Cisco :: 4900 Switches Support On LMS 3.1
Sep 12, 2011I need to know if Cisco Works LMS 3.1 can support 4900 switches series or not?
View 2 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 4900 Span Configuration On Switches
Sep 16, 2012i have configured SPAN on cisco 4900 series switches its a Loacal SPAN . as there is only commnads to complete this activity but hard luck its not working.
View 5 Replies View RelatedCisco Switches :: Do SG 300-28P Switches Support EtherChannel
Dec 28, 2010know if the Cisco SG 300-28P Small Business Switches support Etherchannel?
View 6 Replies View RelatedCisco Switches :: IEEE 802.1v Support On SMB Switches?
Nov 6, 2012Is IEEE 802.1v supported by some Cisco SMB switch ? Which model ?
View 3 Replies View RelatedCisco WAN :: 4900 - Outbound QOS Police Configuration
Jan 12, 2011I need to attach a QOS policy to a layer 2 WAN interface between two sites. This is actually an extended LAN circuit with 500Mb/s of allocated bandwidth. The interfaces are Gigabit so I want to make sure I don't attempt to transmit traffic faster than 500Mb/s. What is the best way to implement an outbound QOS policy that sets the minimum and maximum speed to be the same? This policy will be implemented on a 4900M with the 20 port GigE module
View 3 Replies View RelatedCisco Switching/Routing :: 4900 HSRP For LAN Fail-over
Jan 23, 2012Planning to implement HSRP in layer 3 switch.
We have two numbers of Cisco 4900 ME Switches. Basically want LAN failover from these devices. There are about 400 users in our network. I have attached rough network topology for your reference(I am not good at Microsoft Visio). Need to know implementation of the HSRP in these switches. Two distribution switches(Cisco 4900 ME Switches) are connected to 4 Access switches and these are connected to the LAN.
Cisco Switching/Routing :: Mac Filter Not Working On 4900 Switch
Aug 28, 2012 VLAN MAC address filter does not seem to be working on my 4900 switch. However the same config works fine when tested on my 3750 & 3560 switches.
Since user from different VLANs requires to be blocked, Unicast MAC address filter will not be feasible solution. VACL did not work on my 4506 switch too. K
Below is the config done on 4900 switch
mac access-list extended ABCpermit host 0003.0de9.d5ea anyexit
!
vlan access-map drop-mac 10
[Code]......
Cisco Switching/Routing :: ME 4900 Private VLAN Config
Feb 9, 2012We need to connect several DSLAMs on the 4900 switch, every DSLAM has 4 VLANs configured (VOIP service, MGMT, ADSL Private, ADSL Public), and sends the traffic for each service tagged with appropriate VLAN id according to the table:
VOIP: 608
MGMT: 594
ADSL PRIVATE: 2900
ADSL PUBLIC: 2930
On the DSLAM side it is very simple configuration, just a normal trunk with 4 VLANs transversing the link. On the 4900 I need to isolate the traffic for ADSL PRIVATE & PUBLIC service so DSLAMs connected to the same switch do not have L2 connectivity between them. For VOIP and MGMT they must communicate with each other. DSLAM acts also as a VOIP GW so it must communicate with other DSLAMs for VOIP service. Also VLAN 200 is configured on ME 4900 for switch management traffic.
This 4900 Switch connects to MPLS PE router, which offers L3 VPN service for VOIP & MGMT service, and L2 VPN for ADSL service (PPPoE traffic to BRAS). Fortunately we have ES+ linecard to support many ethernet features. I tried this config:
1) VOIP, DSLAM-MGMT, MPLS-MGMT configured as normal VLANs
2) ADSL PUBLIC & PRIVATE configured as isolated secondary VLANs, primary VLAN for ADSL PRIVATE is 2008, for PUBLIC 2308
3) Configure DSLAM facing ports on ME 4900 as private-vlan trunks
4) Configure ME 4900 uplink port to MPLS PE as a private-vlan promiscous trunk
5) Configure ethernet services on MPLS PE for each tag that comes from ME 4900 (ES+ cards are awesome, i love them:D )
6) Apply L3 VPN service for VOIP and DSLAM-MGMT, and L2 VPN for ADSL service.
But at least this last command should list on spanning tree forwarding state also the ADSL VLANs or not?
Here is the output of the show interface switchport.
Cisco Switches :: Does SG300-10 Support RIP
Jun 20, 2012In the CLI documentation for the SG 300 Series, it shows sh ip route rip as a command. I have installed the latest firmware and that command is no longer available. Does the SG300 series support RIP?
View 6 Replies View RelatedCisco Switching/Routing :: 4900 - How To Verify Link Before VLAN Extension
Mar 23, 2012we got a dark fiber betwwen two sites away from each other 30 Km,i need to connect this sites acts as backup dc to main dc in main site using cisco 4900 Switches in BK-DC anf 6513 in the main site,how can i verfiy if this fiber oparates as L2 and i can extend vlan servers,is it via "sh cdp neigh" and "sh vlan br"?
View 2 Replies View RelatedCisco Switching/Routing :: 4900 Failed To Read Transceiver Serial
Jul 30, 2012When I insert the TwinGig Converter in a Catalyst 4900M you get the following error message: Failed to read transceiver serial eeprom on port Te2/1, try reinserting.This error is probably because the device expects 10Gig transceivers to be connected to the device not 1Gig.I used the TwinGig 4 module and 8 SFP ports are connected. But when i type in the the "hw-module module <slot> port-group <group> select gigabitethernet" the command is not available. [code]
View 1 Replies View RelatedCisco Infrastructure :: 4503 - Connection To 3COM 4900 At Physical Layer
Oct 2, 2003I have at the core a CISCO 4503 and need to connect various 3COM 3300/4400/4900 access switches thru fiber. The problem is that the Cisco core 4503 switch fails to recognize only the 4900 3com switches ie the link status shows down. The fiber multitude link is tested and OK.The modules on both the switches ie 1000baseSX are also tested and ok.
The Cisco switch has a 6port gb ic with 1000baseSX moules and the 3COM 4900 has a 4-port 1000baseSX module.
Cisco Switching/Routing :: Setup TwinGig Converter To Use GLC-SX GBIC In 4900?
Jun 17, 2012I am having problems configuring a 4900. I have entered the following commands:
hw-module module 2 port-group 1 select gigabitethernet
hw-module module 2 port-group 2 select gigabitethernet
hw-module module 2 port-group 3 select gigabitethernet
hw-module module 2 port-group 4 select gigabitethernet
However no matter what I try, it never sees the GLC-SX gbics I have in the TwinGig converter.
PERSW001#sh interfaces status mod 2
Port Name Status Vlan Duplex Speed Type
Te2/1 inactive 1 full 10G No X2
Te2/2 inactive 1 full 10G No X2
Te2/3 inactive 1 full 10G No X2
[code]....
Cisco Switches :: Can SF300-24P Support POE On All Ports
Jun 18, 2012An end user is looking to connect 21x IP Cameras to the switch and they require at least 6W port port. Now, the datasheet states that each port on the SF300 provides 15.4W.I need to double check so that the end user will not start connecting the IP Cameras and then half of them might not fire up.
View 1 Replies View RelatedCisco Switches :: Getting Better Ssh Shell Support On The SF300?
Sep 9, 2012Any chance of getting better ssh shell support on the SF300?Being able to do things like this are very useful:
ssh 10.1.1.1 "sh version"
ssh 10.1.1.1 "sh run"
Cisco Switches :: How Many SFP SRW2048-EU Switch Support
Aug 22, 2011SRW 2048-EU(webview) switch will support how many SFP minigibic whether 2 or 4 ?
View 1 Replies View RelatedCisco Switches :: Does The SF300 Support Stacking
Jul 20, 2012Does the SF300 support stacking? If it does, which port(s) are the ideal ones?
View 1 Replies View RelatedCisco Switches :: 200 Series SNMP Support
May 28, 2013Am I correct in thinking that 200 series swiches now support SNMP using v1.3?
View 1 Replies View RelatedCisco Switches :: VLAN Support On ESW 500 Switch?
Jul 4, 2009How many VLANs does the ESW 500 switch support?
View 4 Replies View RelatedCisco Switching/Routing :: 4900 Capturing VLAN Traffic And Set Destination To GE Ports
Jan 24, 2012At present we are having a 4900 series switch where we are running one monitor session.Additionaly we are in need of capturing VLAN traffic and set the destination to 2 * GE ports , both are in the same switch.Due to the limitation of two monitor sessions per switch , we thought of putting the destination ports as port channel but it looks like it is not supported.
View 1 Replies View RelatedCisco Switches :: SOHO97 / 800 - Unable To Support IPv6
Dec 7, 2010I've got older SOHO97 which I want to use as a backup for Cisco 800 but I can not find any information if it actually supports IPv6. Neither the data sheet [URL] nor the Cisco Feature Navigator [URL] suggest it has any IPv6 support at all.
View 1 Replies View RelatedCisco Switches :: SF302-08P Support For IP 7942 Phones
Oct 22, 2012i am looking at quoting the SF302-08P for a client which will have three small offices interconnected via single mode fiber. I am planning on connecting them to a 3560 switch. Each office will have no more than 3 - 7942 phones. I reviewed the notes on this switch and it seems it should support this phone type without any issues.
View 8 Replies View RelatedCisco Switches :: Does SG200 Support VLAN Trunking
Apr 15, 2013does SG200 support VLAN Trunking?
View 1 Replies View RelatedCisco WAN :: 3500 - How To Check Switches Support IPV6 In LAN
Feb 6, 2013i want ti migrade lan from ipv4 to ipv6.. how can i check my switch support ipv6?
i am having cisco 3500 and d-link managed and unmanaged switchs.
Cisco Switches :: SF300 Does Not Support Complete DHCP?
Apr 5, 2013I have some issue from last 2 month on sf300.
The problem is that sf300 does not support complete dhcp, for that i put different internet modem.
I connected one internet modem in vlan 1 so users from that vlan can access internet and default gateway is nothing but Internet modem ip. user in the vlan are not communicate with other vlan because, other vlan users default gateway is Interface ip address. How i can give access to vlan 1 to access other vlan .
See the attached.
I have to used static route in all 3 devices or any one.
Cisco Switches :: SG200 Support For RADUIS Device Authentication
Dec 6, 2011I am unable to successfully authenticate my SG200 to either a Cisco ACS or Windows2008 RADUIS server. (C3750x on the same network authenticates fine).
Q1. Is this feature (management login authentication to a RADIUS server) supported on the SG200?
Q2. Is so is there any configuration guidance available for both the SG200 and CSACS / WindowsServer2008 NPS?
I hav not got as far as 802.1x uthentication yet, but config example of this would laso be useful.
Cisco Switches :: Does SG500X Support Redundant Power Supply
Jun 1, 2013Does SG500X support the following
redundant Power Supply?PIM sparse mode (PIM-SM), PIM dense mode (PIM-DM), and PIM sparse-dense mode?Layer 4 prioritization: enables prioritization based on TCP/UDP port numbersUni-Directional Link Detection (UDLD) — monitors a link between two switches and blocks the ports on both ends of the link if the link goes down at any point between the two devices
Cisco Switches :: Does Sge 2010 Support Routing Information Protocol (RIP)
Dec 27, 2011if the sge2010 switch support Routing Information Protocol (RIP) and if so how do I enable it. I have a small wireless router that support it and would like client connected on it te bo visible from the wan side and that worked when I had another device doing the routing with RIP support the wireless router was picking up that information and the routing for the wireless client was working.
View 2 Replies View RelatedCisco Switches :: SG300-28P Can Support 24 Ports With 154w Per Port
Mar 6, 2013I want to know if the SG300-28P can support 24 ports with 15,4w per port at the same time.
View 3 Replies View RelatedCisco Switching/Routing :: Do The Catalyst 2960-S Switches Support Pre-standard PoE?
Jun 14, 2012I have a customer with Cisco 7940 and 7960 IP phones that they do not plan to replace. They do want a new LAN and are looking at the Catalyst WS-C2960S-48FPD-L and WS-C2960S-24PD-L as access layer devices.
these switches support the Cisco pre-standard PoE required by the 7940 and 7960 IP phones.
Cisco Switching/Routing :: 3560-C Series L3 Switches Support OSPF?
Jul 16, 2012OSPF normally only comes with IPservices image and not IP Base image. The 3560-C series data sheet says that it only suport IP Base image, yet it mentions that support for OSPF in included. Are there any restictions in the OSPF support?.
View 7 Replies View RelatedCisco Switches :: Does ESW 520 24P Support Mirroring 20 Ports Traffic To 1 Destination Port
Sep 5, 2011Does the ESW 520 24P Support Mirroring 20 Ports Traffic to 1 Destination Port?
View 3 Replies View RelatedCisco Switches :: QoS Setup On SGE2010 To Support VoIP Trunks Between PBXs
Aug 28, 2012how to configure QoS on my SGE2010 to support my Toshiba CIX PBX VoIP trunks. The infrastructure is straight forward: PBX(1)<==>SGE2010(1)<==>SGE2010(2)<==>SGE2010(3)<==>PBX(2) where PBX(1) and PBX(2) are connected through three SGE2010's that are trunked via fiber between buildings. I don't have VoIP handsets and the PBX's are on their own VLAN. Everything else has been a breeze in these switches but I have no experience with QoS
View 6 Replies View Related