Can't Obtain IP Address From Wireless Access Point After Few Days Of Uptime?
Dec 12, 2012
My set up is a 2wire router that connects to the internet, with an ethernet power plug connected to it. Over the other side of the house, I have the other ethernet power plug connected, with a Netgear router in access point mode.The main router is on 192.168.1.1, and the access point is on 192.168.1.3. The DCHP server is enabled on the main router with range 192.168.64 to 192.168.1.253. The access point has the DCHP server turned off. The routers have the same APN and security (WPA2-PSK).Also, the wireless channels don't overlap, channel 1 and 11.Now to my problem:The internet always works fine for a few days when the routers are turned on. But at some point between 1 to 3 days later, every computer can't obtain an IP address while connected to the access point. But all computers can connect to the main router (i.e. when closer to the main router than the access point), and then go near the access point and it keeps the connection. If I reboot the access point, then everything works again for a few days.
View 3 Replies
ADVERTISEMENT
Dec 14, 2012
I bought a Linksys WAP610N today, i placed it so i could get a signal where i can't normally.
The thing is i configured it correctly, well at least i think, i can see it on my wireless network, with a good signal, but on my Android tablet (Google Nexus 7), it can't get past the "Obtaining IP address".
I called the technical support, the person there tried to assist me for about 1 hour, we tried different settings, we upgraded firmware from 1.0.01 to 1.0.04, but it didn't worked. Now he said someone will call me tomorrow during the afternoon.
My router isn't Linksys, it's a Netgear, i don't have wireless problem when i connect my tablets or any other wireless device on it, it's just that i bought this WAP610N to have the signal in my bedroom, where i don't get any signal normally.
View 7 Replies
View Related
Aug 22, 2012
I'm probably overlooking something very simple but is there a command to show the uptime of a router interface in days,hours,minutes?
View 3 Replies
View Related
Jan 23, 2011
I've had the adapter for a while now, successfully running on XP SP3 with the linksys software. I could see networks, connect to them with WPA security and get an IP address. I recently tried uninstalling the software, then connecting the adapter to install only the drivers and let windows manage it. Since then, I haven't been able to acquire an IP address. It can see the SSID and connect to it, but continually tries to acquire an IP address. I've tried this with different SSIDs at work and home...same result. I've tried uninstalling the driver from device manager, but every time I restart and connect the adapter, windows recognizes the adapter. I probably made matters worse by connecting another adapter to it, in an attempt to work around the problem. That is a USB adapter, WUSB600N. Tried the same thing, but continually tries to acquire an IP address.
View 2 Replies
View Related
Sep 26, 2011
I tried many times to connect my ps3 to the internet/playstation network so far no luck. The router I'm using is a linksys WRT54G v 2.00.8. I have no problem using my WII, PSP, or computer to go online but my ps3 cannot connect to the internet.url...The errors I might sometimes get is "failed to obtain IP adress" and most of the time I get something with unable to connect to internet server when I am able to get the IP address
I was thinking maybe I shold reset my router to default settings but I'm not sure what's the way to do that or update the router? This problem also has been happening for a week now. In the previous weeks I could easily connect to the internet with no problems and all of a sudden I cannot connect anymore and this has happened a few times already in the past where I am unable to connect to the internet with my ps3 for a few days to a week.
View 1 Replies
View Related
Feb 6, 2012
I'm trying to connect my Xbox 360 to Live by bridging my computer's wireless connection. I've done this before for a friend in a different city and it worked fine, and I felt very proud of myself for doing so. However when I try to connect here, the modem won't assign my Xbox an IP address. I've been into ipconfig/all and tried to manually assign the same IP address to the Xbox but to no avail. Same deal with the alternate MAC address option.
To speed things along here's the readout from my ipconfig/all:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersSamsung>ipconfig/all
[Code].....
View 2 Replies
View Related
Oct 9, 2011
When I change my WRT320N routers IP address to use it as an access point only and bring it in the IP range of my ccombined modem/router I'm not able to view the setup page via the new IP address. I have tried to change the IP from the default 192.168.1.1 to 192.168.178.2. After changing and applying the changes I restarted the router and tried to access the router via the new address. This was not possible am I doing something wrong or did I forgot something?
View 8 Replies
View Related
Mar 1, 2012
I have a wrt54gs v7 and a wap54g v3.1. Both have latest firmware on them. I set the access point to act as a repeater and entered the mac address from the router (It said to use the lan mac address. is that right?). I have them set on same subnet with static ip addresses. They have same wireless ssid and password with one using channel 10 and the other using channel 2. I can receive an ip address from the router and connect to internet. I cannot get an ip address from the access point. I tried a static ip on the computer and it will connect, but I don't have internet. Am I missing something in the setup? Can this access point act as a repeater for this router?
View 3 Replies
View Related
Dec 30, 2012
we have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.
View 17 Replies
View Related
Mar 12, 2012
Currently i have multiple computers that are connect via lan with ip addresses(static) that are connected to a cisco router. My question to you, how do you assign more ip addresses to computers on the lan.
View 2 Replies
View Related
May 11, 2011
I coulden't visit any websites and it gave me an "error 105" something. So i tried connecting my other comp to the internet cabel with the same result. So i tried to find a solution on the web (wierless internet still worked) and stumbeld upon a similar problem were the answer was to manually fill in an adress in the "internet protocol version 4" properties in the "local area connection" properties. I then noticed that i dident have the "Obtain DNS server address" set to automatically and that the other manual boxes were empty. I then turned the auto on an i had access to internet. Is this safe? Cause i read somewere that DNS server addresess were provided by the company that provide you your internet service, and that you can be redericted to a fake website that can get a hold of your account information on it
View 1 Replies
View Related
Oct 19, 2011
Anyway, I have an hp desktop pc, running windows 7, with high speed cable connection.. Im attempting to obtain a new ip address.. but when I go to command prompt, and type in ipconfig/release, I get an error telling me that "No operation can be performed on Local Area Connection 2 while it has its media disconnected"
View 1 Replies
View Related
Feb 7, 2011
I have a netgear wireless router, not sure on the model but can find out if required. My xbox360 is hard wired to the router and my Laptop is connected wirelessly to the router using the internal wireless connection on the laptop. The other half has a laptop too, for some reason her will not connect wirelessly, just gets stuck on a constant loop of ''aquiring ip address'' and does not get past this point. Laptop works if hard wired to the router. how do i get ip address to assign.
View 1 Replies
View Related
Aug 28, 2012
I have a Lexmark Professional X7675 that will not connect to my wireless network saying "unable to obtain IP address". This printer was previously connected to the wireless network with no issues. I did a reinstall on my computer and a reset of the printer network settings but still it will not connect to the wireless. The SSID and the WPA are both correct.
View 1 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Sep 22, 2011
I just got the motorola droid 3, my first android device. I'm trying to figure out how to get my device to connect to my network as it won't obtain the IP address.I have a Motorola Surfboard SBV5120 Modem and a Microsoft MN-700 router. I just switched from the Palm Pre Plus which connected perfectly to this network, the network is unsecured and has 2 pc's and a 360 running on it. I was able to connect to my friend's wireless network fine at his house.
View 9 Replies
View Related
Sep 10, 2012
My Fujitsu Siemens AMILO XI-1554 RTL8169/8110 ethernet will not obtain IP address on any other LAN, except my home network. The adapter is set to obtain IP address automatically. I have updated the drivers using the Update Driver option on Windows 7 Ultimate 32-bit.
View 1 Replies
View Related
Jun 17, 2011
I have an Avaya IP Phone for work. This has been tested at work and works as expected. After the IP Phone boots it's able to obtain an IP address from work. At home when I plug the IP phone into my DIR-655 router, it's unable to obtain an IP address. Other network devices are able to obtain an IP address, for example any computer or laptop. Also my wireless works with no issues expect for the IP phone. I've already done some searching and found other users with the same issue but I haven't been able to find a solution other than setting a static IP address. I'm curious why this relatively new router won't work with an IP phone. I've played with some of the router settings but it didn't make a difference. Any work around to get the DHCP to work? I'm running the latest firmware for my router: 1.35A Hardware Versions: A4.
View 9 Replies
View Related
Apr 8, 2013
I have installed about 2 days ago one Cisco WCS 2504 and 11 APs. Everything is doing well regarding to WEP authentication. But I have a Radius Server that is alson running with some issues on wireless:
- Unless I open network settings and click connect on that config I cannot obtain a valid IP Address;
- Roaming is not working also;
View 6 Replies
View Related
Dec 20, 2011
what application/service is sending out net bios broadcasts on a network segment the requests are for machines that no longer are on the network but something is trying to obtain there ip address as they are not in dns any more i am assuming this is why they are resorting to netbios broadcasts i need to some how isolate what application or service is trying to find out.
View 9 Replies
View Related
Mar 29, 2012
I would like to share one problem with WLC 5508 . we added a new virtual interface on the WLC. One new SSID is associated with this interface.
We created a ACL for this interface to restrict the access via WIFI to certian services. It´s not correct that everything works fine because the change were not applied. [code]
The changes of the ACL are applied on the fly, but for reason we don´t know, the clients don´t get a DHCP IP-Address (after changing the ACL) until the Controller is rebooted.
View 2 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Sep 30, 2011
how to check the mac address of a existing access point that i want to connect to the wired network.
View 1 Replies
View Related
Nov 5, 2012
I am trying to connect my WDTV Live to my desktop PC, and I connect to the net through a wireless connection to my router. Because its in the other room, I can't connect my WDTV Live to the router without running cable along the floor. Having said that, its not far away from my desktop PC, so I'm trying to connect them directly via cable. The problem is that my WD keeps telling me that it can't obtain an IP address and I don't know how to fix it or what values to put in.I've tried power cycling, manually setting an IP address (192.168.0.5), using different cables, all with no success[CODE]
View 1 Replies
View Related
Nov 9, 2012
I have recently bought a Asus Eee PC with Windows 7 starter.It will connect ok to public Wifi (i.e. at the Qantas lounge) but will not connect to my home Wifi network - Netcomm N150 Router. The two other computer at home (running full versions of Windows 7) work fine over this network.When I look at the Station list in the Router's interface the MAC address for the new laptop appears but it has no IP address. [code] Have tried the obvious things like power cycling.
View 13 Replies
View Related
Dec 14, 2011
we have Core-Siwtch 4503 in the main building which is connected to another Core 4503-E in another building ,, now our PCs connected to the 4503-E ,,, any XP M/C can pick an Dhcp-ip but and M/C run Win.7 Cannot !!
action taken :
1st we try to connect our win 7 pc in the node which was connected to xp M/C ,, and it didnot take ip from the DHCP . ,, 2
2nd we ensure from the core-switch configuration and its normal with no mistake
3rd trying to use tool from Microsoft Fix-it Center whih name is ( Microsoftfixit 50475 ) which is just .msi file but the problem face us is that this tool donnot accept to run on win 7 cause its made for vista .
4th after some researchs we notic that there is some modifications have to be performed on registery by disabling the dhcp broadcast flag we did it but nothing change yet
5th now we are waiting to perform another action which is Disable the IP Helper service in win 7
View 6 Replies
View Related
May 17, 2011
To put it simply, my parents live far enough in the middle of nowhere that they have no access to high speed internet. Of course, there are always wireless solutions, but the options around here are pathetic and comparable to dialup. They were content with this; I moved back in with them for the time being and am not.y solution has been to dump just shy of $1,000 into a point-to-point wireless bridge setup that claims to have a range of 5 miles non-line-of-sight. I have one antenna set up four miles away on top of a building that has high speed internet.Unfortunately, I was a stupid fool and set that end up without enabling security, thinking that it wasn't a big deal. Nobody in that town has a mind for anything but farming and drinking. That was my mistake. Some asshole set a password and forced me to do a factory reset on the access point and now I can find no IP address. It's like it only reset halfway to factory defaults or something
View 6 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Apr 14, 2013
I have two ethernet cards (from same equipment) that arent acquiring IP Address after instalation of WLC 2504.I dont want (yet) to disable DHCP proxy on WLC.
*DHCP Socket Task: Apr 15 18:49:04.219: 00:0a:95:XX DHCP received op BOOTREQUEST (1) (len 556,vlan 0, port 1, encap 0xec00)
*DHCP Socket Task: Apr 15 18:49:04.219: 00:0a:95:XX DHCP dropping packet (no mscb) found - (giaddr 0.0.0.0, pktInfo->srcPort 68, op: 'BOOTREQUEST')
*DHCP Socket Task: Apr 15 18:49:07.218: 00:0a:95:XX DHCP received op BOOTREQUEST (1) (len 556,vlan 0, port 1, encap 0xec00)
*DHCP Socket Task: Apr 15 18:49:07.218: 00:0a:95:XX DHCP dropping packet (no mscb) found - (giaddr 0.0.0.0, pktInfo->srcPort 68, op: 'BOOTREQUEST')
[code].....
View 6 Replies
View Related
Feb 22, 2012
Trying to setup secure net but when I type in the router IP Address, it shows Netgear, Type in printer IP address and it shows Linksys. How can I access my Linksys to make changes? I believe the Netgear shown is Comcast modem...
View 9 Replies
View Related
Jan 22, 2013
I have a strange behavior between a WLC 5508 (version 7.0.116.0) and NEXUS7010.
WLC
The WLC is configured in DHCP Bridging Mode (it sends DHCP requests without change)
Nexus
The VLAN interface is configured as follows
interface Vlan501
ip access-group acl-int-vlan501-in-1 in
no ip redirects
ip address 10.12.56.4/21
ip ospf network broadcast
ip router ospf 100 area 10.23.0.0
hsrp 51
Clients can not obtain an IP address intermittently. If I deactivates the ACL when the problem appears(when the client can not obtain an IP@) the probleme is resolved
Note: Before the WLC was connected to Catalyst 6500 and worked properly for 2 years (with same configuration)
I saw this note about differences between DHCP relay on the NEXUS7000/NXOS an Ip helper one the 6500/IOS URL. Do you think the problem may come from the DHCP relay or ACL on the NEXUS.
View 2 Replies
View Related
Feb 20, 2013
2 days ago, my laptop was connected to my router and working fine. But it then randomly disconnected and haven't been able to connect back since. I am using an ethernet cable to access the internet, and have tried many ways to try and resolve the issue but nothing is working.
I have a Dell L501x (Win 7 64-bit) with the Intel Centrino 1000 BGN wifi card. I have restarted the router and modem and disconnected all devices and tried reconnecting, but to no avail. I have tried updating the drivers, system restoring and using safe mode (with network) but nothing works. The modem and router are working fine as other devices connect and access the internet, it is just my laptop that cannot.
I am sure it is not a hardware issue as the card detects all the surrounding networks. The troubleshooter only says "An administrator profile failed to obtain an IP address from the DHCP server.
View 10 Replies
View Related
Aug 24, 2011
I just got a new RV042. V3 Hw.For setup and testing before putting it in action, I've attached the WAN1 side to my internal network.But it fails to get an IP address, and the log shows: "Infinite lease time, exiting".My current router on the LAN is giving out DHCP addresses with 3 hour lease time, and I've checked with the PC's on the LAN that this is correct.The routers DHCP status shows that the lease time for the RV042 is 3 hours ahead.So why does the RV042 complain about long lease time ?Is there a way to avoid this error from occurring?
I have tried to change from 'Gateway' to 'Router', but this does not change anything.Also tried a factory reset, with no luck.Fw is upgraded to the latest 4.0.4.02
View 2 Replies
View Related
