I have upgraded to prime LMS 4.2.2 (from 4.0.1) and can not perform system or device upgrade. Using wireshark I can see why. it looks like LMS is trying to go to this old web [URL] to get software. I believe this was fixed years ago in bug CSCto46927.
Can I reapply bug fix CSCto46927 on 4.2.3 or is there another fix?
Linksys WRVS4400N Current Firmware Version: V1.00.16
Tried updating the firmware to either of the two version you seem to have available, but fails with:
"Upgrade file is not the correct type or version for this device. Upgrade failed. Please obtain the correct file and try again."
Tried this one: WRVS4400Nv2_v2.0.2.1.img
And this one: WRVS4400Nv2-fw-2.0.1.3-K9.img
Then spent 2 hours trying to find how to get support for this product. where I may download the correct firmware for this product?
I just purchased and installed this switch. It has firmware version 1.0.0.19 with boot version 1.0.0.1. I want to update te firmware to 2.0.0.8. Perhaps I am not doing something correct because when I try to update it I receive an error message that tells me the file is an illegal software format. Here is what I did. Under file format went to update firmware select http, update the chose the 2008.ros file. Start the upgrade but it fails.
View 1 Replies View RelatedI have been having problems with a 2106 WLC which seems to have developed a fault. I cannot console into the device (although I can console into the ap1131ag showing no fault with the RJ45 - 9 Pin) and the device is no longer showing up in any of the possible I.P ranges.
Its showing a power light and a status light on the front panel, the Ethernet ports light up like a Christmas tree when a device is connected and the power supply is putting out a solid 47.7v.
Has anyone experienced anything like this before and can anyone suggest anyway of breathing life back into it?
I have running a LMS master/slave installation with version 3.2.1 and patch for the cisco download running.Now I get on two of the three servers a NullPointerException if I want to go to the Device Update in CS.This is the output from stderr.log:
Feb 17, 2012 8:58:34 AM org.apache.catalina.core.StandardWrapperValve invoke
SEVERE: Servlet.service() for servlet action threw exception
java.lang.NullPointerException
at com.cisco.nm.xms.psu.ui.gui.model.ViewProduct.getAllProducts(ViewProduct.java:45)
at com.cisco.nm.xms.psu.ui.gui.model.ProductList.getAllRegProducts(ProductList.java:21)
[code].....
I did the installation the same way on all three servers.
we are running LMS 3.0.1. When I attempt to update the devices for RME I received the following error messages.
Number of Packages Selected for Install : 82
For Product(s) : Resource Manager Essentials
Install Invoked by user : admin
The Package(s) Selected for Install :
[code]....
Everytime I try to use the Cisco.com device update I receive the error in the attached file.
I'm not sure if this is related to me not configuring the proxy settings since we do not use a proxy server.
I've configured our CCO username and password only. Is there a known issue with using the web GUI to get updates using the cisco.com option?
i used the software center to download latest device packages, all downloaded to PSU_Downloads folder , i want to know how to install them with GUI if possible , as i tried to use CLI but it seems that i'm using bad syntax.
View 2 Replies View RelatedI have CiscoWorks LMS3.2 with RME4.3.1 and CS 3.3.0.
When I will update the devices and I go to Common Services - Software Center Device Update and I mark Resource Manager Essential then I receive this window:
Now I choose the Rtr2900 package (same problem for all six packages) and when I will download it, then after define the destination path for the file I see this window:
Then I have tried to download it manually with the following command: PSUCli.bat -p rme -d -dst c:psu_download -all
The six packages that are showed in the picture above were not downloaded.
I assume that there is an error on Cisco side because the size of the six packages is NA.
Or is there another possibility to download the package for the Rtr2900?
we have two ASA5520-AIP40-K8 in our office and we purchase IPS service for one only, can we also update the signature of second device before purchasing additional IPS Services for second unit
View 1 Replies View RelatedA few weeks ago, I bought a Linksys AE2500 wireless adapter, and it's worked fine up until a few days ago. A few days ago, when I turned on my computer, I could not connect to the internet. I've tried uninstalling and reinstalling the drivers, but I am denied every time; the message I get is "A device attached to the system is not functioning".I've tried connecting to the internet with my other wireless box I used prior to getting the AE2500 and I cannot connect with that, either. The only way I can connect on this computer is with an ethernet cable.
View 12 Replies View RelatedI have a router Cisco 2800, but always is in Rommon, the message show is:
device does not contain a valid file system
dir: cannot open device "bootflash:"
rommon 8 > dir usbflash0:
Checksum failed on c1840-usbfslib-m
Expected checksum: 91d6, calculated checksum: 4527
open: file "c1840-usbfslib-m" not found
open(): Open Error = -1
loadprog: error - on file open
cannot load the monitor library "bootflash:%c1840-usbfslib-m"
from device: usbflash0dir: cannot open device "usbflash0:"
We have an Asterisk/FreePBX phone system located behind an ASA 5505 device where we are having problems with sip inspection.
We connect to three different phone providers, and things works as expected for 2 of the 3 providers,but for the last one (Draytel) we are having problems with sip inspection.
The key difference about the VoIP provider where we are having problems is that they are using differetn servers for the voice (RTP) traffic than the server we are registered with to establish SIP sessions.
sip inspection is configured with the default out of the box options.The problems we see are this:
1. For ingoing calls sip inspection does not open the required pinhole to allow the traffic to flow through. As a result we can not hear the voice of the calling party, but voice from our side is passed through ok.As a workaround we have added and ACE allowing traffic in the used UDP (RTP) range from this VoIP providers ip addresses to pass through the ASA, and with that in place incoming calls work.
2. Outgoing calls doesn't work because sip inspection doesn't kick in, and as a result of this we forward internal ip addresses in the SIP / SDP body to the VoIP provider. I'm not sure whether this is a consequence of sip inspection not kicking in for this provider, or a result of having added the ACE for an ip ragnge that covers the ip address we register with.
As stated above sip inspection does work as expected for two other providers where all traffic goes through a single server.We actually have had this working with ASA firmware 7.2(4), but as that version intermittently had a problem where sip inspection would stop working (fixable by power off/on or a clear command), then we decided to upgrade.
I've purchased a wmp600n pci adapter january this year and installed it with no problems and did not encoutner a single problem with it until today. I use windows 7 64bit.
I've just came back from a 3 week absence and turned on my computer for the first time since i left. I notice that I have no wireless connection. So i go to network connections and realize that my wireless adapter dosent even show up..only my lan card. So i check my device manager, and under network adapters, i can see my wireless adapter, but with an exclamation mark next to it. I check the properties, and under the status box, it gives me this message.Your computer's system firmware does not include enough information to properly configure and use this device. To use this device, contact your computer manufacturer to obtain a firmware or BIOS update. (Code 35).
So i do what it says, and flash my bios to the latest version. After the update, I check the device manager, and the error message is still there. I check my wireless adapter driver version and it is v3.0.2, which is the latest version according to the linksys driver download webpage. I've tried uninstalling and re-installing the adapter but no luck there. I also checked to see if maybe there was a problem with my pci slot and that was not the problem because I was able to use my older wireless adapter.
We are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.
View 3 Replies View RelatedMy BEFSR81 is my primary router and has DHCP turned on. The router's DHCP range is set to accommodate 12 devices. I have three computers wired to it and their Host names (as specified in the set-up of each computer) show up in the router's DHCP device table. I also have two printers (one old Brother HL5250DN laser printer and one new HP Photosmart Premier C410a inkjet printer) connected and there are blanks where the Host name should go. I would like to be able to tell which printer is which when I am looking at the DHCP device table. How can I get a names associated with each printer's IP address in the router's DHCP device table? (The real problem is that the router seems to have both printers at the same IP address (192.168.1.100) and if I can get one of them to change I'd like to know which one it was!)
View 1 Replies View RelatedWhen I select Job Broser I get the following crash, LMS 3.2, server has been restarted but I continue to get the error. [code]
View 4 Replies View RelatedI'm running a Cisco 891 it has both crypto maps and ipsec VTI's running on the external interface. The cryto maps are for sites that do not have a cisco router and the Tunnels are for the sites that use crypto maps work perfectly fine. But I much prefer using unnels as it gives a routable interface, ospf works ect.
The tunnel interfaces will periodicly fail (Line protocol down) at no set interval, they will then not come back up again. To bring them back up I either have to shutdown and then re-enable the interface or run "clear cry ses rem *.*.*.*"
Logging with isakmp and ipsec errors provides the following:
55801: *May 1 10:31:16.015: ISAKMP:(0):Can't decrement IKE Call Admission Control stat incoming_active since it's already 0.55802: *May 1 10:31:16.015: ISAKMP:
[Code].....
My VRF Collector job has started failing. I have attached the contents of the vnmcollector.log file after setting debug level to DEBUG.
View 1 Replies View RelatedI've got a fully working 877w that I'm trying to get to boot from tftp, but I just can't seem to get that going.I have a tftp server running and can copy images back and forth without any trouble.I have this in my config:boot-start-markerboot system tftp c870-advipservicesk9-mz.124-24.T2.bin 192.168.1.200boot-end-markerDuring the boot process I get an error message that says there is a missing or illegal ip but I really don't see how that can be as my tftp server is 192.168.1.200 just like my config says.
View 16 Replies View RelatedMy tunnel had been running fine for a couple of months. Now, not so much.Here is some debug.
View 6 Replies View RelatedAny issues upgrading the IOS on a 921 router.How can i create a certificate for the new IOS? I've never had to do this for other IOS 15 upgrade?I've confirmed the IOS is not corrupt and if i upgrade the router in ROMMON the router boots correctly.
View 1 Replies View RelatedIm preparing a lab and I have 2 ASA 5520's. I have configured them for failover so the Primarys config will replicate over to the Secondary. They are connected via a 3560 switch. the switch ports are configured as access ports on vlan 1. Spanning-tree portfast is enabled
Firewall (Primary)
Cisco Adaptive Security Appliance Software Version 9.1(1) Device Manager Version 7.1(2)
Compiled on Wed 28-Nov-12 10:38 by buildersSystem image file is "disk0:/asa911-k8.bin"Config file at boot was "startup-config"
[Code].....
config collection is failing.in detail its partial success(config fetch is success but archieve is failed).
View 1 Replies View RelatedI'm currently unable to upgrade certain devices since Cisco Prime incorrect believes there is not enough room in the flash partition.For example.
Getting the following error messsage trying to upgrade some Cisco 871 routers: "Catastrophic - SWIM1200: Selected Flash partition requires minimum (28 MB) to upgrade selected software/image."The images are around 18 MB in size. Why does Cisco Prime thinks its 28 MB in size? Bug?
I have a rv016 that's been in 24x7 operation since I bought it a few years back. It is out of warranty. It is connected to three cable modems on WANs 1-3. Behind it are a bunch of PCs getting IPs via DHCP. There is a gateway to gateway vpn tunnel setup on wan3 to a rv082 at another site. There is a forwarding entry for http to an internal http server. Everything else is pretty much default.
The router is primarily used to aggregate bandwidth for uploading large numbers of photos. The systems behind the router initiate the uploads and the router automatically load balances the outgoing bandwidth.
This was all working fine until just recently. The ISP is Knology who is upgrading each of the 8m/768k cable modems to 25m/5m. They are also moving from DOCSIS 1 to DOCSIS 3. They are currently in the middle of this upgrade and have upgraded the modems to DOCSIS 3 as well as the speeds to 12m/2m. The problem is that the rv016 Network Service Detection, which is set to "Default Gateway" indicates that the modems fail randomly. Usually only one will be failed, but up to two will fail the Network Service Detection simultaneously.
Knology insists that there is nothing wrong with their modems. I have removed a modem from the rv016 when Network Service Detection indicates it is in a failed state and connected it directly to a computer. It will work, but it has a different IP address and default gateway. As soon as I connect it back to the rv016, it works there too, but on the original IP address and gateway. I've only tried this test this twice so far, so it is a bit inconclusive.
Speed tests behind the rv016 are the same as directly connected to one of the cable modems. The router works normally as it has for years. Nothing else is acting funny.
So my question is, is the rv016 failing or is the ISP having problems?
Backup failed on 2012/06/03 at 22:02:52. REASON: Unable to proceed with the backup operation as some files are being accessed by jobs. Reschedule the jobs such that the backup job does not coincide with other jobs.
Randomly the backup for lms 4.2 is failing. it has suceeded but majority of the time its failing. i have tried changing times but nothing seems to work. previously we were running 4.0.1 and had noproblems with the backup time.
Just found the bug
CSCtz29665
URL
I set up a connection from a laptop (Windows 7) that goes through a LAN proxy server to a secure ftp server (Windows Server 2003).The sftp server is assigned a public ip address.I opened the firewall at the destination and allowed port 22 traffic to the sftp server. Well, the connection is failing.I know for a fact the connection from the client laptop is making it to the sftp server.If I issue this command on the client laptop:
telnet sftpserver 22
The DOS screen clears and tells me the type of SSH server I'm connecting to. While this connection is still active, I logged into the destination sftp server and did a netstat command. I can see the address of the proxy server in the "Foreign Address" column of the netstat results. I also can see the proxy server address when I look at the Application Log on the sftp server, so I know the connection is making it to the sftp server.
I beleive the problem is the control port (return traffic) from the server back to the client. Something is being blocked or is misconfigured. I always thought the router negotiated the control port, and that the control port didn't need to be put into any firewalls.
For everybody else in the house the internet works fine on their devices, however, on my laptop and ipod it will often not allow me to connect for ages, but then finally connecting (without me changing anything)
View 3 Replies View RelatedI am able to use the lap top but not my desk PC.Browser keeps "failing" to recognize the DNS ? or my ports are blocked by a previous firewall ?
View 19 Replies View RelatedUPnP seems to be failing somewhere between a few hours and a few days. It will work as expected for a while after starting or restarting the router, but then trying to create any new UPnP mappings will fail, and the ones that have been already created usually stop working. The commandline client upnpc fails to locate the router automatically, and manually navigating to http://192.168.0.1:65530/rootDesc.xml in Chrome returns a connection reset error instead of the expected XML device description.I turned on debug messages in the logs, but there doesn't seem to be anything useful in there (though they also seem to be flooded with a bunch of IPv6 mDNS network hopping, so I'm going to try disabling that for a while and see if that works). I did update to 2.10 and still had the same issue with UPnP, however my wireless network kept going down (I guess a known issue) so I downgraded back to 2.07. After the downgrade, I reset the router and manually re-entered all my settings (i.e. I didn't import them).
View 14 Replies View RelatedThe problem: I need to track a bus from city to city in real time.I'm thinking of a gps device without screen or apps, it only sends the current location to a server. Is this possible? What device can be useful?
View 1 Replies View RelatedI am not sure why but when I try to connect with my IPSEC VPN client, authentications are failing. The ldap test passes on the ASA but when I try to login, the VPN client gives me authentication failure even though debugs show authentication was successful.User 'test1' should be able to authenticate based on group membership.User 'test2' shouldn't be able to.I already removed the attribute-map to see if that was the problem but I am still failing authentication.
View 9 Replies View Related
