Cisco Firewall :: PIX 525 Rebooted But Cannot Start

Mar 27, 2012

Today my colleague add 2 lines of access-list to our PIX 525.  After 10 minutes, my firewall was rebooted and until now can't start.  The booting process as listed below.
 
The questions are :

1. What is my OS version? Flash?

2. How to remove those 2 lines (reset the config to default)?

Booting process
================
Rebooting..þ
Wait.....
 
PCI Device Table.
Bus Dev Func VendID DevID Class              Irq
00  00  00   8086   7192  Host Bridge
00  07  00   8086   7110  ISA Bridge
00  07  01   8086   7111  IDE Controller
00  07  02   8086   7112  Serial Bus         9

[code]....

View 1 Replies


ADVERTISEMENT

Cisco Firewall :: ASA 5510 / Outbound Internet Access Not Allowed When Syslog Server Is Rebooted

Jun 27, 2011

I have recently setup Splunk to receive my syslog messages from my ASA 5510.  In the past I used kiwi without observing this issue, but I needed more features than kiwi had available.  Anyway, anytime I stop the splunk service my asa does not allow any outbound connections to be established. 

View 2 Replies View Related

Cisco Firewall :: ASA 5505 Doesn't Start

Feb 28, 2013

I write because my Cisco ASA 5505 doesn't start.When I connect power to the device, immediatly "Power" green Led turn on but "Status" Led is orange and not change.There is not data by Console cable.I try by another Power Supply but nothing.

View 1 Replies View Related

Cisco Firewall :: Unable To Start ASDM Version 1.5 (50)

Aug 14, 2011

I recently upgraded Java to JRE version 1.7.0 and now when I try to login to the ASA 5510, I get the following message in the java console log.Exception in thread "AWT-EventQueue-0" java.lang.ClassCastException: sun.security.ssl.X509TrustManagerlmpl cannot be cast to com.sun.net.ssl.internal.ssl.X509ExtendedTrustManager at com.sun.deploy.security,X509ExtendedDeployTrustManager.<init>(Unknown Source)

View 5 Replies View Related

Cisco Firewall :: 5505 ASDM 7.1 Fails To Start On MacOS

Feb 6, 2013

I have an ASA-5505 which I have been managing using ASDM from a PC and a Mac.I just happens that the Mac has not been used in a little while and when I tried to use ASDM on it, it fails.I've had a trawl through various posts and release notes (after updating various components in the process, incl Java with all the diabling/security updates of late) but am still having the problem and this is where I'm at:

- the ASA runs v8.4(2) and ASDM 7.1(1)52
- release notes state that ASDM 7.1 should work on Java 7 on Windows 7 and MacOS 10.7
- ASDM starts fine on my Windows 7 PC running Java 1.7.0_13
- I am also running Java 1.7.0_13 on MacOS 10.7.5
- on MacOS, ASDM starts, asks for credentials, download/refreshes the cached app... and then crashes with the following exception message:
 
The root cause of the issue seems to be that a Java class called apple.laf.AquaTableHeaderUI is not found..Now, I don't know much about Java, but that seems to be an Apple UI related class - I presume that it would be good to use this to give ASDM a more native look and feel, but why on earth is there no fallback? or am I missing something?

View 4 Replies View Related

Router Has To Be Rebooted All The Time?

Oct 4, 2012

I have 6 computers on a home network. 5 of them are running Windows 7 Home Premium and 1 is running Windows 7 Ultimate. My ISP is CBeyond, a T1 signal. I consistently get the "Windows has detected an IP address conflict" error on my screens and I have to reboot my router at least 5 times a day to get the wireless signal to connect. My laptop states that it is connected but I get the yellow triangle telling me that it has no internet connection. The firmware on the router is the latest version. DHCP is enabled on the router and set to Obtain Address Automatically and Obtain DNS automatically.

I can't figure out what's wrong. The 6 computers are wired through a switch connected to another switch connected to the router. This is also how the computers are connected on the network. I have several switches connected to the router. How do I configure the router so it doesn't have to be rebooted all the time to access the internet wirelessly?

View 14 Replies View Related

Cisco WAN :: Router 7204 Rebooted Unexpectedly?

May 8, 2011

One of our Routers 7204 rebooted unexpectedly. I try to access Output interpreter but is not working. The output from our router is the following:
 
 WAN-ROUTER#sh version
 Cisco IOS Software, 7200 Software (C7200-ADVIPSERVICESK9-M), Version 12.4(15)T2, RELEASE SOFTWARE (fc7)

[Code].....

View 7 Replies View Related

Dlink Router Constantly Has To Be Rebooted

Mar 7, 2013

This is an ongoing problem and I am wondering if a firmware update is called for. We have had the router for some time and to the best of my knowledge nothing has been done to fix the problem except the old "unplug for 10 seconds" routine.There are now four users on the home network with multiple devices.

View 1 Replies View Related

Cisco Switching/Routing :: Nexus 5010 Rebooted Itself?

Feb 9, 2013

Our Data Center Switch (5010) rebooted itself today, underneath the captured screen
 
NX5010-1(config-vlan)#
Broadcast message from root (console) (Sun Feb 10 14:22:41 2013):
 
The system is going down for reboot NOW! 
 
NX5010-1# sh system reset-reason
----- reset reason for Supervisor-module 1 (from Supervisor in slot 1) ---
1) At 740938 usecs after Sun Feb 10 14:22:41 2013
    Reason: Reset triggered due to HA policy of Reset
    Service: nohms hap reset
    Version: 5.0(2)N1(1)

[code]....

View 2 Replies View Related

Cisco Wireless :: 5508 - AP Unable To Get IP Address After WLC Is Rebooted

Aug 20, 2012

I had configured a Cisco 5508 series WLC. The APs used are Cisco 3502 LAP. The APs are configured to use DHCP for this ip addresses.
 
We had configured the DHCP server on the 2 Windows AD server previously and the APs were not able to get an IP address when the WLC was rebooted. To isolate the cause, we configured the DHCP server on a cisco 6500 switch. When we reboot the WLC, most of the APs are not able to grab an IP address. We had to remove and reconfigure the DHCP pool on the cisco 6500 for the APs to capture the IP addresses.
 
My colleague had feedback that they gotten a message that the DHCP pool had been used up. We tried to do a "show ip DHCP pool" but the switch did not recognise the command. IOS version used is Version 12.2(50r)SYS2.
 
We had a problem with the wireless client getting ip addresses from the windows DHCP server previously but problem was resolved after we disabled the DHCP proxy on the WLC.
 
What we are curious is why was the DHCP pool fully used on the Cisco switch and how could we check the number of addresses used other than running "show ip dhcp binding" and doing a count of the IP addresses?
 
Also why did we have to disable the DHCP proxy on the cisco WLC for the wireless clients to be able to get an IP address from the windows DHCP server?
 
We seem to be facing a number of problems with the DHCP functions for the wireless setup.

View 5 Replies View Related

Linksys Wireless Router :: E1000 Needs To Be Rebooted To Be Seen On LAN

Sep 3, 2011

With the E1000 tthe wireless devices they seem to work just fine, I can access the internet just fine.
 
For my desktop PC in oder to use the router to get on the internet or to even use the Cisco Connect to check the router, the E1000 needs to be rebooted. I am unable to access the router otherwise. I have tried 3 different LAN cards all with the same results. 
 
The latest firmware notes do not look like upgrading the firmware will work. My Router info from Cisco connect
 
Model name: Linksys E1000
Model number: E1000
Serial number: CVN21L422937
Firmware version: 2.1.01 build 5
Operating system: Windows 7 SP 1
Software version: 1.3.11006.1
Connection type (WAN): unknown

View 1 Replies View Related

Cisco Wireless :: 5508 - 350 WAPs Are Not Retaining WLAN-ID When Rebooted

Jun 28, 2011

I have 350 WAP (1142n) running of two WLC 5508 (IOS version 7). WLCs are not located on the same subnets/locations and are not configured as mobility groups. The vlan ids on both wlcs are not identical.

[Code].....

View 6 Replies View Related

Cisco Switching/Routing :: 4500 Rebooted When Creating L3 VLAN?

May 20, 2013

We have observed WS-C4507R-E got rebooted while creating the L3 VLAN ( while No shut).Is there any known bug for below IOS ?cat4500-entservicesk9-mz.122-40.SG.bin,

View 4 Replies View Related

Cisco WAN :: 7200 VXR Router Got Rebooted After Due Software Crash Dump

Sep 25, 2011

7200 VXR router got rebooted after due software crash dump.I have replaced NPE-G1 but still router is rebooting. Currently I am running with 12.4 (15)T 13 IOS.Crash Dump file is attached.

View 4 Replies View Related

Cisco Switching/Routing :: 3750 Get Rebooted And Now SFP Module Is Not Working

Mar 19, 2012

In my Cisco 3750 get rebooted and now the SFP module is not working.
 
It showing the following error message.
 
05:13:22: %PHY-4-CHECK_SUM_FAILED: SFP EEPROM data check sum failed for SFP inte
rface Gi1/0/26 
05:13:22: %GBIC_SECURITY_CRYPT-4-ID_MISMATCH: Identification check failed for GB
IC in port Gi1/0/26
 
What is the error message indicating and what is the solution for this.

View 1 Replies View Related

Wireless :: Internet Doesn't Work After Rebooted Laptop

Jul 2, 2011

my wireless internet does not work after I rebooted my laptop.I tried installing wireless internet but it failed.What do i do?

View 1 Replies View Related

RT-N56U Wireless Drop Every 5-10 Minutes After Router Rebooted

Dec 25, 2012

There are three RT-N56U routers in my family. I have one as does my dad and uncle. Bought all 3 about a year ago. They've been rock solid since.

However, my dad has been complaining of network issues, mainly lag and slow response. During Christmas yesterday, I took some time to troubleshoot it which ended in disaster. He was on an older firmware so I had updated it. After the update, the wireless would drop every 5-10 minutes after the router rebooted. I tried rolling back the firmware and there is still the same issue.I reboot the router, wireless comes up and within 10 minutes, the wireless is down.

Most of the clients on the network are iDevices. There are two iPod Touches, 4 iPad Mini's and iPad, two iPhones and an Apple TV, all wireless. Other than that, there is a PS3 and a bunch of wired clients. Looking in the routers logs, it appears that at least one device keeps requesting a DHCP request even though it has an address. Then at some point, the router spits out this error in the log: [code]

That error just keeps counting up, starting at 1 -- Based on google info it's related to wireless drops due to ASUS firmware issue with certain wireless cards. My guess is one of the new devices has a card that they don't support, causing this issue. I was stating to think, since he has so many iDevices on his network, an Airport Extreme?

View 2 Replies View Related

Cisco Switching/Routing :: Switch 3750 Of Stack Rebooted With No Reason

Oct 2, 2012

One switch of our stack of 8 3750 have reboot with no reason. Nobody was in the room server when it appears et there was'nt any electrical problem at this moment.

View 4 Replies View Related

Cisco Switching/Routing :: C6513 Module(ACE) Got Rebooted - Logs Attached

Feb 22, 2010

Our customer is having C6513 running with 12.2(18)SXF15a . One of the module (ACE20-MOD-K9) got rebooted with following error:
Feb 22 10:41:41.155 GMT: %OIR-SP-3-PWRCYCLE: Card in module 6, is being power-cycled off (Reset - Module Reloaded During Download)Feb 22 10:41:41.183 GMT: %C6KPWR-SP-4-DISABLED: power to module in slot 6 set off (Reset - Module Reloaded During Download)Feb 22 10:41:53.686 GMT: %OIR-SP-3-PWRCYCLE: Card in module 6, is being power-cycled off (Module not responding to Keep Alive polling)Feb 22 10:41:53.686 GMT: %C6KPWR-SP-4-DISABLED: power to module in slot 6 set off (Module not responding to Keep Alive polling)

Code...

View 4 Replies View Related

Cisco WAN :: 3750 - Access Switches Not Accessible When Stack Member Got Rebooted

May 20, 2012

We have got 2 3750 switches in the stack which are connected to access switches with 2 uplink ports .  each 1 uplink from each physical stack switch .
 
Due to some power issue our member switch got rebooted. After the reboot the access switches were not reachable through ping , but i was abe to see access switches in "show cdp neighbour" .   Then i rebooted the master switch and member switch one after other . after which i was able to ping the access switches.
 
IOS Version : c3750-ipservices-mz.122-35.SE5.bin

View 3 Replies View Related

Cisco Switching/Routing :: 3750 Router Lost Power And Rebooted

May 14, 2012

I am new to this and have ran into some problems. I butilt up my router I was able from the rom> prompt to get my router to boot from SLOT0:xxxxx

Then I did the copy command copy slot0:xxxxxxx bootflash:xxxxxxxMy router starts up fine. I did all my configurations and did my copy run start when I was done. As this is what I do on my 3750s.
 
My router lost power and rebooted and I lost everything it did not boot up to my last configuration.How do I save my configurations when I am done ? How do I get it to boot from that configuration every time?

View 1 Replies View Related

Linksys Wireless Adapters :: WMP600N Wouldn't Connect Unless Rebooted Router

Sep 9, 2012

I have been having problems with my Linksys WMP600N adapter and trying to connect to the internet.It started a few weeks ago in my old house, where it wouldn't connect unless I rebooted the router, or it would take a long time (over half an hour after being turned on to connect.)Then when I moved it got worse.At the moment it finds the wireless signals avaiable to it, but when I click connect it fails very quickly. It doesn't even try and connect, as it doesn't ask me for my wireless password.When I do get it connected, if I reboot the router and mess around, it kicks me off after a while, and then instead of showing the network available to connect to, shows it with a red cross beside, and I have to go and edit the security settings, or delete the profile and try and connect again. I have tried googling, but various different searches have turned up empty handed. My desktop is running Win 7 64bitThe rest of the specs are Core i7 920 CPU, Asus P6T Deluxe v2 Mobo, 12Gig RAM, Asus GTX 670 GPU, a Corsair SSD, 2 1TB HDDs and 1 2TB one.My Windows 7 laptop connects fine, and our Media Centre PC had some problems before I was here, but works fine now too.

View 3 Replies View Related

Linksys Wireless Router :: EA6500 Router Is Rebooted / Factory Reset

Apr 15, 2013

My EA6500 has been working fine for the last few months but a few days ago i upgraded to the latest firmware 1.1.28.147876 - this was done by an ethernet cable, not by wifi. However i've noticed the router reverts back to the previous fw 1.1.28.146856 when the router is rebooted or factory reset. I've repeated the fw upgrade process and also done a hard reset before upgrading the firmware but no avail. Normally after firmware is 'upgraded' the router reboots and i get the message "firmware successfully installed" but then on subsequent reboots the firmware reverts back. I'm using local router access but even using smartwifi gives the same issue. When upgrading fw, i've tried both options online & manual but again makes no difference.
 
 Don't really fancy calling Linksys support and going through 4 hrs of basic trouble shooting. Or perhaps Cisco have introduced a new automatic firmware downgrade option in their routers?

View 9 Replies View Related

Cisco :: WCS 7.0.172 Will Not Start

Jun 21, 2011

My WCS quit, apparently after the server was rebooted following Microsoft updates while I was on vacation earlier this week.
 
 WCS 7.0.172
Win Server 2003 R2 on VMware
4BG RAM
<6GB of 50GB disk space used.
   
After stopping WCS & rebooting:Health Monitor is running with an error.WCS is stopped.Database server is stopped Apache server is running After attempting to restart/start WCS:Health Monitor is already running.This was a clean install/upgrade a few weeks ago.  7.0.172 wouldn't install on top of the previous version so I had to uninstall, install and restore.  WCS had been solid ever since.

View 10 Replies View Related

Cisco :: WCS Version 7.0.164.0 Won't Start

Jun 22, 2011

WCS fails to start with a Tomcat error , see below ;See launchout below - without re-installing WCS
 
Checking for Port 21 availability... OK
Checking for Port 8456 availability... OK
Checking for Port 8457 availability... OK
Checking for Port 1299 availability... OK

[code]....

View 8 Replies View Related

Cisco :: LMS 3.2 Services Do Not Start

Oct 26, 2011

LMS does not start, although the services seem to be started. Find attached the pdshow output and let me know what more you need me to send.

View 3 Replies View Related

Cisco Switches :: How To Start With LACP On Two SG 200-50

Apr 24, 2012

I've two SG 200-50 and I need to use LACP? What should I do?

View 3 Replies View Related

Cisco :: Campus Manager 3.3 Does Not Want To Start

Dec 12, 2011

UTLite33.exe from Campus Manager 3.3 does not want to start, it gives the following:

"UTLite33.exe is not a valid Win32 application".

View 1 Replies View Related

Cisco :: LMS 3.2 CTM JrmServer Process Does Not Start

Jan 1, 2011

We have LMS 3.2 Bundle that installed on Windows server 2003 OS. I was found that CTMJrmServer service doesn’t coming up. After searching on forum and trying some solved issues my problem still exist. Hostname of server was changed before with hostnamechange.pl script and it was integrated with ACS before but now it’s on Local login mode. Here is my Bundle Version:
 
1.  Campus Manager 5.2.0
2.  CiscoView 6.1.9
3.  CiscoWorks Assistant 1.2.0
4.  CiscoWorks Common Services 3.3.0
5.  Device Fault Manager 3.2.0 08 Aug
6.  Health and Utilization Monitor 1.2.0 08
7.  Integration Utility 1.9.0 08
8.  Internetwork Performance Monitor 4.2.0
9.  LMS Portal 1.2.0 08
10. Resource Manager Essentials 4.3.0.

View 13 Replies View Related

Broadband :: Unable To Start Rpc

Mar 19, 2012

How do you enable Window XP RPC,Had W32Blaster.worm and cleaned system, however Internet will not load lack of RPC ,Message; no or low connectivity.

View 9 Replies View Related

Can't Connect Via IE Unless Start Then Stop VPN

Feb 21, 2012

I boot my computer at my company and if I immediately try, I can connect to the internet with IE or Chrome'm on my company's network. A few minutes after computer start up, I can no longer connect to the internet (times out). However, if I then open VPN, connect to the company network and turn right around and close VPN I now can connect to the internet. I've queried my IT group and they get a 'Huh?' expression on their face

View 5 Replies View Related

Cancel Linksys And Start Over?

Mar 30, 2011

I had to reboot my laptop and reset my wireless. Now I cannot sign on unless I am on the desktop connected to the router. How do I start over and reconfigure. I have another desktop and a laptop that I need to have access for internet.

View 1 Replies View Related

Intel PWLA8391GT Will Not Start?

Jan 24, 2013

I disabled my Intel PWLA8391GT because i wanted to test the onboard network, was not happy with the onboard network so i tried to switch back by enabling the drivers... well it then had a little yellow triangle with a ! in the middle it then told me that it could not start... I then restarted my computer and when i started it was in the unknow as pci device i then installed the drivers manually and it ran into the problem again..

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved