is there a way how to reboot DIR 615 using some kind of script?From time to time I need to reboot the router
I also have Dlink DNS 323 and somebody discovered a way how to shutdown it down using Wget:
[code]...
Can I schedule a weekly reboot with this router?
View 3 Replies View RelatedI recently installed a tp-link router everthing works ok. The problem is when I turn off my pc and disconnect it and all attached devices (modem, router ect) from the electric supply. When I turn it back on I have no internet connection until I reboot the pc a second time.This problem only occurs when I disconnect the router from the electric supply. If I just shut down without disconnecting then I can turn it on and it connects to the internet without any problem.
View 5 Replies View RelatedI just installed two FPS games.. My router reboot every time those game search for servers list. ( So i can't actually play those games) I have a dir-601 n-150 dlink router. I have successfully played online with another connection. I tried opening some ports, but it didn't work. The firmware is up to date.
View 5 Replies View RelatedA few weeks ago I noticed that at 9:00am sharp every morning my internet access dropped, and would come back up four minutes later.
The router is connected to a DSL-526B in bridge mode. My first thought was that the modem was playing up, so I factory reset it and reconfigured it.
I checked my ACLS and didn't see any rules that started or ended at 9:00 am so I just lived with it for a week or so until it got so annoying I contacted my ISP to see if they were resetting anything at 9am.
By accident, I saw that my wireless radio was being enabled aat 9:00am, as it had been for the last 2 years, when I first bought the router. But this problem has only started a few weeks ago.
So I changed the wireless schedule to see if that was really the cause for the reset, and sure enough, whatever time I changed the wireless schedule to, the router rebooted at that time.
I've also factory reset the router; twice; the first time I saved/restored my configuration, the second time I recreated all configuration from scratch.
why enabling the wireless radio resets the router, and why disabling it doesn't, and how to correct this behaviour?
Region : Sweden
Model : TL-MR3420
Hardware Version : V1
Firmware Version : 3.12.21 Build 120523 Rel.37880n
ISP : Ownit
I am having problems with my TL-MR3420 router, it disconnects WIFI all the time. This occur several times a day and is very annoying.
I have quite recently upgraded to the latest firmware but the problem seem not to have been resolved. It also seem that it is mostly the WIFI service that is the problem. The usage of wired routing is working even when the WIFI is disabled.
I have 2 computers connected to the router (via cable). The problem is that have to reboot the router several times per day because one or both computers lose their internet connection. This happens regardless if one or two computers are turned on.
Router: DIR-615
Firmware version 4.00
Hardware version: D1
Computer1: Win7 64
Computer2: Win Vista 64
Region : India
Model : TL-MR3020
Hardware Version : V1
Firmware Version : 3.14.2 Build 120817 Rel.55520n
ISP : HNS/Instanet (Cable Internet)
I am using the Router in 3G/4G mode, with WAN only (PPPOE) enabled. I have set a personal SSID in the Wireless > Wireless Settings > Wireless Network Name field.
I do not see the particular SSID on my computer, instead on every reboot / restart of the device a random SSID is generated. see attached screenshot. I can connect and everything works well, but I have to enter the WPA key after each reboot.
Region : Netherlands
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.4 Build 110429 Rel.36959n
ISP :
I have a flaky internet connection, and it drops every few days. I've thus far powercycled my router by unplugging and plugging it back in, which fixes the issue.
I'm traveling soon, and would like to be able to have access to my stuff remotely, even after the connection drops.
I have two ideas:Run a script in Windows 7 which would soft reboot the modem - free, not sure if soft reboot is enough though. If that doesn't work, Get a hardware which would powercycle the router - haven't researched if these are readily available and cheap
Is there a way to schedule a soft reboot of my router using Windows system tools? I'd schedule it to reboot every night.
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
ISP : Comcast
TP-LINK WDR4300 750N Dual-Band router issue.
I started having a problem with a VONAGE V-Portal VoIP adapter losing connection to the Vonage server. I Unplugging the adapter and waiting doesn't solve the problem. The only way I can temporarily fix the issue is to reboot my TP-Link router. Once the router is rebooted the adapter can connect to Vonage. After a few hours it loses connection again. I have set the adapter to use a static IP outside of the DHCP reserved pool. This didn't fix the issue.
I have had vonage for many years and this router for the last 10 months and not had a problem until the past two weeks. Nothing only my local network changed. All of my PC's have no problems with internet access during the time that the Vonage adapter gets an Error 004 (lost connectivity). I still have connectivity with my ipod touch and other internet enabled devices as well. I was using 8.8.8.8 as my DNS server in the router DHCP configuration as well as the static value when I tried using a static IP with the V-Portal. I then switched all system to the ISP (Comcast) preferred DNS servers. The problem still exists. The only way to get the Vonage adapter back to running is to reboot the router.
I should mention I have Motorola Cable modem to a TP-LINK WDR4300 750N Dual-Band router. I have two Vonage vportal adapters plugged into the a couple of the LAN ports on the TP-LINK router. One vportal is my roommates, one is mine. Everything has been working fine for the last 6 months and now one or the other Vportal loses communication through the router, but the other vportal doesn't lose connectivity. It only happens to one of them and it varies as to which one will ERROR out.
Region : Germany
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP :
all my systems are configured under "IP & MAC Binding". Binding is activated globally and all check marks for every ID are set. After i finished my configurations, the "ARP List" status shows, that everything is bound - so far everything is great. The problem appears after a router reboot or after shutting the router down and powering it on again. The "ARP List" then shows only a few of my IDs and their status is unbound. I need to go back to the "Binding Settings" and hit "Save" - after that all my IDs appear in the ARP-List and everything is OK again.
Region : UnitedStates
Model : TL-WDR4900
Hardware Version : Not Clear
Firmware Version : 3.13.29 B 130126 R 50426n
ISP : Comcast
1. Any device which is switched off (WiFi turned off) wont be able to connect again without a router reboot. I get a connection timeout error when trying to connect. Happens only when there are more than 3 devices connected. (all my devices are ARP linked to MAC addresses with fixed IP addresses - I thought this would eleminate the problem but not)
2. Streaming videos stop playing after 5 minutes. I have to click on the play button to start the stream again. When I test the internet speed through speedtest.net or speedtest.comcast.net, I get over 40MBPS consistently.
3. The router doesnt recogonize 3TB or above HDDs on either ports
4. As long as all devices connect to one channel (either 5G or 2.4G), the connectivity speed is excellent. The moment a device connects to the other channel, the connection speed fluctuates a lot on both.
I have a DIR-601 and I'm trying to play the IOQuake3 game Urban Terror (UT). Every time I try to get a list of servers the DIR-601 stops and reboots.What is that? Flood protection? Something else?
View 4 Replies View Relatedi have a DIR-615 Rev C1, firmware 3.13.
After a reboot my password doesn't work anymore (wich is normal I guess) and all default passwords dont either. Such as ''Password'' or ''Admin''.
I have multiple computers on my network as well as cell phones logging in as wifi. At least once a day I have trouble or another computer has trouble getting on line through my network. I have to unplug my router and replug. Its as if it doesn't recognize the ip address until reboot.
View 1 Replies View RelatedI just recently setup a network in my home and selected the D-Link DIR-655 router to manage traffic. It's not clear to me when this issue first appeared as I've been away so apologies for not having a proper timeline.The router is setup in it's default configuration with only the IP Address being changed due to a conflict with my DSL modem. I don't have any experience with routers and it seemed to be working fine so I didn't mess with it.However, the router goes into what appears to be an endless series of reboots making it completely unusable. This can occur anywhere from immediately upon a cold start power to a few hours into it.I suspected a defective router and since I had been traveling the warranty was of no use so I purchased a brand new router last week which is also a DIR-655. The new router is doing exactly the same thing as the original one.
If I disable the wireless functionality both routers perform flawlessly for extended periods (many days/weeks). As soon as I enable wireless what appears to be warm start reboots begin as mentioned anywhere from immediately to a few hours along.Since I am new to networking in general and routers in particular I thought perhaps am I doing something wrong and hence my post here.The f/w in the new router is 204NA. I don't recall the f/w release of the initial router but I did update it within the last month to whatever was the most current from D-Link. If it's important to know the f/w release of the initial router I will find it for you.
Two (2) DIR 655 routers appear to enter a state of perpetual warm start reboots whenever wireless functionality is enabled. This begins anywhere from immediately to a few hours after a router cold start.Disabling the wireless functionality completely stabilizes both routers.
Any way to schedule a reboot of a DCS2102?I've got 3 of them here, and they are very good but every now and then they seem to stop writing to the storage. They haven't frozen cause I can still connect to them via a browser
View 2 Replies View RelatedI had to reset and reboot. I entered the router ISP and went through the 4 step process then rebooted.
My question/problem is now the router is wide open. How do I find page where I can enable the security settings and lock down the router to the outside world?
Have 13 DCS-920 Every few days a few random cameras will will hang/become unresponsive at random intervals. The cameras require that I unplug the cameras before they will respond. When the cameras are unresponsive I cannot access the camera via a web browser, the D-View Cam software, or the setup wizard. This is a problem as they are all mounted in positions requiring a ladder to access.
I have some connected via 802.11g and other hard wired over 10/100 cat-6 Ethernet cable.
I have a problem with switches SPS208G2. They're conected with SFP module after Linksys SPS224G4 and another swithes. After reboot switches which are conected with SPS208G2 don't see link. However previous switches phisical link status is up show LED, but protocol status is down show command "show interface status". I changed Firmware, it doesn't work, i changed SFP module it doesn't work. Yesterday i got new Firmware ls_sps2xx_bx-10600.ros but no luck. I don't understand what's wrong with switches SPS208G2. I have 500 or 700 switches SPS208G2. They installed different places at city. They don't ping until reboot their or previous switches. Reboot previous switches usually doesn't work, works only physical reboot or pulling SFP module.
View 1 Replies View RelatedHave several DCS-5300 cameras (firmware 1.06) and randomly the cameras will reboot.
D-Link says to set to factory default, but that is not physically possible.
Region : Germany
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 120820
ISP : German university ISP
I have a big problem with several TP-Link routers (WDR3600, WR1043ND, WR741ND), always with the latest firmware and also with older ones. After a day or so, my internet & network connection will drop all of a sudden and all the routers need a reboot. There is no indication on what provoces these lock-ups. The routers can handle heavy traffic (bittorrent /w 100s of connections) but will stop working when browsing casually. The web-GUI will become unreachable. No pings to the outside are possible anymore, not even to direct IPs (8.8.8.8 for example). No pings to devices in the same network are possible either.
After reboot WLC , the switch port was err-disable , the cause is link flap after we reboot 3 times , the switch port link flap err-disable every time? We don't know why the WLC rebboot will cause it , it just normal action on device the WLC version is 7.4.100.0 link switch with access port , no port channel , no portfast.
View 11 Replies View Relatedi have a peak wireless router connected to my desk top or should i say modem, which was security enable with password and used to use my laptop a toshiba which used to automatically connect to my wirelless router i then rebooted router as couldnt remember password as my son wanted to connect with his laptop an xbox from his bedroom . since rebooting the router my son has conection with the xbox and his laptop but my laptop want find my nework
View 1 Replies View RelatedI had to reset my Linksys WRT300N router because of issues with my internet provider and now I cannot get my Dell Inspiron E1405 to connect wirelessly. I am getting a status of limited or no connectivity with an ip address starting with 169. I have included the following:
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 2, 32 bit
Processor: Intel(R) Core(TM)2 CPU T7200 @ 2.00GHz, x86 Family 6 Model 15 Stepping 6
[Code]....
My Internet speed slows down from about 4mpbs to 1mpbs approx until I reboot after which it runs fine until it slows down again.I have a Netgear DGN2000 router, and have tried restoring to factory settings and using it that way - made no difference.
View 1 Replies View RelatedModel No.BiPAC 5200S, Firmware: v2.10.1.0(UEO.C2C)3.6.0.0The router was supplied by Tata Indicam nearly 7 years back. Now I tried to configure for Bsnl BroadbandConfiguration is completed as specified in the user manual without any hitchRestarted the system as directed. But rebooting is not fructified. The system did not respond. Hence closed. Later verified the diagnostics and found that the adsl synchronization is failed. I am not a qualified person to analyze the problem.
View 1 Replies View RelatedSo I rebooted my router after adding a MAC address to the MAC address filtering scheme, and now it wont get its static IP and broadcast. what have I done and how can I fix it? and before someone says "Turn it off and on again" and "hard reset it", ive done this! it was first port of call!
View 3 Replies View RelatedI have to reboort my router every day to get back an internet connection? I have a desktop and a laptop plus iPads, etc. The laptop loses connectivity every day about the same time. My only solution so far is to reboot the router. I realize that the client lease time is set to 1 day by default but isn't it supposed to ask the modem for another day of life when this happens?
View 5 Replies View RelatedI unplugged my router and when I plugged it back in, it stopped working. The 4 port lights and the ethernet light come on immediately when I plug it in instead of the normal boot sequence.
I tried resetting it, leaving it unplugged for long periods, using the power supply from my other router,... nothing works.
I have a Linksys WR-110 wireless router that has been acting up lately. I have 10mbps cable internet and have my desktop computer hardwired to the router. I notice that after a few days the download speed gets down to the 2mbps range. Verified by { URL}. If you do a hard boot (unplug for 30 seconds) it will go back to 10mbps speed again. But it seems after a few days it slows own again.
I always run speed test to verify, and it always runs back up at advertised speeds once i hard boot.
Why would this be happening?
seeing very strange behaviour of router router is connected to switch to provide analog when swich configured as trunk the router crash and reboot but when change to access its stable
[code]....
my E1000 will slow down and, as I've done with other routers, I'll typically unplug it for about 20 seconds and reboot it. However, with my E1000, about 9 out of 10 times, after I plug it back in, the four port lights on the the left will dimly flash but I get no activity on the three right blue lights (the wifi, internet and power buttons) and thus no wifi or internet.
For example, this morning I unplugged the router and modem, plugged the modem back in and waited for the modem activity lights to start flashing and then plugged in the router. The four blue port lights on left side flashed very dimly but no other activity. I unplugged it and re-plugged it in about 10 times and finally, the lights on the right side popped on and all was well.