recently i bought a x1000 for my home network. I use the x1000 as router an wireless accessPoint between my WAN internet uplink an my home network...yesterday the router hang up completely. internet stoppp working. so i tried to access to x1000 to check if PPPoE connection was still active. But it did not load the webinterface. I tried to connect over WLAN and LAN. Both not working!
View 7 Replies
I'm experiencing some problems with a new X1000 gateway. The device works very well for 2-3 days. After that period, it seems to just freeze. I can connect to the wireless, but no IP address is leased. Wired clients keep their IP address, but can't connect to the internet. Communication between the wired clients is still possible (Ping, CIFS, LAN games,...). The DSL sync LED is lit as is the Internet LED. The management interface does not load. Doesn't matter is there has been a lot of internet traffic or virtually none. The only way to make it work again, is to cycle the power.
I've been fiddling with the different features from all off to all on, but the problem persists. I even got a replacement device, but that has the exact same problems. My ISP tells me that the Cisco and Linksys devices are fit to work on their network. I'm using a Zyxel gateway at the moment, which is absolutely fantastic, but has no wireless and useless QoS management.
I am running a 1921 with 15.0(1)M4 on it. The router has a /29 public block assigned to it so I have a public IP for my router's GW, a public IP for the WAN interface on the router, a public IP for PAT and the three remaining public IPs I use them as static NATs for internal hosts.
My problem is that the particular static NAT assigned to static host1 seems to "hang" every few days. You can ping the public IP and it will respond but the rest of the services of the host like www, ftp and telnet do not respond. If I reboot the router then all services of host1 will work again. Note that all other static IPs including the ones used for static host2, host3 and PAT will always work and never give any problems.
I am fairly certain that this is not a config problem so I have shuffled around the public-to-private NAT entries. Basically whatever public IP I assign to this host1 will at some point hang. The host2, host3 and PAT always work and never hang no matter what public IP I issue to them.
So since it isn't a problem with the public IP I changed the private IP of host1 and still it hung!! This host1 happens to be a linux box. host2 and host3 are a Windows server and a different flavor linux if that make some kind of difference.
I have a WRT160N that I used just once after purchase (my ISP gave me a wireless router). I could not remember the PW, so I reset. (The computer saw the old router name but I had no PW)When I run the software (CD that came with the product says 150N), it get to "configuring computer" and stops there.I tried downloading the software, but when I try to run it says "Application requested runtime to terminate in an usual way."When I go to the 192. URl and try to login using a bank user name and 'admin," it jsut keep bringing up the password box.
View 2 Replies View RelatedI have the DIR-655 rev B1 with 2.03NA firmware. After 7 days the system time falls back an hour. The timezone settings are correct and I have used both 0.us.pool.ntp.org and DLink's time servers.
View 6 Replies View RelatedI have just bought an X1000 box, it seems to be randomly locking up and the only way around the issue is to reboot. I have also noticed it can't seem to handle streaming video either.
My ADSL has been checked and all is OK and if I don't stream video generally things seem OK for a couple of days. If I run a continual ping to the unit you can see that now and again the request times out but then some times comes back and other times I need to reboot again. The log file seems to show very little either.
I have an E1200 wireless router. I need to restart it every 1 to 2 days. After restarting it is good until the next time. This has happened with different routers and upgraded firmware to the newest version available on all.
View 1 Replies View RelatedTwo years ago, a lightning strike fried my ADSL router and LAN port on the motherboard (ASUS A7V8X-X) of my now very old system. After that, I bought a Wi-Fi USB adapter (AirLive WL1600-USB) and disabled the fried LAN port. Since that moment, my computer kept freezing totally randomly for the past two years - it didn't matter whether I run a dozen of programs or simply leave the system alone. First I didn't know what's causing those freezes, until a week ago. You see, we were forced to cancel our ADSL account for four months, so I haven't used that Wi-Fi adapter for the entire summer (I disconnected it and uninstalled its drivers). During that time - not a single freeze for four months, no matter how great the system load or temperature. A couple of weeks ago, we activated our ADSL account again, so I plugged the Wi-Fi adapter in and installed its drivers - and the freezes started again.
View 3 Replies View RelatedWhen I try to boot my ASA5550 it hangs at "booting system please wait". I have tried to reseting the ASA but this doesn't work. what to try as I cannot get to the rommon.
View 9 Replies View RelatedI've a Cisco 5550 which hangs on powering up and stays at " Booting System, please wait..." forever and it has a flashing green Status LED.
The steps I've taken so far are:
1. Consoled with a different computer and tried to send the break signals (didn't work)
2. Open up the unit tried to remove the RAM's and reseated them again.
3. Taken out the CMOS battery on the board and replaced it with the new one (no luck still)
What is the next step, or shall I assume that the unit is dead.
my router stop every exact 3 days, why? when it stop , i don't have net connections and i can't send ping in it?
i try to update de firmware and it do same if i remove de power cable and put it back it start ok?
how i can resolve that?
Have been trying for the past two days to install a new E4200. It gets to 25% in the setup and then errors out and says I need to contact customer service.
Connecting through a brand new DSL modem that I know works as I can get access through my old router.
My PC (Windows 7) is directly connected to the router. I got to the point where I named the router in the install process the first time, but then it hung.
Have tried to use the CD to re-setup with no success. I've tried the hard reset holding in the button for 10 seconds and unplugging but nothing has changed.
I recently bought an x1000 modem/router and found that after 2/3 days of staing active and properly functioning, it does not allow me to login to wifi connection with none of my devices (tried iPhone, iPad and 2 windows pc).Firmware version is v1.0.00 build 018 Sep 04, 2012
View 4 Replies View RelatedI have 2 X E4200 router, one is directly connected to the internet and the other is in the bridge mode connected to the first router. I have apple TV connected directly with the bridge router on one of the Ethernet port.I notice that when you start apple Airplay mirroring on the iPad2 both the routers will hangs with no reason and the only way to fix it is to reboot the routers. I have reset both the routers to factory default twice they both are running firmware 1.0.03 build 14 .
View 9 Replies View RelatedThe router had firmware 2.0.x(?) and I tried to update to the latest FW, according to the webpage that's
FW_E1000_2.1.02.006_US_20130115.bin
Hardware is E1000 v2 according to sticker on back.The firmware update failed (no reason given) and the router now hangs in limbo where all it does is flashing the power LED.I set my PC to 19?2.168.1.2 and TFTP'd the firmware over to 192.168.1.1 - no errors reported and 192.168.1.1 is pingable. Held reset for 30s, then powered down the router for another 30s. On power-up the router still flashes the power LED.
I have been through three chat sessions on this without resolution and support tells me just to factory reset. After some time (weeks) after a successful local login to the admin page subsequent attempt to login just hang. After entering the admin password the page changes and says "Waiting" under revolving circles. It will sit there for over 1 hour. I have tried IE, chrome and firefox on Windows 7 and Windows 8 on three different machines and it behaves the same. Of course I have to go through this same process with the support people every time and every time they come to the conclusion that I have to do a factory reset. But so far Linksys denies that there is a defect.
View 9 Replies View RelatedE3200 firmware 1.0.03 build 9. HP 1012 attached to USB port of the router. On a PC with Win7, Print Preview hangs in all applications. Print... also hangs in all applications. Reboot, re-installation of print driver, change default printer do not fix.
View 2 Replies View RelatedI recently upgraded my internet speed service from my ISP (Brighthouse). They installed a gateway to replace their old modem, but I have had it bridged so it should act as a modem. Speedtest.net shows downloads on the order of 40-50 Mbps and uploads around 5 Mbps. If I try doing something interactively that pushes the speed and size of files (like flying over Google earth using my mouse to guide the direction and speed) my connection seems to hang. I have to reset the router (unpower and repower it) to get my internet connection to work. This has also happened when I quickly downloaded a series of large images - I click to get the next page fairly soon after the current page has finished downloaded. My router is a WRT350N.
View 6 Replies View RelatedI purchased a WRT160N router last Friday. After setting it up, everything seemed to work fine, but after a couple of hours, the router stopped responding to any requests. The LEDs stayed on as if nothing had happened, but the router was dropping everything coming from both the WAN and a wired LAN interface. Since than, I had to restart it 3 times during the last 3 days.The firmware is 1.53.0, which seems to be the latest firmware for the European market - even when I try to get a newer firmware, this site only offers the US version 1.02.2.Should I update the firmware to the US version 1.02.2 ? Is there any difference between the 1.53.0 and the 1.02.2 version ? Is there a way to restore the original firmware in case the update fails ? I haven't found any link to 1.53.0 version..Also, does this firmware updating affect my warranty ?
View 9 Replies View RelatedI mistakenly downloaded and installed version 4 firmware when i should have installed version 2. My system (windows ver. 7) no longer sees the wireless router (WRT54G). I no longer have the install CD and the version 2 firmware does not seem to be available on the website. Is my router now dead in the water?
View 1 Replies View RelatedI've made an observation that the newer routers above my E3000 don't have LED icons to indicate the port is connected/active and also to show Wi-Fi is active? I find this good at a glance without having to go look in the back of the unit to see which ports are open etc.
View 1 Replies View RelatedI need to change how my security is set on my wrt54gl... it has been so long I don't know the name or password I put it under.
View 1 Replies View RelatedI have one system running as a fale server in my house, upgraded my wrt54g to an e2000 and that server cannot get through therouter. if I switch to dhcp it works fine, then switch bake to a static ip outside the dhcp range and use the same mask, gateway, nds,etc I can ping the router but can't get through it. If I then reboot the router it will work for a short time but eventually stop and I have to reboot the router again. I haven't setup any kind of restrictions or other security, server is wired not wireless.
View 2 Replies View RelatedI work from home on a Lenovo Laptop. I connect to my work network, and ultimately to a midrange ISeries. For the past year I've had no major problems with my Netgear Linksys WRT54G. I switched to a Netgear N300 last weekend because my husband's desktop was having a lot of issues. His connection is much better now.I'm able to connect to the internet with no problem, and I can access my company network & email pretty well. But, when I log on the ISeries it slows to way less than a crawl. According to my netwok icon, the connection is anywhere from 104 to 130 MBPS at any given time. But it freezes up so badly that it takes about 20 - 30 seconds just to type each letter, or to go from one window to another, or just to move the cursor down one line. It's infuriating. Every once in awhile if I disconnect and reconnect it works almost normally for awhile, but eventually slows down almost to a stop again. I actually worked for about 90 minutes the other day with no problem before it started acting up again. When I put the old G router back it works fine again. My laptop has an Intel(R) Centrino(R) Advanced-N 620 wireless adaptor. As long as I don't connect to the iseries, I have good speed and no issues with the internet or work intranet.
View 1 Replies View RelatedIm trying to install the e2500 router on my sisters macbook, but it says it is an "unsupported operating system". She has operating system 10.8.1. Why am i not able to install It?
View 1 Replies View RelatedRight now I have my computer (iMac early 2012 summer purchase) plugged directly into the wall via ethernet cable for internet access. I have only begun doing this in the past week because my E1200 wireless router has stopped working properly. I have reinstalled and reset to factory settings and set up with Cisco Connect and setup manually over the past week troubleshooting every possible way I have ever known how. My internet, obviously, is working. And when I set up the wireless network it connects properly and obtains an IP address and the lights on the back of the unit light up correspondingly and correct. But I cannot connect to the internet via the router, wirelessly or plugged directly into it. Yet when I take the internet cable and plug it straight into my computer it works.Mainly just need to know if this can be fixed or if I need to go return this unit and get a replacement. The router was purchased two months ago and has not had any issues since I first set it up until a couple of weeks ago and my phone is using up all of my cellular data plan without being connected to my wi-fi...
View 1 Replies View RelatedI have sent up a wireless network in a large building using WAG120N Modem Router and four E1000 wireless routers set as access points. The E1000's have the DHCP switched off to enable roaming so the WAG120N takes care of all that.
View 1 Replies View RelatedI'm trying to setup a DVR camera system and two web page server boxes behind a Linksys WRT54GL. The problem I have is that all of the devices want to use port 80 to generate the web page. Individually, I can get the boxes to work, but when I try to put it all together everything seems to fall apart. I've got to the DVR set to External port 80, Internal Port 80 IP address 192.168.1.254. The web page server box I try to set to External port 8001, Internal port 80, IP address 192.168.1.200, when I try to save this setting I get the error message Internet IP address and LAN IP address are in the same subnet. If I change the web page server settings to External port 8001, Internal port 8001, IP address 192.168.1.200, it will save the settings, but it won't work that way because it won't actually generate a web page when I try to access that port.The error message doesn't seem to make since as all I'm changing is the port number, not the IP address or subnet mask.
View 9 Replies View RelatedI have copied my computer's time in the router time setup under Time in the "tools" section of the router setup. After a few days of the router being up without a hard restart, it has lost 10 minutes somehow. I went to the logs and cleared them out and then looked at the entry showing that the log was cleared and looked at my computer clock and the time stamp of the log entry, and it was 10 minutes slower than my computer clock that I had originally set it from. I have a clock plugged in by the computer, and my computer always matches the clock that it plugged in, so I know it isn't my computer loosing time. What is going on here? Why does the router loose the correct time after it has been up and not unplugged or rebooted at all? I know that the router will loose the time if you unplug it, but this isn't the case here.
View 5 Replies View RelatedI cannot access the internet from my computer. The message says: runtime error program:c/windows/networkdiagnostic/xpnetdiag.exe I did two things today:
1. instal avast anti-virus (which I have since uninstalled)
2. connected my iphone 4 to my computer (perhaps for the first time)
There is no problem with the actual internet connection and there are no other problems with my computer.
(same both devices)
hostname/admin# show app ver acs
Cisco ACS VERSION INFORMATION-----------------------------Version : 5.2.0.26.8Internal Build ID : B.3417Patches :5-2-0-26-15-2-0-26-25-2-0-26-35-2-0-26-45-2-0-26-55-2-0-26-65-2-0-26-75-2-0-26-8
hostname/admin# show app status acs
ACS role: PRIMARY
[code]....
I am working on implementing ACS appliances. All working ok, until I try to add an attribute to the Shell profile (priv-lvl = 15). When I do this, the runtime process shutsdown (on both primary and secondary devices) and no further device authentications can be made. I can reinitialise the database without issue at the moment, but I'd like to know what causes this and how to prevent from happening in the future - when the database will becoem much more critical.Do I need to raise a TAC case?
On our CiscoWorks 2000 installation, running on Solaris with LMS3.2 and RME4.3.1, we noticed a few weeks ago, that the job "Inventory Collection" needs more and more time to finish. At the moment the job execution time is as high as 8 hours, compared to 3 hours before. When we look at the network traffic during job execution, we see after the collection phase (~3h) several hours with no traffic together with a very high CPU load. I mean to remember that this job used to complete around 15 minutes after data collection phase. Restarting the application and rebooting the system didn't work.When we look in to the IC_Server.log, we find devices with a completion time of over 20'000 seconds. Increasing from day to day. [code]
Affected devices are Cisco Nexus 5548P. We tried to delete/add these devices. That works for a few days, then the runtime starts to increase again.
Are we hitting a bug? And is it possible, as a workaround, to exclude devices from only the Inventory Collection?
A few weeks ago, I noticed that my Internet connection had slowed down to a crawl. I waited a few days hoping it would go away on its own, but it didn't get better. So I asked this question about how to make it faster.
The problem went away after I updated to the latest firmware, so I didn't follow up too carefully. But every few days since then, my Internet has slowed down again. Unlike before, all I have to do to fix it is open the router administration page and press the "Reboot" button. Nothing else seems to work, though I'm sure there are options I haven't tried.
If it makes a difference, my girlfriend and I both transfer large amounts of data fairly routinely for school (videoconferencing, downloading entire recorded lectures).
The router is a Cisco/Linksys WRT160N v3 that's about a year old. Most of the time, it deals with just two standard Windows 7 laptops.
What could be causing these slowdowns, and how can I get rid of them?
I installed dd-wrt on my router, and I seem to be getting higher and more consistent speeds. Perhaps more importantly, my memory use is fairly constant.
