We have a Terminal Server through which everyone access their outlook. To avoid any impact on its performance, we have disabled the IE in it. Everyone access the terminal server using the Remote desktop.For the above mentioned setup, is there any way to make the weblinks in the remote machine to get open in the main machine? Main Machine or the Local Machine runs with Windows 7 OS.
View 3 RepliesI know that it's possible on the CSS to handle multiple incoming HTTP requests that terminate on the same IP address and port and balance them to various servers based on the url. For instance, I can set up URL at the same 192.168.35.12 address in DNS, and set up two different content rules:
content cats
vip address 192.168.35.12
port 80
url "//www.cats.com/*"
add server cats1
add server cats2
active
content dogs
vip 192.168.35.12
port 80
url "//www.dogs.com/*"
add server dogs1
add server dogs2
active.
Easy and straightforward.
But what if I want to add SSL handling for URl. I'm not sure how to create the ssl-proxy-list where one content rule (ip address/port) combination needs to pass through the ssl module and get matched with the proper ssl certificate.
Can this be done? Can one associate multiple certs and keys with a single ssl-server entry and a single ssl accelerator service? Or do I have to create multiple ssl-proxy-lists for cats and dogs and build multiple ssl services each referring to a unique ssl-proxy-list, and then use the url parameter in the https content rule to determine which ssl service (and therefore which key/cert pair) gets the traffic?
Since i used this new modem ruoter, on facebook game Cafe WORLD i can't send requests or gifts to neighbors/friends. when the window pops out there's no friend list. it's just a blank space. also when i click the share button only a blank page pops out. i tried it in 3 different pc here @ home in different browser but still had no luck...i tried it on my bf's place and it works so i guess there's a prob with my connection. and sometimes i have the internet access but i couldn't navigate in any website only for chatting.
View 3 Replies View RelatedWe want to mask part of the path prefix to hide development content: For example: the site(s) are: [URL]However we don't want anything with acme showing...so we would want the loadbalanced url to be: [URL] ...for requests and responses. I think this would be an http re-write request/response scenario?Is this possible to configure this on the ACE Device? We've got the load balance configuration down...not sure how to do this re-write type scenario?
View 2 Replies View RelatedMy current modem, the Arris DG860, when in router mode, handles uTorrents set to 1500 max connections fine, same with my FIOS Actiontec router at my work. However, I just bought a DLink DIR655 router (which I thought I researched properly to be great with torrents) and it crashes even with max connections set to 300 in my client.
Tempted to return the thing and get a better router, any great wireless router that has awesome range and can handle lots of torrenting?
I've noticed, that ACS 5.1 is writing .gpg archives for backups. I'm about to upgrade an evaluation system and the Installation and Upgrade Guide tells me to do a full backup and restore in order to upgrade an eval to a production system. [URL] (second note in section "Evaluating ACS 5.1)
Question: can the production system sucessfully decrypt the backup? According to my personal gpg it is CAST5 encrypted with one passphrase. Is this passphrase constant for all ACS 5.x?
I'm living in a house with 6 people on 2 floors, and the router isn't handling all the traffic well. I have an extra router that might be able to serve as an wireless access point, but from what I've been told that wouldn't solve anything if the problem was that the first router doesn't have the capacity for that much traffic. It's a 50+ dollar wireless N router though and fairly new (forgot the model number)
View 5 Replies View RelatedWe're testing the reference system shown in the figure below. System Description Four 2960 switches are used for transport;Equipment 1 and Equipment 2 exchange packets for synchronization;To reach synchronization Equipment 1 and 2 must exchange data with a very low jitter. 2960 Configuration details Four our test puprose, we're using 100Mbit/s ports (22 and 23) as trunk.In order to obtain minimum jitter We performed these configurations:We Enabled QoS;We Marked Synchronization packets with CoS 7 and DSCP 63;We marked other kind of traffic inserted in different ports) with CoS 0;We set "trust DSCP" on trunk ports;On the trunk ports we mapped traffic with CoS 7/DSCP 63 (and only this) on output queue 1;We enabled the expedite queue (priority-queue out). QuestionWith these settings we aim at forcing our synchronization packtes to precede other kind of traffic and go from Equipment 1 to Equipment 2 with minimum jitter.Unfortunately we experienced high jitter when both synchronization packets and other traffic are sent through the systems.
View 9 Replies View RelatedI have an SSL VPN set up on my ASA 5520 with a self signed cert. When I run the AnyConnect install on my desktop machine I have click through a few windows to accept the certificate. When I connect through the mobile client on Android, the connection goes right through without a prompt to import/choose/download a certificate. I'm able to connect but I'm wondering if the phone has actually recieved a certificate. I'm in the 'Advanced Connection Editor' screen and the certificate setting says "Automatic".
View 2 Replies View RelatedIs a 3750 sw capable of handling full routing tables and what can you recommend in a small mutihomed BGP router or switch capable of handling full routing tables?
View 2 Replies View RelatedEverytime I make a config change to one of the contexts on our ACE20, I get this message: Config Application in Progress. This command is queued to the system
If I run show download info, I get:
context : context1
Interface Download-status
--------------------------------------------------------------
187 In Progress
199 Pending
Regex download optimization status : Couldn't get status[TNRPC Timed out]
It eventually seems to complete, but it takes a very, very long time. We are running Version A2(3.5) [build 3.0(0)A2(3.5)].
I have IP television at home. I've connected windows box between the tv receiver and modem by using two network cards and brdiging them together. Now, when the request from th tv box comes to the computer, I want to be able to intercept that request and send new request from computer to modem, but request for different ip. So tv box would think that it is playing the requested ip, but in fact it would play the other one.
View 6 Replies View RelatedBasically my friend has a game server with a particular IP. But lately I don't seem to be able to even 'see' that server. Pinging the IP gets a timeout. I did a tracert on the IP and from the first hop onwards it gives me 3 stars followed by a 'Request Timed Out' until the 30'th hop.
View 15 Replies View RelatedI first noticed it in games, and decided to ping my router in CMD. I see the occasional "request timed out", and not sure how to fix it.My other computers connected to the network are working fine, and I've tried USB Wireless adapters in my laptop which work fine, which implies the problem lies with the inbuilt adapter itself.I've tried reformatting, and updating drivers, but to no avail.I thought maybe the adapter might just be faulty, but then I decided to test it on Linux. I pinged the router in the terminal and... it seemed to work fine. I thought maybe some background process in Windows might be doing something to cause the problem, so I started in safe mode (with networking)... still the problem remained.
View 5 Replies View RelatedReport run via Individual Web server URL’sThe report takes less than 20 minutes (average 15 minutes) to fetch and return the data. This is observed 9 out of 10 times.Report run via ACE Load Balanced URLThe report keeps on running for more than 20 minutes and never completes. The front end keeps showing report is running.The data in general when tested directly by running queries against the database (bypassing the platform) completes in 15-18 minutesThe network connectivity for each and every ports involved (Loadbalancer/Servers) have been throulgly checked.
View 6 Replies View Relatedrequest for registration - wont submit - nothing happaens
View 1 Replies View RelatedI am facing strange behavior in Windows 7 and Windows Vista.I have a client program in my PC and server program outside network.I can see that some time TCP WINDOWS SCALING working and some time not.In first Log after 3 way handshakes established I can see data transfer happening bocs from log I can see it is settings SCALING factor.
But for some cases where I see that connection happened but data transfer not happening (May be my network does not work without Scaling..) I can see my WINSOWS TCP stack has not set SCALING in SYN request.Hence in 2 nd log I can see "Scale factor not supported"...though I enabled SCALING in my WINDOW .
You can see in 2nd log :: [ Win=8192 ( ) = 8192 ] - not settings scaling factor some time.How to fix this issue so that Windows 7 / Vista always set SCALING in SYN request.
My TCP Settings :::
Receive-Side Scaling State : enabled
Chimney Offload State : automatic
NetDMA State : enabled[code].....
Request timeout on network connection
View 4 Replies View RelatedI tried to forward a new port on my Actiontec V1000H router. I was able to sign in without incident, but the moment I tried to begin navigating within pages, I would be greeted with a red screen reading '400 Bad Request - No request found' roughly 60% of the time. Usually refreshing the page a number of times would allow me to proceed, but because the Telus software for the V1000H cycles through so many pages when applying a new forwarded port to the firewall, it's almost statistically impossible to make it through.I have no issues with internet connectivity, and having this port forwarded isn't critical, but this problem is a real nuisance as it turns changing any router settings into a long, tedious, and sometimes downright impossible chore.
View 5 Replies View RelatedI have been doing a lot of research trying to find like an IT program to RDP for free to very little for personal use that is very easy to understand for the end user.An example of what I what I am speaking of, is if you deal with Verizon, or most major computer companies (Dell, etc) they can send you a URL or give you a code to use at a site, that basically lets them remote to your PC. It may require the user to install a small add on, or to allow some type of permissions, but doesn't require them to download huge programs or sign up for accounts.
I myself will create an account of course, and as I said even pay a small fee for a good program. But it's strictly for personal use and I am sure there is a good open source program I can use that I can just make a donation to.
I bought a Dlink DIR-815 the firmware version is 1.0 and not see any info in D-linlk support site inclusive the original firmware is not there. So I request to create a new forum topic for this hardware, I am replacing a DGL-4500 with this brand new model and we need other users have a good place to share info.
View 14 Replies View RelatedIn order to authenticate wireless users with EAP-TLS or PEAP-MSCHAPv2, what should I select the key length and digest to sign with? 2048 and SHA256 combination should work?
View 9 Replies View RelatedI have a strange issue where the first ping always times out, but the following goes through fine.I have Cisco877 and connection to the internet is fine. I connect a PC to one of the Fast Ether ports and I am able to ping the router without any issues. However, the moment I ping an external website [URL], the first ping request fails. after that the following request come through quickly.
View 24 Replies View RelatedAccording to traces collected in mt ACS SE 4.2, it would seem that the underlying software does not support the RADIUS Status-Server request. Is this request type is supported in version 5.*?
View 2 Replies View RelatedI have been unable to access a frequently used website (by me) for well over a week. Every time I attempt access I get this error message:
"Error 400 Bad Request
Bad Request
XID: 865749824
O: web
GN: ch-sc-bb-shield1
The web server is responding too slowly to service your request. Please try again later."
PC clone, 4GB, Windows 7 64-bit. Is it possible that my 64-bit version is at fault? I have had some problems with it since I upgraded form the 32-bit version.
I've had some issues with my internet connection lately. Occasionally I would have connection interruptions even when I am just browsing the web with no downloads in the background or anything like that.The strange thing is that connection fails right at the vey beginning - if I constanly ping the gateway, I will see that among the continous pings of 1ms or less, every once in a while I would have several "request time out" messages.My laptop is connected directly to the router with a 6 feet cable. I replaced the cable and it still happens.What I also noticed is that if I am online in the MMORG I am playing, I can stay online for long hours, however when I start browsing the web, I would get disconnected pretty soon. So I think somehow browsing (and downloading at high speeds, which is understandable) somehow triggers these timeouts. I dont know what to make out of it.
View 1 Replies View RelatedI'm working on a Dell Vostro 220s running Windows XP with an integrated NIC. It had a few hundred viruses on it and after removing them, I can't get an internet connection. The icon says connected with 0 packets sent and 0 packets received. DHCP is enabled and other computers on the network can connect to the internet. The drivers are installed and detected as working properly. I have rebooted also, with no luck. Ipconfig fails with the error "An Internal error occurred: The request is not supported."
View 8 Replies View RelatedI can access it at work and on other ISP's but not on my home wireless network. It won't work from any device on this network. I have reset my modem but that didn't work. It won't load and when I ping from command prompt, I get a 'Request Timed Out" message.
View 17 Replies View RelatedI have just bought a DIR-825 rev C1 stock firmware 3.0 (19 Jan 2012,) and I am pleased with its performance so far. However, I need to allow DHCP renewal request to pass through from all IP to UDP port 67 to UDP port 68; or else I will have to reboot DIR-825 every 24 hours (which is not fun ). My U-verse 2wire modem is a 3600HGV.
View 4 Replies View RelatedI am getting the message '400 bad request' whenever I try to backup the configuration or export a certificate under Certificate Management.
View 1 Replies View RelatedI have a Cisco 1801 Router, but whenever there is anything plugged into the integrated 8 port switch for example two computers, I cannot get them to ping each other. All of the ports are on the same vLAN.
I am a Cisco newbie, so sorry if this question/query is really basic. Is there anyway I can test the integrated switch to see if it is faulty.
I have a problem with my AnyConnect clients connecting to an AD network via a 5510. Anyconnect VPN clients provide AD plus a one time passcode to authenticate to the 5510. This works fine apart from 3 things:
1. Once the VPN session has been established the user is further prompted for AD credentials when accessing an AD share for the first time. Once they provide the credentials the share can be accessed. Should the AD credentials not be passed through when the VPN connection is established? Or is this by design? What makes me think it's not be design is the fact that this could be related to problem 2.
2. Group Policy Update (windows gpupdate) fails. This again suggests to me that the full client/server relationship is not fully in tact.
3. In order to get Outlook to connect to exchange I've had to change Outlooks security settings from Negotiate (which would naturally choose Keberors), to NTLM. Not sure if this is related or not.
Note: DNS is functioning with out any problems
Maybe the first 2 issues are by design, but I thought the whole idea behind the AnyConnect VPN was that the remote machine would function as if connected to the LAN?
I have an RV082 (running 2.0.0.19-tm) set up as the gateway to the Internet on my home LAN, and connect to it through several switches / hubs around my house. Randomly, and from various connections around the house (which are all plugged in to different ports of the RV082), a Web request will fail to load, giving a "Server not found" error in the browser. When I look at the log in the RV082, it says, "Connection Refused: Policy Violation".
It seems to be just blocking the DNS requests - everything else appears to go through normally. For example, I get the message "Looking up domain name.com" in the bottom corner of the browser and the request fails, displaying the Mozilla "Server not found" error page. When I click the "Try Again" button the page, it goes through just fine and everything works.
I don't have any services running behind the firewall, and do not use the VPN settings. Here are my current firewall settings:
Firewall : Enable