I have Static NAT on ASA 5520 for mail server and proxy server. I can use it from internet. now i want to Static NAT for 192.168.0.0/24. I mean 192.168.0.241-> 172.29.0.5, 192.168.0.242->172.29.0.6 so on.
I want when 192.168.0.10 hit 192.168.0.241 it goes to 172.29.0.5.
just simple static NAT. which command i need at ASA ? what is GW of 192.168.0.10 pc ?
We have a Cisco ASA 5520 and in order to conserve public IP addresses and configuration (possibly) can we use the same public IP address for a static NAT with two different interfaces? Here is an example of what I'm refering too where 10.10.10.10 would be the same public IP address.
-static (inside,Outside) 10.10.10.10 access-list inside_nat_static_1
-static (production,Outside) 10.10.10.10 access-list production_nat_static_1
ASA 5520 running 8.2
Is it possible to do static (inside,outside) with the outside address being IPv6 and the inside IPv4?
If yes, is it possible to do this in parallel with an existing static mapping that goes IPv4 to IPv4?
I have inherited an ASA 5520. In doing some auditing of the setup, I have noticed a Static Route that has the inside interface of the ASA as the Gateway IP. I am trying to understand the purpose of this route or why a route would be setup this way.
Example Static Route:
Inside 10.xx.31.0 255.255.255.0 10.xx.xx.10 (10.xx.xx.10 is the inside interface of ASA)
I have a asa 5520 with an outside and backup interface. I am trying to configure two static nat statements from the inside to the outside and backup interface. Here is what I have configured so far.
object network obj-10.1.1.254
host 10.1.1.254
object network obj-10.1.1.254
nat (inside,outside) static 172.25.10.3
I want to also use nat (inside,backup) static 172.25.10.3
We were using ASA-5520-K9 with ASA-SSM-AIP-20-K9 but recently found some hardware problem in our running ASA. Now cisco want to replace with ASA-5520-K8.
View 1 Replies View RelatedThere is a PIX firewall and it has this configured on it.static (inside,outside) tcp interface 3389 192.168.1.250 3389 netmask 255.255.255.255 0 0.This line of code works ok for port 3389 but I want all tcp ports to be translated. Not just 3389.
View 2 Replies View RelatedI'd like to see some REAL LIFE comparisons of ASA firewall throughput (a bit like this one for ISR G2 Routers - [URL].
The reason I ask is that I recently upgraded a firewall from an ASA5505 to an ASA5520 on a small network where the only outside connectivity was a single 10meg Internet circuit with an IPSEC VPN (not landed on the firewall but on a router) to another site.
When I swapped out the firewall the users noticed a big improvement. The firewall is not doing anything out of the ordinary - no IPS or VPN, just standard state full inspection.
I have an asa 5520. How would I configure my dedicated management interface to be able to route off subnet while the firewall is in transparent mode?
View 1 Replies View RelatedWe are using the newest release of AD Agent (1.0.0.32.1, built 598). The ASA Firewalls 5520 are having the software release 8.4(3)8 installed.When somebody tries to connect thru the Identity based firewalls from a citrix published desktop environment (PDI) the connection is not possible. Checking the ip-of-user mapping on the firewalls (show user-identity ip-of-user USERNAME) mostly doesn't show the mapping of the USERNAME and the PDI the user is logged in. The user-of-ip mapping of the PDIs IP-address shows mostly other users, which then are used to authenticate the acces thru the firewalls.
What is interesting, that on the AD Agent using "adacfg.exe cache list | find /i "USERNAME"" i can't see the PDIs IP-address neither because it is mapped to another user.Is Citrix Published Desktop environment supported to connect thru Identity based Firewalls? How AD Agent, Domain Controllers and Firewalls are working together? On the firewalls with "show user-identity ad-agent we see, the following:
-Authentication Port: udp/1645
-Accounting Port: udp/1646
-ASA Listening Port: udp/3799
Why Cisco does use 1645 and 1646 and not 1812 and 1813?The Listening Port is used for what purpose? we tried the AD Agent modes full- download and on-demand with the same effect.
I try to launch a LAND Attack against my firewall ASA 5520. Everything will work fine. But why, I think it should not work. I use a little tool where I can user a spoofed address, with a cluster shell and attack the firewall interface with the source of 127.0.0.1 ore the ip address of the interface as the source and destination. Then I get a cpu load of 89% with only two host. With IP tables I can use kernel processes to prevent this. But I don´t find anything for ASA.
View 1 Replies View RelatedTwo different WAN links get connected to the firewall via two routers.(Different ip subnets).I need to get this two wan streams seperatly to the core switches.Core switches sits.Active/Stanby senario. If the Active core goes down Stndby Core will have take over the traffic. My design is correct ,if not what do i need to change. ASA is 5520.
View 8 Replies View RelatedI have ASA 5520 installed. I want to use ntp server for firewall clock setting. I found one open-access ntp server (stratum 2) in Los Angeles:
[URL] 209.151.225.100
Can I use the following command to set ntp server?
ntp server 209.151.225.100 source outside.
communication between 2 vlans.i have 2 vlans
Vlan 100
ip add 1.1.1.1
!
!
!
Vlan 200
ip add 2.2.2.2
i want to make communication between 2 vlans on firewall 5520 ASA 8.2.
I have a serious problem with my corporate firewall, witch is an ASA 5520, fv 8.3, with 8 +1 interfaces. It suddenly started to crash every 10/20 minutes and rebooting alone.
First of all I checked system resources witch are in a very low usage state. I also checked interfaces errors, but nothing strange come out o from error counters analysis. I tried disabling logging and all the service policy rules configured, but nothing changed.
Nothing changed and firewall continue restarting by itself.
Last logs I received before crash were:
%ASA-4-711004: Task ran for 35 m sec, Process = Dispatch Unit, PC = 84a619e, Call stack =
%ASA-4-711004: Task ran for 35 m sec, Process = Dispatch Unit, PC = 84a619e, Call stack = 0x084A619E 0x084A6512 0x084A70E1 0x084A7987 0x084A7AAA 0x08558B9B 0x08558E8A 0x083D3518 0x083CA145 0x080659D1 0x089196D9 0x08919790 0x089FF711 0x08A27468
Here the sh crash info command on module 0, after last reboot:
[Code] ......
we are having a firewall asa 5520 .we have connected the management port and inside port to internal network and dmz port to dmz network.now we need to configure tacacs and other management tool on dmz devices through management port. The problem is the management devices tacacs and other are placed in internal network.
View 2 Replies View RelatedI have an ASA 5520 in my company which does all our NAT and Firewall access control. Currently there is a rule in place to allow an incoming connection on port 2222 from a specific ip address to allow access to a web app our developers created. This is a test before the web app is released live. Now the web app can communicate with the specific address and port but the incoming connection on port 2222 isn't getting through. Everything looks great in the firewall but how can I log any hits this ACL takes to identify any potential problems?
View 2 Replies View RelatedOur Local Network is behind the CISCO ASA Firewall.Whenever we are accessing to Client VPN server,it is getting connected but after few Minutes (May be 5/10/30 Min),the sessions are terminating. The same traffic through PIX is no issue , only with ASA Firewall. See the following Error and request you give the possible root cause for this.
2011-04-09 16:15:09 Local4.Info 172.16.1.68 %ASA-6-302016: Tear down UDP connection 87447908 for OUTSIDE:68.22.26.66/4500 to inside:172.16.9.10/4410 duration 0:27:49 bytes 18653
I have problem in the configuration of Cisco ASA 5520, IOS version 8.4. The connection is as follows: LAN network--> Firewall --> Routers with GLBP with virtual ip address. the clients can not ping the virtual interface of the GLBP group, but I can ping it from the firewall, and I can ping the clients from the firewall, I checked the packet tracer it gives :
Phase: 7
Type: NAT
Subtype:
Result: DROP
Config:
nat (inside10,outside) source dynamic LAN interface
Additional Information:(code)
Based on the network object below, I am looking for confirmation that It is good practice to use this natted object in my ACL applied incoming to the inside interface rather than have another object specifically for the object My_PC. I have tested and it does work, however this is my preffered option rather than having to create 2 objects, for the host and also the natted host.ASA(config)# object network My_PCASA(config-network-object)# host 192.168.33.2ASA(config-network-object)# nat (inside,outside) static 209.165.201.2
View 5 Replies View RelatedThe order in the older ios was nat 0 then static. With the new ios how is the static nat treated if i have a nat (inside,outside) source static Now I need to do some static one to one nats for some servers in the same subnet as the no nat
View 2 Replies View RelatedI am trying to configure static nat on ASA 8.3 but its not working.
here is the configuration:
object network Unix-Server
host 172.16.0.7
description Unix server
object network Unix-Server
nat (Inside,Outside) static 195.44.148.53
its basic configuration where i have my server on the inside network (172.16.0.7) which i want it to be natted to public ip to (195.44.148.53) .
i tried to add an access-list ingress direction on the outside interface to permit traffic from any to the public ip 195.44.148.53 but still its not working.
Need to know if ASA 5520 does Layer 7 firewall or not?
View 2 Replies View RelatedTwo days ago, we changed our old 525 with asa 5520 ( ver 8.2 ). Configuration is the same, except the version. It even retains the same global interface and static public ip address as the old device.All worked well during that period.
Yesterday, one of the http applications , not tested other day, was found not to be working. To test, we switched back to the old 525 , however nothing was working when we did that.
i am doind a policy NAT on the folowing scenarion.
acess-list policy_nat extended permit ip host 10.0.0.1 host 192.168.1.1
static (inside,outempresa) 170.66.53.1 access-list policy_nat
I understand that when host A 10.0.0.1 wants to connect to host B192.168.1.1 its going to be translated to 170.66.53.1 when host 192.168.1.1 wants to connect to10.0.0.1 the same entry will change the destination when the packet hits the asa from 170.66.53.1 to 10.0.0.1, is that correct ?
I just replaced a PIX 501 with a new ASA5505. I had a very weird problem and would like to know what caused it incase I run into it again. The setup is a DSL connection, with an old-ish speedstream DSL modem. Static IP, no PPPoE. I had a PIX 501, then two servers with static NAT entries on secondary WAN IPs. Everything was working fine on the PIX, I just duplicated the config over to the ASA. I swapped out the PIX for the ASA, and rebooted the DSL modem to clear out it's cache. After installation, NAT was working fine for the the global pool, but the systems with static NAT could not get online. I tried lots of different things to fix them, and they never worked. Finally I rememberd running into an issue like this a long time ago, in that the static NAT IP's wouldn't work without giving them a bump-start on the network. So I assigned the ASA each of my WAN IPs, one at a time, and tested them all. After that I went back to the original WAN IP, configured the static NATs, and they fired right up. why did my static NAT entries not work until I first assigned them to the ASA, then swapped back? I did reset the DSL modem when I swapped the firewalls, so I don't believe it was an ARP issue (unless it was an ARP issue at the far end?) I would like to know if there is something I can do differently with the devices or with the config to not have this issue again in the future.
View 5 Replies View RelatedI've been given 4 more public static ip's and would like to use one of them static ip's to point to my sharepoint box, for example i want to be able to access my sharepoint boxweb site externally:
212.xxx.xxx.01 - my public pix ip
212.xxx.xxx.02 - is my owa for email (https://xxxxxxx.net/owa)
212.xxx.xxx.03 - my sharepoint box (https://xxxxxx.net/sharepoint)
212.xxx.xxx.04 - not assigned
What command do I have to input on the Cisco Pix 515 to make that work?
I have a firewall which is conntect to a Cisco 870 router.
The router only allows one ip address to ssh into and it which is 7.7.7.7 but the interface which is connected to the router is on the firewall is a 2.2.2.2 and the router interface is a 2.2.2.1.
I can ping the router from the inside of my firewall, but I can't ssh into it at is has a access list which will only allow ssh from the ip address 7.7.7.7.
Would it be possible to do a static NAT which can translate the 2.2.2.2 to a 7.7.7.7 when I ssh into the router when coming from the inside?
I am having issues getting this to work. For email, I have mail.xxx.xxx DNS'd to 165.165.165.165. I want it to come in to 10.1.0.31. It needs to go out a cluster of 10.1.0.31, 10.1.0.34, or 10.101.201.31 but look like it came from the 165.165.165.165 address. I have set up static NAT for the inbound. I have set up the global PAT with an ACL group of the 10.xxx addresses. I have set this same method up on an ASA with no issues but it doesn't want to work on the PIX 6.3. What am I missing?
no fixup protocol smtp 25
object-group service NewExchange tcp
port-object eq https
port-object eq smtp
[Code] ....
I have configured Static NAT on ASA 8.4; and opened the telnet access through following configuration but it is not working. What mistake I am making in my configuration
interface Ethernet0/0nameif outsidesecurity-level 0ip address 119.36.105.210 255.255.255.240!interface Ethernet0/1nameif insidesecurity-level 100ip address 192.168.117.1 255.255.255.0
hostname(config)# object network Router_A
hostname(config-network-object)# host 192.168.117.2
hostname(config-network-object)# nat (inside,outside) static 119.36.105.211
hostname(config)# access-list ACCESS-TO-SERVER extended permit tcp any host 119.36.105.211 eq telnet
hostname(confi)# access-group ACCESS-TO-SERVER in interface outside
The host (router) 192.168.117.2 can access internet after this configuration but telnet is not possible from outside.
We have a Cisco ASA 8.3 and we're trying to configure NAT with multiple types of NAT.
We have a static NAT to an inside host from 1.1.1.2.
Internet Interface is on 1.1.1.3.
Users get NAT (PAT) on 1.1.1.4
VPN Subnet "No NAT" exclusion is from our LAN to various other locations.
Here are the relevent extracts from our configuration:
object network Server
host 172.19.0.80
nat (inside,outside) static 1.1.1.2
object network Inside_LAN
[Code]...
When the VPN exlusion ACL is applied to the configuration, PAT users have no connectivity to the Internet via TCP though UDP and ICMP traffic still passes. The VPN is operational. With the VPN NAT configuration removed, as expected the VPN fails, but users have connectivity to the Internet.
We have network topology:
Inside Network (172.168.1.0/27) --- ASA5510----- Outside network (192.168.10.0/24)
ASA5510 have: Inside interface: 172.168.1.30/27; outside interface: 192.168.10.254
And we config:
# object network obj_inside
# subnet 172.168.1.0 255.255.255.224
# nat (inside,outside) dynamic interface
[code]...
So, we í in from outside, we can't access web at 192.168.10.10?
I have a server having windows server2003 os. I have configured my web application on this server which is accessible over internet using static ip. But I found that there is an risk of viruses on my server. Thats why now I want to configure this server behind the firewall/Proxy as well as dont want to share my static IP.Is there any way to keep server protected using firewall / Proxy application which is free. And also tell me how to nat the static ip.
View 4 Replies View Related