I added Cisco AIR-1142 AP which is registered with WLC 5508 in to LMS 4.1. After restarting AP, the status in LMS showing as unreachable. I am not able to save the configuration in AP and also not able to add SNMP parameters . what is the issue or what are the normal procedure to add a LWAPP in LMS.
View 4 RepliesI any running Cisco Works LMS 4.0 on Windows 2008 Enterperise Edition with SP2.I am facing 2 issue which are below:
1. Get message "You are using unsupported Version". As per Cisco document Windows 2008 Ent edition is support by LMS 4.0
2. All of my devices are showing unreachable. I already double check the Devices Credential include SNMP (Read and Write community) and Username and passwords.I can accessble all devices via telnet from the same Cisco Works Machine.
I have discovered my switches in LMS but it is showing unreachable what can be the reason ?
View 5 Replies View RelatedI have encountering a problem with a new installation at my clients side recently.We have a 5508 wlc and a bunch of Laps connected to it.Recently we associated a 1142ap to the same controller.The issue we are facing is that , the client laptops that are connected to THIS ap are showing maximum of only 54mbps in their network information dialogue box.Initially i couldn't understand why this could happen.But after a bit of research , i came to know that this could happen because of ``unticked`` data rates in the controller , or because of not using wpa2 with aes as the security standard for N-series access points.Now i have enabled all data rates in the High Throughput section as well as enabled the correct encryption standard.But still the issue persists.We have checked with multiple laptops , to rule out the possibility of a faulty n/w card
View 3 Replies View Relatedmy computer is a dell dimension 1100, with a Linksys WMP54G wifi card, running vista home basic.In the wifi thing in the notification area, it shows two wireless networks, One is my normal SSID (Lower Net), and one is "Unidentified network". They are both on one wireless connection (Wireless Network Connection 3). When i try to go on the internet, it says i'm not connected. i tried disconnecting from the unidentified network, but that disconnects me from lower net too.
View 13 Replies View RelatedAfter reconfiguring my LMS 4.1 from snmp v2 to snmp v3 the endhost aren't reachable anymore. Before configuring the snmp v3 I have purged the endhost database in order to repopulate it. After the jobs run no endhost could be added to repository. It just says unreachable.
Could it really be a snmpv3 issue? Everytihng else is working as before. I'll have to go back to snmp v2.
is this possible, i need to convert a 1242AG Autonomous back and forth this weekend to use for a quick project for testing. i need to do: take the AP into LWAPP mode (i know how to do this with the aironet utility) take the ap from LWAPP back into a AP mode so i can use it as my access point again. [code]
View 3 Replies View RelatedSomeone has mentioned only 25 nodes are supported by the 1524SB and that one AP gets bogged down by 20 nodes or more.
View 0 Replies View RelatedI am trying to upgrade an autonomous IOS 1242 AP to LWAPP and I am having an issue with finding the right code to complete the upgrade. I have upgraded the AP to c1240-rcvk9w8-tar.124-21a.ja2.tar, but now I think I need a JX version of code to have it join a controller, and I can't find this anywhere on the Cisco site.
View 5 Replies View RelatedCan the AIR-WLC526-K9 be used for any other access points besides the AIR-LAP521G-A-K9 access points? Does the 526 controller use the LWAPP protocol?
View 3 Replies View RelatedSo we have a cisco asa 5505. Once a day now (random times) it will suddenly be unreachable along with the hosts connected. If I console in and ping a host from the asa, suddenly it becomes reachable from the outside world again. My job prohibits me from posting the configuration online.
View 10 Replies View RelatedI have a couple of 1040N autonomous APs want to convert to light weight APs.
View 8 Replies View RelatedWhat is the difference between WIRELESS LAN LWAPP and WIRELESS LAN LWAP RECOVERY images? I believe the RECOVERY is used in the upgade process - but what is the other used for?
View 1 Replies View RelatedI want to upgrade the ios ap-1240AG me to leave it in standalone mode.What default ip should take my ap?How should we be the tftp command to update the IOS on my ap?I am using tftp server of windows xp?
View 1 Replies View RelatedWe have a few AIR-LAP1041N-E-K9 and 2106 controller. One of the 1041N began rebooting in a loop. All over AP work fine. This morning, AP normally loaded at once. Two hours later, after AP reboot, situation repeated itself. Output from console:
using eeprom values
WRDTR,CLKTR: 0x85000800 0xc0000000
RQDC ,RFDC : 0x80000037 0x0000018c
[Code].....
I would like to downgrade Cisco Aironet 1142N to autonomous. But I would like to know is there any way to download the LWAPP IOS before upload the Autonomous IOS ? because I want to upgrade the 1142N from autonomous to LWAPP when I buy a LAN Controller.
Is that possible to use that backedup LWAPP IOS when I want to upgrade the Cisco Aironet 1142N autonomous to LWAPP?
I have cisco LWAPP 1242 AP already joined controller but 802.11b/g shows down on the radio 0 interface. I tried to enable it but it comes with an error" Error in enabling admin status". I have resetted the AP to factory default settings and even replaced with NEW AP.
View 3 Replies View RelatedI am running big wireless network, with 20no of 5500 with 7.0.116.0 version. I have more than 20,000 AP's. All LWAPP which are up for more than 200-300 days has to be rebooted, this problem is with all AP's. clients are not getting connected,after reboot they work fine.how do the same from ncs.
View 5 Replies View RelatedI need to upgrade several 1252s from autonomous to LWAPP. I have not been able to find the upgrade tool for 1250s or instructions for CLI upgrade. I wil be using NCS to do final configuration once the APs come online.
View 1 Replies View RelatedI would like to know AIR-AP1252AG-A-K9 (Autonomous AP) can be changed to LWAPP AP by changing IOS image??
View 1 Replies View RelatedI try to change the AP mode of my LWAPP 1242 from local to bridge mode. But when the AP reboots it never associates with the controller, i have to reset it manually.I have the same issue with a LWAPP 1142.I tried to modify the AP mode configuration through the controller CLI but it's the same behaviour, AP never associates.Is there any particular parameter or configuration to perform before changing AP mode?
View 3 Replies View RelatedI need your expertise regarding how to convert from autonomous to LWAPP using AIR-SAP2602i-s-k9 with IOS version of ap3g2-k9w7-xx.152.-2.JA.
I'm following these commands but it is not available
debug capwap console cli or debug lwapp console cli
I cannot proceed to convert it Did I miss something or the 2600 series doesn't support LWAPP convertion ?
i have lwapp 1130 in internal network , i already configure dhcp with option 43, in my switch connected to ap i set vlan 1424 for management AP and the ap got ip addres from dhcp server. The wlc controller is in DMZ with ip 10.222.5.3, from switch connected to ap i can ping 10.222.5.3 , it aslo seperated by cisco asa firewall, i already set allow from 0.0.0.0 to 10.222.5.3 udp port 5246-5247 and 12222-12223.
View 4 Replies View Relatedin my test LAB i have used a 5505 running 9.1.1.I have setup a DC (2008R2) and then AD Agent.I have configured and used Identity firewall rules which worked like a charm.I have also used LDAP Auth which also worked fine.I then disabled all the rules but kept the identity firewall checked.Since it was a lab environment, i had to remove the DC for other tests.A few hours later the ASA initially was stuck.I used the console and i saw it could ping noone! not even directly attached PCs or defgw (i was able to ping them before it stucked).No arp table also!the asa did no NATing so no xlate entries were vavailable.Then i sshed to it.I got a blank screen and from console i could see cpu-usage from ssh to 20%I opened a second ssh: nothing. Blank Screen again. cpu-usage from ssh to 40% (overall ~50%)I opened a third ssh: nothing. Blank Screen again. cpu-usage from ssh to 65% (overall ~75%)I issued reload from console! Nothing! it was trying to shut down!I issued reload quick-> that is when console was lost!!I have to unplug it.
The DC that was removed was also the DNS for the ASA.The only log message i could see, before it stuck was "AD Agent is out of reach".i have ttried this 4 times. Always the same. 100% reproducible.I disabled the identity firewall-> no problem! it worked for days.100% reproducable.I downgraded to 8.4.5--> the same for both above actions.
I'm having an issue where when I upgrade from 8.2(5) to 8.4(2) on an active/passive asa 5585 running in transparent mode I can no longer reach the standby ip. The BVI interface appears to be created properly, the device IP and standby IP are listed in the config under the BVI interface and my inside and outside interfaces are both joined to BVI1-group.
View 1 Replies View RelatedI have a strange behavior and a simple proble . I configured the following static route
ip route 10.84.22.0 255.255.254.0 10.84.23.254
That I advertsied in eBGP :
router bgp 65000
network 10.84.22.0 mask 255.255.254.0
the IP next hop 10.84.23.254 is cascaded on my customer LAN . At nominal time the router advertsed the route in BGP
pjnb1376#sh ip bgp nei 57.213.169.169 ad
Next Hop Metric LocPrf Weight Path
*> 10.84.22.0/23 10.84.23.254 0 32768 i
When the lan interface of the router goes down , the router still advertise the route !!! Even if the IP next hop
10.84.23.254 is not reacheable anymore ....
The box is a Cisco 1941 using
1900-universalk9-mz.SPA.151-4.M1
The problem is that that the routers are not reachable form the corporate LAN after some time. Pinging the routers IP is not working anymore. When the network cable is unplugged and plugged in again the routers are responding again. The same applies when I connect my Laptop to the router. The interface is responsive right after I connect the cable. Also other devices on the network can ping the router. But after a few hours or sometimes 1,5 day the router is unreachable form the corporate network.
The problem first started a few weeks ago. The configuration did not change. The router 878 was not responsing and after changing all the cables and conncting it to another swith the problem remained. So I suspected a hardware failure and bought a replacement 888. After configuring the 888 it showed the same behaviour as the 878 router. The DSL connection is working all the time. I can even set up a vpn connection to the router and start a telnet session. than I can ping the internap IP of the router but pinging another device is not working.
What I noticed after the command sh int vlan1 is that the last input counter keeps increasing.whats causing this or how to debug?
I have one instance of WCS 7.0.172.0 (on a Linux host) and a fleet of WiSMs that I'm upgrading from 7.0.98.0 to 7.0.116.0. Every time I run thru the upgrade process from within WCS (scheduled to run overnight, off peak hours) all of the controllers that were upgraded then show as "unreachable". Grepping thru wcs-0-0.log shows messages that the controllers are unreachable via SNMP but running an "snmpget" from the command line to any of the affected controllers works just fine. The only way I've found to remedy this is to stop and restart the WCS service. Considering how long that takes with my deployment...I'd rather not do that every time .
View 2 Replies View RelatedIs it really the case that the ASA will not generate ICMP Host Unreachable messages for sub nets connected to any of its interfaces (in breach of RFC1812) as claimed here: [URL]
I'm investigating a situation where an organization uses ASAs to control traffic between different v lans in their internal production systems as well as Internet traffic. They are having problems with internal load balancing because the ASAs do not (as currently configured) generate Host Unreachable packets. Can this be changed in the configuration or not? I have to say, if it can't then I'd urge them to find something else to route between their internal sub nets.
I have a Cisco controller WLAN solution where I want to bridge traffic locally on a remote site, when using Cisco 1140 LWAPP.Is the only way H-REAP ?
View 3 Replies View Relatedupgraded my home AP from Autonomous to Lwapp. I was an Idiot and thought i was getting an IOS upgrade. I need to revert it back to autonomous and a simple "mode" button reset doesnt work. I read that I need to Reload original IOS software, but It appears I cant get it without a support contract. I cant afford servicenet and need to obtain old ios to revert to factory default 12.4(10b)JA1. Do I need a contract to roll back? Is there an archive (backup image) of the old IOS that could be still stored on the device. I didnt back it up and need to obtain the image.
View 5 Replies View RelatedI'm using a wlan controller with 1242ag converted to lwapp, i'm trying to enable 5.8 but when i change the from local to bridge the lwapp disappear from controller. May be that the firmware does not support mesh !I'm following the 4402 wlan manual at page 641.
View 5 Replies View Relatedsome days ago I succesfully converted AIR-LAP1041N (lwapp) to AIR-AP1041N (autonomus).I used c1140-k9w7-tar.124-25d.JA1.tar which is available to download in Download Software Section for this AP.But there are any autonomus to lightweigt firmware for this AP.I tried to use c1140-rcvk9w8-tar. 124- 21a.JA2.tar for 1140 but AP hungs after that. How can i back to LWAPP version in 1041?
View 7 Replies View Related