Cisco Switching/Routing :: 4510 Which Shows System Up-time In Excess Of 56 Years
Feb 17, 2013I've got a Cisco 4510 which shows a system uptime in excess of 56 years. [code]
View 11 Replies
ADVERTISEMENT
Cisco Switching/Routing :: QOS Between 4510 And 3550?
Oct 31, 2011I am having issues working on my QOS between 4510 and 3550 switch connecting on layer 3 through a service provider. I have class maps and policy map setup on both sides and then policy map attached to interfaces however i dont see any traffic matching in policy map on 3550 switch, i do see some traffic matching on 4510 but the speed with which its increasing has my doubts about it. When i make voip calls ( VOIP switches are sitting behind 3550 and are mainly 3550 pwr 24 port switches with phone ports configured for auto qos voip cisco-phone and trusting cos) i rarely see the RTP matching in class under policy map.
View 5 Replies View RelatedCisco Switching/Routing :: IOS Upgrade On 4510
Apr 11, 2013I am currently running 12.2 (53) and am looking to move up to the 15+ train. Are there any pre-reqs prior to the upgrade that any one is aware of?Unfortunately I have no "lab environment" to test it in. I have production switches with minimal impact to the campus and if done late night I could have it restored back before open of business the following morning. My FW is up to the latest version and I have found nothing in the release notes specifically stating that there would require any stepped upgrades up to v15 and higher.
View 6 Replies View RelatedCisco Switching/Routing :: 4510 PoE Switches Keep Failing
Jun 11, 2013We have an issue where switches are failing weekly in a switch closet. In the past month we have gone through several 3750G switches and a couple 4510s. The power supplies have eventually made a popping noise and had to be replaced. on the 4510s we've tried two chassis and gone through several power supplies.The switches have been behind UPS systems so should be receiving conditioned power.Could load from the PoE devices really be causing this? I wouldn't think it's power since they are behind a UPS.
View 5 Replies View RelatedCisco Switching/Routing :: Ports In 4510 Not Working
Jul 10, 2012This has been happening repeatedly time to time! we just replace the part! But now it has come to trouble us again.It happening only in one module like 6 to 10 ports wont work.
we run IOS cat4500e-universalk9.SPA.03.02.00.SG.150-2.SG.bin will there be any bug in it?
Cisco Switching/Routing :: Policing Traffic On 4510?
Nov 21, 2012I have two servers on one subnet that each need to replicate to a single server on another subnet. They also need to replicate to each other. This replication is unidirectional so I will refer to the 2 server subnet as the source subnet and the single server subnet as the destination subnet. In order to keep this replication running without killing the MPLS links on either end, we are trying to use a policy-map that limits bandwidth from the source subnet.The Problem:We have created a policy that polices traffic during specific times of day and limits the bandwidth as prescribed, however, bandwidth is also being limited between the 2 servers on the source subnet which is not needed or desired.Class 512K set dscp ef police 1024000 bps 1024000 byte conform-action transmit exceed-action dropClass Map match-any 512K (id 4) Match access-group name DAGExtended IP access list DAG 10 permit ip host 10.20.0.3 host 10.20.0.10 time-range DAG-REP (active) (22793 matches) 20 permit ip host 10.20.0.4 host 10.20.0.10 time-range DAG-REP (active) (14156 matches)The service policy is applied on the input side of the 2 interfaces on which our devices are connected.As you can see, the access list identifies the interesting traffic as traffic from two specific hosts to one specific host. The problem we are having is that bandwidth is also being throttled between the two source hosts even though it is not defined to do so.What can I do to limit traffic from the two source devices to the single destination device without limiting bandwidth between the two source devices?
View 1 Replies View RelatedCisco Switching/Routing :: 4510 - Setup Ports Between 2 Switches?
Jul 23, 2012We have multiple switches(Cisco 4510, 4507R, 3560's) within our network. I've been looking over the port settings between them and noticed that not all ports that are connected directly from switch to switch are trunked the same. Some are desirable on one switch and forced truck on the other switch.
View 5 Replies View RelatedCisco Switching/Routing :: 10G License For 4510 Switch With SUP7E
Sep 4, 2011I am using Cisco 4510 Switch with Default LAN Base image. Now I have purchased 10G Upgrade license. The part number for Upgrade license is WS-C4500-10G-LIC. I have received a CD from Cisco (named as 'Includes License and Warranty'). Any License upgradation is required for this license? Or this is only a paper License.
I could not find out any .lic file on the CD. Also there is no paper with PAK.
Cisco Switching/Routing :: 4510 No Link On Access Interfaces
May 3, 2012I just upgraded all of our switches on campus to Version 15.0(2)SG4 after about a month of testing. On two switches so far, we are seeing that clients can not connect, and the switch isnt detecting a link. I dont see anything out of the ordinary in int status, port-security, or errors on the interface. Plugging in a different computer does nothing. Only thing that works, is a shut, no shut of the interface. After that, its connected.
View 7 Replies View RelatedCisco Switching/Routing :: 4510 - Upgrading Switch Already Running IOS 15
Apr 4, 2013I have a Catalyst 4510 that is running IOS version 15.X that has a bug and Cisco recommends upgrading the IOS. Are there additional steps required to perform an IOS upgrade due to licencing Cisco put in place?
View 5 Replies View RelatedCisco Switching/Routing :: 4510 Enable MAC Address Filtering
Oct 27, 2010I am planning to enable MAC address filtering (one port on 4510 & another 3560). I want to allow only that MAC address to communicate via that port with the rest of the network and internet.
4510 has PC connected and 3560 had polycom connected. [code]
Cisco Switching/Routing :: 2960 And 4510 IPv6 Support
Mar 2, 2013I have cisco 2960 and Catlyst 4510 switches now we are planning to implement IPV6.
i have the fallowing IOS on my switches.
C2960-lanbasek9-mz.122-50.se5
Cat4500e-entservicesk9-mz.122-54.sg1.bin
The above ios will support for IPV6 or I have to purchase new IOS, which version will support.
Cisco Switching/Routing :: Speed Up Connection Between 6509 And 4510
Feb 21, 2013I got a 6509 version 12.1(22)E2 that I am replacing with a 4510E version 3.40SG with Supervisor Engine 7-E. The 6509 is configured with 20 channel-group for dual fiver connection to ten 3550 switches with trunking enabled with isl encapsulation. The 6509 is the VTP server to each of the 3550 switch clients. There are 40 Microsoft Servers attached ot the Gig RJ45 port modules.
I have attached the 4510 to the 6509 with dual fiber connection configured as a channel group with trunking enabled. I am configuring the 4510 the same as the 6509 except I have to use trunking with dot1q encapsulation because isl is not supported on the 4510. I no longer want to use VTP with the 4510 and have set the it as transparent mode. Each of the 3550 switches are changed from isl trunking encapsulation to dot1q and VTP mode is changed to transparent when they are moved from the 6509 to the 4510.
I want to move the switches over a few at a time and not all at once. The first 4 switches attached with no problems and ran with no problems for the user access to the servers still on the 6509 for a week. Then I found out DHCP was not working for the devices attached to the switches on the 4510. I moved one of our domain controllers form the 6509 to the 4510 to fix the DHVP problem. I have now added 2 more switches with users that use an application on a server still on the 6509 and they are getting disconnect errors after logging into it and using it. Other applications on different server also on the 6509 are having no problems. I moved the switches back to the 6509 to get the users up during business hours. I now plan on moving the server for the application that was failing to the 4510 in hopes that it will fix the problem.
Is there something I can do to speed up the connection between the 6509 and the 4510 so I can continue this transition without having to move the servers to the 4510 as I move the users?
Cisco Switching/Routing :: Convert Configuration From CatOS On 4006 To IOS On 4510?
Sep 26, 2012I need to convert configuration from CatOS on 4006 to IOS on 4510. I am unable to find the conversion tool.
View 5 Replies View RelatedCisco Switching/Routing :: 4510 - Intermittent Packet Drops In Network
Nov 30, 2011We are facing issue related to STP.I am getting MAC FLAP error on Cisco 4510 switch. The effect on network is intermittent Pkt drops in the network. When I checked the specific Ip address I am getting the same with two different. [code] Vlan is created on CORE switch and assign priority 0 than CORE switch should be the Root. but instead Root port is becoming the port where server is connected. Server at last connected to CORE switch via HP switch via other Vlan to CORE switch and creating a loop as shown in Diag. [code] The Priority of Vlan 102 is changed and Root port has been changed due to that. The Bridge ID is the same as CORE switch.
View 7 Replies View RelatedCisco Switching/Routing :: Connecting 4510 TenGig Port To 2960
Mar 10, 2013I am planning on deploying a 2960 switch and will need to uplink it to a 4510 switch. There are 2 TenGig Ports available and I was thinking of uplinking one of them to the 1Gb SFP port on the 2960. Would this work?
View 4 Replies View RelatedCisco Switching/Routing :: 4510 License Installed But EULA Not Accepted
May 1, 2012I just upgrade a license on a cat 4510. The license installed but the EULA was not accepted and it will not upgrade to the new feature set.
View 1 Replies View RelatedCisco Switching/Routing :: 4510 - Command To See If Port Was Ever Up And Passed Traffic
Apr 24, 2012I am looking to find a command or counter to tell me if a cisco switch port on a 4510 was ever up and passed traffic. I want to shutdown all unused switchports on our access switches. But before I do that I need to make sure device is just not off or the person is away on vacation. If I do sh int interface, is there a counter I can reference.
View 4 Replies View RelatedCisco Switching/Routing :: Not Capturing Span Traffic On WS-4510 / SupervisorV / 12.2(54)SG1
Mar 22, 2012I have configured Span port on our 4510. We have an application 5view server to monitor trafic connected to G9/17 Since we have changed the network connection from physical Giga port and add a Port-channel instead, we don't see any more trafic from the new Port-channel to G9/17
We have the configuration below on our 4510 :
monitor session 1 source interface Gi4/6
monitor session 1 source interface Po20
monitor session 1 filter vlan 311 - 312 , 375
monitor session 1 destination interface Gi9/17
From the commands show, we don't see the trafic duplication from the source to the destination port :
Port Source
4510-5567#sh int po20
Port-channel20 is up, line protocol is up (connected)
Hardware is EtherChannel, address is 0016.9de2.a818 (bia 0016.9de2.a818)
[Code].....
Cisco Switching/Routing :: 4510 Power Supply Error - PWR-C45-4200ACV
Mar 17, 2013We are getting below errors on our Cisco 4500 Switche PS after Power Down activity.
Switch1
------------------ show power detail ------------------
Power Fan Inline
Supply Model No Type Status Sensor Status
------ ---------------- --------- ----------- ------- -------
PS1 PWR-C45-4200ACV AC 4200W good good good
PS1-1 off
PS1-2 220V good
PS2 PWR-C45-4200ACV AC 4200W err-disable good good
PS2-1 220V good
PS2-2 220V good
*** Power Supplies of different type have been detected***
00:01:02: %C4K_CHASSIS-3-MIXINPOWERDETECTED: Power supplies in the chassis are of different types (AC/DC) or wattage(code)
Cisco Switching/Routing :: IP Phones Do Not Start After Rebooting (Switch 4510)
Oct 23, 2012I'm having some trouble with a 4510 Switch Line Card. I need some recomendations for troubleshooting it.We have some PoE phones connected to the card number 3. When those phones were restarted, they did not go up again. In order to discard wiring issues, we connected the phone directly to the card 3, and the phone did not go up. If the phone is connected to a different card, it goes up correctly.
Additionally, to restore the service, these phones were migrated to other cards, but when we disconnect the equipment, ports in line card 3 remain in an up / up state (and nothing is connected to those ports!!), and only reflect the actual state after restarting the port.What steps could I do in order to troubleshoot this issue?. What should I look for, or how do I discriminate the problem? Might it be a hardware issue, a PoE issue?
Cisco Switching/Routing :: Maximum Number Of Sessions For Port Mirroring On 4510
Apr 23, 2013Are you only able to have two sessions for port mirroring on a Cisco 4510?
View 1 Replies View RelatedCisco Switching/Routing :: Changing 4510-SUP-6E Redundant Mode To Share-Backplane Mode
Mar 12, 2013I received the following info from Cisco's TAC and wanted to inquire further before I start reconfiguring the switch:
In a redundant Sup-6E setup, the following configuration is supported :
- 1 TenGig uplink on Active Sup and 1 TenGig uplink on Standby Sup
- 1 TenGig uplink on Active Sup and 2 Gig uplinks on Standby Sup
- 2 Gig uplinks on Active Sup and 1 TenGig uplink on Standby Sup
- 2 Gig uplink on Active Sup and 2 Gig uplinks on Standby Sup
If you invoke shared backplane mode, the following configuration can also be supported:
- 2 TenGig uplinks(blocking) on Active Sup and 2 TenGig uplinks on Standby Sup
- 2 TenGig uplink(blocking) on Active Sup and 4 Gig uplinks on Standby Sup
- 4 Gig uplinks on Active Sup and 2 TenGig uplinks(blocking) on Standby Sup
- 4 Gig uplink on Active Sup and 4 Gig uplinks on Standby Sup
Here's the command and information about the "shared-backplane" mode :- [URL]
Currently, we have 2 SUP 6-Es(Module 5 - Active and Module 6 - Stand-by) setup in a redundent mode. I am planning on changing the redundent mode to the shared backplane mode so I can use 2 TenGig converters to uplink 2 access-switches. We purchased 2 TenGig converters and here is how I am planning on using them:
1- One will be used to uplink to two 3750 switches(stacked)
2- One will be used to uplink to a 2960 using a Gig SFP
My questions are:
1- Do I have to install the 2 TenGig converters(4-Gig Uplinks) in the same Module? Or can I use one one in module 5 and the second one in module 6?
2- Will changing the redundant mode to the shared backplane mode require rebooting the switch or disrupt the funtionality of the other linecards?
Cisco Routers :: WAPP4410N Shows Improper Date On Time Page
Sep 11, 2011Time shows as: Current Time: 2011/09/03 Sta 20:53:36 (-08:00) "Sta" day? Also, the timezone is incorrect... I did select GMT -8:00 Pacific Time, and also the "Adjust for Daylight Savings time) So, the above time SHOULD be displayed as 2011/09/03 Sat 20:53:36 (-07:00) If the intention is to show the difference from UTC/GMT. I tried the newer version but it's broken big time. :-( I could not use it at all. None of the configuration changes I made would "stick".
View 2 Replies View RelatedCisco Switching/Routing :: Nx 5548UP After Reboot Log Shows Vpc Down
May 23, 2013We have a Nx5548up pair connected to FI6248 via a vPC. We had to reboot a FI (in order to configure more FC ports) ; following that reboot, we meet many issues.The first log shows the vPC down showing the FI rebbot.2013 May 23 12:31:45 sw-n5kup-fr-eqx-01 %ETH_PORT_CHANNEL-5 PORT_INDIVIDUAL_DOWN: individual port Ethernet1/2 is down
View 1 Replies View RelatedCisco Switching/Routing :: 4500 Ports Shows Only 0 Bit/Seg
May 20, 2012I have installed a WS-X4448-GB-RJ45 on a 4503 chasis. I could not get input or output rate, just shows 0 bit/seg wether or not is forwarding traffic. I would like to know if I have to make any configuration or workaround. The IOS version is 12.2(37)SG1.
View 1 Replies View RelatedSystem And Network Time Do Not Match?
Feb 24, 2011This is happening to me to multiple computers on my domain. When it happens i can only log in as a local user or if I unplug the network cable, log in and then re-connect the networkThe time on all these machines is correct within at least 1 minute but still it's throwing off this error. When reading about this problem I see many fixes that all relate to how to sych the time on the PC.
View 1 Replies View RelatedCisco Switching/Routing :: 3560CG Shows 0 Traffic In Class-map?
Apr 10, 2012I tried to put QoS in a WS-C3560CG-8TC-S version 12.2(55)EX2.It shows 0 traffic in class-map. Here is the config My question is why I can not see the traffic via class-map?it should in the default Q if incorrect mark.I erased the config and config with the autoQoS, shows the same result.
class-map match-any VoIP description Voice IP Phone RTPmatch access-group 157
class-map match-any WEB description Internal Web, SSL Web, DNS query, Pinnaclematch access-group 153
!
policy-map QOSMARK
class VoIP set dscp ef
class WEB set dscp cs3
class class-default set dscp default
[code].....
Cisco Switches :: System Time With New SGE2010Ps And SGE2000Ps
Sep 25, 2012I'm new to the Cisco forums and new to Cisco switches. We just purchased 3 new SGE2010P's and 2 SGE2000P's last week and delivered on Monday.It basically boils down to this. After configuring the system time and hitting Apply and the saving the Running config to the Boot Config and then Restarting the switch the time and date do not remain configured. It other settings but not the date and time.
View 1 Replies View RelatedCisco Switching/Routing :: Catalyst WS-C3750G-48TS-E - Virtual Switching System
Sep 10, 2012I would like to know if Catalyst WS-C3750G-48TS-E recognizes and understand Cisco VSS ( Virtual Switching System) . Is there a List available which tells us which Old Catalyst Switches or current switches understand Cisco VSS?
View 3 Replies View RelatedSystem Clock Does Not Match Local Time?
Jan 16, 2011I'm trying to get an HP laptop running Win7 to see a desktop running WinXP on my network (both wired and wireless) When I run the troubleshooter in Win7, it tells me "system clock does not match local time" as the reason. I have a Belkin wireless router attached to my cable router. I have updated the system clock via the internet on the desktop and checked the time setting in BIOS. These seem to match. I have googled around on this and can't find any accounts similar. My son's Vista laptop and the Win7 laptop have seen each other since day one. The laptop and desktop did see each other at one time, but the connection was lost after I went to a hotel and changed public network settings temporarily. I can ping the desktop from the laptop, but it times out when pinging the laptop from the desktop. I'm running an avast firewall on both, but can't see a problem there.
View 6 Replies View RelatedD-Link DIR-655 :: System Time Becomes An Hour Off After 7 Days
Oct 30, 2011I have the DIR-655 rev B1 with 2.03NA firmware. After 7 days the system time falls back an hour. The timezone settings are correct and I have used both 0.us.pool.ntp.org and DLink's time servers.
View 6 Replies View RelatedCisco Switching/Routing :: Cat 2960 Shows Mac Address Port As Dropped?
Jul 30, 2012I am configuring a Cat 2960 port for connecting a VOIP phone, authenticated by MAB. On connecting the phone, I get the port authenticated and assigned to the correct VLAN, with LLDP-MED advertising the correct voice vlan. However, I then see no traffic from the phone on the switch. I can see the MAC address of the phone is learned in the right VLANs, but the mac address is showing as "Drop", which normally means the address is statically configured to be blocked. There is no static mac address table blocking configured on the switch.
Switch Version
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 50 WS-C2960-48TC-L 15.0(1)SE3 C2960-LANBASEK9-M
Port configuration
interface FastEthernet0/1
description "Standard user port"
[code].....