Linksys Cable / DSL :: X1000 Freezes Every 2-3 Days
Mar 26, 2013
I'm experiencing some problems with a new X1000 gateway. The device works very well for 2-3 days. After that period, it seems to just freeze. I can connect to the wireless, but no IP address is leased. Wired clients keep their IP address, but can't connect to the internet. Communication between the wired clients is still possible (Ping, CIFS, LAN games,...). The DSL sync LED is lit as is the Internet LED. The management interface does not load. Doesn't matter is there has been a lot of internet traffic or virtually none. The only way to make it work again, is to cycle the power.
I've been fiddling with the different features from all off to all on, but the problem persists. I even got a replacement device, but that has the exact same problems. My ISP tells me that the Cisco and Linksys devices are fit to work on their network. I'm using a Zyxel gateway at the moment, which is absolutely fantastic, but has no wireless and useless QoS management.
recently i bought a x1000 for my home network. I use the x1000 as router an wireless accessPoint between my WAN internet uplink an my home network...yesterday the router hang up completely. internet stoppp working. so i tried to access to x1000 to check if PPPoE connection was still active. But it did not load the webinterface. I tried to connect over WLAN and LAN. Both not working!
I have just bought an X1000 box, it seems to be randomly locking up and the only way around the issue is to reboot. I have also noticed it can't seem to handle streaming video either.
My ADSL has been checked and all is OK and if I don't stream video generally things seem OK for a couple of days. If I run a continual ping to the unit you can see that now and again the request times out but then some times comes back and other times I need to reboot again. The log file seems to show very little either.
I recently bought an x1000 modem/router and found that after 2/3 days of staing active and properly functioning, it does not allow me to login to wifi connection with none of my devices (tried iPhone, iPad and 2 windows pc).Firmware version is v1.0.00 build 018 Sep 04, 2012
Everytime i connect my phone on my network the entire network freezes: the lights on the router stills on but there is no connection on the network. There is anything that i can do to prevent it?
I've got a wireless adapter for my desktop and thats what i've been using for years to connect, but now i'm am trying to get a more reliable connection by having the ethernet cable plugged in. Problem is, as soon as I plug it in the whole computer gets extreamly sluggish or sometimes freezes up completely. If I am very patient, I can very slowly do something things. If I open the browser, it probably takes a minute for it to load. Opening the control panel, the window pops-up but none of the icons will appear until it times out. And trying to use the network icons on the taskbar to get into network settings is impossible. Weird thing is as soon as I unplug it and turn the wifi back on, the PC starts responding super quick again within seconds.
Compaq Evo W4000 with XP professional.Comp works fine when no ethernet cable plugged in - after 10 secs of plugging it in - it freezes Have run malware bytes and combofix already - no change.Disabled everything in startup menu and non Microsoft services Works OK in SAFE MODE with networking though
I have an E1200 wireless router. I need to restart it every 1 to 2 days. After restarting it is good until the next time. This has happened with different routers and upgraded firmware to the newest version available on all.
I just bought an EA-4500 and i am having problems with rebooting the device. Every time I change a setting and the router reboots it never starts up again - and the logo LED doesn't flash, it is on constant. I have to cut the power and wait for about 15 minutes, and then it boots up fine - logo flashing and all.
Every time i plug in my adapter wusb600n and i got internet i go play black ops 2 my game and my whole pc freezes and if i do an other internet without the adapter and use a sitecom adapter or an linksys pci card everything works good but with the wusb600n i every time get freezes even when im not in game, my pc freezes every time and it is really good internet speed with this dual band adapter?
My e4200v2 which I have been using for about 4 months locks up or freezes regularly - as often as once or twice a week. That is to say the wired laptop can't reach the router and the smart phone does not have a signal. This often happens when there is no phone or computer running. My current firmware is 2.0.37 and it just happened again. The logging capability is absolutely terrible so you can't tell why or when it went down, and what happened just before it went down. I pull the plug on power and when it comes back the log is clean. avoid the freezing/lockup or for logging incoming and outgoing with timestamps?
Since I've bought a new Cisco router last summer,, a Linksys E1200 (v.1 updated...) (always in the wireless mode), my laptop (Sony, Vaio VGN-NW110D) freezes when I stream videos online or when I use skype video calls. It sometimes freezes for a few minutes (in that case it's just really extremely slow and it sounds like a satanic robot), and then comes back (but does it again a few minutes later. Or sometimes, and this is more frequent with skype video calls, it completely freezes, and I have to reboot the hard way...This never happened to me before and I've been watching videos and video skyping for years. I have windows 7, service pack 1 (32 bits) now . I have windows 7 now, since about the same time I bought the router. But what makes me think its related to the router is that when I'm at work, or at my parents, or sisters, or boyfriend's house, this problem does NOT occure.... I don't know if this information could be relevant, but this does not happen when I make videos calls with skype on my iphone.
My e4200 freezes and not connect in any interface not Ethernet not wireless, i connect reset in any way ( push the reset button, push the reset button an unplug the power.
I was using the Sony Tablet with an earlier version of a linksys modem and everything worked fine. Since changing to the 4500 I have access to the network have full internet service and the anywhere from about 5 to 10 minutes later the internet freezes on the table and I have to reboot connection and the its fine for about another 5 to 10 minutes before it freezes again.
After installing a WMMP600N on an HP Pro 3410 (BIOS 7.04) the computer "freezes" after booting or doesn't boot at all. On the other hand, installing the same board on an HP (Compaq) DX2390 (BIOS 5.3) doesn't cause any problem: both the machine and the board work nicely together. Both machines run on Windows 7 Ultimate, with the latest driver from Linksys.
my PC and laptop are both suddenly running sluggish since yesterday morning. pages take forever to load; slow to start videos, etc. i called ATT this morning...the auto test said i needed to talk to someone because there was a problem noted. but the live rep ran tests and said the speeds were within the norm for my service. i asked her why the auto test reported an issue, and she checked, only to come back to say "it's a problem with the modem." oh, and a new one from them is $80-100+
I have copied my computer's time in the router time setup under Time in the "tools" section of the router setup. After a few days of the router being up without a hard restart, it has lost 10 minutes somehow. I went to the logs and cleared them out and then looked at the entry showing that the log was cleared and looked at my computer clock and the time stamp of the log entry, and it was 10 minutes slower than my computer clock that I had originally set it from. I have a clock plugged in by the computer, and my computer always matches the clock that it plugged in, so I know it isn't my computer loosing time. What is going on here? Why does the router loose the correct time after it has been up and not unplugged or rebooted at all? I know that the router will loose the time if you unplug it, but this isn't the case here.
I have the DIR-655 rev B1 with 2.03NA firmware. After 7 days the system time falls back an hour. The timezone settings are correct and I have used both 0.us.pool.ntp.org and DLink's time servers.
Running ACS5.2, Windows XP Pro, Window Server 2003 and Cisco Anyconnect Client. When the machine name password changes between the PC and the AD server the ACS will error out with "24485 Machine authentication against Active Directory has failed because of wrong password".TAC has been working with us on this and sees the error in the logs but does not have an answer on with to do to solve this. It has the same problem with Wireless Zero. Once the PC is rebooted the error goes away for 30 days. We are in a hospital setting so this is a not just a minor problem
I'm having this weird problem with an IP phone behind a WGB. The setup is like this: Cisco controller -> Switch -> switch -> AP (Air LAP1142) -> WGB (Air LAP 1262) -> switch -> IP phone.
The phone works, sometimes. Sometime for days, sometime for hours, then it disconnects and what I have to do then to get it working again is to run this command on the bridge. "no workgroup-bridge unified-vlan-client", then wait for it to disassociate, then run "workgroup-bridge unified-vlan-client" and after that it gets a stable connection (for a undetermined amount of time).
Here´s the WGB config: version 15.2 no service pad service timestamps debug datetime msec [Code]....
I am running a 1921 with 15.0(1)M4 on it. The router has a /29 public block assigned to it so I have a public IP for my router's GW, a public IP for the WAN interface on the router, a public IP for PAT and the three remaining public IPs I use them as static NATs for internal hosts.
My problem is that the particular static NAT assigned to static host1 seems to "hang" every few days. You can ping the public IP and it will respond but the rest of the services of the host like www, ftp and telnet do not respond. If I reboot the router then all services of host1 will work again. Note that all other static IPs including the ones used for static host2, host3 and PAT will always work and never give any problems.
I am fairly certain that this is not a config problem so I have shuffled around the public-to-private NAT entries. Basically whatever public IP I assign to this host1 will at some point hang. The host2, host3 and PAT always work and never hang no matter what public IP I issue to them.
So since it isn't a problem with the public IP I changed the private IP of host1 and still it hung!! This host1 happens to be a linux box. host2 and host3 are a Windows server and a different flavor linux if that make some kind of difference.
Region : UnitedStates Model : TL-WR1043ND Hardware Version : V1 Firmware Version : 3.13.12 Build 121210 Rel.73912n (Beta) ISP :
I have tried to go through the tech support email but no dice. My router disconnects every two days. The sys light will stay solid and require a reboot and my computer connected to the router will be unaffected . I have a 30mb connection with only 2-3 wireless clients on at the same time as the wired. The response I got from tech support email after waiting almost a week without a response was :
Because there's not much we can do to fix the problem right now and TL-WR1042ND is more competent for your network, I suggest you to change for it.
If you still don't wanna change for TL-WR1042ND, change for a new TL-WR1043ND to have a try."
This is answer I get after already asking once why they want me to downgrade for a different router . What exactly the TL-WR1042ND is going to do for me that the one I have won't,but I cannot get a answer.I have no idea what they mean by "competent ", I don't believe my network is anything special and see no reason why the problem would be fixed by downgrading . This is the second router since December I have had and really dont feel like paying another 15$ shipping back to newegg for a refund.
I have a wireless schedule setup on my DIR-655. Works great. Now I would like to run different hours on different days. Have wireless up on certain hours during the week, different hours on weekends.
How do I set up a schedule to one one set of hours during the week, and a different set of hours during the weekend?
I am running big wireless network, with 20no of 5500 with 7.0.116.0 version. I have more than 20,000 AP's. All LWAPP which are up for more than 200-300 days has to be rebooted, this problem is with all AP's. clients are not getting connected,after reboot they work fine.how do the same from ncs.
We have 4 WAP121s running 1.0.1.10. After a couple of days of operation, they all become unusably slow. The admin web interface takes several minutes to load, and wireless clients timeout before RADIUS authentication can complete. Waiting long enough allows the diag info to be downloaded, which shows hostapd using all of the CPU time available: [code]
As a workaround, we used to use a small script to reboot them every night via SSH, but someone at Cisco made a less-than-brilliant decision to remove this advertised feature.
I have the problem that our ciscoworks server gets out of memory after few days. The memory utilization is always getting higher an higher (above 95%). Sometimes it is only after 3 days and sometimes it is after 1 week. So it happens not regularly. I have made an screenshot from the services which use a lot of memory. And at this time the memory utilization is getting higher and higher again....I think there is a problem with tomcat or dbsrv10.exe, there are also a lot of cwjava.exe running.
My set up is a 2wire router that connects to the internet, with an ethernet power plug connected to it. Over the other side of the house, I have the other ethernet power plug connected, with a Netgear router in access point mode.The main router is on 192.168.1.1, and the access point is on 192.168.1.3. The DCHP server is enabled on the main router with range 192.168.64 to 192.168.1.253. The access point has the DCHP server turned off. The routers have the same APN and security (WPA2-PSK).Also, the wireless channels don't overlap, channel 1 and 11.Now to my problem:The internet always works fine for a few days when the routers are turned on. But at some point between 1 to 3 days later, every computer can't obtain an IP address while connected to the access point. But all computers can connect to the main router (i.e. when closer to the main router than the access point), and then go near the access point and it keeps the connection. If I reboot the access point, then everything works again for a few days.
Region : UnitedKingdom Model : TL-WR1043ND Hardware Version : v1 Firmware Version : TL-WR1043ND_V1_120405 ISP : BT Infinity (1)
I have a TL-WR1043ND v1 with the latest firmware installed TL-WR1043ND_V1_120405.I loose access to the router (can't see web page, can't config, can't restart).I have a Linux server on the Ethernet, and uplink through 200Mbps powerline adapter to the BT Infinity modem. A few other devices on the wireless.The router works well and I prefer it to the BT Home Hub 3 for fiber because it proved to be faster in many cases as tested.But after a few days the web interface becomes inaccessible. It's like the web server died or something. Browser says connection reset, if I try telnet to port 80 says connection refused.Actually I just did a full netcat scan (sudo netcat -z -v -192.168.1.1 1-65535) and all ports say connection refused.Ping works - I can ping it allright.DHCP server works too, just restarted a computer and got IP from the router.Port forwarding works as well and DynDNS seems to work as well as my ISP changes the IP periodically and I can always find the updated one.All works - exept I can't access the router in any way!If I restart (remove power and plug it back in), it boots and I can access the router again.So restarting won't work remotely, I actually have to go home to re-plug it!
A few weeks ago, I noticed that my Internet connection had slowed down to a crawl. I waited a few days hoping it would go away on its own, but it didn't get better. So I asked this question about how to make it faster.
The problem went away after I updated to the latest firmware, so I didn't follow up too carefully. But every few days since then, my Internet has slowed down again. Unlike before, all I have to do to fix it is open the router administration page and press the "Reboot" button. Nothing else seems to work, though I'm sure there are options I haven't tried.
If it makes a difference, my girlfriend and I both transfer large amounts of data fairly routinely for school (videoconferencing, downloading entire recorded lectures).
The router is a Cisco/Linksys WRT160N v3 that's about a year old. Most of the time, it deals with just two standard Windows 7 laptops.
What could be causing these slowdowns, and how can I get rid of them?
I installed dd-wrt on my router, and I seem to be getting higher and more consistent speeds. Perhaps more importantly, my memory use is fairly constant.
My RV110W is only a few months old and apparently started ginvg me issues shortly after I got it. Since it was new, however, I only recently suspected it as the culprit!
I have a simple home/small business setup. A single PC wired into the lan and a handful of occasional use laptops & Android phones/tablets and a Playstation.My connection is a 30M down / 5M up cable link. I have a UBEE DOCSYS 3.0 cable modem operating in passthru mode to my RV110W.
Over the course of several days, thruput drops from the measured 30/5 down to as low as 1/whatever. Rebooting the RV110W restored full speed. The UBEE has never been rebooted during this time. Connecting my wired desktop PC directly to the UBEE modem give me the full 30 downlink speed even when the RV110W perfomance has dropped to 5 or even 1.
I am using onle a single wireless LAN, no logging turned on, no VPN, no other 'tuning of settings.As it is, this device must be rebooted every few days to restore full network speed. This is unacceptable, of course - especially from a small business class device!
