I have a cisco asa 5520 version 8.2.
I found big problem with ping. I can't ping any internet ip with packet size bigger than 990.
I checked runing again. I see config every thing fine. I can't ping bigger than 990 byte.
C:Usersuaydinli>ping 172.17.97.2 -l 1000
Pinging 172.17.97.2 with 1000 bytes of data:
Request timed out.
Request timed out.
[Code]......
I am having trouble with our ASA5510. After upgrading the internal memory from 256 MB to 1 GB and upgrading the firmware to 8.4.2 we are experiencing that the ASA is running out of 1550 byte blocks. When that happens it is not possible to connect to the ASA by ADSM or SSH and new VPN IPSEC tunnels are not coming up. The only way I know how to fix this is to reload the ASA. This is happening every 2 to 3 days.
In the free blocks graph one can see that there is a loss of about 20 blocks per 10 minutes.
I cannot seem to ping from the outside of my 5520 firewall to an inside network. I have a single physical outside interface connected to a Layer 2 switch, with a laptop connected to it. This is on network 10.11.131.0/28. From there, I cannot ping to the inside interface (which is a sub interface on G0/0) with network 10.11.130.0/24/ For some reason, it doesnt work.
Now. I had access-lists in place, but have removed them for testing and it still doesnt work. I have set the security level of inside and outside to 100, and entered the same-security-traffic permit inter-interface command - still no joy. Below is the relevant configuration.
Inside Interface
interface GigabitEthernet0/0.96
description L3 Interface - Informational Zone
vlan 96
[Code].....
I have ASA 5520. I cannot ping the host(192.168.1.20) which is inside firewall from outside hosts. Inside host (192.168.1.20) is translated into (198.24.210.226) using static NAT.From outside host, I used "PING 198.24.210.226". Is it because I used dynamic PAT for inside hosts?
interface GigabitEthernet0/0nameif outsidesecurity-level 0ip address 198.24.210.230 255.255.255.248!interface GigabitEthernet0/1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0
[Code].....
I got 2 x 5520 ASAs configured in active/standby mode and they are connected to 2 x 4500 switches in which too configured for failover.Telnet to ASAs is allowed only via subnet 172.18.0.0./24
I can only ping and telnet to the active ASA from subnet 172.18.0.0./24 but not the standby But i can ping and telnet to both the active and standby ASAs within the 4500 switches.
i cant ping, cant open web page, and funny torrent run normaly, steam chat ok.
View 4 Replies View RelatedI'm trying to configure an ASA firewall (FW2) for syslog and tacacs and am experiencing strange behavior. Both the syslog and ACS server are on the inside of another firewall (CoreFW). Whenever a log message is generated on FW2 the request is dropped by CoreFW and message '%ASA-4-313004: Denied ICMP type=0, from laddr FW2 on interface outside-b2b to syslog01: no matching session' is displayed. The same thing occurs for tacacs.
It appears that the syslog and ACS requests are generating ICMP echo replies, which the core firewall drops since no session exists on a lower security interface. I have access lists configured on CoreFW to allow the syslog and tacacs requests.
FW2 is running asa825-k8.bin, CoreFW is asa824-k8.bin
I am unable to ping inside interface (Rin) to outside interface (Rout) of my Cisco ASA 5520 runing on ASA Version 8.4(1).
ASA Version 8.4(1)
!
hostname FW5520
[Code].....
I have installed quite recently a cisco ASA 5520 replacing a linux based firewall I have only 2 zones ..one is internal netowrk and other external the internal network has web servers, dns and mail server all having public IPs Every thing is OK but i have seen that if I try to ping an external server for example [URL] i cannot ping says
[sylvan@kmdns1 ~]$ ping www.yahoo.com
PING eu-fp.wa1.b.yahoo.com (87.248.112.181) 56(84) bytes of data.
--- eu-fp.wa1.b.yahoo.com ping statistics ---
6 packets transmitted, 0 received, 100% packet loss, time 5010ms
but I can ping from systems which are outside my firewall perfectly with the linux firewall i had before i could ping perfectly to yahoo from any of my internal servers?
Is there any way to boost the signal to cover a bigger area?
View 1 Replies View RelatedUnderstand they are using dfferent cat cable. Does Cisco equipment nromally all are 1000-T, how to check they are 1000-T or 1000-Tx, does cat 5 with 4 pairs already support GE speed.
View 2 Replies View RelatedI have two questions about ZBF on ASR1000 with Firewall and Flexible Packet Inspection license:
1 is IPv6 supported?
2 can I use police action in an inspect rule? I want to limit some protocols to low bandwidth. There is no police command in ZBF policy map.
I am looking for for details meaning of license because I cannot found the details install. The license call
FLASR1-FW-RTU(=)
that is used to enable the firewall function in ASR 1000 series. But I don't clear about what feature inside, it is because it only show the "firewall" from website. Is that same as IOS firewall?
Which IOS version for me3600 supports 4-byte BGP?
View 1 Replies View RelatedSending 5, 100-byte ICMP Echos to 1.1.1.2, timeout is 2 seconds:Success rate is 100 percent (5/5), round-trip min/avg/max = 16/20/28 msround-trip min/avg/max = 16/20/28 ms
View 12 Replies View RelatedWe want to get L2 traffic amount (bit/byte) passing through a cisco switch (6500/3560 ...) for a specific VLAN. it can be via SNMP or CLI ...How can we do that?
note: there is no L3 interface on swtiches.
i have an ASA 5520 ver 8.4 with the following config
WAN
207.211.25.34
Production
10.11.12.1 255.255.255.0
Mgmt
10.11.11.1 255.255.255.0
i need to create a peer-2-peer VPN to a remote site ASP16 from both Prod and Mgmt
what would my nat statement look like ?
currently i have the following but can only ping from Mgmt not Prod (ASP17 is an network object group that contain the Prod and Mgmt subnets )
nat (Production,WAN) source static ASP17_VPN ASP17_VPN destination static ASP16 ASP16 no-proxy-arp route-lookup
nat (Mgmt,WAN) source static ASP17_VPN ASP17_VPN destination static ASP8_Prod ASP8_Prod
i have a site to site vpn stablished, the vpn works fine (while is up), i have a cisco asa 5520 and the other end of the vpn is a jupiter device that for technical reasons needs to send a continuos ping and when it does not receive a reponse back it brings down the vpn tunnel and reestablish it again. while the vpn is up traffic flows perfectly but because i m unable to repond to the ping the vpn is brought down as reestablished by the jupiter device. the jupiter device pings the encryption domain which is an ip that is natted to the real ip in the inside network. this is my configuration of the vpn:
AAA.AAA.AAA.AAA is the ASA public ip in the outside
BBB.BBB.BBB.BBB is the jupiter device ip (part of the object group IP_LIST)
CCC.CCC.CCC.CCC is the nat ip on the ASA
10.21.0.164 is the real address in the inside(code)
CISCO ASA 5520 -K9 .Client can connects ASA server and get ip address(172.168.31.X),but can't ping ASA inside interface ip address and other servers in lan .
View 2 Replies View RelatedI have a need to Remote Desktop connect to company’s employees for support then they are abroad and using Cisco AnyConnect client.Cisco AnyConnect client connection works fine, clients can reach company’s inside network without problems, but I cannot make revers connection, I cannot Remote Desktop connect or ping VPN clients from companies inside network. I cannot ping clients from ASA too.I am using ASA 5520, Cisco Adaptive Security Appliance Software Version 8.4(3) Device Manager Version 6.4(7), and Cisco AnyConnect VPN Client 2.2.0133. Protocol Encryption- AnyConnect-Parent SSL – Tunnel DTLS-RC4 RC4 AES 128.
View 0 Replies View RelatedI have HQ side with ASA 5520 (8.4) & Branch Side with ASA 5505 Design
VPN LAN<------->ASA5520(8.4)----->Thomson Business TG628s----->Internet<--->ADSL Modem------>ASA5505(8.2)
Now on both modems UDP 500 & TCP/UDP 4500 ports are enabled I can ping from internal LAN of HQ to internal LAN of branch but I cant ping from internal LAN of branch to internal LAN of HQ
HQ ASA 5520 Side
ASA Version 8.4(3)
host name aljoaib-fw01
[ code]....
Branch side ASA 5505
ASA Version 8.2(5)
host name GTC- DMM- FIREWALL
domain-name ALJOAIB.COM
enable password 7pgp93AEPfHtDc5N encrypted
[Code]....
Both sides have static ip address.
I've just started a CCNA course and my lack of knowledge has me a bit stuck. My network is comprised of Cisco components and I'm semi familiar with them just from reading and looking through options. I currently am using a Cisco ASA 5520 on my network and I am trying to join another network via one of the interfaces. My network is 192.168.0.0 255.255.0.0 and my inside interface is 192.168.1.1 255.255.0.0. I enabled a second interface using a static ip of 10.0.0.1 with a subnet of 255.255.255.128. Connected to that interface, I have a Fortigate firewall at 10.0.0.2 255.255.255.128. I can ping just fine from the Fortigate network to the 10.0.0.1 interface on the Cisco ASA 5520 network, but I can not ping the 10.0.0.1 interface (or anything past it) on the ASA 5520 from any computer on the Cisco network. I've read that ACL's and NAT have to be done as well as enabling traffic between interfaces with the same security levels. (both interfaces have security levels of 100 and the option is checked to allow traffic).
Note: each network has it's own internet connection. The connection is to share information on servers on both networks with each other.
I have an ASA that houses 11 VLANs, and I am trying to add a 12th.One of the VLANs is for PCs that have internet only access.The new VLAN will be similar, but for multifunction printers only.VLAN 99 is for internet only and works fine, I can ping the gateway of 10.99.3.33 from any PC in that VLAN.I am creating VLAN 98, modeling it after VLAN 99, and I cannot get a PC in the vlan to ping the gateway of10.98.3.17.Both switch and ASA show the new VLAN 98 as UP, switchport is UP/UP.I have deleted and recreated VLAN 98 a few times, but I cannot get a PC VLAN 98 connectivity.Once it is working on the core switch, I will add it to the trunk to the IDS switches. VTP is not in use, everything is manual. [code]
View 4 Replies View RelatedOn my ASA5520 I am trying to do a IPSEC tunnel between two sites. When I ping the protected network on the other side I get this when debugging IPSEC:
IPSEC(crypto_map_check): crypt o map man map 20 does not hole match for ACL man1
Not too sure what this means...
We were using ASA-5520-K9 with ASA-SSM-AIP-20-K9 but recently found some hardware problem in our running ASA. Now cisco want to replace with ASA-5520-K8.
View 1 Replies View RelatedI am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:
[Code].....
I've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.
View 32 Replies View RelatedInternet ISP -> Juniper SRX 210 Ge-0/0/0
Juniper fe0/0/2 -> Cisco ASA 5505
Cisco ASA 5505 - >Inernal LAN switch.
1. Internet is connected to Juniper Ge0/0/0 via /30 IP.
2. Juniper fe0/0/2 port is configured as inet port and configured the Internal public LAN pool provided by the ISP. And this port is directly connected to Cisco ASA 5505 E0/0. Its a /28 pool IP address. This interface is configured as outside and security level set to 0.
From Juniper SRX, am able to ping public Internet IPs (8.8.8.8).
Issue:
1. From ASA am unable to ping public ip configured on Juniper G0/0/0 port.(/30)
2. From ASA no other Public internet IP is pinging.
Troubleshooting Done so far.
1, Configured icmp inspection on ASA.
2. Used the packet tracer in ASA, it shows the packet is flowing outside without a drop.
3. Allowed all services in untrust zone in bound traffic in Juniper SRX.
4. Viewed the logs when I was trying the ping 8.8.8.8 in ASA. It says "Tear down ICMP connection for faddrr **** gaddr **
I'd like to see some REAL LIFE comparisons of ASA firewall throughput (a bit like this one for ISR G2 Routers - [URL].
The reason I ask is that I recently upgraded a firewall from an ASA5505 to an ASA5520 on a small network where the only outside connectivity was a single 10meg Internet circuit with an IPSEC VPN (not landed on the firewall but on a router) to another site.
When I swapped out the firewall the users noticed a big improvement. The firewall is not doing anything out of the ordinary - no IPS or VPN, just standard state full inspection.
I have an asa 5520. How would I configure my dedicated management interface to be able to route off subnet while the firewall is in transparent mode?
View 1 Replies View RelatedI have 2 modules of FWSM in 6500 switch (failover).I need 5 context.When I use in routed mode (like in the picture) , I cannot ping the servers behind the firewall. (I have ping to FW context),In transparent mode, it is not happening.what is the problem with routed mode?
View 1 Replies View RelatedWe are going to impliment Spectrum (CA) in my network,i have ASA-5580-20 firewall now my spectrum server want to communicate with firewall,then only it will discover the firewall logs.Now the problem is my spectrum server is in MZ zone(10.10.10.45) security leval is 70 and my inside interface(10.20.20.101) security leval is 100.
I am unable to ping from spectrum server to firewall because of high security leval.How can i solve this problem,can i change my inside security leval to 69 then i think it will ping.
We are using the newest release of AD Agent (1.0.0.32.1, built 598). The ASA Firewalls 5520 are having the software release 8.4(3)8 installed.When somebody tries to connect thru the Identity based firewalls from a citrix published desktop environment (PDI) the connection is not possible. Checking the ip-of-user mapping on the firewalls (show user-identity ip-of-user USERNAME) mostly doesn't show the mapping of the USERNAME and the PDI the user is logged in. The user-of-ip mapping of the PDIs IP-address shows mostly other users, which then are used to authenticate the acces thru the firewalls.
What is interesting, that on the AD Agent using "adacfg.exe cache list | find /i "USERNAME"" i can't see the PDIs IP-address neither because it is mapped to another user.Is Citrix Published Desktop environment supported to connect thru Identity based Firewalls? How AD Agent, Domain Controllers and Firewalls are working together? On the firewalls with "show user-identity ad-agent we see, the following:
-Authentication Port: udp/1645
-Accounting Port: udp/1646
-ASA Listening Port: udp/3799
Why Cisco does use 1645 and 1646 and not 1812 and 1813?The Listening Port is used for what purpose? we tried the AD Agent modes full- download and on-demand with the same effect.