I have implemented 802.1X with ACS 5.3 and switches 2960 without problem.The thing is that one port transitioned into err-disabled and I dont know why.I dont have any logs to see what caused this.Is there a command to see why this happenedWhat do you think could cause this?
View 4 RepliesWhat could cause this log message and put the port in errdisable?
15w2d: %ETHCNTR-3-LOOP_BACK_DETECTED: Loop-back detected on FastEthernet0/22.
15w2d: %PM-4-ERR_DISABLE: loopback error detected on Fa0/22, putting Fa0/22 in err-disable state
15w2d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to down
I have port on cisco 3560 goes to error-disable,what is the cause of this issue,pls be noted this interface has BPDU Guard enable
View 3 Replies View RelatedWe have a number of 3750 stacks used as access layer switches connecting Siemens VOIP phones and then a PC that connects to the phone.
For example if I plug PC A to the phone that connects to port 13 I pick up an IP addressand all works as predicted now if I plug in PC A to any other VOIP phone that connect to another port on the same switch it goes in error disable state ITs like the switch is holding my PC mac address and locks it down with the port which in my case is Gi2/0/13.
interface GigabitEthernet2/0/13
switchport access vlan 726
switchport mode access
[Code].....
I have a Catalyst 2950G when I activate the switchport port-security, but I want to empty the black list of mac address because every time I connect a device, the port is automatically désacative, here is the port configuration:
!
interface FastEthernet0 / 2
switchport access vlan 17
switchport mode access
switchport voice vlan 51
[code]....
I tried the following commands to clear the blacklist mac address of that port, but the problem is still relevant:
# Clear mac-address-table dynamic int fa0 / 2
# clear port-security all int fastethernet 0/2
# clear errdisable interface fa0 / 2 vlan
After reboot WLC , the switch port was err-disable , the cause is link flap after we reboot 3 times , the switch port link flap err-disable every time? We don't know why the WLC rebboot will cause it , it just normal action on device the WLC version is 7.4.100.0 link switch with access port , no port channel , no portfast.
View 11 Replies View RelatedI am looking to simply monitor Port-Security , Error-Disable and HSRP. I would like to receive an email when any of these are triggered.
Port Security - Port Is shut down
Err-Disable - Port goes into err-disable state (securedown)
HSRP - When HSRP standyby changes are detected
I need to receive emails with any of the able are triggered. What is the easiest way to do this? I know SNMP is the main option but I have never worked with SNMP and dont understand it too much.
Equipment:
2x Cisco 1921 series routers
3x Cisco 2960 POE switches stacked
The router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
I'm trying to open certain websites but the browser gives me this message: "Network Error (tcp_error) A communication error occurred: "Operation timed out" The Web Server may be down, too busy, or experiencing other problems preventing it from responding to requests. You may wish to try again at a later time.
View 8 Replies View Relatedi'm currently studying at a college which has a website with a student intranet that is available to log in from any computer. So far it has been working well and I can log in on my home laptop and upload documents and look at presentations etc. Today for no reason when I try and log in I get the message Error Code 500: Internal Server Error and the webpage does no appear.I have had no problems previously and this has only happened today and yesterday, I went down to the college and accessed the website fine from the computers in the library but still no joy from my home computer.
View 1 Replies View RelatedI'm thinking about restricting 802.11b devices on my wireless networks and was wondering what is the best way to do so. As far as I am aware I can do it by either selecting "802.11a/g only" as the radio policy for each WLAN (Not shure what effect this will have on 802.11n though) or by disabling the following data rates 5.5mbs and 11mbs.
I'm wanting to continue providing support for 802.11g,n devices both 2.5ghz & 5ghz for n
WLC Software versions 6.0.199.4 and 7.0.220.0
How do I disable fragmentation on a 2901 router? I want it to simply drop packets oversized packets.In my lab, I am trying to test various MTU issues. I'm trying to use a 2901 router to simulate the WAN equipment that my WAN provider would deploy in production. In production i'm expecting the WAN to only support an MTU of 1320 with no fragmentation at all.
View 2 Replies View Relatedthere are always some Traps more or less processed by LMS showing up in Fault Monitor View.Especially some Pass-Through or Unidentified Traps can be annoying if you want to keep the view clean.I wonder how to disable such Traps to not beeing displayd on the DFM Fault Monitor View?
View 1 Replies View RelatedI need support for wap4400n and I did not find it in the user guide and the administration guid.Is it possible to disable DHCP in this product? I want the wap4400n Access Point to distribute DHCP from the windows server.
View 1 Replies View RelatedI am trying to connect an SG200 to a customer's existing network. The customer does not want to receive any bpdu frames from the SG200. The customer's port has bpdu guard configured to err-disable their port upon receipt of a bpdu.
How do I completely disable spanning tree on the SG200 so that it does not send any bpdus?
On autonomous AP's one can disable the bright status LED using the "led ....." command. But how can I disable the LED on a LAP-1131AG? The AP hangs in a bedroom so the light is quite annoying.
View 3 Replies View RelatedI need to disable approxematly 40 different VPN profiles in our ASA5550`s without deleting them (need the ability to quickly activate them again if needed). I thought maybe i could disable IPSec for those profiles, but since the IPSec is an attribute for Group Policy, i cant do it - as many other profiles are sharing the same policy.
View 2 Replies View RelatedI'm currently setting my ACS 5.x for oridinary person to disable account if password not changed for certain date, But some VIP accounts need to exclude from this condition?
View 3 Replies View RelatedDo you now if it is possible to disable the xlate for some connection?
The ASA has some concurrent session limitation that, I think, is related to xlate connections.
As my firewall is not performing any kind of NAT, is it possible to disabe xlate for some connections.
I saw some options like nat exemption, but i not sure if the xlate still being create even if we don't have a NAT translation.
How can i disable dns doctoring on my Cisco 1921 router? Even if i use an external DNS my router facilitates me when i try to resolv addresses that are accessible externally and NATed through my router to the appropriate host. The router looks at its own NAT table and sees the IP i am trying to access and sends me right to the local IP. In my situation this is not good and i would like to disable this feature so that i can take the "outside" to this website.
View 5 Replies View RelatedWould like to report that WAP4410N Access Point cannot disable Wi-Fi Protected Setup (WPS). Tried both firmware 2.0.2.1 (19/JUL/2010) and the latest 2.0.3.3. No Disable option in both firmware.
If you do not change the default IP or default SSID for example, The WPS is disable by default. Once you change default IP and SSID for example, the WPS is then enabled. There is no Disable Option for WPS.
I am using lms 3.2.where I have added devices manually.Because discovery settings the device are taking some random ip updating the display and hostname.
I want to disable the full discovery settings..
I use windows xp and a BT home hub 2.0, i had my wifi set up so i could enable and disable wifi at my leisure. However every now and then i don't get the option to disable the wifi, so i normally have to reset my default admin password and enter my own password to eventually re use the enable/disabled option. But now i can't even do that so i'm stuck with permanent wifi. I did briefly manage to get the disable/enable option back by reset hub to factory settings but now it has gone again. What can i do? On my home network page where it reads devices currently connected to your BT home hub it has no devices detected for wireless.
View 1 Replies View RelatedI use VNC all over my LAN.How do I make sure that it's secure and disable connections comming from outside my LAN?would forwarding the VNC port to a non-existing computer work? or would that just break my local VNC connections?I currently have some using ultravnc and some using tightvnc
View 1 Replies View Relateddisable NAT on my Dir-655.I have another Firewall which NAT all my requiests and I do not want that my Dir-655 do this work.
View 14 Replies View RelatedDisable wrr-queue cos-map on 6509 interface?.I have the following config on one of the interfaces that i would like to remove:
[code]...
I am thinking of buying a SG200-26P switch and have a few questions:Is it possible to disable the PoE function on the 12 PoE ports?I need al the ports but only 6 with PoE.What happens when you connect a non PoE device to a PoE port?
View 2 Replies View RelatedI want to learn that,on cisco switch (2950,3600,6500 series) IpV6 default open? İf It comes open on default,how to disable?
View 19 Replies View Relatedhow to disable radio on the AP 1140 from NCS script .
View 5 Replies View RelatedI have WLC 4404 Controller with 180 LWAPP. i want to disable Broadcast SSID from some specified APs not all. is it possible to do that with 4404 WLC controller.
View 9 Replies View RelatedIs it possible to disable mac learning on a specific vlan in the nexus 5000?
View 4 Replies View RelatedWe have ciso asa 5505 and we are using one public ip of 155.155.155.9 , so i wanna disable to ping from outside this ip , but not effect our site to site and remote vpn connections ,the only thing i need is to disable the public ip to ping from outside.
View 7 Replies View RelatedI want to disable the MAC authentication that is configured in my Aironet 1200 Cisco Access Point, now set to "Local list only". I want that any wireless device can connect if the user knows the wep password.
I cannot find the option to disable the MAC authentication.