I use windows xp and a BT home hub 2.0, i had my wifi set up so i could enable and disable wifi at my leisure. However every now and then i don't get the option to disable the wifi, so i normally have to reset my default admin password and enter my own password to eventually re use the enable/disabled option. But now i can't even do that so i'm stuck with permanent wifi. I did briefly manage to get the disable/enable option back by reset hub to factory settings but now it has gone again. What can i do? On my home network page where it reads devices currently connected to your BT home hub it has no devices detected for wireless.
Once I had accessed Internet through Wi-Fi from my Laptop by giving the Security password. Disable and Enable wireless network is causing accessing the internet without asking security password every time.I want to access internet it should ask security password every time.
sometimes I let my friends to use my laptop but unfortunately they can see password of my wireless router which my laptop is connected to by going to this wifi network Properties and then to Security and then check in "Show Characters" box..so is there any way to prevent them from seeing my wifi network password in Windows 7?
I'm going to buy a WAG320N router modem.I've read the manual but I haven't found an answer to the silly question: is it possible to completely disable wifi, and surf in internet using the 4 lan port only?
Is there a way to quickly disable Wi-Fi on a N-150 from the router setup page? I have looked on my admin page but I don't see it. I just want to be able to turn the radio on and off from the PC that is connected via ethernet.
Region : NewZealand Model : TD-W8960N Hardware Version : V3 Firmware Version : 1.4.0 Build 111130 Rel.56405n ISP :
Just installed my new 8960 and it's working fine. However, I'd like to disable admin access from wireless, and only have that available via the LAN. I can't find anything that looks like it'll do that in any of the setup pages, is it possible? All previous wireless routers I've had have been able to do this.
My router a E4200. the thing is i want to disable the dhcp services from the router, because there are allready a dhcp server in my network. but if i disable the dhcp will the Guest wifi functions still work?
I use VNC all over my LAN.How do I make sure that it's secure and disable connections comming from outside my LAN?would forwarding the VNC port to a non-existing computer work? or would that just break my local VNC connections?I currently have some using ultravnc and some using tightvnc
I have implemented 802.1X with ACS 5.3 and switches 2960 without problem.The thing is that one port transitioned into err-disabled and I dont know why.I dont have any logs to see what caused this.Is there a command to see why this happenedWhat do you think could cause this?
I have a Blue Coat Shaper with four NIC cards. Two of them are connected, but I want to disable the other two just like a shutdown on a router or switch. Is there a command I can use to shutdown these NIC connections.
i tried to disable the ipv6 using the regedit and all and i restarted my pc but when i check the local network are connection and properties the ipv6 is still checked.
I have a home WI-FI network on windows 7 with an attached NAS drive for my media (plugged into the router).I was wondering how I would connect my work PC to the Wi-FI Network so it can access the media but disable the internet from only that PC.I have seen suggestions about blocking the work PC's IP in the router settings and something about MAC addresses, but was more hoping there was something simple I could disable in the network settings on the PC itself.
I am looking to disable 3 out of the 4 outlets on my router. There are 4 places where a cable can be inserted and I want to disable 3 of them so that internet service only comes out of one.
I'm thinking about restricting 802.11b devices on my wireless networks and was wondering what is the best way to do so. As far as I am aware I can do it by either selecting "802.11a/g only" as the radio policy for each WLAN (Not shure what effect this will have on 802.11n though) or by disabling the following data rates 5.5mbs and 11mbs.
I'm wanting to continue providing support for 802.11g,n devices both 2.5ghz & 5ghz for n
I have a n Ipad 4 with bad Wifi when connecting through a DL835, Firmware Version: 1.02. Other devices are fine and apparently i should try disabling WMM. I can see WMM but it's grayed out and i cannot disable.
What could cause this log message and put the port in errdisable?
15w2d: %ETHCNTR-3-LOOP_BACK_DETECTED: Loop-back detected on FastEthernet0/22. 15w2d: %PM-4-ERR_DISABLE: loopback error detected on Fa0/22, putting Fa0/22 in err-disable state 15w2d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to down
my internet connection is just connected to a router , it is OK to always disable and enable my internet connection? because every time i open my PC i always disable and enable the internet connection to make it work. how to make my internet connection work properly every time when i open my PC?
I need to disable the Internet Connection to a specified computer, without removing any wires or plugs. I have 3 computers which are connected to a SpeedTouch 5x6 (0843BH3B7) and a wire which then connects the router to the modem. Now, I want to disable the Internet connection for one of the computers from the software of the router.
i have window 7 instaled..my problem is that i use wateen usb for browing in office.where as my pc is conected with other pcs..when i disable the lan the wateen usb works but than i cant acess othert pcs..previouslyi was using same window and usb but there was no problem..after i have installed the window this problem has occured.
Using Windows 7 how would I disable the internet portion of my lan connection and use an usb air card instead? I'll still need to access the network files and folders using the lan though.
