What could cause this log message and put the port in errdisable?
15w2d: %ETHCNTR-3-LOOP_BACK_DETECTED: Loop-back detected on FastEthernet0/22.
15w2d: %PM-4-ERR_DISABLE: loopback error detected on Fa0/22, putting Fa0/22 in err-disable state
15w2d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to down
We have a number of 3750 stacks used as access layer switches connecting Siemens VOIP phones and then a PC that connects to the phone.
For example if I plug PC A to the phone that connects to port 13 I pick up an IP addressand all works as predicted now if I plug in PC A to any other VOIP phone that connect to another port on the same switch it goes in error disable state ITs like the switch is holding my PC mac address and locks it down with the port which in my case is Gi2/0/13.
interface GigabitEthernet2/0/13
switchport access vlan 726
switchport mode access
[Code].....
After reboot WLC , the switch port was err-disable , the cause is link flap after we reboot 3 times , the switch port link flap err-disable every time? We don't know why the WLC rebboot will cause it , it just normal action on device the WLC version is 7.4.100.0 link switch with access port , no port channel , no portfast.
View 11 Replies View RelatedI am looking to simply monitor Port-Security , Error-Disable and HSRP. I would like to receive an email when any of these are triggered.
Port Security - Port Is shut down
Err-Disable - Port goes into err-disable state (securedown)
HSRP - When HSRP standyby changes are detected
I need to receive emails with any of the able are triggered. What is the easiest way to do this? I know SNMP is the main option but I have never worked with SNMP and dont understand it too much.
Equipment:
2x Cisco 1921 series routers
3x Cisco 2960 POE switches stacked
I have implemented 802.1X with ACS 5.3 and switches 2960 without problem.The thing is that one port transitioned into err-disabled and I dont know why.I dont have any logs to see what caused this.Is there a command to see why this happenedWhat do you think could cause this?
View 4 Replies View RelatedI have port on cisco 3560 goes to error-disable,what is the cause of this issue,pls be noted this interface has BPDU Guard enable
View 3 Replies View RelatedI have a Catalyst 2950G when I activate the switchport port-security, but I want to empty the black list of mac address because every time I connect a device, the port is automatically désacative, here is the port configuration:
!
interface FastEthernet0 / 2
switchport access vlan 17
switchport mode access
switchport voice vlan 51
[code]....
I tried the following commands to clear the blacklist mac address of that port, but the problem is still relevant:
# Clear mac-address-table dynamic int fa0 / 2
# clear port-security all int fastethernet 0/2
# clear errdisable interface fa0 / 2 vlan
I want to use vertrigo localhost but due to port 80 enable it is not runing so how can i disable this port.
View 2 Replies View RelatedI can't download WAMP and am told Port 80 is blocking it. How can I resolve the problem?
View 1 Replies View RelatedHow do I disable the USB port in the 881 router?
881router#show usb port
Port Number: 0
Status: Disabled
Connection State: Disconnected
Speed: Full
Power State: ON
I'm using PfSense 2.0.1. What im trying to do is connect to a game server I have running here in my house. I can connect to it locally with 192.168.8.6 no problem. I have it port forward correctly so that the rest of the world can connect to it via my WAN ip address. The problem comes is I want to be able to connect to it with my WAN address so that if someone decides to follow me STEAM will show my WAN address not my internal IP address of the server im connected to. I have "Disable NAT Reflection for port forwards" UNCHECKED which is what I am supposed to do according to documentation from PfSEnse. But it still doesn't seem to work.
View 5 Replies View RelatedI have several SF300 switches deployed (SF300-08, SF300-24P). They are connected to IP Telephones (NEC) which communicate with the switch for auto voice VLAN on LLDP. The problem I am experiencing is that periodically the IP telephones are rebooted by the telephone vendor and when they do the switch puts that port into "Locked" port security mode and discards all traffic to the port. The IP telephones of course do not work. In other switch models, I have seen the ability to enable / disable port security switch wide or on a port by port basis. This model does not appear to have this feature. How to disable or why the phones would cause the switch ports to "lock"? There is usually one PC attached to each phone.
View 1 Replies View RelatedI have upgraded a couple of 2960G switches to 12.2.52SE and now discovered that TCP port 4786 is open on the switches.
I have looked in the document{URL}, trying to find a way to disable this function/port, but didn't find anything useful. Any way to disable this function/port?
Ask this question, if someone came across a 6513, one of the RJ45 ports are constantly falling.The question is how to disable logging on a specific portno logging event link-status does not work.
View 1 Replies View RelatedI have a Cisco 2960G switch and one of the ports was configured with srr-queue bandwidth limit 90 - I need to remove this bandwidth limiting from this interface. [code]
View 2 Replies View RelatedI am looking for a script or applet that will dis/enable an ethernet interface on Cat 6500 based on reachablity to an external destination. Reachability should be verified either directly by sending ICMP packets, or based on IPSLA status.
View 4 Replies View RelatedI am testing 2960 24 S with storm-control and Errdisable Port timer interval 60s , connected HUB on fa0/17 to make traffic / loop.After Strom Control detection the interface goes down thats ok after 60s they will try to recover the interface and going up although the loop is still there.For my understanding if the interface detect still a loop on that interface they will disable the port again for 60s and will check again. [code]
View 7 Replies View RelatedI have stacked WS-C3750E-24PD with Ten Gigabit Ethernet ports configured under ether-channel. It has c3750e-universalk9-mz.122-55.SE1.bin IOS installed on it. One of the Ten Gigabit Ethernet ports, goes to err-disable mode with following errors on that specific ports.
%SFF8472-5-THRESHOLD_VIOLATION: Te1/0/2: Tx power low alarm; Operating value: -31.0 dBm, Threshold value: -9.0 dBm.
%SFF8472-5-THRESHOLD_VIOLATION: Te1/0/2: Tx power low alarm; Operating value: -31.0 dBm, Threshold value: -9.0 dBm. (DROmx-1-1)
I have gone through some of CSC forums like {URL}. The workaround is to "Remove the X2 or SFP from the inactive up link port" which is not in my case.
In our company 3nos Cisco 3750 (WS-C3750-48P) access switch in stake mode. All port are assigned with voice and data Vlan also Avaya IP connected with this switches. From last few days tow port 2/0/7 and 2/0/8 is showing amber and status is showing err-disable. At Avaya end it is showing a message “ETHERNET WAITING” in phone dispaly. I try to connect laptop directly with these ports but it is showing "Cross Connectivity". [code]
View 4 Replies View RelatedCurrently it seems as our 3550's doesn't send traps when bpdu-guard sets a port in err-disable state. Or DFM doesnt recognize it.Is there a way to get a DFM alert when a 3550-port gets into err-disable state?
View 2 Replies View RelatedWe have a Cisco switch in each office and every now and then the port that has the D-Link Wireless AP (DAP-1522) connected to it goes to err-disable state. Actually sometimes even a regular port that has a cisco phone connected may also go to err-disable state (less often). So I have to telnet into the switch and issue shut and no shut command on that interface to get it back to life, then it works for a few days or weeks until it happens again. Any suitable configuraiton for that interface, that would prevent that from happening or a workaround ?
Here's the info:
Model: cisco WS-C3560-24PS and cisco WS-C3560-48PS
Image:c3560-ipbase-mz.122-35.SE5.bin
This is the log from one switch:
31w5d: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/2, putting Fa0/2 in err-disable state
31w5d: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 74e2.f592.f7f2 on port FastEthernet0/2.
31w5d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
And from another, which is almost the same:
5d10h: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/3, putting Fa0/3 in err-disable state
5d10h: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address d8a2.5e31.2cf6 on port FastEthernet0/3.
5d10h: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down
5d10h: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down
Here's the configuration of fe interfaces (they are all alike):
interface FastEthernet0/2
description Voice & Data Combo Port
switchport access vlan 11
switchport mode access
switchport voice vlan 15
[code]....
One of our Cisco 6500's fitted with a WS-X6704-10GE line card is showing a large number of Rcv-Err's on port 3. The port is disabled and no optic is even plugged in.Upon clearing counters, after every refresh the counters increment by 131070 -- so 131070 > 262140 > 393210 and so on. Seems a little strange that the buffer is full when nothing is connected.
View 3 Replies View RelatedI've got a pair of N7010's in a vPC domain with some FEX's attach running NX-OS 6.0.2. I am experiencing port failures on my N7K-M132XP-12L module the port got shut down due to internal errors with Error Disabled status and I am not able to bring the port back up. I am getting the following errors when I try to reset it. I am hoping is not hardware related as my vPC peer-link is on this module and I only have a single N7K-M1 32 XP-12L in each N7010. Replacing the module will be painful. [code]
View 7 Replies View RelatedI have a stack of 3750G's where the connection between switch 1 port 1 and switch 2 port 2 are down
Stack Port Status Neighbors
Switch# Port 1 Port 2 Port 1 Port 2
--------------------------------------------------------
1 Down Ok None 3
2 Ok Down 3 None
3 Ok Ok 1 2
I have ruled out the stackwise cable as the problem but would like to know which switch has the problem
a Customer ask me to configure a etherchannel between two Switches C3500 XL Version IOS 12.0 follow the first configuration what I done and the output error show me by switch:
Sw01(conf)# interface port-channel 1 % invalid input detected at '^' marker.
I have to do something before add an new port-channel interface ?? why the Sw01 does not accept my configuration ?
I've run in to this on 3750G's in a various sized stacks. We apply port security for a mac address on a single port (not existing on more than one port - that's a different issue that appears in multiple posts already).In this case:
1) We do a 'sho mac address-table and see that the device with the mac address in question lives on one port, port 1/0/x.
2) We apply mac port security for this exact same mac address to the same port it is already attached to. switch(config)#int g2/0/2 switch(config-if)#switchport port-security mac-address 001a.1ec8.abcd
3) Get this error: 'Found duplicate mac-address 001a.1ec8.abcd'.We again confirm that that is the only port on the entire switch that has this mac-address.Try the command again, same error.
4) We do a bunch of show commands, get in and out of the switch, go back and then try it again, and now it works, same command, same port and same mac address.
-Aging is default 300
-These are Cisco wireless AP's attached to the switch
-This occurs on different switches with different ports using different mac addresses, always same symptoms.
I have Counterstrike Scource and am wanting to setup a deticated server. I have a netgear router with 27015 port open and my nat type is open, however it keeps on giving me the "steam validation rejected" error. BTW it works fine on LAN, just not online.
View 2 Replies View RelatedI've Nexus 7010 switch installed in my DC. I've conncected Cisco router to one of the Ports. On the same port I'm getting following error message and hence, unable to form EIGRP neighborship.
DR-CORE-SW-S01-NEXUS7K %MODULE-2-MOD_SOMEPORTS_FAILED:
Module 1 (serial: JAF*******NGK) reported failure on ports 1/2-1/2 (Ethernet) due
to R2D2 : Speed patch failed - no frames transmitted in device 143 (error 0xc8f0
1273)
Recently I faced 1 issue in MLS 6509.MLS had all Gig modules in slots 6,7,8 taking System detected CRC error rate on port ASIC data bus exceed fatal threshold, ("System detected CRC error rate on port ASIC data bus exceed fatal threshold".) causing the module reset by the SUP. After this active SUP causing it to failover the standby. This process was continuing every few minutes resulting in the SUPs on MLS rolling.what could be the issue for Sup rolling reset?
View 1 Replies View RelatedThe router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
I'm trying to open certain websites but the browser gives me this message: "Network Error (tcp_error) A communication error occurred: "Operation timed out" The Web Server may be down, too busy, or experiencing other problems preventing it from responding to requests. You may wish to try again at a later time.
View 8 Replies View Relatedi'm currently studying at a college which has a website with a student intranet that is available to log in from any computer. So far it has been working well and I can log in on my home laptop and upload documents and look at presentations etc. Today for no reason when I try and log in I get the message Error Code 500: Internal Server Error and the webpage does no appear.I have had no problems previously and this has only happened today and yesterday, I went down to the college and accessed the website fine from the computers in the library but still no joy from my home computer.
View 1 Replies View RelatedI'm thinking about restricting 802.11b devices on my wireless networks and was wondering what is the best way to do so. As far as I am aware I can do it by either selecting "802.11a/g only" as the radio policy for each WLAN (Not shure what effect this will have on 802.11n though) or by disabling the following data rates 5.5mbs and 11mbs.
I'm wanting to continue providing support for 802.11g,n devices both 2.5ghz & 5ghz for n
WLC Software versions 6.0.199.4 and 7.0.220.0