So I rebooted my router after adding a MAC address to the MAC address filtering scheme, and now it wont get its static IP and broadcast. what have I done and how can I fix it? and before someone says "Turn it off and on again" and "hard reset it", ive done this! it was first port of call!
View 3 RepliesNearly every morning/evening I have to re-boot my router to get internet access. Netgear N300 ADSL2+ modem router Model DGN 2200 (had about a year), Windows 7 64bit Home premium Laptop connected wirelessly, Windows 7 64Bit Home Premium desktop connected by LAN cable. ISP BT Internet. Until recently this set up has been working OK with occasional loss of interent access and need to re-boot router. The internet light has been showing red on those occasions. Over the last two weeks I have found that when I turn one of computers on although all lights on router are green I have no internet access. I have to re-boot, then all is OK until the next day when I have to re-boot again. My phone line appears OK with no noise on line, no reported problems on BT broadband staus. The thing that puzzles me is that the lights are all green on the router yet my networking icon on the pc shows an exclammation mark and 'no internet access' and I do not have access to net.The wireless connection is OK with excellent strength.
View 7 Replies View Relatedwhen the wireless router is plugged in to my acer desktop computer (running on windows 7) it will cause the desktop to reboot itself numerous times what do i need to do to make this stop so i can hook up wireless to the laptops i have?
View 1 Replies View RelatedJust for no reason that I know of the wireless stopped working. I can can connect to the SSID fine and there seems to be good signal strength, but no wireless internet access.
I have up to date February 15, 2011 firmware, 205NA, hardware version = B1.I have done a reset with no luck.I have done a 30/30/30 factory reset = no luck
Have to re-boot 1-2x daily. Updated firmware through Cisco, followed by about 7-8 support calls. They all recommend some sales thing, new router, computer update and clean-up, or blame it on my modem (not the case). When E1500 goes down, all wired and wireless connections are lost. They all recommend some sales thing, new router, computer update and clean-up, or blame it on my modem (not the case).
View 4 Replies View RelatedI upgraded my E2500 with the last version of firmware but now is dead. the power led is turn on, but the ping are discontinued. the other problem is that after 10/15 sec, the router will restart automatically. i try with tftp but after the reset of router does not change anything.
View 5 Replies View RelatedMy router appears dead. I assume that I need to reset it and replace the firmware.
View 3 Replies View RelatedHow do I troubleshoot to find out if my wireless router is dead? I have a WRT160N. It's been giving me problems lately, so I thought I'd update the firmware. Long story short, I had to reset it, but I still can't get into it. I have gotten into it, but when I try to save it gets hung and then I reload and then it starts all over again.It does work hard- wired--I can access the internet with ethernet. But I can't get the dang thing reset and then upgrade the firmware...
Somehow I set this router up to act essentially as a repeater, an extension of the wireless network that is "anchored" (not the right word I'm sure) by the wireless router provided to me by my DSL provider. I want to do the same thing once I get this one working again--set it up as an extension of the existing network so I can essentially walk around the house with my iPad and not have to re-log in when passing into a new "zone".
MY ISP is AT&T. I have their Westell DSL modem, with a bridged connection to a Linksys wireless router. The router is connected via ethernet to a dead computer: a 7 year-old Dell desktop that will boot up but shut down right away. I have been able to connect multiple laptops wirelessly to this network. I thought an ethernet connection was required in a home network such as mine? The cable has been plugged into a dead computer for several months and frankly I'd like to get rid of the desktop. What exactly is the ethernet requirement - just to be plugged into a port? Could I theoretically just yank the ethernet card out of the desktop and use it instead of the whole dead system?
View 5 Replies View RelatedI've got an IPTV network with Bell FibeTV with Motorola VIP1216 (the DVR master) and VIP1200 (slave) cable boxes. All the coax cables in my walls form a wired ethernet network instead of a cable TV network. To get better wireless coverage in my home, I've set up routers as wireless access points at each of the cable boxes. Essentially I've plugged the router into the ethernet bridge of the cable boxes, and disabled DHCP and gave it a static IP and did all things I needed to do to disable all the routing capabilities and make it into a switch (here's what I did, step by step: [url...]). So when I go from one room to another, I just select a new wireless access point to get maximum signal strength and speed.
View 6 Replies View RelatedIt has happen suddenly : Internet is not working through WRT150N, though it work when directly connected to the modem. So I think it is a router issue :On the WRT150N, Internet light is flashing fast for 2 seconds, then is off for 2 seconds, then flashes, then is off and so on, wether there is a device (computer, modem, ...) plugged or not, through the blue ethernet connector.And sometimes, Internet light stays off from power on, whatever is done with ethernet connexions (yellow or blue).
When connected to the blue ethernet Internet connector, my pc ethernet lights don't blink (nor the link light or the data light)I have try the 30-30-30 reset cycle. But it doesn't improve.I have tried the loopback test : connect an ethernet cable from the one of yellow ethernet port of WRT150N to the blue ethernet of WRT150 N.Sometimes, the light for the yellow ethernet port goes on for a few seconds, while the Internet light continues to flash. After a few seconds, both go off.Sometimes, as soon as the loopback is made, the 2 lights go off, and if a computer is plugged to the yellow port, the ethernet lights of the computer and the router stays off.But I can access to WRT150N through Wifi and I can access to the web management.
I've bought my E4200v2 via eBay, because original Cisco store doesn't ship to my country (Israel).My first unit was... defective, I think I wrote about the issue on this forum a while ago.It had connection troubles, always in a dead loop, saying "Connecting..." one to 100 times it managed to connect, and suffered slow internet connection speed, where all speedtests gave me 60% of my actual internet speed.Which is 30mbit.I'm sure about my ISP, it uses next.gen technology, they have their own underwater optic cables. Without Cisco router, only dialer, I get 100% of my internet speed, or with another router as well.I decided to RMA my e4200v2.
Out of context question: Why there's no option to specify server name instead of server IP? our ISP uses domain name for connection, rather than IP address, as they have a lot and a load balancer above 'em.Now, to the original issue.Refund is no option, RMA again is no option, too much time and money.Maybe there is a solution? It just can't be the reality, that two out of two units are not working. I heard this router is very good. And I heard the v1 is working very well in Israel. so It can't be our country that is the problem.By the way, I've called my ISP and they've switched me to MPLS connection for a try, so in a router you just switch to "Automatic configuration - DHCP" and it pulls IP, DNS servers and connected to the internet, but was hooooribly slow.
So I'm back to dialer. the main still is the "Connecting..." loop, sometimes says "Connected" for a second, and then connecting again... It manages to pull DNS addresses though, but never the IP and never managed to stay connected.All the connection configs are very basic, you know it. Server IP, username, password, keep-alive, MTU (I've tried auto, and a ton of other combinations recommented by our ISP or Cisco).My latest idea was to film how I burn it or throw a rock at it and send to Cisco the video, but that's kinda too much, it's too early for such decisions, especially when already $300 were spent.
i brought a new wrt120n from the retailer and when i tried to connect the modem and configure, my phone gets dead and i couldnt connect it to the internet.
View 1 Replies View RelatedWRT400N worked great for 18 months.
Last week the Verizon-supplied DSL modem went bad (wasn't receiving data) and was replaced.
Now I can get Internet direct out of modem, and when I connect it to router the router's Internet light is on, but it seems to stop there. Devices connected to router via Ethernet or wifi don't get Internet.
I'm able to get to the router's admin console via Ethernet and wifi, but no Internet.
I have just ugraded to a E3000 from a wrg54 to increase the rang, but am still having dead spots. How to increase the range.
View 1 Replies View Relatedi have a peak wireless router connected to my desk top or should i say modem, which was security enable with password and used to use my laptop a toshiba which used to automatically connect to my wirelless router i then rebooted router as couldnt remember password as my son wanted to connect with his laptop an xbox from his bedroom . since rebooting the router my son has conection with the xbox and his laptop but my laptop want find my nework
View 1 Replies View RelatedI had to reset my Linksys WRT300N router because of issues with my internet provider and now I cannot get my Dell Inspiron E1405 to connect wirelessly. I am getting a status of limited or no connectivity with an ip address starting with 169. I have included the following:
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 2, 32 bit
Processor: Intel(R) Core(TM)2 CPU T7200 @ 2.00GHz, x86 Family 6 Model 15 Stepping 6
[Code]....
My Internet speed slows down from about 4mpbs to 1mpbs approx until I reboot after which it runs fine until it slows down again.I have a Netgear DGN2000 router, and have tried restoring to factory settings and using it that way - made no difference.
View 1 Replies View RelatedModel No.BiPAC 5200S, Firmware: v2.10.1.0(UEO.C2C)3.6.0.0The router was supplied by Tata Indicam nearly 7 years back. Now I tried to configure for Bsnl BroadbandConfiguration is completed as specified in the user manual without any hitchRestarted the system as directed. But rebooting is not fructified. The system did not respond. Hence closed. Later verified the diagnostics and found that the adsl synchronization is failed. I am not a qualified person to analyze the problem.
View 1 Replies View Relatedis there a way how to reboot DIR 615 using some kind of script?From time to time I need to reboot the router
I also have Dlink DNS 323 and somebody discovered a way how to shutdown it down using Wget:
[code]...
Is it possible my Laptop Ethernet port is dead?After I got home today I noticed that the store that passed by caused a short power outage. I knew this because several electronic devices that rely on constant power were reset.Next to be noticed was that my computer had no connection to the internet, and my Ethernet port has a constant orange light on.I proceeded to perform a full network restart for my modem, router, and computer. This solved the internet connection to my router. My roommate was able to connect via an Ethernet cable to the internet on any of the routers ports, but I was still unable.However,I was able to connect to the wireless on my computer. Unfortunately no matter what port, or cable I use my Ethernet port still is unresponsive to it all, and still has the constant orange light.you.Specs:Manufacturer: Gateway
Model: P-78
OS: Windows 7
CPU/Ram: Intel(R) Core(TM) 2 Duo P7350 2 GHz / 4090 MB
Video Card: NVIDIA GeForce 9800M GTS
Sound Card: NVIDIA High Definition Audio Conexant High Definition SmartAudio 221
Can I schedule a weekly reboot with this router?
View 3 Replies View RelatedI have to reboort my router every day to get back an internet connection? I have a desktop and a laptop plus iPads, etc. The laptop loses connectivity every day about the same time. My only solution so far is to reboot the router. I realize that the client lease time is set to 1 day by default but isn't it supposed to ask the modem for another day of life when this happens?
View 5 Replies View RelatedI unplugged my router and when I plugged it back in, it stopped working. The 4 port lights and the ethernet light come on immediately when I plug it in instead of the normal boot sequence.
I tried resetting it, leaving it unplugged for long periods, using the power supply from my other router,... nothing works.
I have a Linksys WR-110 wireless router that has been acting up lately. I have 10mbps cable internet and have my desktop computer hardwired to the router. I notice that after a few days the download speed gets down to the 2mbps range. Verified by { URL}. If you do a hard boot (unplug for 30 seconds) it will go back to 10mbps speed again. But it seems after a few days it slows own again.
I always run speed test to verify, and it always runs back up at advertised speeds once i hard boot.
Why would this be happening?
seeing very strange behaviour of router router is connected to switch to provide analog when swich configured as trunk the router crash and reboot but when change to access its stable
[code]....
My laptop's keyboard just dead and I can't no longer activate it wifi.My laptop is Toshiba and it usually use fn+f8 key to activate, but since my keyboard got broken yesterday,I don't really know how to activate it.
View 2 Replies View RelatedMy Vaio's screen is dead due to a dead graphic card (long/short/short beeps when starting up). But i can't easily remove the harddisks and connect them through an external USB-SATA because they are in raid 0 configuration..The laptop still works (i hear the windows 7-soundlogo) but I can't get access to it since i cannot see what i am doing for installing eg VNC or Remote Desktop software. Command line commands? try portable VNC installations? remove harddisks and bring them to a recovery centre?
View 1 Replies View RelatedModel: Linksys CM100 Cable Modem, purchased December 2010
Modem goes dead immediately after 3rd light goes solid. All lights go out and the modem stops functioning completely. Using the reset button gives no response, the modem stays dead. Upon unplugging and plugging it back in, the modem turns back on and cycles through the lights, only to die out once again.I was initially able to get it to stay alive by starting it with the Ethernet cable disconnected then plugging it in once the modem had connected, which I found odd. After a relatively short period, say 20 minutes, the modem would randomly die out again. However even that has since stopped working.
I have a simple question regarding dead peer detection on the ASA 5520. I am using a cellular VPN device to connect back to an ASA 5520 and I have noticed that the connection drops at random periods during the day. The vendor for the cellular device recommends disabling dead peer detection on their device, which I have done. The question is, where is this disabled on the ASA? is it the IKE Keepalive setting under the tunnel group option?
View 1 Replies View RelatedI tried to upgrade the cisco boorloader pf WLC 4402 from version 4 to 7.2. I updated ER.Aes FOR 7.2 (EARLY RELEASE.aes). It was updated perfectly and then I rebooted controller....now i can only see blank screen from connected console.I tried the flash of other lan controller but its not working because the issue is in the ROM as the boadloader file is in the ROM which is corrupted now i want the solution to upgrade the boatloader file inside the ROM.
View 1 Replies View RelatedI have an old RV082 that I suppose has failed. The red diag light on the front panel is lit and nothing works. I've already replaced the unit, so I don't really need to fix it. Here's my issue: the setup on the old unit was pretty complex with a number of port forwards and other non-default settings. I'd like to recreate those items on my new router, but they were never written down so I don't know what they were. I've tried to connect a computer to one of the LAN ports, but they're all dead. Is there any way to get at the configuration page?
View 2 Replies View RelatedI just got a refurbished ASA 5505.It works fine until un need to reload it or unplug it from power en replug it, when I do this and it's warm (even after some minutes of uses, so still physicaly cold while touching it), in this case, it simply reboot in chain withing 1 or 2 seconds. I have to unplug it from power and wait 5 minutes before replugging it to power.
I don't know if it's a problem from the power supply (that makes some noise, but I think it's normal), I tried loading more the power supply by plugin in some PoE device (Cisco 7940G) and it works fine, so it looks more like it's a problem on the ASA itself.
Must I send it back to the vendor? I tried updating the ASA image, but this don't changes anything.