Cisco :: LMS 4 Devices Added But Not Shown In Inventory
Jul 1, 2011By reruning discovery with new seeds etc I have more devices discovered. Howeverr they are not shown in the inventory, only in the Device Discovery Summary however.
View 10 Replies
ADVERTISEMENT
Cisco :: Devices Not Shown In CS LMS 3.2
Oct 23, 2011LMS 3.2,the devices are not shown in the CS.
In CS Device management no devices are shown(0 devices).But devices are shown in DFM,RME and IPM.
Cisco :: LMS 4.0 No Devices Are Getting Added To DCR
Nov 13, 2011I am installing LMS 4.0 in my site newly I have nearly 1000 devices in network .When i had tried the autodiscovery mode using ping sweep method the devices are getting discovered but showing us unreacheable . All the devices are going under unreacheable no devices are getting added to the DCR .SNMP settings are configured correctly.
whether the autodiscovery will add the devices to DCR or i need to add the devices manually.As per my requierement i need to configure below things , is it possible to configure the same
1)LMS as SYSLOG server
2)LMS should send EMAIL notification if device goes down , interfaces goes down , memory / cpu goes high ,switch module goes down
3)Need to know if cisco releases new device packages how we will update to the cisco works .
Cisco :: LMS 4.0.1 Devices Not Added To DCR After Discovery?
May 30, 2011We have just installed LMS 4.0.1 and started to discover parts of the network. After the discovery process finished successfully - 100+ new devices were added to DCR message - I was able to see the devices by clicking on their number but when I go to Inventory-Add/Import/Manage Devices I cannot see any device in the Group that I created.If I restart the CiscoWorks Daemon Manager process the newly discovered devices are added to the custom Group. This seems like a bug as I had a LMS 4.0 evaluation installation a few months ago and device discovery was working fine meaning the devices were added immediately to the Inventory.
View 4 Replies View RelatedCisco :: LMS 3.01 - Inventory Failure On Various Devices
Nov 23, 2011We have several unknown devices within our inventory. When running an inventory report the message I get back is "No Credentials available".
For inventory checks is it just SNMP that is used or is it the standard credentials that are needed ?
I am planning to edit the credentials for the single device manually to see if this makes a difference. Our integration is with ACS and we have a machine account with admin priveleges.
Device Verification for the device states "Device Not reachable" for SNMP and SSH. There are no drops on any of our firewalls but snmpwalk does work from the command prompt from the LMS server.
Are there any further checks I can make for these 2 messages:
* "No Credentials available". * "Device Not reachable"
Cisco :: LMS 4.0 - Inventory Is Not Collected For Devices?
May 21, 2011I have been having problems getting devices into DFM once I enable fault management.I am now having issues with the basic LMS / RME I am getting the following issue:"No Device exists in LMS or Inventory is not collected for devices."I experienced this before and resolved by reapplying the licence.The issue has gone from - all devices discovered and added to LMS and DCR ok turned on Layer 2 Topology and Faults and then no devices appearing in DFM.after restarting the Daemon manger I have no devices in LMS. total device approx 1900 - standalone setup.
View 5 Replies View RelatedCisco :: ASR9K Series Devices Inventory Is Not Working
Apr 7, 2012Inventory in CiscoWorks with new devices ASR9K Series is not working. CW version: LMS3.2.1. Device: ASR-9006 AC Chassis. Credentials correct. Screenshot1: inventory request fail.
View 8 Replies View RelatedCisco :: 3750 - Devices Not Attempted In Inventory Collection
Sep 27, 2012When I do an Inventory Collection, the job doesn´t work with some devices and I have to restart the server. The job doesn´t fail but the log ICServer.log doesn´t got any information and it works for hours and hours and when it finally stops I can see that devices are not attempted.
I have done some succesfull Inventory Collections with Cisco 3750 switches and 805 routes. I have tried witch Cisco 2811 routers and 2950 and 2960 switches but it doesn´t work.
I have tried to update my LMS4.0.1 but it doesn´t find any actualization. However, in the Cisco download page there are some patches.
Cisco :: 2821 - Devices No Longer Appearing In LMS 4.0 Inventory
Jun 27, 2011The Cisco 2821 ISR's in our environment are listed under device management (Inventory>Device Administration>Add/Import/Manage Devices), but do not appear in the menus for inventory collection, archive synch, or net config. All are running IOS. No other routers or switches in the environment are displaying this symptom in LMS.
View 5 Replies View RelatedCisco :: Mac Address Not Shown?
Jun 9, 2011I've used Wireshark sniffer and one of the outputs was there was a loop, wireshark produced a mac address lets say its asdfgh so I looked it up on my core switch but there is no asdfgh on it's mac address table.
View 6 Replies View RelatedCisco AAA/Identity/Nac :: ACS V.5 Cannot Be Added As Secondary Via WAN
Aug 26, 2012i have planned a deployment with one acs in Europe working as primary, one acs in europe as secondary and one acs in USA as secondary also.
I can add one acs in europe to the deployment as secondary. When I try to add the acs in USA to the deployment - Nothing really works.
The status shown in the primary is offline (red) and status pending. It stays like this for hours. When I log in to the gui directly on the acs in USA, it still has status primary.
The two acs are transparently connected. There is WAN optimization (cisco waas) in between the two datacentres..
IP Configuration Address Not Shown?
Apr 12, 2011We tried some time ago getting David's XP notebook and his Win7 desktop to share the Internet connection that his desktop has via an ADSL modem and telephone line.We wanted to get the two PCs to communicate with each other via the Wi-Fi adaptor card in the desktop and the built-in Wi-Fi adaptor in the notebook and then to share the Internet connection. We had no success.Last weekend we tried to get David's Win7 laptop and Win7 desktop to share the Internet connection that his desktop has. No success again.At the moment each computer lists the other one in its "My Computer" page.he TrendNet Wi-Fi software in the desktop indicates that it has 100% signal strength from the laptop.Both computers are set to "Home" type networks.We can start a Home Group on either computer but cannot get the other one to join - an error is reported. We use the correct password when trying to join - the password displayed by the other computer when its Home Group is created.We cannot get the ICS service to stay started. After attempting to start it an error is reported that says "ICS service started and then stopped".
View 2 Replies View RelatedD-Link DIR-655 :: DIR-635 Not Shown On Website
Feb 17, 2011I have a DIR-635 and is rev B3 but this is not shown on the dlink website..
View 1 Replies View RelatedCisco :: Added New Server To PIX But Ports Not Open
Aug 22, 2012I am pretty new to Cisco - and I have a little 506E that I love. I got it working with my first scenario where I have one server that is my web, and e-mail server.I also opened the RDP port so I can remote into it. The IP's for the old server are internal 192.168.1.23 name ferbweb-external 71.12.111.219 name ferbwebpub. Now - I need to add another server in the exact same way with the same ports 80, 25, and 3389 open to the outside - IP's internal 192.168.1.31 name ferbmail and external 71.12.111.220 name ferbmailpub.I can get to all of these ports on the new server on the inside network - so that is not the problem.So, I went into the config, copied the statements for the old server, and changed them for the new server and added them to the config. I can still get to the old server from the outside fine, but cannot get to any ports on the the new server from the outside at all.I have done a lot of research, and cannot find what I am doing wrong.
View 6 Replies View RelatedCisco :: How Many 5508wlc Be Added To Mobility Group
Jun 23, 2011How many WLCs 5508 can you add to the mobility group?
View 1 Replies View RelatedCisco Switching/Routing :: 861 - Vlan Can't Be Added More Than Two
Dec 22, 2011I have the Cisco Router 861 whit the IOS c860-universalk9-mz.150-1.M7.bin. I have created a Vlan, but when I create a second vlan, I have this message: "Vlan can not be added. Maximum number of 2 vlan(s) in the database.
I need to add more than two vlan.
Cisco Firewall :: Invisible NAT Rules (twice) Added In 8.3 For VPN?
May 31, 2011Note If you configure VPN, the client dynamically adds invisible NAT rules to the end of this section. Be sure that you do not configure a twice NAT rule in this section that might match your VPN traffic, instead of matching the invisible rule. If VPN does not work due to NAT failure, consider adding twice NAT rules to section 3 instead.
View 2 Replies View RelatedBroadband :: LAN Connection Is Not Shown On Laptop?
Jan 13, 2011yesterday I did format my laptop (lenovo E43) but after that my LAN is not showing on my LT what I do I am using windows xp
View 1 Replies View RelatedLimited Access Shown On Wifi
Aug 21, 2011I am able to connect to my wifi but it shows LIMITED ACCESS and it show no internet access.I also tried to manually enter the same IP ADDRESS of another laptop by which i was able access Internet through the same wifi.
View 12 Replies View RelatedCan't Connect To Network But Shown On List?
Jul 5, 2011I've been "borrowing" a neighbor's wifi for the past 2 months. Everything was fine..a few hang ups here or there but other than that, no problem. The other night, my connection disconnected and i haven't been able to reconnect to the network for the past 24 hours.. The network is on the list of available networks. It's open, always has been. When i click it to connect, nothing happens. I've tried repairing the connection, turning off and on my radio signal
View 3 Replies View RelatedCisco :: LMS 4.2.1 Inventory Failed
Aug 6, 2012I can't inventory a 4507R + E / SUP7E Version 15.1.1 SG with the last version of LMS 4.2.1. Next, the extract of IC_Server.log.
[code]....
Protect Database When New Switch Added In STP
Mar 25, 2013when we add new switch to STP converged enviroment, switch flush the data from the data base.how to protect database from deleting the information
View 10 Replies View RelatedAdded Wireless Printer - Pc Won't Connect To Net
Feb 27, 2011I recently installed a wireless printer and all seemed to work well until the next day. I am able to get on the Internet with my iPad but not my PC. I've tried winsock fix, ipconfig, netsh commands and other stuff but I can't connect to the Internet. When I tried to run ipconfig/all here's what I got:
An internal error occurred:The request is not supported.
Cisco VPN :: 2811 Showing Crypto Map As Empty And No SA Shown
Nov 16, 2011I replaced old cisco router 2811 with new one 2921 , all works except crypto map VPNs routers can ping each other , ACLs are not applied to outbound interfaces show crypto isakmp sa is empty after i make same configuration on a new router 2921 config.
View 1 Replies View RelatedCisco :: 1242AG / Configure Wireless Not To Be Shown For Users But Used By Them?
May 19, 2011How can I configure the wireless not to be shown for users,but used by them? On a Cisco 1242AG I mean when someone do a wireless discovery not see my wireless name, but typing the name be able to connect it.
View 5 Replies View RelatedCisco :: Behavior Of Routers When Overhead Is Added On Packet?
Jun 5, 2012I am researching on the behaviors of routers when MTU is increased beyond the MTU set in the routers. Also, when I use jumbo frames instead of normal MTU, how does it affect the network. So, what I plan to do is
LAN_A -- > blackbox --> WAN --------> WAN --> blackbox --> LAN_B
All the traffic coming from LAN_A will be of size 1500 Bytes or less. The blackbox in the center will add an overhead of 4 bytes, recalculate the CRC and transmit the packet on the WAN side. I wanted to know that:
1- if my LAN router and WAN router, both are set at 1500 MTU, then will WAN router drop the packet if it receives a packet greater than 1500B ?
2- If i keep my LAN side to 1500 MTU and I switch my WAN router to Jumbo frames, how will this configuration affect the complete network ? Will it work or not ?
3- I want to add the overhead on every packet coming in from LAN side, so, what options do I have to achieve this goal ?
PS. All types of traffic can come from LAN side.
Security / Firewalls :: Router Is Shown Publicly?
Apr 2, 2012I've recently spotted my router's configuration page is shown publicly if they connect to external ip or a domain name I've set up to my own IP through a web browser (it's a game server)I see it as a security thread, that everybody can connect to my router's configuration page and want that down asap!
View 3 Replies View RelatedD-Link DAP-1522 :: DNS Server Not Shown In Static IP
Mar 16, 2012Under Advanced>DHCP Server, when I put in the Default DNS server of 192.168.0.1 and click save, it goes away. Meaning it doesn't show up anymore.
View 4 Replies View RelatedCisco :: LMS 4.0.1 Inventory Collection Failure
Feb 20, 2012After I upgrading all device packages, inventory collection failure to complete. All devices stuck on pending state and at the end of the job all devices are under not attempted and job result description ses " Timed out. Make shure that ICServer is running". I made sure that ICServer is running.
LMS runs on windows 2008 R2 server
Cisco :: LMS 4.0 Inventory Collection Is Failed
Oct 17, 2011I have Cisco Works LMS 4.0 on Win 2K8 64 bits on VMware EXs. I am facing issue with reference to Inventory Collection, my 10% devices (including Routers & Switches) Inventory collection is failed and give me error (Device sensed, but collection failed). I increase the SNMP timeout 10 sec, 30 sec, 60 sec and even 100 sec the result be the same.
View 1 Replies View RelatedCisco :: LMS 4.2.2 Times Out During Inventory Collection On VSS
Dec 12, 2012A customer of mine have 2 VSS systems for wich IC times out during collection when trying to read from flash on them. From the ICserver.log
[ Thu Dec 13 16:45:19 CET 2012 ],WARN ,[Thread-20],com.cisco.nm.rmeng.util.logger.XDILogger,67,com.cisco.nm.xms.xdi.pkgs.SharedInventoryCatIOS.FlashAGI_CISCO_FLASH_Mib,g$eval,70,com.cisco.nm.xms.xdi.pkgs.S
[Code].....
Cisco :: LMS 4.0.1 - Inventory Collection Failed?
Oct 5, 2011LMS 4.0.1 installed on Windows Server 2008 R2 Standard with SP1. Created Inventory collection job, but couple of hours later, it is failed with all devices Not Attempted. Increased SNMP timeout on 10 sec, started again for only 1 device - collection failed again. I am attaching pdshow and ICServer file.
View 6 Replies View RelatedAdded Network Printer But No Scanner Installed?
Feb 8, 2011I added the network printer cum scanner - cm1312, going to control panel >> add printer >> etc. etc. Now I can print. But there is no scanner installed. What I can do?
View 5 Replies View Related