it say problem w wireless adapter or access point. My wireless router is linksys model wrt160n v3. Laptop is windows 7 hp g6-144dx.my hp support keeps telling me I need to take action on atheros LAN but it will not update It has been saying this for about a month. Weird thing is I can get wireless on two iPods from the same router
View 5 Replies
View Related
Feb 20, 2012
I have win7 on an HP Pavilion dv7. I came to my friend's house before, and his WiFi didn't come up as an option to connect to. I unplugged and plugged back in the router, and that worked and I was able to connect with no problem. But today, that didn't fix the problem. I have restarted my computer and the router several times, I have deleted the corresponding wireless profile under "manage wireless networks" list, I have turned off my McAfee firewall to see if that was blocking the connection, I have tried connecting manually through the network and sharing center, I have troubleshooted my wireless adapters (Atheros AR5009 802.11 a/g/n and Microsoft Virtual WiFi Miniport Adapter), I have turned off and turned back on my HP wireless assistant, I have updated the dirvers for the two adapters, I have installed the latest windows updates, I have done all I can think of. And it's not the router, because my cell phone can connect, as well as the other computers in the house, without any problems.
View 8 Replies
View Related
Feb 8, 2011
I added the network printer cum scanner - cm1312, going to control panel >> add printer >> etc. etc. Now I can print. But there is no scanner installed. What I can do?
View 5 Replies
View Related
Aug 22, 2012
I am pretty new to Cisco - and I have a little 506E that I love. I got it working with my first scenario where I have one server that is my web, and e-mail server.I also opened the RDP port so I can remote into it. The IP's for the old server are internal 192.168.1.23 name ferbweb-external 71.12.111.219 name ferbwebpub. Now - I need to add another server in the exact same way with the same ports 80, 25, and 3389 open to the outside - IP's internal 192.168.1.31 name ferbmail and external 71.12.111.220 name ferbmailpub.I can get to all of these ports on the new server on the inside network - so that is not the problem.So, I went into the config, copied the statements for the old server, and changed them for the new server and added them to the config. I can still get to the old server from the outside fine, but cannot get to any ports on the the new server from the outside at all.I have done a lot of research, and cannot find what I am doing wrong.
View 6 Replies
View Related
Jun 23, 2011
How many WLCs 5508 can you add to the mobility group?
View 1 Replies
View Related
Dec 22, 2011
I have the Cisco Router 861 whit the IOS c860-universalk9-mz.150-1.M7.bin. I have created a Vlan, but when I create a second vlan, I have this message: "Vlan can not be added. Maximum number of 2 vlan(s) in the database.
I need to add more than two vlan.
View 3 Replies
View Related
May 31, 2011
Note If you configure VPN, the client dynamically adds invisible NAT rules to the end of this section. Be sure that you do not configure a twice NAT rule in this section that might match your VPN traffic, instead of matching the invisible rule. If VPN does not work due to NAT failure, consider adding twice NAT rules to section 3 instead.
View 2 Replies
View Related
Jul 1, 2011
By reruning discovery with new seeds etc I have more devices discovered. Howeverr they are not shown in the inventory, only in the Device Discovery Summary however.
View 10 Replies
View Related
Apr 29, 2012
how can i enable the Bluetooth on my notebook?
View 1 Replies
View Related
Feb 3, 2011
I have a HP Pavilion desktop with an internal wireless media device installed (though it shows up as "USB 802.11g adaptor").However, since a few days ago, it suddenly stops working every few minutes, or sometimes even after a few seconds of connection, claiming the device isn't connected, reconnecting two or three seconds later,as if I had replugged it in again.Everything seems correct in ipconfig when the device is properly connected, and a full reinstallation did'nt solve the problem.
View 1 Replies
View Related
Apr 20, 2013
on my laptop hp pavillion g 7 series is not enabling wifi button it stays orange and i trouble shoot
View 1 Replies
View Related
Nov 25, 2011
My linksys wireless router does not want to connect to my hp pavillion dv 6700. I had tried already tried resetting it, and it still hadn't managed to solve the issue. It might be something wrong with the IP address, or other settings. I can connect just fine to a modem. What do I need to do to resolve this and get back running wirelessly?
View 14 Replies
View Related
Jul 17, 2011
How do i turn on my wireless network?
View 2 Replies
View Related
Dec 27, 2011
I have an HP Pavilion laptop running vista.We got charter internet with a new Motorola wireless router.My laptop will connect to the router but not the internet. My wife's Sony Vaio, running vista, my son's mac, my android phone all connect fine. If I plug in a cable, I am on line, but not wireless.
View 1 Replies
View Related
Jun 5, 2012
I am researching on the behaviors of routers when MTU is increased beyond the MTU set in the routers. Also, when I use jumbo frames instead of normal MTU, how does it affect the network. So, what I plan to do is
LAN_A -- > blackbox --> WAN --------> WAN --> blackbox --> LAN_B
All the traffic coming from LAN_A will be of size 1500 Bytes or less. The blackbox in the center will add an overhead of 4 bytes, recalculate the CRC and transmit the packet on the WAN side. I wanted to know that:
1- if my LAN router and WAN router, both are set at 1500 MTU, then will WAN router drop the packet if it receives a packet greater than 1500B ?
2- If i keep my LAN side to 1500 MTU and I switch my WAN router to Jumbo frames, how will this configuration affect the complete network ? Will it work or not ?
3- I want to add the overhead on every packet coming in from LAN side, so, what options do I have to achieve this goal ?
PS. All types of traffic can come from LAN side.
View 2 Replies
View Related
