Cisco VPN :: ASA 5520 Cannot Ping From Management
Dec 5, 2011
i have an ASA 5520 ver 8.4 with the following config
WAN
207.211.25.34
Production
10.11.12.1 255.255.255.0
Mgmt
10.11.11.1 255.255.255.0
i need to create a peer-2-peer VPN to a remote site ASP16 from both Prod and Mgmt
what would my nat statement look like ?
currently i have the following but can only ping from Mgmt not Prod (ASP17 is an network object group that contain the Prod and Mgmt subnets )
nat (Production,WAN) source static ASP17_VPN ASP17_VPN destination static ASP16 ASP16 no-proxy-arp route-lookup
nat (Mgmt,WAN) source static ASP17_VPN ASP17_VPN destination static ASP8_Prod ASP8_Prod
View 2 Replies
ADVERTISEMENT
Apr 27, 2010
I have a cisco 6509 configured with a cisco NAM module. I have reset the config of the NAM module by the config clear command. Since this moment I can't no more ping the NAM module via the management port: OK via the 127.0.0.91 address and log in ok via the ios cli session command. [code] I have already tried to reboot the module via the ios cli hw module command and nothing better.
View 12 Replies
View Related
Jul 27, 2010
I have two ASA 5520 with 4 Giga interfaces and 1 management interface.
I need to use 4 interfaces four data traffic
1- Inside
2- Outside
3- dmz-1
4- dmz-2
The remaining will be the management interface only.How can I configure the Statefull failover and Management?
1- I used the management0/0 for The stateful failover.
2- I used gig 0 for outside
3- I used gig 1 for inside
4- I used gig 2 for dmz-1
5- I divided the gig 3 to two sub interfaces
a- gig0/3.1 for dmz-2
b- gig0/3.2 for Management and I defined it as a management-only
View 6 Replies
View Related
Dec 14, 2011
i have a site to site vpn stablished, the vpn works fine (while is up), i have a cisco asa 5520 and the other end of the vpn is a jupiter device that for technical reasons needs to send a continuos ping and when it does not receive a reponse back it brings down the vpn tunnel and reestablish it again. while the vpn is up traffic flows perfectly but because i m unable to repond to the ping the vpn is brought down as reestablished by the jupiter device. the jupiter device pings the encryption domain which is an ip that is natted to the real ip in the inside network. this is my configuration of the vpn:
AAA.AAA.AAA.AAA is the ASA public ip in the outside
BBB.BBB.BBB.BBB is the jupiter device ip (part of the object group IP_LIST)
CCC.CCC.CCC.CCC is the nat ip on the ASA
10.21.0.164 is the real address in the inside(code)
View 1 Replies
View Related
Feb 3, 2013
I cannot seem to ping from the outside of my 5520 firewall to an inside network. I have a single physical outside interface connected to a Layer 2 switch, with a laptop connected to it. This is on network 10.11.131.0/28. From there, I cannot ping to the inside interface (which is a sub interface on G0/0) with network 10.11.130.0/24/ For some reason, it doesnt work.
Now. I had access-lists in place, but have removed them for testing and it still doesnt work. I have set the security level of inside and outside to 100, and entered the same-security-traffic permit inter-interface command - still no joy. Below is the relevant configuration.
Inside Interface
interface GigabitEthernet0/0.96
description L3 Interface - Informational Zone
vlan 96
[Code].....
View 4 Replies
View Related
Apr 21, 2013
CISCO ASA 5520 -K9 .Client can connects ASA server and get ip address(172.168.31.X),but can't ping ASA inside interface ip address and other servers in lan .
View 2 Replies
View Related
May 13, 2013
I have ASA 5520. I cannot ping the host(192.168.1.20) which is inside firewall from outside hosts. Inside host (192.168.1.20) is translated into (198.24.210.226) using static NAT.From outside host, I used "PING 198.24.210.226". Is it because I used dynamic PAT for inside hosts?
interface GigabitEthernet0/0nameif outsidesecurity-level 0ip address 198.24.210.230 255.255.255.248!interface GigabitEthernet0/1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0
[Code].....
View 3 Replies
View Related
Dec 8, 2009
I got 2 x 5520 ASAs configured in active/standby mode and they are connected to 2 x 4500 switches in which too configured for failover.Telnet to ASAs is allowed only via subnet 172.18.0.0./24
I can only ping and telnet to the active ASA from subnet 172.18.0.0./24 but not the standby But i can ping and telnet to both the active and standby ASAs within the 4500 switches.
View 20 Replies
View Related
Jun 8, 2011
ASA 5520 to get it to authenticate VPN users against and Active Directory environment plus allow management access as well. I created a Dynamic Access Policy on the ASA stating that if you are a member of the Active Directory group "Managment" the continue. I chagned the DefaultAccessPolicy to "Terminate". So with that, VPN users cannot connect because they are not a member of that group, but the access to manage the ASA is allowed because of that policy.Is there a way through using Dynamic Access Policies that I can allow management access (SSH, ASDM, etc) by matching to a group membership and will allow normal users to VPN in successfully but not allow them access to managing the ASA?
View 1 Replies
View Related
May 5, 2013
I have an asa 5520. How would I configure my dedicated management interface to be able to route off subnet while the firewall is in transparent mode?
View 1 Replies
View Related
Jan 2, 2012
I have got ASA 5520. How to use the management port as a normal port on ASA. What are the basic reqirements for that.
View 3 Replies
View Related
Apr 18, 2013
I have a need to Remote Desktop connect to company’s employees for support then they are abroad and using Cisco AnyConnect client.Cisco AnyConnect client connection works fine, clients can reach company’s inside network without problems, but I cannot make revers connection, I cannot Remote Desktop connect or ping VPN clients from companies inside network. I cannot ping clients from ASA too.I am using ASA 5520, Cisco Adaptive Security Appliance Software Version 8.4(3) Device Manager Version 6.4(7), and Cisco AnyConnect VPN Client 2.2.0133. Protocol Encryption- AnyConnect-Parent SSL – Tunnel DTLS-RC4 RC4 AES 128.
View 0 Replies
View Related
Sep 28, 2011
I have a cisco asa 5520 version 8.2.
I found big problem with ping. I can't ping any internet ip with packet size bigger than 990.
I checked runing again. I see config every thing fine. I can't ping bigger than 990 byte.
C:Usersuaydinli>ping 172.17.97.2 -l 1000
Pinging 172.17.97.2 with 1000 bytes of data:
Request timed out.
Request timed out.
[Code]......
View 5 Replies
View Related
Nov 2, 2012
I have HQ side with ASA 5520 (8.4) & Branch Side with ASA 5505 Design
VPN LAN<------->ASA5520(8.4)----->Thomson Business TG628s----->Internet<--->ADSL Modem------>ASA5505(8.2)
Now on both modems UDP 500 & TCP/UDP 4500 ports are enabled I can ping from internal LAN of HQ to internal LAN of branch but I cant ping from internal LAN of branch to internal LAN of HQ
HQ ASA 5520 Side
ASA Version 8.4(3)
host name aljoaib-fw01
[ code]....
Branch side ASA 5505
ASA Version 8.2(5)
host name GTC- DMM- FIREWALL
domain-name ALJOAIB.COM
enable password 7pgp93AEPfHtDc5N encrypted
[Code]....
Both sides have static ip address.
View 22 Replies
View Related
Nov 29, 2011
we are having a firewall asa 5520 .we have connected the management port and inside port to internal network and dmz port to dmz network.now we need to configure tacacs and other management tool on dmz devices through management port. The problem is the management devices tacacs and other are placed in internal network.
View 2 Replies
View Related
Apr 17, 2012
I've just started a CCNA course and my lack of knowledge has me a bit stuck. My network is comprised of Cisco components and I'm semi familiar with them just from reading and looking through options. I currently am using a Cisco ASA 5520 on my network and I am trying to join another network via one of the interfaces. My network is 192.168.0.0 255.255.0.0 and my inside interface is 192.168.1.1 255.255.0.0. I enabled a second interface using a static ip of 10.0.0.1 with a subnet of 255.255.255.128. Connected to that interface, I have a Fortigate firewall at 10.0.0.2 255.255.255.128. I can ping just fine from the Fortigate network to the 10.0.0.1 interface on the Cisco ASA 5520 network, but I can not ping the 10.0.0.1 interface (or anything past it) on the ASA 5520 from any computer on the Cisco network. I've read that ACL's and NAT have to be done as well as enabling traffic between interfaces with the same security levels. (both interfaces have security levels of 100 and the option is checked to allow traffic).
Note: each network has it's own internet connection. The connection is to share information on servers on both networks with each other.
View 1 Replies
View Related
Mar 20, 2012
I'm trying to configure an ASA firewall (FW2) for syslog and tacacs and am experiencing strange behavior. Both the syslog and ACS server are on the inside of another firewall (CoreFW). Whenever a log message is generated on FW2 the request is dropped by CoreFW and message '%ASA-4-313004: Denied ICMP type=0, from laddr FW2 on interface outside-b2b to syslog01: no matching session' is displayed. The same thing occurs for tacacs.
It appears that the syslog and ACS requests are generating ICMP echo replies, which the core firewall drops since no session exists on a lower security interface. I have access lists configured on CoreFW to allow the syslog and tacacs requests.
FW2 is running asa825-k8.bin, CoreFW is asa824-k8.bin
View 1 Replies
View Related
May 30, 2012
I have an ASA that houses 11 VLANs, and I am trying to add a 12th.One of the VLANs is for PCs that have internet only access.The new VLAN will be similar, but for multifunction printers only.VLAN 99 is for internet only and works fine, I can ping the gateway of 10.99.3.33 from any PC in that VLAN.I am creating VLAN 98, modeling it after VLAN 99, and I cannot get a PC in the vlan to ping the gateway of10.98.3.17.Both switch and ASA show the new VLAN 98 as UP, switchport is UP/UP.I have deleted and recreated VLAN 98 a few times, but I cannot get a PC VLAN 98 connectivity.Once it is working on the core switch, I will add it to the trunk to the IDS switches. VTP is not in use, everything is manual. [code]
View 4 Replies
View Related
Jul 26, 2011
I am unable to ping inside interface (Rin) to outside interface (Rout) of my Cisco ASA 5520 runing on ASA Version 8.4(1).
ASA Version 8.4(1)
!
hostname FW5520
[Code].....
View 10 Replies
View Related
Nov 2, 2009
On my ASA5520 I am trying to do a IPSEC tunnel between two sites. When I ping the protected network on the other side I get this when debugging IPSEC:
IPSEC(crypto_map_check): crypt o map man map 20 does not hole match for ACL man1
Not too sure what this means...
View 11 Replies
View Related
Jun 14, 2011
I have installed quite recently a cisco ASA 5520 replacing a linux based firewall I have only 2 zones ..one is internal netowrk and other external the internal network has web servers, dns and mail server all having public IPs Every thing is OK but i have seen that if I try to ping an external server for example [URL] i cannot ping says
[sylvan@kmdns1 ~]$ ping www.yahoo.com
PING eu-fp.wa1.b.yahoo.com (87.248.112.181) 56(84) bytes of data.
--- eu-fp.wa1.b.yahoo.com ping statistics ---
6 packets transmitted, 0 received, 100% packet loss, time 5010ms
but I can ping from systems which are outside my firewall perfectly with the linux firewall i had before i could ping perfectly to yahoo from any of my internal servers?
View 5 Replies
View Related
Mar 31, 2012
I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
View 5 Replies
View Related
Dec 12, 2011
I set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
View 3 Replies
View Related
Jan 18, 2013
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies
View Related
Aug 15, 2011
When I ping an address from my windows machine, it succeeds, but when I ping to the same IP on my MAC OS X machine, it fails.
1. Why?
2. How to get successful ping on my MAC machine?
View 1 Replies
View Related
Jan 26, 2012
I installed window server 2003 in a old Pentium III server as a standalone test server. Now I want to use it as a print server and connected it to the domain. I can ping workstations and other servers from that test svr. But i cannot ping that test server from the work stations.
View 2 Replies
View Related
Mar 1, 2013
I had both a Westell 7500 and a Linksys Router working fine and had my 360 setup as an extender for Windows Media Center so I could stream TV, Music, Movies, etc from my desktop to the 360. Then I switched my modem/router out with a Zyxel PH5001Z
So now today I noticed that I can no longer find my desktop through the XBox. I have adjusted my firewall settings on the modem itself, even completely disabling it. UPnP is enabled for the 360 and the device is showing under my device table. At first I wasn't able to ping any network devices but after creating an ICMPv4 Firewall rule it worked fine. I've confirmed the XBox IP Address through Network Map, the Device Table on the modem and through Network Settings on the XBox. I've diabled my modem firewall as well as Windows Firewall, completely and I still can't ping my XBox or set it up as an Extender.
I have the XBox connected wirelessly using WPA2-Personal and it's operating in 802.11g/n mode.
View 19 Replies
View Related
Nov 2, 2012
We were using ASA-5520-K9 with ASA-SSM-AIP-20-K9 but recently found some hardware problem in our running ASA. Now cisco want to replace with ASA-5520-K8.
View 1 Replies
View Related
Feb 29, 2012
I have a strange issue on my ASA 5510 (8.4). I can't ping or connect to the VPN clients but the VPN clients can ping/connect to any inside resources. I have checked all the NAT extemtion entries.
View 3 Replies
View Related
Apr 10, 2013
What is VLAN Management
View 4 Replies
View Related
Apr 20, 2012
I have multiple remote sites connected back into my infrastructure via satellite. I'm building a GRE tunnel accross this satellite infrustructure to my user's routers. I'm using EIGRP through these tunnels and everything is working great as far as connectivity to my users is concerned. However, with each of these packages, I would like to be able to remotely manage the satellite modem. My problem is that these modems all have the same web management IP address (192.168.1.1:80) and I can't change them. I thought to myself, "too easy, this sounds like an excellant case for NAT!" Either I'm tackling this thing all wrong or something because I can't seem to get it to work. Here is what I've so far (IPs modified and extra info cut[CODE]
View 3 Replies
View Related
Jan 26, 2012
A small remote site is going to need a dedicated 10mb connection to our Main Campus. Probably an 10mb ELAN connection(not decided as of yet). The site will be small - no bigger than 2500 sq feet with small walls possibly. Only one VLAN will be needed and we won't need any voice applications or back-up WAN ports. The site will provide connectivity for approximately 15 people. I've been looking at the 800 series routers for a solution. Do you think the 860 with the built-in 802.11 AP will suffice? I have a couple of concerns:
Does the 860 have CLI management?Will I be able to create a secure, encrypted tunnel between the 860 and a 2811 router on our Main Campus side? The 2811 has a 10mb ELAN secure tunnel on one interface already. I will purchase another interface card for this new, remote site VPN connection.Will the built-in AP give me coverage for the sq footage? I understand that there are extenuating circumstances to be concidered but, generally speaking?
From the video spec I viewed, the presenter said it had "basic security". What does that actually mean? This concerns me, as I want to built a secure WAN connection.Finally, does the 800 series fit this application or are there other Cisco products I should consider?
View 0 Replies
View Related
Dec 14, 2011
I have installed successfully installed and configured LMS 4.0 and every thing was okay until the customer decided to change the server IP address without notifying any one.
so i have returned the server to its original ip address since nothing worked after they changed the IP, but even after restoring the old IP address the device descovery is okay, but when i navigate to the devices management nothing appears in the all devices drop down menu and the remaining menues also.
i have tried to restart and to start a new device discovery also i have tried to run a data collection but nothing changed.
still stck on the devices are not appearing in the device management tab.
View 1 Replies
View Related
