Inventory in CiscoWorks with new devices ASR9K Series is not working. CW version: LMS3.2.1. Device: ASR-9006 AC Chassis. Credentials correct. Screenshot1: inventory request fail.
View 8 Replies
We have several unknown devices within our inventory. When running an inventory report the message I get back is "No Credentials available".
For inventory checks is it just SNMP that is used or is it the standard credentials that are needed ?
I am planning to edit the credentials for the single device manually to see if this makes a difference. Our integration is with ACS and we have a machine account with admin priveleges.
Device Verification for the device states "Device Not reachable" for SNMP and SSH. There are no drops on any of our firewalls but snmpwalk does work from the command prompt from the LMS server.
Are there any further checks I can make for these 2 messages:
* "No Credentials available". * "Device Not reachable"
I have been having problems getting devices into DFM once I enable fault management.I am now having issues with the basic LMS / RME I am getting the following issue:"No Device exists in LMS or Inventory is not collected for devices."I experienced this before and resolved by reapplying the licence.The issue has gone from - all devices discovered and added to LMS and DCR ok turned on Layer 2 Topology and Faults and then no devices appearing in DFM.after restarting the Daemon manger I have no devices in LMS. total device approx 1900 - standalone setup.
View 5 Replies View RelatedBy reruning discovery with new seeds etc I have more devices discovered. Howeverr they are not shown in the inventory, only in the Device Discovery Summary however.
View 10 Replies View RelatedWhen I do an Inventory Collection, the job doesn´t work with some devices and I have to restart the server. The job doesn´t fail but the log ICServer.log doesn´t got any information and it works for hours and hours and when it finally stops I can see that devices are not attempted.
I have done some succesfull Inventory Collections with Cisco 3750 switches and 805 routes. I have tried witch Cisco 2811 routers and 2950 and 2960 switches but it doesn´t work.
I have tried to update my LMS4.0.1 but it doesn´t find any actualization. However, in the Cisco download page there are some patches.
The Cisco 2821 ISR's in our environment are listed under device management (Inventory>Device Administration>Add/Import/Manage Devices), but do not appear in the menus for inventory collection, archive synch, or net config. All are running IOS. No other routers or switches in the environment are displaying this symptom in LMS.
View 5 Replies View RelatedI have a Cisco 887M router which I wish to restrict the devices allowed to be connected/allocated an IP address to two, and *only* two.
I can't, for the life of me, find out how to allow these two devices to connect to ANY port - I can configure a MAC restriction on a single port, but I don't know how to make it so that I can allow JUST these two devices to connect to any port in the 4 port switch/VLAN (VLAN 1 is used because the mongrel who set this up was lazy). I know the MAC addresses I want to allow
How I can do this? I *can* restrict any given port to the two MAC addresses - but if I try to add the MAC addresses to another port, they get removed from the initial one. I need to be able to have them connect to ANY port and work, but allow NOTHING else to work.
For those wondering, this is to counter a user who is utilising company resources for purposes not approved - and costing us quite a bit of money in the process.
I am currently deploying Cisco ASR9K BNG solution and it needs to be integrated with a Cisco ACS 3.3 (yes that old .. going to migrate to new product in the future) equipment. There are several specific attributes need that are not on the base config of the ACS 3.3 but it seems that i can configure them manually:In addition to supporting a set of predefined RADIUS vendors and vendor-specific attributes (VSAs), Cisco Secure ACS supports RADIUS vendors and VSAs that you define. Vendors you add must be IETF-compliant; therefore, all VSAs that you add must be sub-attributes of IETF RADIUS attribute number 26..This is from the ACS 3.3 configuration manual.I have never done this user defined VSAs.
View 1 Replies View RelatedI need to adapt a Cisco Catalyst switch configuration into a new ASR9000 router and I do not know how to configure trunks and access ports on an ASR9K router.
This is the configuration of the catalyst switch I want to replace.
interface GigabitEthernet1/0/1
description Access-Port -> SERVER
switchport access vlan 5
spanning-tree portfast
!
[code]....
Am I right? Or do I need to use the command “rewrite ingress tag pop 1 symmetric”on any of the interfaces o subinterfaces? Do I have to configure the command “encapsulation dot1q untagged“ on the GigabitEthernet0/0/0/0.5 subinterface?
I want to know, if it is possible to create multiples BGP AS Numbers on a ASR1K6 Router or ASR9K6 Router.
View 3 Replies View RelatedI have an installation of a new SMU on an ASR9k. Unfortunately, a previous install from a remote FTP source has stalled at 1%. The router is currently running v4.2.1, and the stalled installation was for a 4.2.0 SMU.
View 1 Replies View RelatedDoing a migration. During comparison of "show bgp nei x.x.x.x advertised-routes" between existing C7600 vs new ASR9K. Found that there were some r>i (RIB-Failure) route in C7600 doesn't flagged w/ r>i in ASR9K. Is it normal behaviour in ASR9K? How can I perserve r>i on ASR9K? Due to my IGP (e.g. AD etc) issue or ASR9K IOS-XR hidden config / default config issue?
View 5 Replies View RelatedI'm doing a large-scale snmpwalk against an ASR9k (with IOS-XR v4.2.0) running as a provider edge router (full bgp table) and pulling the full contents of the BGP route table. On other routers, this completes within my timeout window, but not on the ASR9k.Figuring that this has to do with CoPP rate-limits, I've adjusted the rate-limits to ridiculously high values.
But still, the walk doesn't complete in an acceptable amount of time. Manual snmpwalks display a rate slower than even 7600s, with occassional stutters. CPU on the box doesn't even register that anything extraordinary is going on (@ 2 - 3%), and "show lpts pifib hardware police location" shows that there are 0 drops against SNMP.I haven't turned yet - either some traffic shaping mechanism or some combination of process scheduling/priority with SNMP.
I am very new to high end Cisco devices.(like 7600/6500 or ASR9K).
Why do we log in on RP. What actions we can perform after logging-on RP (route processor) or Why they are required ? Cant we make those by normal router mode (router#) .
Our LMS DCR include more then 1200 devices, ( ASR 1000, CISCO 2600, 2800 advanced ip services IOS etc. )Everything is working well except the IP SLA device table is empty.I can not choose any device from this table.How can i import/add devices to this table/database automatically ?
View 2 Replies View Relatedi access points in our network.I want to connect with 3550 switch but access point is not working and getting the below error
controller port error.
IOS image --=c3550-i9q3l2-mz.121-20.EA1a.bin
Switch Model---WS-C3550-24PWR-SMI
I want to know ,this access point is supported on this switch ?
I have a Comcast Motorola Surfboard rental modem. It works fine, great speeds etc etc. It has no router or bridge support.
I use this modem to connect to the web on my ps3 and PC. What I have been doing is simply unplugging the ethernet cord from one device, and putting it in the other device to switch. But of course things can't be simple...
Every time I switch devices, the modem tries to reconnect and does a cycle where every time it only reaches the "Send" light. So I have to power cycle my modem and wait about a half hour before my connection resumes...
I read something about PPPoE, but Comcast doesn't even use it so that won't work.
I have a Comcast modem and a DIR-655 router. I finally got them to work together (it took some doing!) and now the router has stopped working with my Roku player and laptop. It still works fine with the desktop that's wired into it.
View 6 Replies View RelatedI have 10 new AIR-CAP3502I-A-K9 connected to a WS-C3750X-48PF-L switch. 8 of the APs power on and connect perfectly, but two are problematic. Both devices are granted power, but they never go past the stage of getting power from the switch. A look at POE shows: [code]
Where the AP that is not working is connected to Gi1/0/4. The interface shows down/down. I've tried shutting the interface, removing power, cdp etc.
Are there any other tricks you can think of to get it working or would you say that it's 2 faulty APs? I am not based at site unfortunately so I cannot console to the APs and check them out.
I'm running Windows 7 on my desktop, and I've had problems since yesterday with my pc. My Vista notebook, ipad3, ipod touch, android based phone and blackberry are all able to connect to the wifi, but my desktop is unable to connect to the wifi or ethernet. Things were working fine until yesterday, when I had to power cycle, after which the desktop connection stopped, though other devices are working fine. My ipconfig details are as follows:
Windows IP Configuration Host Name . . . . . . . . . . . . : DELL-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : reliancebroadband.co.in
[code]...
I need to apply DHCP snooping on 4500 series switches working as L2 in my Network. We have external DHCL Server in another location connected with 6500 series switch.
Running EIGRP Configured Voice & Data Vlan both
DHCP Server -------- 6509 switch<----------------------------------->6509 Switch -------- 4500 switch ----------------------------------------------------------Ip Phones.
(ving Redundant) (ving Redundant)
I need to know whether the configuration which I mentioned in scenario is enough for apply DHCP snooping in my network.
Region : Argentina
Model : TL-WR1043ND
Hardware Version : V1.8
Firmware Version : wr1043nv1_en_3_13_12_up_boot(121210)_UN_beta
ISP : fibertel argentina
The TP-Link managers surely have read the constant complaints about the performance of the WR1043ND, are innumerable and of all kinds, but especially, due to instability.There are two beta versions, but they are very unstable.I beg, TP-Link, keep us informed on the development of the new firmware.When I bought this router, I was hoping a correct performance.
I have a Linksys WRT54GS2 router, a PC (Windows XP) and a laptop (Windows 7 Ultimate 32 bit).I have been using this router for 3 months. I was able to use the internet on both devices simultaneously until now. But suddenly since yesterday it only works for one device at a time, not both.
If I connect to the router then I can access the internet only from the laptop. To use the internet from the PC, I have to power off the router, type in run "netsh int ip reset resetlog.txt", and restart the PC. But as the router is off, the internet is inaccessible on the laptop.
While router is on, the PC shows limited or no connectivity.
I tried reseting the router 2-3 times.
On the laptop it sometimes shows "IP address conflict has been detected", even though the IP addresses of the devices were not the same. The IP address of the PC shows 169.X.X.X (when the router is on), whereas the ISP's IP addresses start with 124.X.X.X.
I can't inventory a 4507R + E / SUP7E Version 15.1.1 SG with the last version of LMS 4.2.1. Next, the extract of IC_Server.log.
[code]....
After I upgrading all device packages, inventory collection failure to complete. All devices stuck on pending state and at the end of the job all devices are under not attempted and job result description ses " Timed out. Make shure that ICServer is running". I made sure that ICServer is running.
LMS runs on windows 2008 R2 server
I have Cisco Works LMS 4.0 on Win 2K8 64 bits on VMware EXs. I am facing issue with reference to Inventory Collection, my 10% devices (including Routers & Switches) Inventory collection is failed and give me error (Device sensed, but collection failed). I increase the SNMP timeout 10 sec, 30 sec, 60 sec and even 100 sec the result be the same.
View 1 Replies View RelatedA customer of mine have 2 VSS systems for wich IC times out during collection when trying to read from flash on them. From the ICserver.log
[ Thu Dec 13 16:45:19 CET 2012 ],WARN ,[Thread-20],com.cisco.nm.rmeng.util.logger.XDILogger,67,com.cisco.nm.xms.xdi.pkgs.SharedInventoryCatIOS.FlashAGI_CISCO_FLASH_Mib,g$eval,70,com.cisco.nm.xms.xdi.pkgs.S
[Code].....
LMS 4.0.1 installed on Windows Server 2008 R2 Standard with SP1. Created Inventory collection job, but couple of hours later, it is failed with all devices Not Attempted. Increased SNMP timeout on 10 sec, started again for only 1 device - collection failed again. I am attaching pdshow and ICServer file.
View 6 Replies View RelatedCan Controller 4400 series work with Aironet 3600 series?
View 5 Replies View Relatedwhy I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedWhat's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedMy Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedDoes AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View Related
