Cisco :: 1130 Laptops Dropping On And Off WLAN While Sat On Peoples Desks Not Roaming Anywhere
Jan 10, 2011
I'm fairly new to the whole Cisco WLC system so this may be a more simple question than I realise.We are having an issue with some laptops dropping on and off the WLAN while sat on peoples desks not roaming anywhere. I can see that some APs have Load profile failed. Looking in the docs is says that client density may have been exceeded. The AP in question has 12 clients attached however I read that the 1130's should be able to handle 24 clients. Is there a setting on the WLC that limits each AP to 12 users? Also is there a way to identify the AP by making its light flash for example via the WLC?
We have a customer who has a WAG120N as their broadband wireless router, and we've sold them some new equipment, part of which is another WAG120N as our salesperson didn't realise they had one.They have a section of the building which the current WAG120N will not reach. Reading around this forum, it seems that I can give the second WAG120N a different static IP on the LAN and use it to expand the range of the WLAN.If I've read correctly, I need to make all the wireless stuff exactly the same except to use different wireless channels on each router. But what do I do with the DHCP server on the second WAG? Is it fair to say that the clients won't suddenly jump to a different IP because they won't have a cause to request a new one? I read one comment that suggested the second should be configured for DHCP relay, and another which contradicted this. Presumably I just don't configure the ADSL on the second WAG as that will only connect to the LAN.
I am struggling with the following issue. I have 6 1130 Accesspoints in lightweight mode connected to a 2106 wlan controller which runs software version 7.0.98.0. Everything seems to work fine. Clients can connect to the wifi network. However, they don't get an ip address from the dhcp server which is on the same subnet as the wlan controller. See attached screenshots for configuration. I have also tried the internal dhcp server of the wlan controller, but the same problem remains.
The logs says: Dropping primary discovery request from AP e8:b7:4x:xx:xx:xx - maximum APs joined 6/6 There are 6 AP's connected
I convert IOS Cisco AP 1130 LAP to 1130 Autonomous mode. Well, the periphericals - clients connect to SSID AP no recieved I.P Adress, I think that is not possible active option DHCP server in AP 1130 dispositive. In mode I.P static clients the connection is established successfully.
I want to install wireless router in my home. It is 200 Square metres. Usb port does not meter for me. I want to connect 2 laptop 3 mobile phone via wlan. Which will be better E2500 or E3200 to cover whole area? P.S my internet speed is 40mbps
Our AP541N-E-K9 keeps dropping all WLAN connections and will not allow us to connect via WIFI. I have to switch the unit off and on but even so sometimes it will take 10 mins for the WLAN to accept new connections. Nothing has changed on the network for months as it is a very basic scenario ie Draytek DSL Router -> Cat5e cable -> AP541N-E-K9, thats it! The AP is really only used for guest access and may have about 15 staff connected via WIFI at any one time.
I would like to setup a 2504 to have one Guest WLAN and one Staff WLAN with a controller port for each WLAN connected to different devices.
I would prefer to connect the WLC Guest port to an ASA 5510 and the WLC Staff port to an internal 2960S switch. Will this work? I haven't setup a 2500 series controller previously.
I know what the problemis i need to tell the AP what the mac of the switchport is but i can not figure it out because it is a CATos Switch?on a IOS I would just use the Show interface command and use the bia but i dont know how to figure out the bia on a CATos?
I need to configure SNMP on our company Aironet 1130. I am told there is a tool we can use that will allow us do the configuration from a PC vs connecting directly to the device.. If that is true, where can I download it?
I have some 1130AG access point and I'd like to have :
- Multiple broadcasted SSIDs (because most of my clients are OSX and OSX doesn't deal with hidden SSID at all ! the clients have to enter the data each time which for WPA2 enterprise is really annoying) - Dynamic VLAN assignement (so my clients don't have to know to which VLAN they belong and so I can easily change them from one to another).
As it turns out, it's apparently not supported to have both. But I can't understand WHY ? What exactly is the relation between those features ? What's the underlying technical constraint ?
I can understand the cipher suite must match between all the dynamic vlan because of the way wlan works, but for this, I really don't see what the problem is ... (Especially since I only have one of the SSID that needs dynamic assignement, the other is really the 'guest' one).
I've got this weird problem with my AP. It keeps rebooting randomly. It happen to all the AP in my campus randomly. It happens recently. It have been commission for quite a long time. ie user able to connect and use it. its connect back to the controller to back in another campus. Below are the logs i gather.
*Jun 7 11:13:54.287: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up *Jun 7 11:13:54.290: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
Any info on successfully resetting an light weight 1130 AP to the factory settings? I tried the method described in the doc for 1130 on how to reset 1130 AP to the default settings, but it was not successful. I tried shutdown the AP, and plug in the power while press and holding the Mode button for about 3 seconds.This AP has lost it association with the WLC, is there anyway i can reset the AP to factory default and put in the correct IP address again?
Looking to set up a small office cheaply and quickly and was thinking about ordering a 2006 and some 1130s off EBay. Are the lightWeight 1130s compatible with the 2006?
IOS of my access point 1130 was deleted after bad manipulation. I have just a boot but not a flash on my AP. I can connect it just in console mode. What is the procedure to restore the IOS?
my college using WisM (WS-SVC-WISM-1-K9) as wireless controller , Cisco 1130 access point and Cisco Secure ACS 4.X Solution Engine 1113 Appliance as radius server. For username and password, we take it from existing Oracle database.
The problem is the password that store in oracle database is in encrypted format. Base from feedback from database administrator, the encrpytion is done by oracle - application layer and cannot be decrypt back.
To tackle this problem, we decide to use external script in php to verify the username & password...The php script will check directly from oracle database. If the username & password match, it will sent a boolean true (1) to the Wism controller and if the username & password not match, the script will send boolean false(0) to the Wism controller.
My question is, can WiSM module talk to php script? Can it receive boolean parameter from php script?
i have lwapp 1130 in internal network , i already configure dhcp with option 43, in my switch connected to ap i set vlan 1424 for management AP and the ap got ip addres from dhcp server. The wlc controller is in DMZ with ip 10.222.5.3, from switch connected to ap i can ping 10.222.5.3 , it aslo seperated by cisco asa firewall, i already set allow from 0.0.0.0 to 10.222.5.3 udp port 5246-5247 and 12222-12223.
I have a couple of AP's that are down and won't let me change to up. When I try to enable admin status I get a pop up window: " error in enabling admin status".
I have configured the WLC for power injectors with a 3550.
I have a lwapp 1130 here and it's no longer associated with the controller. I issued the clear lwapp private-config, it went through and cleared the config. Now when I try to issue the lwapp commands to set the ip and such i get ERROR!!! Command is disabled. I read that this means the static configuration is locked, but it did not say how to "unlock" it. how to get this re-enabled.
I have CISCO Aironet access point C1130 , but not able to connect by users, I can see below logs from access point.
Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000 Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247 Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000 Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247 [Code] .....
I just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
AP588d.09a7.93e4#conf t ^ % Invalid input detected at '^' marker.
Also,
AP588d.09a7.93e4#sh start startup-config is not present
Also, this is what I see in my flash:
AP588d.09a7.93e4#sh flash: Directory of flash:/ 3 -rwx 217 Mar 01 2002 00:07:10 +00:00 env_vars 4 drwx 128 Jan 01 1970 00:02:03 +00:00 c1130-rcvk9w8-mx.bin
I need to configure this device and set up for wi-fi access in my organisation network.
1) Virtual controller 7.3.112 is OK 2) N° 2 LAP 1130 e 1240 is Joined to controller OK 3) flexconnect in localswitch is OK 4) flexconnect in central switch IS NOT work.
I have a problem on a 1131ag Access point on recycle it stops and makes me maunually type BOOT at the ap: prompt
----------VVVVVVVVVVVVV---------------- ap: Xmodem file system is available. flashfs[0]: 282 files, 13 directories flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....
I have already performed the ap: set BOOT etc commands a dozen times with the same results. It says: The system is not configured to boot automatically.
I've been trying to get this one going for 4 months now..it was knocked out during a power outage while upgrading it.
I have a 1130 cisco access point,we are using this for wireless cisco IP phone connectivity to the network.Earlier access point was woring fine and we were able to make calls through IP phone.But we have relocated to new place.Now the access point is not working and we are not able to make the calls on the wireless IP phone as the access point is not working.But the access is in the netwrok and we are able to ping the IP address of the Access point.
We are contonuously getting the below loggs on Access point and the access point is getting power from the ethernet port of the switch not through the external powerr adaptor.
I want to be able to send snmp traps to my NMS alerting our NOC to when we reach our configured max-associations on an ap. We currently use both 1130 AG and 1140-2N in autonomous mode, no controller. I have found a debug command "debug dot11 station connection failure" and the output of a test AP shows us the fact that the maximum number was reached. I need to find if it is possible to trap on such information.
i' ve got 2 cisco 1130 AG AP's , i want both of them to broadcast 2 ssid's per AP, i've done so far but my clients cannot get a ip adress from the dhcp server.
We have a small ofice in the 3rd floor of a building and we are using 2 access points Aironet 1130 URL
Since some time now the space has become really crowded with access points. 1 AP is on channel 5 and is almost unusable. The 2nd one on channel 11 has some APs to fight with and with smaller signall strenght.
I have been researching and read a bit about changing some access point parameters (RTS/CTS/timers) on a multi access point environment. I want to do that while waiting for 5GHz AP's (and because not all clients support 5GHz).
I have 5 access points (WAP4410N) all connected to a befsr41 8 port/switch router, each AP has it's own SSID. Is it possible to to have one SSID for the entire wireless network so users do not have to change SSID's every time they change locations?
