I am trying to host my own Minecraft server on my home desktop PC and I can't get my router to open port 25565 but it won't. I tried everything and I have concluded that my router's ports are all closed and can't open. I've tried using multiple DNS providers and DMZ but none worked. I have restarted my computer, restarted, rebooted, and reset my router and modem and still nothing. I have a Linksys e1000 router.
View 15 Replies
At first I tried to port forward 25565 on my D-Link Router account, but that didn't work for anyone trying to connect through the External IP.
People can connect locally over my network and I can connect to the game via localhost, but like I said, no friends from abroad.
I've checked my External IP and that doesn't work, I've tried resetting my router to factory default and then reinstalling the firmware for the model, that didn't work. I tried removing the firewall altogether, and also just allowing 25565, but that didn't work. I also got my friend to take their firewall off as well.
(Also, it should be known, when I'm port forwarding I'm allowing access, and have 25565 set in both TCP and UDP. I tested to see if the port was open on Open Port Check Tool, but it said it was closed (connection timed out) even though I had it forwarded)
I am trying to connect from the outside to a TCP server inside my lan that is listening on Port 25565. I am using a RV110W. I did the DMZ IP for it.
From the Lan I can establish a connection (even with my dynamic dns address). As I try it from the outside the server log tells me that a connection has been establishen but it shows the gateways IP. Afterwards it tells me the connection hase bin lost (Time out).
As I set Port forwarding I even cannot reach the server from the out side and lan.
I even did set up access rule WAN to Lan.
I've created some port forwards from my public IP (Dialer0) to our private LAN but only the 25565 port forward works. I've even added an any statement to the Nat source list Homenet_NAT. Full config attached. My Cisco router is an 877W. [Code]
View 6 Replies View Relatedhow do i open port 22 in my router
View 1 Replies View Relatedi have isp ip address i have opened port 9000,37777, 80 but when i check my port if there opened or not it keeps on say block?
View 1 Replies View Relatedrecently my brother has blocked some ports on our home router because he thinks i play too much video games. ( i actually dont play a lot ! ). He says there are alternative ways to make it work again and challenges me to figure out how to change the ports back to normal but he would not give me the access to the router, meaning i dont know the Login and password for it. Plus I am not allowed to reset the router to factory settings. For about three days I have been looking up ways to change the ports on my router through my computer but nothing has worked so far. I have a gaming tournament coming up and I really need to practice with my team but i cant get access to it.below is my system's information,
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit
Processor: AMD A6-3400M APU with Radeon(tm) HD Graphics, AMD64 Family 18 Model 1 Stepping 0
Processor Count: 4
RAM: 3560 Mb
Graphics Card: AMD Radeon(TM) HD 6520G, 512 Mb
Hard Drives: C: Total - 468745 MB, Free - 420932 MB;
Motherboard: ASUSTeK Computer Inc., K53Z
Antivirus: None
I have an issue/doubt regarding the configuration of a modem + router. The modem is a netopia-3000 (who care ) and the router is a netgear WGR614V9, The first has the address 192.168.1.1, the second 192.168.0.1 My pc in dhcp take the address from the router (192.168.0.x) and internet work, but if I set the ip manually 192.168.1.x it stop to work, why?
View 1 Replies View RelatedI want to port forward, so i can broadcast using icecast but it requires me to access my router. I follow the steps from Setting a Static IP Address in Windows 7 - PortForward.com but from step 4 where i have to access my router in my browser,i write my ip which is: 10.0.0.4 according to cmd, and i just get a "Oops! Google Chrome could not connect to 10.0.0.4" message.I have attached a picture showing info from my cmd. It's in danish but i don't think that should be a problem.
View 3 Replies View Relatedhow to open UDP port 16000 in my router Zyxel MAX 206 M1R...when i tried to start AGE OF EMPIRE 2 THE AGE OF THE KING in gameranger it says that my UDP port 16000 is not opened...so i am trying to open it..
View 2 Replies View RelatedA external scan has reviled that I have an open port. For security reasons I want to close it. I do know the port number.
View 7 Replies View Relatedi want to open portforward to utorrent in arouter but i cant open the addres of the router lookand when i go to local area connection status /status/detailsi found number of ip but there is no gateway i take whole ip and put them in browser and its dont open but the last friday i wake up in 3am run cmd and put ipconfigi found the gateway 192.168.2.45put it it in browser its open want username and pass i know them but i see lets doit next day going to bed next day the gate way reverse to the stupid gateway in in the pic i cant use aprogram to open port as i cant knowing my router mode
View 1 Replies View RelatedI have D-Link's DSL-2730U modem/router. I've enabled the router's firewall and disabled TR-069 (putting in some dummy ACS URL and login credentials as well). However port scans show 30005 as open. I believe this is used by the TR-069 client. How do I definitively filter this port?
View 9 Replies View RelatedI want to know how could I configure a Router Cisco DDR2201v1 for watching my CCTV System from anywhere with a internet connection. I already try to open a port in the NAT virtual server configuration but it didn't work.
View 1 Replies View RelatedHow to open port 443 on my wireless router model WRT54G3G-AT? For a secure business connection. Plese don't give me a link to follow, I've tried that one.
View 1 Replies View RelatedI'm using Cisco Connect Cloud to connect to my E4200 router. I wish to open my NAT type as currently its moderate on all games.Where the hell is the area to add the port ranges?? Is it even an option on the new connect cloud? If it is, it doesn't make it very easy to find. Would be allot easier if you had a tab/app for "Gaming/Applications" like you did previously.
View 1 Replies View RelatedHave a E4200 with version 1.0.04 firmware.Been trying to open 9000 to access my buffalo media server remotely. Have set up both Single Port and Port Range Forwarding for port 9000.On trying to access media server, get message " could not connect to xxx.xxx.x.xxx:9000"Using online Open Ports Checkers shows this port is closed.
- Tried disabling all firewalls.
- tried range of ports
- Enabled/Disabled UPnP
- tried cisco & buffalo tech support
I purchased a Cisco 1750 router. I was able to access my cameras from my iPhone before I setup this router. Now I can get my cameras to work. I need to setup port 80. I followed the instructions on how to do it but for some reason the cameras do not work on my iPhone.
View 1 Replies View RelatedI need to open port 4001 on my router for someone to have access. I need to do this thru GUI. Cisco ASA 5505
View 5 Replies View RelatedI own an E4200 and my wife and I use Goodreader on our ipads at home. To add docs to goodreader we need to connect to the ipads ip on port 8080 but the E4200 is blocking all traffic for it. How can I open port 8080 for our 2 ipads?
View 1 Replies View Related I have 4 public IPs on Router 3845 interface FastEthernet 0/0/1. IP as below.
50.200.2.2
50.200.2.3 secondary
50.200.2.4 secondary
50.200.2.5 secondary
I wan to allow ports 80 to 90 on 50.200.2.3 for my webserver (192.168.10.50)
I am having a NAT issue with my two xboxes. The router is an e1000 v2.1 firmware 2.1.02. One xbox is wired into the router and the other has a wireless adapter. The wireless xbox gets open nat automatically, while the wired one's nat is strict. If i mess with DMZ and turn UPnP off i can get the wired to be open but the wireless one to be strict. Also port forwarding does not seem to work because only one or the other xboxes will get an open NAT. I do have the the correct ports in the port triggering section set to on but that does not seem like it works.
View 5 Replies View RelatedI have only recently noticed a HUGE decrease in my Utorrent speeds, so i thought i would have a gander and lo and behold.apparently the port Utorrent uses wasn't open. Now, i have tried about 10 different port numbers, made sure Utorrent is being accepted by Norton 360 Firewall,followed complicated directions to (i think) foward ports, and also follow directions to open a specific port.Nothing has worked so far, Utorrent still comes back with a port closed error.
View 1 Replies View RelatedI have the port numbers but do not know how to proceed from there. Router is a WRT160N V2.
View 9 Replies View RelatedWhat is open port 49153 used for and how do I close it and any other open port that I don't know they got opened in the first place.
View 1 Replies View RelatedMy friend is trying to open port 88 and it says this specific message "The specified ports are being used by other configurations".I did a netstat, netstat -a, and another netstat that i forgot and we could find anything on his computer using port 88.His router is a Netgear wndr3400.
View 5 Replies View RelatedI have an IP camera (foscam). It's connected to my wireless router. My router is connected to my motorola cable modem. My isp is Cox.I want to be able to view this camera from outside (ie: when I'm at work) by going to http://(my real ip) : (port). Port that I use is 88. I can't seem to do this.
First I set the port 88 to the camera's config. I can see the camera when I'm at home (going to 192.168.1.106:88). Reading the manual, I need to forward the port 88. So I go to my linksys wireless router 192.168.1.1 and single-port forward 88 UDP TCP (both) to 192.168.1.106.This doesn't solve the problem.I go to Open Port Check Tool and put in port 88 and it says I could not see your service on (my real ip) on port (88)
I have a say 'server', with win xp running on it. I want to open a port on the system so that that computer can be accessed within the network domain. for example when i open an internet explorer browser and type in [URL], i need to be able to connect to the /mls.net/eclispe.aspx present. so for that i have to be able to open a port
View 1 Replies View Relatedi have 3g mobile dvr, put a sim card directly into it and it gets an ip address and you should be able to view it remotely but i cannot connect. i can ping the ip no problem and i checked that the port the dvr uses (9000) was also open on that ip and i used a locator to trace the ip and it pinpoints the ip to my isp's base so why i cannot connect to it
View 2 Replies View RelatedI've been trying to set up a customers security camera's for remote viewing. He has a HP running Vista, a netgear grt614 vs10 router, and a static IP address through Verizon. My problem is this. I set up port forwarding for port 80. All seems to work well sometimes and I can connect to his DVR no problem. Then other times I can't connect at all. I'll run a port checker and it will tell me port 80 is closed. Is it possible that Verizon will off and on block inbound port 80? I seem to only be able to connect during buisness hours. Is it possible that his PC needs to be on for the port to be open. The DVR is the server which is always on and the router is always on. I don't know why the computer would have to be on.
View 6 Replies View RelatedI've been trying to open ports to start a server on some games that I play.I used a guide that shows you how to set up the server and open up the port, but I can't get it to work.I've tried making an exception in my firewall,but that didn't work, so I tried completely disabling my firewalls. Nothing. I've gone into my router settings and opening a port this way: But it still doesn't open it up. This is what I'm using to check it.In fact, NONE of the ports are open it seems? No matter what port I try to type in on the port checker, it always gives me that same error.
-Both?
-Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:Usersack>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : FellowShip[code]....
Who is your Internet Service Provider (ISP)?
-Comcast
What type of Broadband connection are you using?
-Cable
What is the exact Make and Model of your Modem, Router or Modem/Router Combo?
-Router is WNR2000v3, Modem is SMCD3GNV (One I'm renting from Comcast)
What is the Name of the Anti-Virus, Security or Firewall Software installed from the problematic computer?
-Avast! Antivirus and Default Windows Firewall
how to find open udp ports of isp i want it for internet purpose
View 3 Replies View Relatedtell me the most advanced the udp and tcp open port scanner of my network ?
View 2 Replies View Related
