Cisco Firewall :: 7940G - Is ASA 5505 Almost Dead
Feb 16, 2012
I just got a refurbished ASA 5505.It works fine until un need to reload it or unplug it from power en replug it, when I do this and it's warm (even after some minutes of uses, so still physicaly cold while touching it), in this case, it simply reboot in chain withing 1 or 2 seconds. I have to unplug it from power and wait 5 minutes before replugging it to power.
I don't know if it's a problem from the power supply (that makes some noise, but I think it's normal), I tried loading more the power supply by plugin in some PoE device (Cisco 7940G) and it works fine, so it looks more like it's a problem on the ASA itself.
Must I send it back to the vendor? I tried updating the ASA image, but this don't changes anything.
View 2 Replies
ADVERTISEMENT
Mar 20, 2013
I currenty have 2 cisco 5510 firewalls one of the firewals is completly dead but contains a Cisco ASA SSM-10 can i remove this card and just place it into a working unit, will i have any problems doing so.
View 1 Replies
View Related
Jun 13, 2011
I have 2 (and maybe soon 5 more) 7940G phones to add to my network, which already has a Netgear POE capable switch. I've since discovered that early Cisco POE isn't the same thing as current POE, and the switch doesn't power the phones.
I was looking at adding a Cisco SD208P 8-port switch to power the phones, but I soon discovered it only has 4 POE ports, and I'm not sure that this switch will even power the 7940G phones. And if the other 5 phones show up, I'll need two of those switches with no room for expansion on the voice network.
Will this switch power those phones?Is there another small switch available so I don't have to replace my existing switch infrastructure to get these phones to work? Or do I need to scrap the phones and get something newer that will work with the current POE standards?
View 2 Replies
View Related
Sep 13, 2011
I have remote site in which site to site vpn is configured with hub site using 5510 model. now i am using load balancer in which 2 isp will terminate one is isfy and other is reliance . now i want if suppose ipsec-tunnel is configured primary with sify. if sify link fail at hub site then at remote site should be able to communicate with reliance that is secondary?
View 7 Replies
View Related
Sep 7, 2011
How I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
View 1 Replies
View Related
Oct 22, 2011
I have a simple question regarding dead peer detection on the ASA 5520. I am using a cellular VPN device to connect back to an ASA 5520 and I have noticed that the connection drops at random periods during the day. The vendor for the cellular device recommends disabling dead peer detection on their device, which I have done. The question is, where is this disabled on the ASA? is it the IKE Keepalive setting under the tunnel group option?
View 1 Replies
View Related
Jun 22, 2012
I tried to upgrade the cisco boorloader pf WLC 4402 from version 4 to 7.2. I updated ER.Aes FOR 7.2 (EARLY RELEASE.aes). It was updated perfectly and then I rebooted controller....now i can only see blank screen from connected console.I tried the flash of other lan controller but its not working because the issue is in the ROM as the boadloader file is in the ROM which is corrupted now i want the solution to upgrade the boatloader file inside the ROM.
View 1 Replies
View Related
Jul 13, 2012
I have an old RV082 that I suppose has failed. The red diag light on the front panel is lit and nothing works. I've already replaced the unit, so I don't really need to fix it. Here's my issue: the setup on the old unit was pretty complex with a number of port forwards and other non-default settings. I'd like to recreate those items on my new router, but they were never written down so I don't know what they were. I've tried to connect a computer to one of the LAN ports, but they're all dead. Is there any way to get at the configuration page?
View 2 Replies
View Related
Apr 24, 2012
We were having a discussion of ios firewall vs. asa for smaller clients(less than 50). On using ios firewall(zbf or cbac)and an asa 5505/5510. One of the arguments brought up on using ios firewall on the router is that a router will do an ip sla failover. I have configured a number of isr's for this and i know it works good.
View 1 Replies
View Related
Feb 19, 2012
I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies
View Related
Aug 23, 2011
setting up an ASA 5505 to be used as a firewall between a BT internet router(BTNet service) and a Cisco 3560 Lan switch. BT have presented me with a cisco 3800 series router with the following details:
Network Address Network Mask BTnet NTE Router LAN Address
There are 2 Gigethernet ports on the back of the router port Ge0/0 is connected to the BT NTE and the status light is flashing green. Int ge0/1 is connected into port int e0/1 of the ASA but i am unable to get any connection.
View 21 Replies
View Related
Feb 27, 2013
I'd like to see some REAL LIFE comparisons of ASA firewall throughput (a bit like this one for ISR G2 Routers - [URL].
The reason I ask is that I recently upgraded a firewall from an ASA5505 to an ASA5520 on a small network where the only outside connectivity was a single 10meg Internet circuit with an IPSEC VPN (not landed on the firewall but on a router) to another site.
When I swapped out the firewall the users noticed a big improvement. The firewall is not doing anything out of the ordinary - no IPS or VPN, just standard state full inspection.
View 5 Replies
View Related
Dec 22, 2011
Trying to set up a asa 5505 in transparent firewall mode. I cannot set the management ip address:
ciscoasa> enable
Password:
ciscoasa# config term
[Code].....
View 7 Replies
View Related
May 3, 2011
I have been working with ASA 5510,20,40,80 but not with 5505 this vlan and its interfaces are quite confusing.Just want to know how it works and its connectivity to Cisco Switch.Do i have to put the interface of the switch in the same vlan as i am creating the interface vlan in firewall ?Now the switch port connecting to this Eth1 interface should also be in the same vlan ? i.e vlan3 ?? or it will be in trunk ? The default configuration shows the eth0 with no access vlan and interface eth1 with access vlan 2... does it mean the eth0 is in vlan1 ? (Nativ Vlan ) ???
View 4 Replies
View Related
May 28, 2012
I have a cisco asa 5505 firewall. Is it possible to block secure websites in it like [URL]? I have already tried regular expression filtering but it filters only http traffic.
View 4 Replies
View Related
Feb 26, 2011
I am trying to configure our ASA 5505 so that our users can access our ftp site using [URL] while inside the firewall. Our ftp site is setup so that you can reach it by either browsing to the above url or by browsing to ftp://99.23.119.78 but we are unable to access our ftp site from either route while inside the firewall. We can access our ftp site using the internal ip address of 192.168.1.3.
Here is our current confguration:
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0 !interface Vlan2nameif ATTsecurity-level 0pppoe client vpdn group ATTip address pppoe setroute !interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveobject-group service DM_INLINE_TCP_1 tcpport-object eq ftpport-object eq ftp-dataport-object eq wwwaccess-list ATT_access_in extended permit tcp any host 99.23.119.78 object-group DM_INLINE_TCP_1 access-list ATT_access_in extended permit tcp any interface ATT eq ftp access-list ATT_access_in extended permit tcp any interface ATT eq ftp-data access-list ATT_access_in extended permit tcp any interface ATT eq www access-list 100 extended permit tcp any interface ATT eq ftp
[code]....
View 6 Replies
View Related
Nov 21, 2012
New to the ASA 5505 8.4 software version, but here is what I'm trying to do:
-Single static public IP: 16.2.3.4
-Need to PAT several ports to three separate servers behind firewall
-One server houses email, pptp server, ftp server and web services: 10.1.20.91
-One server houses drac management (port 445): 10.1.20.92
-One server is the IP phone server using a range of ports: 10.1.20.156
Basically, need to PAT the ports associated with each server to the respective servers behind the ASA 5505. Is anything missing from this config? Do I need to include a global policy for PPTP and SMTP? [code]
View 11 Replies
View Related
Apr 27, 2011
I'm integrating a Cisco ASA5505 with a Websense proxy. I have a configuration setup where we have four routers which are used for Internet access. There are two VLAN's - Guest and Private. What I would like to achieve is making the use of available bandwidth by load distribution via GLBP, and filtering users web traffic. Two routers will be used for a GLBP group in one VLAN, and the other two routers will be used for GLBP in another VLAN.The users are connected to a Cisco 2960 switch and are in their respective VLAN's. I'm planning a 802.1q trunk to a Cisco ASA from the 2960 switch, carrying both VLAN's.What I would like to know is if there is a CSC module (or similar) which has Websense installed on it, and if it is possible to setup the ASA5505 in transparent mode to filter the traffic in this way? Hopefully this would allow multiple users to take advantage of the additional bandwidth, and not be restricted by using a traditional proxy setup which where all web traffic would be originating from a single MAC address.
View 1 Replies
View Related
Jul 5, 2012
Is it possible my Laptop Ethernet port is dead?After I got home today I noticed that the store that passed by caused a short power outage. I knew this because several electronic devices that rely on constant power were reset.Next to be noticed was that my computer had no connection to the internet, and my Ethernet port has a constant orange light on.I proceeded to perform a full network restart for my modem, router, and computer. This solved the internet connection to my router. My roommate was able to connect via an Ethernet cable to the internet on any of the routers ports, but I was still unable.However,I was able to connect to the wireless on my computer. Unfortunately no matter what port, or cable I use my Ethernet port still is unresponsive to it all, and still has the constant orange light.you.Specs:Manufacturer: Gateway
Model: P-78
OS: Windows 7
CPU/Ram: Intel(R) Core(TM) 2 Duo P7350 2 GHz / 4090 MB
Video Card: NVIDIA GeForce 9800M GTS
Sound Card: NVIDIA High Definition Audio Conexant High Definition SmartAudio 221
View 9 Replies
View Related
Dec 10, 2012
So I rebooted my router after adding a MAC address to the MAC address filtering scheme, and now it wont get its static IP and broadcast. what have I done and how can I fix it? and before someone says "Turn it off and on again" and "hard reset it", ive done this! it was first port of call!
View 3 Replies
View Related
Apr 29, 2011
Just for no reason that I know of the wireless stopped working. I can can connect to the SSID fine and there seems to be good signal strength, but no wireless internet access.
I have up to date February 15, 2011 firmware, 205NA, hardware version = B1.I have done a reset with no luck.I have done a 30/30/30 factory reset = no luck
View 8 Replies
View Related
Jul 3, 2012
After replacing my WRVS4400N Gen2 with a RV220W, I would like to know if there is a solution to resurrect the dead wlan, killed by the well known buggy firmware some time ago (I could not let it fix it in those days, cause some of use may need those devices every day, so "send it in and we fix it in some weeks" was a bad joke).
I do not need the "old" router atm, but it would be nice to have a backup device in hands, because the VPNs created by those devices are vital for my business. Is there a cheap way to fix this device, or would you say it would be cheaper to buy something else? (And after those two devices, I'm not sure that the next one would be a Cisco device again .
View 1 Replies
View Related
Jul 25, 2012
In a lab environment, I have a stack of two 3750v2-48ts switches. I upgraded the stack from 15.0(1)SE2 to 15.0(1)SE3 using archive download-sw.
Switch 1 in the stack reloaded and came back with the new image.
Switch 2 appears to be dead. No console out put. When power is applied, the SYST LED blinks 22 times, then stops. I've held in the mode button for up to 60 seconds, held in mode while applying power, removed the stack cables and repeated...there's not a whole lot else I can think of to do at this point.
View 1 Replies
View Related
Apr 30, 2012
I have an issue with my firewall,each time i configured a trunk port in the firewall and connect a sw 2960S with a trunk port also, all the interfaces in the Firewall go down ( virutal intertaces, inside, outside , dmz) , also another switch 3750 that is connected to another port in the firewall( access port only) it start to a new negotiation of spanning tree.What could be causing this problem? the firewall didnt sedn bdpdu i think the IOS of the firewall its a 8.2
View 3 Replies
View Related
Jun 12, 2012
we are planning on connecting a new aquired company to ours soon?We will connect the remote site to the HQ via a D3. I've been told we will need to have a firewall between them and us for a time. I was thinking of terminating the D3 connection at the remote site of 80 users. Can I use the asr as a firewall as well, to protect the HQ from the Remote site - or should I use a seperate appliance?I was thinking of a asa5505 but, am concerned with bandwidth limitations of the box?
View 1 Replies
View Related
Sep 11, 2007
I want to configure an ASA 5505 in transparent mode (7.x). Somehow, I got it to work.. but i need some kind of step by step description. I just want to connect it with outside on a route .. inside in my LAN. Its working now with one ASA. But in the Web Interface the Interfaces inside and outside are down.. but its working.
View 5 Replies
View Related
Feb 23, 2013
My laptop's keyboard just dead and I can't no longer activate it wifi.My laptop is Toshiba and it usually use fn+f8 key to activate, but since my keyboard got broken yesterday,I don't really know how to activate it.
View 2 Replies
View Related
Oct 11, 2012
My Vaio's screen is dead due to a dead graphic card (long/short/short beeps when starting up). But i can't easily remove the harddisks and connect them through an external USB-SATA because they are in raid 0 configuration..The laptop still works (i hear the windows 7-soundlogo) but I can't get access to it since i cannot see what i am doing for installing eg VNC or Remote Desktop software. Command line commands? try portable VNC installations? remove harddisks and bring them to a recovery centre?
View 1 Replies
View Related
Mar 4, 2011
Model: Linksys CM100 Cable Modem, purchased December 2010
Modem goes dead immediately after 3rd light goes solid. All lights go out and the modem stops functioning completely. Using the reset button gives no response, the modem stays dead. Upon unplugging and plugging it back in, the modem turns back on and cycles through the lights, only to die out once again.I was initially able to get it to stay alive by starting it with the Ethernet cable disconnected then plugging it in once the modem had connected, which I found odd. After a relatively short period, say 20 minutes, the modem would randomly die out again. However even that has since stopped working.
View 1 Replies
View Related
Jun 13, 2012
Have to re-boot 1-2x daily. Updated firmware through Cisco, followed by about 7-8 support calls. They all recommend some sales thing, new router, computer update and clean-up, or blame it on my modem (not the case). When E1500 goes down, all wired and wireless connections are lost. They all recommend some sales thing, new router, computer update and clean-up, or blame it on my modem (not the case).
View 4 Replies
View Related
Feb 15, 2012
I had an old Cisco Catalyst 2948G switch that I have not used in about 7 years down in my basement. I powered it on and went through the process of clearing out the configurations, and I got to a point where one of the commands to clear out the config asked me to install jumpers for "ROM" and "ERASE". There is a third jumper labeled "NO BOOT". They are numbered J6, J7, & J8 respectivelyI found the jumpers inside and put the jumpers on them and ran the command expecting it to remove any old configurations I had on the switch and bring it back to factory state, but I was wrong.
View 3 Replies
View Related
Dec 10, 2012
I had an old Cisco Catalyst 2948G switch that I have not used in about 7 years down in my basement. I powered it on and went through the process of clearing out the configurations, and I got to a point where one of the commands to clear out the config asked me to install jumpers for "ROM" and "ERASE". There is a third jumper labeled "NO BOOT". They are numbered J6, J7, & J8 respectivelyI found the jumpers inside and put the jumpers on them and ran the command expecting it to remove any old configurations I had on the switch and bring it back to factory state, but I was wrong. This switch runs CatOS, not IOS.When power is applied to the switch, the fans turn on as normal, but no LEDs are lit on the front. There are green LEDs lit next to the jumpers inside, but that is all. I am not able to get any response from it on the console at all anymore.The LEDs that are lit green inside are labeled "CR5" and CR6".
View 2 Replies
View Related
Feb 24, 2013
I have a Cisco 4500. Recently some of the ports seem to have "died"/ will not supply Poe to phones. Some work for data only. Other do not work at all. The switch has been restarted, this made no difference.
View 2 Replies
View Related
