Cisco :: LMS 4.0 No Devices Are Getting Added To DCR
Nov 13, 2011
I am installing LMS 4.0 in my site newly I have nearly 1000 devices in network .When i had tried the autodiscovery mode using ping sweep method the devices are getting discovered but showing us unreacheable . All the devices are going under unreacheable no devices are getting added to the DCR .SNMP settings are configured correctly.
whether the autodiscovery will add the devices to DCR or i need to add the devices manually.As per my requierement i need to configure below things , is it possible to configure the same
1)LMS as SYSLOG server
2)LMS should send EMAIL notification if device goes down , interfaces goes down , memory / cpu goes high ,switch module goes down
3)Need to know if cisco releases new device packages how we will update to the cisco works .
View 4 Replies
ADVERTISEMENT
May 30, 2011
We have just installed LMS 4.0.1 and started to discover parts of the network. After the discovery process finished successfully - 100+ new devices were added to DCR message - I was able to see the devices by clicking on their number but when I go to Inventory-Add/Import/Manage Devices I cannot see any device in the Group that I created.If I restart the CiscoWorks Daemon Manager process the newly discovered devices are added to the custom Group. This seems like a bug as I had a LMS 4.0 evaluation installation a few months ago and device discovery was working fine meaning the devices were added immediately to the Inventory.
View 4 Replies
View Related
Jul 1, 2011
By reruning discovery with new seeds etc I have more devices discovered. Howeverr they are not shown in the inventory, only in the Device Discovery Summary however.
View 10 Replies
View Related
Aug 26, 2012
i have planned a deployment with one acs in Europe working as primary, one acs in europe as secondary and one acs in USA as secondary also.
I can add one acs in europe to the deployment as secondary. When I try to add the acs in USA to the deployment - Nothing really works.
The status shown in the primary is offline (red) and status pending. It stays like this for hours. When I log in to the gui directly on the acs in USA, it still has status primary.
The two acs are transparently connected. There is WAN optimization (cisco waas) in between the two datacentres..
View 1 Replies
View Related
Aug 22, 2012
I am pretty new to Cisco - and I have a little 506E that I love. I got it working with my first scenario where I have one server that is my web, and e-mail server.I also opened the RDP port so I can remote into it. The IP's for the old server are internal 192.168.1.23 name ferbweb-external 71.12.111.219 name ferbwebpub. Now - I need to add another server in the exact same way with the same ports 80, 25, and 3389 open to the outside - IP's internal 192.168.1.31 name ferbmail and external 71.12.111.220 name ferbmailpub.I can get to all of these ports on the new server on the inside network - so that is not the problem.So, I went into the config, copied the statements for the old server, and changed them for the new server and added them to the config. I can still get to the old server from the outside fine, but cannot get to any ports on the the new server from the outside at all.I have done a lot of research, and cannot find what I am doing wrong.
View 6 Replies
View Related
Jun 23, 2011
How many WLCs 5508 can you add to the mobility group?
View 1 Replies
View Related
Dec 22, 2011
I have the Cisco Router 861 whit the IOS c860-universalk9-mz.150-1.M7.bin. I have created a Vlan, but when I create a second vlan, I have this message: "Vlan can not be added. Maximum number of 2 vlan(s) in the database.
I need to add more than two vlan.
View 3 Replies
View Related
May 31, 2011
Note If you configure VPN, the client dynamically adds invisible NAT rules to the end of this section. Be sure that you do not configure a twice NAT rule in this section that might match your VPN traffic, instead of matching the invisible rule. If VPN does not work due to NAT failure, consider adding twice NAT rules to section 3 instead.
View 2 Replies
View Related
Mar 25, 2013
when we add new switch to STP converged enviroment, switch flush the data from the data base.how to protect database from deleting the information
View 10 Replies
View Related
Feb 27, 2011
I recently installed a wireless printer and all seemed to work well until the next day. I am able to get on the Internet with my iPad but not my PC. I've tried winsock fix, ipconfig, netsh commands and other stuff but I can't connect to the Internet. When I tried to run ipconfig/all here's what I got:
An internal error occurred:The request is not supported.
View 13 Replies
View Related
Jun 5, 2012
I am researching on the behaviors of routers when MTU is increased beyond the MTU set in the routers. Also, when I use jumbo frames instead of normal MTU, how does it affect the network. So, what I plan to do is
LAN_A -- > blackbox --> WAN --------> WAN --> blackbox --> LAN_B
All the traffic coming from LAN_A will be of size 1500 Bytes or less. The blackbox in the center will add an overhead of 4 bytes, recalculate the CRC and transmit the packet on the WAN side. I wanted to know that:
1- if my LAN router and WAN router, both are set at 1500 MTU, then will WAN router drop the packet if it receives a packet greater than 1500B ?
2- If i keep my LAN side to 1500 MTU and I switch my WAN router to Jumbo frames, how will this configuration affect the complete network ? Will it work or not ?
3- I want to add the overhead on every packet coming in from LAN side, so, what options do I have to achieve this goal ?
PS. All types of traffic can come from LAN side.
View 2 Replies
View Related
Feb 8, 2011
I added the network printer cum scanner - cm1312, going to control panel >> add printer >> etc. etc. Now I can print. But there is no scanner installed. What I can do?
View 5 Replies
View Related
Jan 2, 2013
I added RAM to my HP Pavilion a6000n PC, and the only downside is that it no longer identifies the Netgear WNR1000v2-VC router as wireless.I run Windows 7 - have Comcast Internet and have an Arris TM722 modem.The modem and router were supplied by Comcast.I reloaded the cd that came with the router, everything appears to be on the hard drive, but the wireless is still not "enabled". The computer shows the connection as a local area connection, even though the modem and router are connected to each other and the pc.
View 2 Replies
View Related
Dec 27, 2011
I have a friend who asked me how he could stop his children accessing porn etc on their ipods etc that they pick up from a wireless router.Is it possible to route a wireless signal through a computer that has parental controls?
View 1 Replies
View Related
Jun 25, 2011
I am doing an evaluation of LMS 4.0. I have loaded the system on Windows and manually added my core 3750 switch into the system. Device availability is showing the device as available. However, the other pollers like link utilization, error count, etc. all show that there is no data. When I go into the poller config, the pollers for link utilization and errors show 0 devices associated and a status of "instance not found". The CPU and availability pollers show active with my one device added. I have verified the credentials and if I go into Inventory -> Port and module and select my 3750 I do get a list of all the interfaces and the descriptions so LMS is connecting to the switch and pulling data.
So how do I get the pollers for link utilization and errors to start populating data?
Second question, during install I did configure the software update section and it said there was an LMS 4.0.1 available which I told it to download. Now I have a psu_download directory and some more directories like cm, cmf, etc. but I don't see any file on what to do with them. What do I need to do to install the new package files that were downlaoded to psu_download?
View 4 Replies
View Related
Jul 31, 2012
I have run out of public facing IP addresses and I need more. Assuming I have been issued 1.1.1.0/24 and my new/additional range/subnet issued is 2.2.2/0/24 - Can I carry on with the same configuration on my ASA5510 and just add static NAT for new services in the 2.2.2.0/24 range.
i.e.existing config
route 0.0.0.0 0.0.0.0 1.1.1.254 (upstream ISP)
Interface outside ip address 1.1.1.1 255.255.255.0
NAT 2.2.2.1 to 10.1.2.3
or, assume my ISP will deliver 2.2.2.1 to my outside interface (1.1.1.1.1/24) and if my NAT is in place it will get delivered to 10.1.2.3 inside.
or, put another way I dont need change my set-up as I just static route to my ISP!
my real public IP is a /27 can I use my broadcast address (its a legit public IP address)?
i.e 1.2.3.0/27 = 1.2.3.1 to 1.2.3.31
Outside interface = 1.2.3.1/27
Can I use 1.2.3.31 and NAT it to an internal server?
View 3 Replies
View Related
Sep 30, 2012
Nice for those who want to see what it looks like:
Cisco Connect Cloud: [URL] EA6500: [URL] . And of course all other Linksys devices: [URL]
View 1 Replies
View Related
Jan 15, 2011
I have a really weird issue with my cisco catalyst 3560G.
-device: cisco catalyst 3560g
-ios: 12.2-53(SE) IP SERVICES
scenario: configured IPv6 iBGP link between this switch and a router. the router is announcing 1 (test) route. the switch sees the route properly, but doesn't add it to routing table (the route never gets to be "best path", although it should be).
View 15 Replies
View Related
Feb 26, 2012
I just added a wireless router netgear wgr614 and I secured it and it worked for one day and then after that no internet connection. I've rest and unplugged both the modem and the router and still nothing.
View 1 Replies
View Related
Dec 6, 2012
I have 3 computers wired to a Netgear R6300. Two of those computers (both running XP SP 3) I added new LAN Gigabit Cards (Tenda TEL9901G) . One recognized the card right away and had no issue connecting to the Internet (using this computer now). The other shows a 1.0 Gbps connection but I can not get any web pages to come up. I can access other computers and devices on the network without an issue on the computer that doesn't connect to the Internet.
If I type in the web address it says "Server Not Found." If I type in the IP address it will come up with the name of the site in the address bar but it still says "Server Not Found." I've tried several times to unplug the router and modem (Motorola Surfboard) and restart everything but the problem was still there. Also, I tried other Ethernet cables and no change. The LAN card drivers are up to date but I don't think the card is the issue since I swapped the new cards (to see if the card was the problem) and it does show a 1.0 Gbps connection. Also, tried uninstall/reinstall, disable/enable the card many times.I didn't change any setting in the router after installing the cards.Here is the ipconfig output:
Windows IP Configuration
Host Name . . . . . . . . . . . . : GATEWAY
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Mixed
IP Routing Enabled. . . . . . . . : Yes
WINS Proxy Enabled. . . . . . . . : No[code]......
View 6 Replies
View Related
Aug 4, 2011
I finally added wpa personnel security to my network. It worked on all computers until my sons xbox wouldn't connect so I disconnected the modem and router and reconnected. After this, the main computer at the router worked but 3 other laptops wouldn't connect to the network. I finally realized it wasn't broadcasting the ssid.All are working except I have an order computer running xp that previously worked-I hadn't checked it for a week-Ibut I just checked and it doesn't connect to the network. It finds the signal and I put the password in but it won't connect. I've deleted the connection and added it back with no luck.
View 1 Replies
View Related
Jul 20, 2011
I have Linksys WRT320N acting as AP with Mac filtering, yesterday I noticed that even not added Mac addresses can access the network!!The settings in Mac Filter page as following:EnablePrevent PCs listed below from accessing the wireless network.MAC 01: XX:XX:XX:XX:XX:XXMAC 02: XX:XX:XX:XX:XX:XX...when I changed it to "Permit PCs listed below to access the wireless network" no one is able to connect to the network!!!I think the AP is not accepting the MACs I added!I restart the router (Turning on and off) with no luck.Firmware Version: v1.0.03.
View 1 Replies
View Related
Sep 11, 2012
I have two Core 6509E SUP2T configued as VSS and has two 48 ports fiber blades. I have two 3750s, I have two gig on each 3750 port-channle to po1 and connected to both the core, one link to each core.Now, I was asked ot add two more links on each 3750 switch to make it a total of 4 gigs on each 3750s (all 4 gig ports/uplinks will be in used an dtwo links to core one an dtwo links to core 2).when i added two additional links on 3750s and bundled them to po1, I created another port channel on core and bundeled the additional two gigs on each core to accomodate for the two additional links (ports on core switches are not consequtives).
adding these two additional ports makes the 3750 switches flap between managemnet vlan and po1.now, i am not sure if I must have added the two additional links on the core to teh current port-channel or core!? I have created another port-channel on core to accomodate for this currently!?
View 26 Replies
View Related
Mar 12, 2012
Having an issue with two Cat 2940, they have fiber 100Base-TX. Added a new Cat switch (the second on the VLAN), the existing Cat switch drops the fiber connection.
View 6 Replies
View Related
May 30, 2013
We have a cisco 3750-48 port switch.We have a few SVI's configured and some static routes configured.I had created a new interface vlan and gave it an IP. I can ping the gateway.
Now I want to add a static route to go out that interface.when I add: ip route 10.x.x.x 255.255.255.0 10.52.10.1
it eccepts it (no errors) But, it does not show in the routing table nor in the config? How to add the static route to go out that vlan interface.
View 15 Replies
View Related
Dec 2, 2011
I'm running a couple of nexus 7000 to aggregate a building full of 3750Xs.In the past few weeks I have noticed that the vlans I added to the port-profile never got propagated.So I looked at port-profile sync information and here is what comes up: [code] Why the commands are getting cached?
View 3 Replies
View Related
Oct 11, 2010
Any way to test in a lab what would happen if a tech mistakingly added "switchport voice vlan XX" to a trunk port? I am try to do some RCA on an issue and this has been identified as a possible cause by one of my techs.
The config is Switch1------Switch2--------Switch3 Each interswitch connection is configured as a dot1q trunk with all vlans allowed. The link between switch2 and 3 is where switchport voice vlan 10 was added. Switch1 is a 3750 and 2/3 are 3560's.
View 8 Replies
View Related
Mar 7, 2012
I just added a X6704 card to our 6513 switch, and it is not working correctly. We are running 12.2(33)SXI5. [code]
View 5 Replies
View Related
Jun 1, 2012
Currently my home network is being switched via TrendNet TEGs80G unmanaged gig switches. I have been using them for about a year now with no issues. As my home network becomes more advanced, I recently just added a Cisco ASA5505, I am thinking about swapping those unmanaged devices, 4 of them, to managed. I was looking at the Cisco SG300-10 for upstairs, and a 16 port variant for my main core. These devices do not support full Cisco IOS cli, but they are manageable with a rich feature set nonetheless. My question is, should I swap the unmanaged devices with the more expensive Cisco devices, or just keep what works and save the money until I really need to spend it. As previously stated, my home LAN works just fine as it is, however my WiFi, NTV550s, server and workstations are all on the same network. Probably not the most secure but it is what it is without VLAN support.
View 11 Replies
View Related
Aug 15, 2011
I have installed my new E4200 and it works beautifully. I have several wirelss adapters and a few wired connections through powerline adapters. I also have a second VPN router attached to the 4200.I can see the wireless connected devices with the associated IP addresses. If I plug a laptop directly into the Cisco, I can of course see it.However, I can see none of the devices attatched to the powerline devices? I have a securty cam connected via the powerline and want to know the IP address. I checked with cisco technical support via chat and they said it is impossible. I have used 2 previous routers with the same configuration and can see all devices.
View 1 Replies
View Related
Oct 11, 2012
All of a sudden my laptop, android phone and blu ray player (all wireless devices) can't communicate with my wired devices (marantz receiver and samsung tv). Everything still connects to the internet independently but i can't for instance play music from my wireless laptop to my wired marantz receiver. I had no trouble with this last week and didn't change anything (that I'm aware of) I did get Verizon to switch out my router but it didn't solve anything. My wife's computer also cannot connect to wired devices. Lastly, if I connect my laptop with via ethernet cable it sees wired devices fine. I tried shutting off windows firewall but didn't work. I have no other firewall/virus software installed. I can ping to all devices (wired and wireless) from my laptop.
View 1 Replies
View Related
Jul 14, 2011
I have installed LMS. Then I have configured Default Credentional Set. Then start discovery with cdp and arp modules. LMS found my devices, 2 of them are reachable but other unreacheble. All snmp settings on the devices are the same. I test from LMS connectivity, it works great. Then checked snmp from pc (C:Program Files (x86)CSCOpxobjectsjtin) all tools snmpset and snmp walk works corretly and can get data. How make LMS to get data from devices ?
View 4 Replies
View Related
Sep 15, 2011
I've added several switches and one WLC to my new NCS Prime box. I don't see them in the display. If I try to readd one, it says it already exists. What am I missing?
View 0 Replies
View Related
