I have the DIR-655 rev B1 with 2.03NA firmware. After 7 days the system time falls back an hour. The timezone settings are correct and I have used both 0.us.pool.ntp.org and DLink's time servers.
View 6 RepliesI have copied my computer's time in the router time setup under Time in the "tools" section of the router setup. After a few days of the router being up without a hard restart, it has lost 10 minutes somehow. I went to the logs and cleared them out and then looked at the entry showing that the log was cleared and looked at my computer clock and the time stamp of the log entry, and it was 10 minutes slower than my computer clock that I had originally set it from. I have a clock plugged in by the computer, and my computer always matches the clock that it plugged in, so I know it isn't my computer loosing time. What is going on here? Why does the router loose the correct time after it has been up and not unplugged or rebooted at all? I know that the router will loose the time if you unplug it, but this isn't the case here.
View 5 Replies View Relatedrecently i bought a x1000 for my home network. I use the x1000 as router an wireless accessPoint between my WAN internet uplink an my home network...yesterday the router hang up completely. internet stoppp working. so i tried to access to x1000 to check if PPPoE connection was still active. But it did not load the webinterface. I tried to connect over WLAN and LAN. Both not working!
View 7 Replies View RelatedRegion : Others
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : 3.11.3 Build 100408
ISP : Telekom
the SYS light, keeps blinking is that normal?
I've noticed this in the last few days, but my internet seems to crash at the exact same time (29 past the hour) every hour. We've recently had a new modem in, and was working fine. I recently had a mass clearout of a lot of things in my PC (got rid of 500 gigs), so I'm wondering whether I may have deleted something which has caused this.
View 4 Replies View RelatedOne of my 7921 phones disconnect ten time an hour and during conversations. Sometimes, people who call on this phone are redirected to the answer message.This phone is connected through WIFI network and Cisco Callmanager 4.2 manage all phones (we have about 80 phones on the network). I thought it was a problem with the phone but I exchange with another one and it's exactely the same problem. The problem is just for a line in particular. All the 7921g phones in my company are configured from mac address in the call manager. This problem occured after a storm but I'm not really sure that it's related to.
View 2 Replies View RelatedTL-WR1043ND disconnects every two days
View 7 Replies View RelatedRegion : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 121210 Rel.73912n (Beta)
ISP :
I have tried to go through the tech support email but no dice. My router disconnects every two days. The sys light will stay solid and require a reboot and my computer connected to the router will be unaffected . I have a 30mb connection with only 2-3 wireless clients on at the same time as the wired. The response I got from tech support email after waiting almost a week without a response was :
Because there's not much we can do to fix the problem right now and TL-WR1042ND is more competent for your network, I suggest you to change for it.
If you still don't wanna change for TL-WR1042ND, change for a new TL-WR1043ND to have a try."
This is answer I get after already asking once why they want me to downgrade for a different router . What exactly the TL-WR1042ND is going to do for me that the one I have won't,but I cannot get a answer.I have no idea what they mean by "competent ", I don't believe my network is anything special and see no reason why the problem would be fixed by downgrading . This is the second router since December I have had and really dont feel like paying another 15$ shipping back to newegg for a refund.
I have a wireless schedule setup on my DIR-655. Works great. Now I would like to run different hours on different days. Have wireless up on certain hours during the week, different hours on weekends.
How do I set up a schedule to one one set of hours during the week, and a different set of hours during the weekend?
My Dir-655 sometimes seems to forget it is now DST. Just now the routers time was 8:07 but the real clock time was 9:07. This is the 3rd time this has happened and when it does it messes up access controls. If it can't keep the right time the access controls for me are useless. Clicking save settings gets the time set back to what it should be. How can I stop this nonsense.
View 11 Replies View RelatedRegion : UnitedKingdom
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : TL-WR1043ND_V1_120405
ISP : BT Infinity (1)
I have a TL-WR1043ND v1 with the latest firmware installed TL-WR1043ND_V1_120405.I loose access to the router (can't see web page, can't config, can't restart).I have a Linux server on the Ethernet, and uplink through 200Mbps powerline adapter to the BT Infinity modem. A few other devices on the wireless.The router works well and I prefer it to the BT Home Hub 3 for fiber because it proved to be faster in many cases as tested.But after a few days the web interface becomes inaccessible. It's like the web server died or something. Browser says connection reset, if I try telnet to port 80 says connection refused.Actually I just did a full netcat scan (sudo netcat -z -v -192.168.1.1 1-65535) and all ports say connection refused.Ping works - I can ping it allright.DHCP server works too, just restarted a computer and got IP from the router.Port forwarding works as well and DynDNS seems to work as well as my ISP changes the IP periodically and I can always find the updated one.All works - exept I can't access the router in any way!If I restart (remove power and plug it back in), it boots and I can access the router again.So restarting won't work remotely, I actually have to go home to re-plug it!
My DSC-930L's web interface becomes unresponsive about an hour or two after power cycling my camera. It still responds to pings, and it still sends images to FTP when it detects motion, but I can't log into it via web interface, mydlink, or the iphone app. Power cycling the camera fixes the problem for an hour or so but then its right back to not working again.
View 8 Replies View RelatedThis is happening to me to multiple computers on my domain. When it happens i can only log in as a local user or if I unplug the network cable, log in and then re-connect the networkThe time on all these machines is correct within at least 1 minute but still it's throwing off this error. When reading about this problem I see many fixes that all relate to how to sych the time on the PC.
View 1 Replies View RelatedRegion : India
Model : TL-MR3020
Hardware Version : V1
Firmware Version : 3.14.2 Build 120817 Rel.55520n
ISP : BSNL India
I bought this device yesterday, I am using this device with BSNL's EVDO (cdma network).It detects my modem fine, and it connects fine, and I can browse.Exactly at 50th min(few seconds difference), my net gets disconnected.I have tried all modes, connect manually, automatically, on demand -- nothing solves the concern.Changed idle timeout to 0.The device when connected directly works fine for more than 12 hours.Updated firmware to the latest 3.14.2 Build 120817 Rel.55520n.Tried Resetting the Router to factory defaults and configured again.Tried all troubleshooting steps from FAQ as in change it to WEP security, connect manually, idle timeout setting.Most importantly, tried creating a BIN file using USB sniffer and used it, even then its the same issue.
I'm trying to get an HP laptop running Win7 to see a desktop running WinXP on my network (both wired and wireless) When I run the troubleshooter in Win7, it tells me "system clock does not match local time" as the reason. I have a Belkin wireless router attached to my cable router. I have updated the system clock via the internet on the desktop and checked the time setting in BIOS. These seem to match. I have googled around on this and can't find any accounts similar. My son's Vista laptop and the Win7 laptop have seen each other since day one. The laptop and desktop did see each other at one time, but the connection was lost after I went to a hotel and changed public network settings temporarily. I can ping the desktop from the laptop, but it times out when pinging the laptop from the desktop. I'm running an avast firewall on both, but can't see a problem there.
View 6 Replies View RelatedIs it possible to detect a system time change on a workstation on a network? There is suspicions that there is someone trying to use their system time as an excuse to go to lunch early at work, "but my computer says its 1 O'Clock" When everyone else's computer displays 12:48.......
View 1 Replies View RelatedI'm new to the Cisco forums and new to Cisco switches. We just purchased 3 new SGE2010P's and 2 SGE2000P's last week and delivered on Monday.It basically boils down to this. After configuring the system time and hitting Apply and the saving the Running config to the Boot Config and then Restarting the switch the time and date do not remain configured. It other settings but not the date and time.
View 1 Replies View RelatedI have a WAG160Nv2 with Firmware Version:V2.00.20 Two problems
1. Slow wireless speed - only 2Mbit - with cabte up to the lines max 15Mbit
2. The routers system time is wrong - it says " 03-01-2000 02:19:54" I have set the correct system time but no difference
I have tried a lot of wireless options and some of the timezones but i did not solve the problem
I've got a Cisco 4510 which shows a system uptime in excess of 56 years. [code]
View 11 Replies View RelatedAI have a Dir-825 router. The 5GHz is turned off and the wirless is on G/N. I have shawcable for my isp and my firmware is 2.06 and its a Rev B Router. I also have Qos Engine on for allowing me to have 2 xboxes on Open NAT.problem is my wireless signal for some wired reason is VERY weak. A while ago it used to work really far way outside. It was around 150ft distance at 4 bars. Now for some reason I can't even go upstairs without getting a 1 or 2 bar signal.
View 3 Replies View Relatedi have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
Hardware Version: A4 - Firmware Version: 1.32EU
I got 3 new TP-Link WA901ND PoE access points for a wireless network I manage. Right now I'm using the stock injectors that came with them because I need to get adapters still so I can use them with my PoE switch.
Hardware Version: v2
Firmware Build: 3.12.16 Build 120224 Rel.61005n
Wireless Mode: Access point
Channel: Auto
Mode: 11bgn mixed
Channel Width: 20/40MHz
Max TX: 300MBPs
About a week after getting these units installed and having them work great, I started running into problems. One of the unit's system light was not on, and I could not connect to the access point from my phone, or log into the web interface. I did a soft reboot (unplug for 30 seconds, plug back in) and it seemed to work fine, but then I had the same problem, and soon both units were doing it. I thought i might be pushing the distance limit the stock injectors have, but then I started having the same problem with a unit that is 10 feet from the injector.
I have an older D-Link DGL-4300 wireless router, I've purchased a wireless home security system and can't seem to get the 2 connected. I've tried resetting the router & modem (powering down & waiting from 1-5 minutes), and my router just won't read the port that I've plugged the security system ethernet cable into.I think the problem is my firewall but I don't know how to set it to allow the router to read the port that I've plugged into, or it could be the firewall that my anti-wirus has or possibly both.My equipment is Comcast cable, router (as noted above) and a D-Link DCM-202 modem, Windows XP 3, and Norton anti-virus. Now I also have my phone through Comcast and it has it's own modem.
View 7 Replies View RelatedI accidentally created a home network and want to remove it, as it blocks all my wireless devices.
I have a dir655 with 2.o firmware
Os on computer I set it up on is win 7 64 bit
How to make other wireless devices easily recognize it? when I try to access it the wireless computers ask me for code that I entered on setup that was printed on bottom of router but system doesn't recognize it.
Region : Philippines
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I am having troubles configuring TL-WR740N. After I connect everything and turned in on, the system Light is ON and the power light is also ON and nothing else. I Connected my laptop to the 1 of 4 LAN ports and the WAN to my modem.
In my log I have the message: "Access denied to wireless system with MAC address 0020008E971E". When I checked the vendor for this MAC, it shows Lexmark international inc, which fact make me feel something is wrong. My first thought was that somebody trying to break into my net but I am close to accept that the owner of Lexmark WiFi printer without an idea in networking, just tried to connect it to his network and after failing to do that, it's wired and wireless features are still on. But still could this be bug or something? I am posting some logs when I first discovered the problem and after I granted access to the device with the MAC address 0020008E971E. I forgot to tell you, that before I decided to post here I did firmware upgrade from Hardware version A3 1.10 to 1.35NA (I bought it from US) with factory default restore. The result was absolutely the same - the messages kept coming "Access denied to wireless system with MAC address 0020008E971E". So I granted access to that MAC and checked the logs again. There is a line in the log that stated "primary:"
View 7 Replies View Relatedmy PC and laptop are both suddenly running sluggish since yesterday morning. pages take forever to load; slow to start videos, etc. i called ATT this morning...the auto test said i needed to talk to someone because there was a problem noted. but the live rep ran tests and said the speeds were within the norm for my service. i asked her why the auto test reported an issue, and she checked, only to come back to say "it's a problem with the modem." oh, and a new one from them is $80-100+
[code]...
I have the revision b version of the dir-655. I'm having a couple issues which im not sure if are related to the dir-655 or something else.
I used to be able to do this, then all of the sudden (I may have changed something) I cannot anymore. The issue is: If I try and access my linux server using http://[My Public IP Address]/ from *inside* my LAN, It will time out and not connect. If I try and access my same public ip address from *outside* my LAN, it works fine.
My router was noticeably slow to respond when navigating the menu system. Then, I changed the ip address to 192.168.0.2 (previously it was 192.168.0.1) and all of the sudden its fast again. I tried rebooting and power cycling before I changed the IP and it was always slow using 192.168.0.1.
I'm experiencing some problems with a new X1000 gateway. The device works very well for 2-3 days. After that period, it seems to just freeze. I can connect to the wireless, but no IP address is leased. Wired clients keep their IP address, but can't connect to the internet. Communication between the wired clients is still possible (Ping, CIFS, LAN games,...). The DSL sync LED is lit as is the Internet LED. The management interface does not load. Doesn't matter is there has been a lot of internet traffic or virtually none. The only way to make it work again, is to cycle the power.
I've been fiddling with the different features from all off to all on, but the problem persists. I even got a replacement device, but that has the exact same problems. My ISP tells me that the Cisco and Linksys devices are fit to work on their network. I'm using a Zyxel gateway at the moment, which is absolutely fantastic, but has no wireless and useless QoS management.
Running ACS5.2, Windows XP Pro, Window Server 2003 and Cisco Anyconnect Client. When the machine name password changes between the PC and the AD server the ACS will error out with "24485 Machine authentication against Active Directory has failed because of wrong password".TAC has been working with us on this and sees the error in the logs but does not have an answer on with to do to solve this. It has the same problem with Wireless Zero. Once the PC is rebooted the error goes away for 30 days. We are in a hospital setting so this is a not just a minor problem
View 16 Replies View RelatedI'm having this weird problem with an IP phone behind a WGB. The setup is like this: Cisco controller -> Switch -> switch -> AP (Air LAP1142) -> WGB (Air LAP 1262) -> switch -> IP phone.
The phone works, sometimes. Sometime for days, sometime for hours, then it disconnects and what I have to do then to get it working again is to run this command on the bridge. "no workgroup-bridge unified-vlan-client", then wait for it to disassociate, then run "workgroup-bridge unified-vlan-client" and after that it gets a stable connection (for a undetermined amount of time).
Here´s the WGB config:
version 15.2
no service pad
service timestamps debug datetime msec
[Code]....
I am running a 1921 with 15.0(1)M4 on it. The router has a /29 public block assigned to it so I have a public IP for my router's GW, a public IP for the WAN interface on the router, a public IP for PAT and the three remaining public IPs I use them as static NATs for internal hosts.
My problem is that the particular static NAT assigned to static host1 seems to "hang" every few days. You can ping the public IP and it will respond but the rest of the services of the host like www, ftp and telnet do not respond. If I reboot the router then all services of host1 will work again. Note that all other static IPs including the ones used for static host2, host3 and PAT will always work and never give any problems.
I am fairly certain that this is not a config problem so I have shuffled around the public-to-private NAT entries. Basically whatever public IP I assign to this host1 will at some point hang. The host2, host3 and PAT always work and never hang no matter what public IP I issue to them.
So since it isn't a problem with the public IP I changed the private IP of host1 and still it hung!! This host1 happens to be a linux box. host2 and host3 are a Windows server and a different flavor linux if that make some kind of difference.
my router internal time somehow will not working on manual config it will stop after certain period now im trying to use NTP
[code]....