Cisco Routers :: RVS4000 - Internet Access / Broadcast Error
Jul 29, 2012
I recently bought an RVS4000, and unfortunately forget the "if it ain't broke, don't fix it" rule, and flashed it to the latest firmware (2.0.2.7). Subsequent to doing that, it has been inconveniently dropping the connection to my ISP and completely locking itself up to a point where a manual reboot is required, usually about 4 hours after any outgoing activity (which usually means 11pm!).
Goggling my way round seems to suggest that this could be a firmware problem. The accepted wisdom is that I need to use the RVS4000 Upgrade Utility to get back to a lower version, so I have downloaded and installed V1.3 from the RVS4000 support area. However, though I think I followed the instructions (including trying setting the host PC to a fixed IP address, which was not supposed to be necessary), but I am consistently getting a "Broadcast Error" message, which I am guessing means that the utility and the RVS4000 aren't talking.
View 3 Replies
ADVERTISEMENT
Apr 14, 2012
Would there be some reason why I cannot change the Access Restriction to Allow? I also can't add anything into the Website Blocking by URL Address or the Website Blocking by Keyword. I can't type anything in the fields. I've tried rebooting, other browsers and even other computers but nothing seems to work.
View 14 Replies
View Related
Nov 27, 2012
I have recently purchased a RVS4000 router and am experiencing major downtime.Almost everyday the RVS4000 router losing internet connectivity. I noticed that when this happens I cannot login into the router from my pc which is connected to the RVS4000 network.The only way to restore connectivity is to restart the RVS4000 by disconnecting power and powering back up.The router's WAN is connected to my Cable modem.The RVS400 has two PC connected to it. (port 3 & 4) I have a Cisco 8-port switch connect to the RVS4000 with 3 additional PCs/devices on it.
View 6 Replies
View Related
Sep 11, 2011
I have 2 internet connections in my office one via Verizon Fios and another one via the local cable company. On the fios connection I have an RV042 VPN router and on the Cable company connection I have an rvs4000 router, I would like to know if there is a way I can connect the 2 so I can share a printer I have on one of the 2 networks from the other network without using the VPN feature, like via an ethernet cable connected between the 2 and some kind of static route maybe?
View 6 Replies
View Related
Apr 16, 2013
I have a RVS4000 and I would like to setup a Ping monitoring from the outside to a device behind RVS on lan network. I have created a rule to allow a service PING for range from WAN 46.xxx.xxx.xxx - 46.xxx.xxx.xxx to host 192.xxx.xxx.xxx but unfortunately this is not working. I can confirm that I can ping host 192.xxx.xxx.xxx from diagnostics on RVS.
View 2 Replies
View Related
Sep 27, 2011
I am trying to setup the VPN access using QVPN with RVS4000 but ran into difficulties I was able to connect to the router using QVPN from WAN, and able to access the router's admin page (my router's ip is 192.168.0.1). However, I am unable to access anything else on the LAN, including servers and printers. To make it clear, I am able to access all servers and printers when I am on the LAN! But nothing when accessing from the WAN via QVPN.
View 1 Replies
View Related
Aug 16, 2011
I've got an RVS4000 router with the latest firmware - V2.0.0.3, and just setup Dynamic DNS on it. However as I access the url of the Dynamic DNS, I get pointed to the routers web backend/GUI, which is natural as it's situated on port 80 of the router.
To prevent the whole interwebs from accessing my router's settings, I've quickly forwarded port 80 to a non-existent IP on my LAN. However this solution feels a bit fragile, so how can I ensure that only computers from inside my LAN can access the routers GUI?
View 1 Replies
View Related
Mar 9, 2013
I am trying to configure my RVS4000 to create my church's small network. I want to connect my internet DSL router on the WAN port and also segment my network with VLANs on the 4 LAN ports. I have port 4 connected to a wireless access point which is in VLAN1 for an open wireless network for any church member to access the internet through. I have a church server, printer and second access point on ports 1-3 in VLAN 34. All ports are untagged. I want the devices on VLAN34 which need confidentiality to be secure from the devices connecting to the internet from VLAN1 for open access but both VLANs need access to the internet..
My open wireless AP in VLAN1 has access to the internet on the WAN port.
None of my devices in VLAN34 have access to the internet. I have tried using inter-VLAN routing but that made operation worse so I disabled it.
View 1 Replies
View Related
Aug 22, 2011
I am able to connect to the RVS4000 remotely using QuickVPN, and can stay connected, however, once connected I cannot use the internet or see any of the remote computers via the network.
View 3 Replies
View Related
Mar 12, 2012
I am trying to access a device behind my firewall that needs to use port 9000. I have completed the single port forwarding page with the exterior and internal port but I cannot access the device from outside the firewall. Yes I did check the "enabled" box
View 8 Replies
View Related
Apr 8, 2012
Just recently purchased an RVS4000 to take the place of an old NetGear FVS336, which supported multiple NAT translations. It appears that the RVS4000 does not support this, any other models in the small business line support this? I only need this for a backup Internet connection?
View 4 Replies
View Related
Oct 17, 2012
I picked up an RVS4000 V2 and configured a rule to forward a Magic Packet to an internal system to wake it from a sleep state. Everything was working fine until I update the firmware to v2.0.3.2. I know it's not the the computer as I can wake it from Sleep internally without any problems. One thing I noticed is that the static IP for the computer in Sleep state gets lost in the ARP/RARP Table though the NIC is configured to respond to ARP requests in Sleep.
Has anything changed in v2.0.3.2 that requires a different configuration to get Wake on Lan working externally?
My Setup is
Computer
P8Z68 Deluxe/Gen3 onboard Intel 82579V NIC
Wake on Magic Packet: ON
Respond to ARP/NS requests without waking system: ON
RVS4000 V2 (v2.0.3.2)
Mode: Gateway
[code]....
View 1 Replies
View Related
Nov 17, 2012
This problem started happening a few days ago. Whenever I try to access [URL] on my computer that's not physically connected to the router and modem, I keep getting a 403 error:
You don't have permission to access / on this server.
Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request.
Apache/2.2.22 (Unix) mod_ssl/2.2.22 OpenSSL/0.9.8e-fips-rhel5 mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 Server at www.facebook.com Port 80 --
but I can access touch.facebook.com and m.facebook.com. If I use the computer that is physically connected to the router and modem, I can access Facebook fine. I've tried using CMDPrompt and releasing/renewing IP to no avail. I use the belkin n150 router with updated firmware and the linksys wireless-g pci adapter with v3 drivers. Never had an issue before up until now.
View 1 Replies
View Related
Mar 23, 2013
When I set up the Belkin F9K1102 as an access point I can no longer access it via the ip-address and it does not accept the new ip-address I've given it, but takes the ip-address 192.168.2.254, while my network is on the 192.168.1.XXX address series. The only way I can do this is by manually given the router a new address, then manually turn of the DHCP- server and finally move the internet cable from the WAN port to one of the LAN ports - but then the LED-indicator on the router is blinkin red.
View 2 Replies
View Related
Feb 4, 2013
Some background information of my current configuration.
VLAN 100
-Computer A
interface gi1/1/1
[Code]....
From computer A, i had run command prompt and ping 192.168.2.100(computer B) and successfully get a response. I had repeated the step but ping to a broadcast address (192.168.255.255) and it was unsuccessful.
View 5 Replies
View Related
Sep 22, 2011
I require a system that will support 3 VLANs, the VLANs are purely for containment of broadcast traffic and needs to support inter-VLAN communication between client devices. Would the following configuration work:
Port based VLAN on the SRP527W with each port connected to layer 2 switches serving each VLAN.
DHCP server on the SRP527W assigning IP addresses for each of the V LANS in different ranges. (eg 10.10.1.xx, 10.10.2.xx, 10.10.3.xx). Would there be any benefit upgrading the Router to a SRP547W?
View 2 Replies
View Related
Oct 4, 2011
For some odd reason, my playstation portable system will not allow me to access the wifi signal anywhere there is one available. The problem seems to be that the dns code is not correct. I need a COMPLETE & relatively EASY "walk-through" to fix this problem.
View 3 Replies
View Related
Feb 22, 2013
I live in an area where there are lots of wireless modems and since most broadcast on the default frequencies, here is often interference. I'd like to set my AC900 to broadcast on a fixed channel that is not often used, e.g. 2 or 3 or 8.
View 2 Replies
View Related
May 26, 2012
I am getting this message on my laptop for cable modem hookup as well as for my wireless saying unidentified network no internet?
View 15 Replies
View Related
Jul 27, 2012
I've had my DIR 615 router for quite some time. The hardware version is C1, firmware 3.01 originally. It's been fine for the most part (asides from connection issues now and then with the internet - which we rectified by unplugging modem and/or router). A couple nights ago we had a storm and the next morning the router would not connect to the internet. I tried unplugging the router and modem a number of times but could never establish a connection. The internet globe LED was originally orange but after I cut off the power, it never came back on. I tried a number of different cables between the modem and router and could not fix the issue. I bypassed the router totally and the internet works fine. After a lot of failed attempts, I decided to reset the router and reinstall it with the disc. I followed the instructions and kept getting error 322 that the router could not be found. I tried 3 different computers and 5 different wires to fix the problem but to no avail. I kept encountering the same error on each computer. Since the router can't be seen, I must bypass it totally to get any internet access so trying the online setup doesn't work because I can't connect to the router and then to the modem since there is no internet access. So now I'm stuck. I'm not sure if my router is damaged from the storm. All other lights work (LAN and wireless icon) but I can't get any internet access through the router. I'm not sure if I should just go buy another router or not. The installation checks out fine until connecting power to the router and then it can't be found.
I am running windows 7 and vista on different computers and laptops and used setup 4.1.7141.2
View 1 Replies
View Related
Mar 16, 2011
RSTP port role in the switches are flapping if broadcast data is flowing through the ring. Also I've tried applying broadcast suppression to all the port to 64kbps for ports of 100Mbps/1Gbps, All the devices I'm using are L2 switches.
View 1 Replies
View Related
Dec 29, 2012
F9K117 - I can't see my broadcast ssid for the 5ghz band. Is there anything I can do?
View 3 Replies
View Related
Mar 16, 2012
I cannot connect to the internet. After running troubleshooting i receive and error message."Local area connection 2" doesn't have a valid ip configuration.
[code]...
View 4 Replies
View Related
Dec 29, 2012
I use an Edimax 11n usb wireless lan utility to connect to my router. It gets 60% signal strength and 100% link quality. Either i get disconnected, limited access or no internet access statuses every other hour or not at all. Its intermittent which makes it impossible to explain to the internet provider. The main error that comes up when windows diagnoses is "DNS connection error". Now the internet provider has shown me how to manually set the router to use specific DNS's and that still did nothing.
View 9 Replies
View Related
Jan 13, 2013
I have two AC1200 routers? how do i connect one ac1200 to another ac1200. Only one should act as a DHCP server and broadcast wireless; the other should be simply just a hub (vs. me having to buy a separate hub). What are the correct settings and connections?
View 1 Replies
View Related
Nov 24, 2011
My windows 7 computer was connected to my home's wireless network yesterday perfectly normally. I drove last night to my mother's house and proceeded to connect to her own wifi router wirelessly. Although my sister's computer that's on windows 7 connects ably, and both our iPhones connect, my computer will not. My computer finds the network( it is unsecured without a password if that makes a difference ) connects, receives an ipv4 address in ipconfig, yet does not obtain Internet access. It labels the network as an "unidentified network".
View 2 Replies
View Related
Feb 24, 2013
I am using Cisco WLC 2504 for provisioning Wireless Connectivity over my Wired Environment. Have deployed 4 Access Points spanning my entire campus as per Customer Requirements. Created 10 SSIDs for Different Networks. Would like to know if there is any possibility of Broadcasting say a particular SSID XYZ on only two or 3 Access Points and keep broadcast disabled on Others.
integrating the authentication on these SSIDs using Active Directory Domain Credentials.
View 5 Replies
View Related
May 13, 2013
I have 2 cisco 1242Ag APs in one building and 7 in other building installed in my infrastructure. All these 9 APs are connected to WLC and all of them are added to default ap group to broadcast all the ssid... But 7 in the second bulding are working properly, but the 2 in the other building are not broadcasting the ssids. I checked the configuration in both APs and WLC as well... All the 9 APs are having the same configuration.
View 12 Replies
View Related
Apr 20, 2013
Ive set up a rvs4000 with two vlans, one as a bussiness network and the other as a guest network. Everything works fine and the networks can not see each other. I would like to add wifi and I would like to do so with keeping both networks separate. I have a used 1130AG access point and was wondering if I could use this single AP for both networks. If so, how would I go about doing so? Is there a better suited AP for my needs?
View 4 Replies
View Related
May 16, 2012
I have an RVS4000 running V2.0.2.7 firmware that gives me an "Invalid Character(s) Found" error message when I try to edit an existing ACL.
I'm trying to deploy 57 of these routers and would like to be able to use a pre-built config dropped onto each router.
I initially planned on editing the exported config with a find&replace for my local LAN addresses. Since that didn't work the next reasonable solution would be to edit the ACL list (much more tedious, but still better than hand-entering every ACL on all 57 devices).
when this bug will be addressed? Alternatively, if there is an offline configuration editing tool I would be one happy camper to have it!
View 2 Replies
View Related
Jun 3, 2013
I have an RVS4000, not installed. How can I tell from the unit or the packaging that it is a v1 or a v2, without installing and switching it on (which I don't want to do now) ? Are v1 branded Linsys and v2 Cisco ? Can you tell from the date on the package (mine says copyright 2011) ?
View 1 Replies
View Related
Sep 4, 2011
I don't know if my vendor mislead me, but I need to do this: There is a public subnet in my office, not a 192.168.x.x, but a real Public IP.The reason is that we do VOIP and those are only servers. I installed a RVS 4000 in that location, and assigned a PUBLIC Ip to BOTH the WAN and LAN, since when I connect from outside, using either QickVPN or another identical router, I need to be assigned one of the PUBLIC Ip's on the remote LAN. That is the whole idea of the project, to locate servers remotely and make them use our set of PUBLIC IP's. Well, so far I cannot connect either with the Quick VPN client, or using the VPN Wizard. It goes and creates the tunnel, without error, but when I click test, it fails.
View 2 Replies
View Related
Mar 15, 2012
We have backup and other traffic over our vpn which is affecting our ip phone service between two sites. Our consultant suggested implementing QOS over the VPN to give the phone traffic priority. Is this possible with the rvs4000. Is there any good source saying how to do it. Is the setup of the QOS on this router similar to another router where this has been discussed.
View 1 Replies
View Related
