Cannot Get 8 Port Workgroup Hub To Connect Multiple PCs To Internet
Apr 12, 2013
I am trying to get multiple PCs in a computer lab connected to the internet at the same time. There is an ethernet jack and right now the cord there is going into the linksys 8 port workgroub hub and then separate ethernet cords are wired from the hub out to each computer. But, this set up only allows the PC that is turned on first to connect to the internet. Am I using the hub wrong? Do I need another piece of equipment? The lab was set up like this when I arrived, but it is not working (I am thinking it did at some time).
View 3 Replies
ADVERTISEMENT
Jul 17, 2011
I have a few laptops at home and one desktop. I also have a work laptop which I carry to work every day. I have a lan at home. The computers are connected through a wireless router though my pc is connected through a lan cable. We are able to share files and content.
I sometimes connect my office laptop at home. Though the laptop connects to the network but I am unable to transfer or share files to other computers running Windows Vista/7. After a bit of research I figured this is because the workgroup name of my office laptop is different than the systems at home. I dont want to change the workgroup name of my office laptop as it will create problems at work.
How can I connected my office laptop to the network and transfer files if the workgroup name is different? It does show names of computers on network but when I try to connect a username & password box pops up.
View 6 Replies
View Related
Jan 18, 2011
First , I have installed the router and modem correctly , and i connected it to the switch , So the other devices connected to the internet but not connected to the workgroup so i can't share the files between the PC's ? Modem >>> Router >>> Switch >>> PC's
View 1 Replies
View Related
Sep 29, 2011
I have networked three computer using lan through wired switch. I have one net setter with me. And i have connected it with my one computer.And now how can i get internet on others computers.
View 1 Replies
View Related
Jan 31, 2012
We have a new router (D Link) at offices which is fixed with LAN wall points on different places , we want to use it .I connected computers to the LAN points with regular lan cables , it gives me the alert (connected) but no bytes received .I tried to ipconfig an here's what i got :Windows IP ConfigurationEthernet adapter Local Area Connection 2[CODE]
View 1 Replies
View Related
Jan 11, 2013
I can't print from the printer which is in the workgroup and connect to a computer with different OS from mine.
View 1 Replies
View Related
Feb 5, 2013
I am using a (Windows 7 OS) machine from work (that has a domain name set) at home and want to connect it to my home's workgroup so that I can access files on two other computers currently in the workgroup: one running windows 7 the other xp.
View 1 Replies
View Related
Jul 25, 2012
I am trying to connect my file server to my desktop and laptop through a workgroup, however while my Laptop and desktop recognize each other, they will not recognize the file server. I have tried what I can including setting firewall exceptions and even disabling it and nothing will change. Both the file server and desktop run Windows XP SP3 while the laptop runs Windows 7 Home Premium. the file server is connected to a 5-port router which is then connected to a 10-port hub that is connected to the gateway, while the laptop and desktop are connected to a different 5-port router which is connected to the same 10-port hub. I am saying thing also because I think it is a hardware problem since the laptop/desktop can connect perfectly as they are on the same router.
View 4 Replies
View Related
Dec 30, 2011
I have a Windows 7 Laptop that need to be able to join a Home Workgroup as well as an office Workgroup. How!
View 1 Replies
View Related
Mar 23, 2012
My son connects his xbox360 to his laptop that uses a wireless access to the router. My husband and i both have a laptop and when we try to log on to the internet it takes forever or doesn't connect at all while son is on his xbox 360. Do I need to change up my router?
View 1 Replies
View Related
Apr 24, 2011
I use an ADSL router through my phone line to connect to the internet.My ISP supports downloading speeds of 2 Mbps. This is reflected on my router status page. But I have subscribed for a plan of 512 Kbps. I feel what My ISP has done is that it has reduced the speed of port 80 somehow to 512 kpbps i get download speeds of 2 Mbps..Is there any way to access websites or download data from websites from a port other than port 80 ?
View 2 Replies
View Related
Oct 20, 2011
I have my bigpond internet setup on my main pc,works fine connected to a router but i want to connect to the internet via ethernet cable on my 2nd pc. I have a ethernet port on the wall near it so that should work. I don't want to run a long ethenet cable from my router to my 2nd pc because there's a ethernet port right next to it.
View 6 Replies
View Related
May 17, 2011
I am facing a strange problem with my DIR 601 router. I am not able to access internet when I plug in the cable from my model to slot marked nternet' on the back of the model (which I guess is the right way). However, I can access the internet if I plug in the cable coming from modem into any of the 4 ports marked as 'LAN'.
View 2 Replies
View Related
May 15, 2011
I'm trying to change the way my network is set up by replacing an old cheap Switch with a newer Router that has some QoS options.
Modem: Motorola SBG900 LINK (provided by Time Warner, not purchased by me)
Old Switch: Zonet ZFS3008 LINK
New DLink Router: D-Link DGL-4100 LINK
Currently, my network is set up as follows, arrows being Ethernet cables:
Cable Modem w/ Wireless <-------> Old Switch <-------> 3 PCs and a Printer
With everything set up as shown above everything works fine, but I want to change it to:
Cable Modem w/ Wireless <-------> DLink Router via it's WAN port <-------> 3 PCs and a Printer
Simple change, right? Apparently not.A few things aren't working when I swap the DLink Router for the old Switch.
1. Internet does not work, though I can log into the DLink Router in a web browser and see all of the settings.
2. The IP address that used to go to the Modem (192.168.0.1) now goes to the DLink Router, and I cannot get to the Modem anymore via a web browser with any IP address.
3. The wireless from the Modem stops working.
4. I see the following when logged into the DLink Router and looking at the Status tab:
. . Connection Type :DHCP Client
. . Cable Status :Connected
. . Network Status : Establishing (Please Wait...) (it never establishes)
I have noticed that the DLink Router and Cable Modem both are doing DHCP, and I am wondering if that is creating a conflict that is causing the problem. However, simply disabling DHCP for the DLink Router and otherwise leaving the connections as they are still does not get the internet working.
<----------------insert a couple hours of fiddling with it some more------------->
The following setup works as far as letting everyone online, but QoS rules in Gamefuel are not getting enforced:
Cable Modem w/ Wireless (DHCP enabled) <-------> Old Switch <-------> DLink Router (DHCP disabled) via LAN port, leaving WAN port unused <-------> 3 PCs
I can now log into the Cable Modem via 192.168.0.1 and the DLink Router via 192.168.0.2. The wireless internet is also working again as well. My PC uses Windows 7, the other two PCs we have are on Windows XP and Vista.
View 10 Replies
View Related
May 26, 2012
I have a cisco 1801 (fixed), and want to use the fe0 WAN port to connect to the internet via a virgin media cable modem.
I am having a few issues (partly as I am new to cisco) and despite reading numerous posts both here and other sites, I am still stuck on how to setup the WAN side, I have read about virtual dial up & dialer interface.
View 1 Replies
View Related
Jul 7, 2011
I am trying to access home security camera from outslide my house.I have an AT&T internet coming into the house. They have a router that comes into the house and that splits off to another router in my house which carriers CAT5 all over the house. One of the wires go to another router that I use for my wireless devices.One of those wireless devices is an security camera.Here is my question. I want to view the camera from the internet outside the house. I have followed the instructions given by the manufacture for port forwarding. I have port forwarded the wireless router since the camera is connected to it. Is that wrong since the DSL is coming in one router and then going to another and then to the wireless
View 2 Replies
View Related
Feb 19, 2013
The ethernet ports across the entire campus including the halls all host multiple networks via one port. I connect to the port and I get one connection, and my friend connects to get a second connection through the same port, and a third person connected via the same port to get yet another connection. I think there may be 4 connections being hosted through this in total. Now, the university have 3 main streams of internet: 1 for Staff/postgrad, 1 for students, 1 for exchange students. The fourth connection type is intranet with only access to a portal. The purpose of the portal is to submit your mac address for wireless and ethernet to be assigned an IP address for both. The issue we are having is my friend needs to connect to the exchange students connection for actual internet access, but the ethernet cable will only connect her to the portal (all her details have been submitted). I have cycled through every window in the networking control panel and usually issues like this I can resolve within a couple of hours but how to identify other networks that are available through ethernet.
View 3 Replies
View Related
Feb 16, 2012
setup multiple wireless routers to one Internet connection. We have one cable modem (with built in wireless router) for Internet connection. Over a wide area (500 feet over two floors) I would like to connect to the Internet throughout this area wirelessly. The computers sharing the connection do not need to share with each other and do not need to see each other. Security is not a major factor. The building material is cinder brick walls (which weakens the wireless signal quickly).I have several older (2008 or 2009) wireless routers. I was thinking of putting these routers at various locations in the building with a wired connection back to the WAN modem. Each wireless router could the service a smaller area in the building.My plan is to turn off the DHCP on each wireless router. Do I need to run a wired cable (lan port to Lan port) back to the cable modem or can I use the wireless routers to connect to the wireless cable modem?
View 4 Replies
View Related
Jul 19, 2011
Our 6509 has seen better days and we know it's past time to replace it... Question is - go with similar or just use multiple 48 port switches? Then we have old Cisco 2800s in our 9 IDFs that would need updated as well.
We have a mixed environment with about 300 active clients along with about 15 servers and an EMC AX4 over 4GB fibre brocades for backup.
View 19 Replies
View Related
Dec 9, 2012
I have a Dell Laptop Latitude 610 and I have not been able to connect to the Internet via the ethernet cable port for some four months now. I've tried downloading software from Dell's web site, I bought (and returned) and USB to Ethernet cable, only to find out that it was a model ahead of what this machine needs.I've asked local repair place (Microcenter) what it might be, but they'll only tell me after I pay $70 just to open it up.Another repair guy said that it is probably the motherboard and it wasn't worth fixing. (Yet if it was, wouldn't the entire computer decide not to work at all?) [code]
View 3 Replies
View Related
May 11, 2012
I have Cisco L3 3560G switch which directly connected with router . i have configured Vlan 2,3 on the switch and assign port 2 & 3 respectably. I want to management both vlan 2 & 3 from from L3 port g0/10 .
View 6 Replies
View Related
Jul 3, 2012
I would like to associate multiple IPv4 networks with one physical interface in the router. All those multiple networks share the same broadcast domain(VLAN 5). I am aware that it's not possible to have multiple subinterfaces in the router with the same "encapsulation dot1Q 5". Am I correct that only option here is to configure all those networks as a secondary network to router physical interface? Or are there other possibilities than secondary addresses?
View 4 Replies
View Related
Aug 19, 2012
Redirecting a Domain to a IP:Port I host game servers for friends and strangers alike, but i'd like to make it easier for them all and give them dedicated IPs. Right now I include domain redirecting, but to connect to their server, they have to put in "example.com:xxxxx", x meaning their servers dedicated port. Is there any way that I can redirect a domain directly to "IP:Port"?
View 3 Replies
View Related
Jun 15, 2012
I don't know if I'm saying this right but, I have two computers in my LAN hooked up by a Ethernet cables to my modem/router zyxel pk5000z we were using theses computers to play together using Game Ranger. We were having some problems connecting to game rooms with a symmetric NAT. When the port forwarding did work it would only let me open ports for one ip adress for 1 computer it seemed. How do you open ports for all computers on your LAN?
View 1 Replies
View Related
Sep 27, 2012
I have a RV180W and a EnGenius EAP350 Access Point. The EnGenius supports multiple SSID's and VLAN tags them. If port 1 on the RV180W has VLAN 1 untagged and VLAN2 tagged, any connection to the EnGenius always gets an IP from the VLAN 1, even though they are connected to the SSID which is tagged with VLAN2.
View 3 Replies
View Related
Sep 10, 2011
We've run into some difficulty trying to take advantage of multiple WAN IPs in conjunction with the SRP547
What we're trying to acheive is the ability to port forward from our distinct public IPs to different internal servers. Looking at the options under Port Forwarding it looks like we can only configure forwards at the "WAN interface" level, but our problem is that we can't work out how to set up separate interfaces for each of our Public IPs...
Our ISP provides us with a fully managed NTU/router with a single "Internet" ethernet port, which we can use by statically configuring IPs on our end. For this configuration this port has been directly patched to the WAN ethernet port on the SRP547W.
We have been allocated a 255.255.255.248 (/29) subnet, giving us 5 usable IPs after the ISP's gateway address is taken into account, like so:
a.b.c.208 Network Address (/29 subnet)
a.b.c.209 ISP Gateway
a.b.c.210 IP1
[Code].....
I should mention at this point that we're running on firmware version 1.02.01 (023).
Is there a CLI or other method of configuration that might work if the web interface won't?
View 2 Replies
View Related
May 22, 2013
I am struggling to get our 887VA setup for our config.
We have a public IP range from our ISP and we have multiple servers behind our router. One of the servers need large ranges of ports open so I have ended up trying to use a ‘rotary’ nat pool which works fine but I cannot get the other servers to NAT correctly on their ports. It seems the rotary takes over.
Here is a snip of my config.
interface Ethernet0no ip addressshutdown!interface ATM0no ip addressno atm ilmi-keepalive!interface ATM0.1 point-to-pointpvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1!!interface FastEthernet0description Private LANno ip
[Code].....
View 1 Replies
View Related
Aug 15, 2011
I am at a loss on configuring a new ASA5505 for multiple static port translations.I would have expected to simply add several service command to a network object to complete the task, however, the service command overrides the previous and replaces rather than adds to the translations. [code] However, if entered in that order the 8443 overwrites the 8080 static translation.What is the correct procedure to establish multiple translations? If someone could also provide the "old" style for pre 8.2 release, I'd like to compare because I thought I used to do this with an access-list somewhere.
View 4 Replies
View Related
Sep 27, 2010
I have the following configurations in cisco CISCO7606 (R7000). Its meaningful to have the below configuration, wherein , we are allowing multiple vlans on the access port?
interface FastEthernet4/45
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 124-127,423,478,493,578,699,751,787,895,987,1981
switchport mode access
end
interface FastEthernet4/46switchportswitchport trunk allowed vlan 124-127,423,478,493,578,699,751,787,895,987,1981switchport mode accessend
View 3 Replies
View Related
May 21, 2013
We are migrating from a nother brand to an ASA Cluster running 8.4.5
We have a web-server on an inside interface listening on a non standard port - 20111. We have created a static NAT translating the public ip to the private, so If I do http://public-ip:20111 it works. (we are using a seperate public IP for this service only).
Now I need to create a NAT rule that will forward requests on BOTH port 80 and 443 to the same private ip and the same port number (20111)
The Private address is 10.99.250.20 and the "public" (I've replaced it in this example) is 172.16.16.16 I have managed to create a NAT that will translate 443 to 20111:
object network 10.99.250.20 nat (Private-DMZ,Outside) static 172.16.16.16 service tcp 20111 https
But if I try to add another rule like: nat (Private-DMZ,Outside) static 172.16.16.16 service tcp 20111 http It will simply replace the first one.
Is it possible to redirect both 80 and 443 from outside to the same port number and same IP on the inside?
View 1 Replies
View Related
Nov 7, 2011
I am learning the 2911 router. Is there a way to set a physical single RJ45 port to handle multiple WAN IPs? Or do I need to buy a port expansion module.
View 12 Replies
View Related
Dec 20, 2010
We have a 6509 that was connected to 2 other locations(location A and B) and our local lan (location MAIN). We wanted to move the location A and B to a 3750 switch and only allow the traffic that needed to access our location MAIN to come through the firewall. The only problem I ran into is that before location A and B were on different interfaces so in the 6509 firewall the routes for traffic to our MAIN location was done by static routes.
I.E.
static (MAIN_intf,A_intf) 192.1.1.72 10.94.10.72 netmask 255.255.255.255 0 0
static (MAIN_intf,B_intf) 192.2.2.72 10.94.10.72 netmask 255.255.255.255 0 0
[Code]....
because it has a static overlap, which makes sense to me, but my question is how do I configure the network to get this to work? Do I have to reconfigure my network and access-list? Do I need to add more ports between the 6509 and 3750? I'm not sure if this is the best way to do what we want. If something is not clear I'll try my best to explain the setup, but I just took over for our I.T. guy when he left.
I put 10.10.10.72 instead I should have put 10.94.10.72. the routed port is on a different subnet than the computer I'm trying to access.
View 4 Replies
View Related
May 21, 2012
We're going to be switching some of our gear from Foundry to Cisco, and were looking at the WS-C2960S-48TS-L. We currently have 3 different VLAN's, and I wanted to have 1 uplink back to our firewall (ASA 5550) and then let the firewall do the routing between the subnets. I realize that 1 link will carry the traffic twice then, but is that possibly with those switches to have all three vlans assigned to one port and then just let the firewall do the routing between the vlans or would I need to have 3 uplink ports back to the 5550?
View 1 Replies
View Related
