Cisco Firewall :: ASA 5505 Without IPS Can't Remove Some IPS Configurations
Dec 5, 2012
I have an ASA 5505 without any IPS module.While copy/pasting some configurations from another 5510 with IPS I copied my mistake the some of the IPS configurations part. Now I can't remove it.When ASA starts I get this Warning:
...WARNING> IPS policy is configured without an SSM card.
*** Output from config line 828, " ips inline fail open"
Those lines are:
policy-map Outside_Policy
class IPS_class
ips inline fail-open
When I try to do "no ips inline fail-open" I get an "invalid input detected".If I try a no class IPS_class I get that is being in use.What can I do to clean up those lines?
View 8 Replies
ADVERTISEMENT
Jul 17, 2012
what is the best way to remove configs from ports (GigE or Fa) in a 6500 that we aren't using anymore (i.e. best way to return a port to default). Remove each line one at a time or is there a command to default a port?
View 2 Replies
View Related
Jul 23, 2011
Is it possible to remove the high encryption (k9) from an Asa and make it into k8 model?
View 1 Replies
View Related
Jun 5, 2011
I have this firewall working as active/standby. Everything seemed to be ok, but we noticed that confirgurations are not being replicated by saving configuration either copy run start or write. The workaround here is write standby command. Below the configs and stats, plus the show version, which is the same in both equipments:
Header 1
failover
failover lan unit primary
[Code].....
View 9 Replies
View Related
Apr 18, 2013
I'm trying to move some configurations over to an ASA5510 and some of the commands are a bit different than I'm used to (worked on old pix before)
I've configured the following on the device:
Outside interface: 65.66.64.34/28
DMZ : 65.66.64.49/28
Inside : 10.2.3.3/26
===========================
The current firewall has the below configured on it (old Juniper)
10.2.3.0/24 gateway 10.2.3.15 **10.2.3.15 is the IP for 3750 switch on the inside LAN**
10.0.0.0/24 gateway 10.2.3.4 **10.12.175.4 internal vpn- will remove later but thats a different discussion**
0 0 gateway 65.66.64.33 **to internet
10.0.1.0 gateway 10.2.3.2 **10.2.3.2 represents mpls traffic
[code]...
The current set up for this network has an mpls router and a vpn concentrator as part of the network my aim currently is to replace the juniper with an asa5510 the changing of the vpn tunnels will be for a different time:
work station ===> switch (3750) DG to =====> MPLS (vendor owned and managed) ====> non mpls traffic ====> vpn concentrator ===>firewall ===> router
The above will need acls to go with the routes, which I should manage ok just want to make sure the routing is configured properly
View 2 Replies
View Related
Sep 30, 2012
I have an issue with the LMS 4.0, i added manually the ASA Fws 5520 and 5510, and i see them there, but i cannot see the configuration, inventory and technology details.Telnet is deactivaved in ASA´s, ssh and snmp v3 are enabled.Routers and switches were added without issues.
View 3 Replies
View Related
Jan 16, 2012
I have one ASA5520 with version 8.4(3), and a few ACL rules defined. One ACL is permit traffic from one interface(EXT_SERVICE) to another interface(DMZ_SERVICE), if i change that rule to deny traffic, all new connections that match the rule is denied, but no the established connectios. ¿Why the established connections can pass the deny rule? ¿How I can change that? I need create a ACL with deny type and stop all comunications that is running and match the deny rule.
Running-config of my ASA5520:
ciscoasa# show run
: Saved
:
ASA Version 8.4(3)
!
hostname ciscoasa
enable password 8ay2wjIyt7RRXU24 encrypted passwd 2wFQnbNIdI.2KYtU encrypted names !
interface GigabitEthernet0/0
[Code] ........
View 9 Replies
View Related
Oct 28, 2011
I am trying to migrate checkpoint configs to ASA 5585 using SCT tool, this tool asking me to feed it *.W file from checkpoint which is suppose to be a rule definition file on CP, but I cant find it
View 14 Replies
View Related
Sep 19, 2011
After reading the post titled "ASA 5520 nat access-list query for internet access" I realized the object-group command could and should be used to make a more efficient and cleaner configuration. My current environment is very small and straight forward consisting of one FTP server in the DMZ. Though the guide: [URL] is straight forward, my inexperience hinders me from seeing how to use the commands effectively. A summary of the configuration is at the bottom of this post
Question: How can I clean up my current configuration? I have two references to the same server, dmz-rdp and dmz-ftp, created for port forwarding ports 3389 and ftp through the outside interface. I can combine them into one object statement, right? for each port I want to forward through the outside interface?
object network dmz-rdp
host 10.10.10.4
nat (DMZ,outside) static interface service tcp 3389 3389
[Code]....
View 1 Replies
View Related
Feb 13, 2012
I have an access-list that was named "extended" (without quotation marks) and the ASA will not let me remove it.
I have tried everything I know to try and get it out, but I cannot remove a single line.
ASA(config)# no access-list extended line 1 extended permit ip host 10.1.1.1 host 192.168.1.1ERROR:<1> not a valid permission
ASA(config)# no access-list extended line 1 permit ip host 10.1.1.1 host 192.168.1.1ERROR:<1> not a valid permission
View 1 Replies
View Related
Mar 22, 2012
I am unable to remove an access list. Currently this this access list contains 4 lines of remarks. I was unsure if I was entering the command correctly and now I have 4 lines of "trash" that needs to be removed.
Symptoms:
The "sh run" command shows that I have access-list 100 defined.
The "sh access-list" returns nothing.
Process I have tried: config t
no access-list 100
no access-list remark Test (just trying anything at this point)
clear configure access-list 100 (This returns "Invalid input detected at '^' marker" and the '^' is under the 'e' in clear.)
So the "clear configure" command is not working. The "no access-list" commands does not return an error but does not remove anything.
What step am I missing? Let me know if I can provide any more information.
View 2 Replies
View Related
Aug 12, 2012
My devices configurations are not getting backed up.
View 1 Replies
View Related
Sep 7, 2011
How I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
View 1 Replies
View Related
Apr 24, 2012
We were having a discussion of ios firewall vs. asa for smaller clients(less than 50). On using ios firewall(zbf or cbac)and an asa 5505/5510. One of the arguments brought up on using ios firewall on the router is that a router will do an ip sla failover. I have configured a number of isr's for this and i know it works good.
View 1 Replies
View Related
Feb 19, 2012
I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies
View Related
Aug 23, 2011
setting up an ASA 5505 to be used as a firewall between a BT internet router(BTNet service) and a Cisco 3560 Lan switch. BT have presented me with a cisco 3800 series router with the following details:
Network Address Network Mask BTnet NTE Router LAN Address
There are 2 Gigethernet ports on the back of the router port Ge0/0 is connected to the BT NTE and the status light is flashing green. Int ge0/1 is connected into port int e0/1 of the ASA but i am unable to get any connection.
View 21 Replies
View Related
Feb 27, 2013
I'd like to see some REAL LIFE comparisons of ASA firewall throughput (a bit like this one for ISR G2 Routers - [URL].
The reason I ask is that I recently upgraded a firewall from an ASA5505 to an ASA5520 on a small network where the only outside connectivity was a single 10meg Internet circuit with an IPSEC VPN (not landed on the firewall but on a router) to another site.
When I swapped out the firewall the users noticed a big improvement. The firewall is not doing anything out of the ordinary - no IPS or VPN, just standard state full inspection.
View 5 Replies
View Related
Mar 2, 2011
how to connect UTP cable
View 1 Replies
View Related
Dec 22, 2011
Trying to set up a asa 5505 in transparent firewall mode. I cannot set the management ip address:
ciscoasa> enable
Password:
ciscoasa# config term
[Code].....
View 7 Replies
View Related
May 3, 2011
I have been working with ASA 5510,20,40,80 but not with 5505 this vlan and its interfaces are quite confusing.Just want to know how it works and its connectivity to Cisco Switch.Do i have to put the interface of the switch in the same vlan as i am creating the interface vlan in firewall ?Now the switch port connecting to this Eth1 interface should also be in the same vlan ? i.e vlan3 ?? or it will be in trunk ? The default configuration shows the eth0 with no access vlan and interface eth1 with access vlan 2... does it mean the eth0 is in vlan1 ? (Nativ Vlan ) ???
View 4 Replies
View Related
May 28, 2012
I have a cisco asa 5505 firewall. Is it possible to block secure websites in it like [URL]? I have already tried regular expression filtering but it filters only http traffic.
View 4 Replies
View Related
Feb 26, 2011
I am trying to configure our ASA 5505 so that our users can access our ftp site using [URL] while inside the firewall. Our ftp site is setup so that you can reach it by either browsing to the above url or by browsing to ftp://99.23.119.78 but we are unable to access our ftp site from either route while inside the firewall. We can access our ftp site using the internal ip address of 192.168.1.3.
Here is our current confguration:
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0 !interface Vlan2nameif ATTsecurity-level 0pppoe client vpdn group ATTip address pppoe setroute !interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveobject-group service DM_INLINE_TCP_1 tcpport-object eq ftpport-object eq ftp-dataport-object eq wwwaccess-list ATT_access_in extended permit tcp any host 99.23.119.78 object-group DM_INLINE_TCP_1 access-list ATT_access_in extended permit tcp any interface ATT eq ftp access-list ATT_access_in extended permit tcp any interface ATT eq ftp-data access-list ATT_access_in extended permit tcp any interface ATT eq www access-list 100 extended permit tcp any interface ATT eq ftp
[code]....
View 6 Replies
View Related
Nov 21, 2012
New to the ASA 5505 8.4 software version, but here is what I'm trying to do:
-Single static public IP: 16.2.3.4
-Need to PAT several ports to three separate servers behind firewall
-One server houses email, pptp server, ftp server and web services: 10.1.20.91
-One server houses drac management (port 445): 10.1.20.92
-One server is the IP phone server using a range of ports: 10.1.20.156
Basically, need to PAT the ports associated with each server to the respective servers behind the ASA 5505. Is anything missing from this config? Do I need to include a global policy for PPTP and SMTP? [code]
View 11 Replies
View Related
Apr 27, 2011
I'm integrating a Cisco ASA5505 with a Websense proxy. I have a configuration setup where we have four routers which are used for Internet access. There are two VLAN's - Guest and Private. What I would like to achieve is making the use of available bandwidth by load distribution via GLBP, and filtering users web traffic. Two routers will be used for a GLBP group in one VLAN, and the other two routers will be used for GLBP in another VLAN.The users are connected to a Cisco 2960 switch and are in their respective VLAN's. I'm planning a 802.1q trunk to a Cisco ASA from the 2960 switch, carrying both VLAN's.What I would like to know is if there is a CSC module (or similar) which has Websense installed on it, and if it is possible to setup the ASA5505 in transparent mode to filter the traffic in this way? Hopefully this would allow multiple users to take advantage of the additional bandwidth, and not be restricted by using a traditional proxy setup which where all web traffic would be originating from a single MAC address.
View 1 Replies
View Related
Jan 18, 2013
Platform: LMS 3.2.1 with RME 4.3.2 on Windows 2003.I'm having a problem with several devices that were backing up fine until this week - suddenly they aren't backing up their running configurations, but RME is fetching their startup configurations fine and VTP backups are fine. At first I thought it might be timeouts, so I used inline edit to incease the telnet timeout for a device to 180s. However, the job fails well within this time period (debug shows on i/o error?). My order of protocols is SSH, Telnet, TFTP. I took a stab in the dark that this suggested a database problem so I picked one at random and deleted it from DCR, and readded it and it worked. However, for the other 48 devices affected it did not.
I'm wondering if I need to do anything to the RME database to get things back to where they were? Do I need to reinitialize the RME database, and if I do that what do I lose? [code]
View 2 Replies
View Related
Oct 14, 2012
I would like to have a support on AIR-AP1142N-E-K9 configurations.How I can config this AP?
View 1 Replies
View Related
Sep 27, 2011
I was recently given a Cisco 7200 VXR and told to erase the stored configurations in it. how to do erasing of Cisco 7200 stored config else I might have to delete them line by line.
View 4 Replies
View Related
Jun 11, 2012
I like to know how I can save or export all of my devices configurations to an FTP server for example.Cisco Prime LMS 4.2 appliance.
View 4 Replies
View Related
May 20, 2012
What module is used to push configurations in LMS 3.2.1?
View 1 Replies
View Related
Aug 22, 2011
Here is my basic network layout for multicasting for Syn-apps
Multicast Source-->3750 SW (add PIM SM-DM? Yes/No)-->3845 WAN Router (add PIM SM-DM? Yes/No)-->T1-->2821 (add PIM SM-DM? Yes/No)-->3560 SW (add PIM SM-DM? Yes/No)
OK, in this is it necessary to configure "IP Multicast-routing" on the switches? Do I configure PIM on all interfaces that will handle multicasting (router and switches?) If PIM is enabled on the 3750 do I need PIM configured between the 3845 and the 2821 ? Do I configure the Auto-RP on the 3750 or the 3845 ?
View 3 Replies
View Related
Apr 30, 2012
I have an issue with my firewall,each time i configured a trunk port in the firewall and connect a sw 2960S with a trunk port also, all the interfaces in the Firewall go down ( virutal intertaces, inside, outside , dmz) , also another switch 3750 that is connected to another port in the firewall( access port only) it start to a new negotiation of spanning tree.What could be causing this problem? the firewall didnt sedn bdpdu i think the IOS of the firewall its a 8.2
View 3 Replies
View Related
Jun 12, 2012
we are planning on connecting a new aquired company to ours soon?We will connect the remote site to the HQ via a D3. I've been told we will need to have a firewall between them and us for a time. I was thinking of terminating the D3 connection at the remote site of 80 users. Can I use the asr as a firewall as well, to protect the HQ from the Remote site - or should I use a seperate appliance?I was thinking of a asa5505 but, am concerned with bandwidth limitations of the box?
View 1 Replies
View Related
Sep 11, 2007
I want to configure an ASA 5505 in transparent mode (7.x). Somehow, I got it to work.. but i need some kind of step by step description. I just want to connect it with outside on a route .. inside in my LAN. Its working now with one ASA. But in the Web Interface the Interfaces inside and outside are down.. but its working.
View 5 Replies
View Related
