Cisco Switching/Routing :: 6509 Connect From Access Switch With No Etherchannel
May 8, 2012
If I dual connect my access switch to my 6509s running vss, what will happen, will spanning tree still block one of the ports if I don't set up an etherchannel?
View 1 Replies
ADVERTISEMENT
Mar 25, 2013
I have two switches 6509 one switch is confire with VTP domain ABC Other switch is configure with ABZ, At present the switch is configure with the L3 interface and one fiber cable is connected between two switches.I want to remove L3 configuration wants to make L2 etherchannel and wants to ceraeate Loop back will assing same ip both side.The OSPF is configure both side , i will not do any changes in the OSPF as L3 ip is advertise in OSPF.
View 1 Replies
View Related
Jun 2, 2013
I have made an etherchannel between 6509 and 7606 with two giga interfaces on eatch one to have more bandwidth (2Go), but the Etherchannel does not exceed 1 GB (Below is a capture for Etherchannel taken from Solarwinds).the both 6506 and 7606 use ws sup 720 3bxl
View 8 Replies
View Related
Mar 5, 2012
Is it possible to use two different load balancing methods at each end of a port-channel between two switches?
We have a Cisco 6509 at one end of the port-channel and a Cisco blade switch 3020 at the other end. Right now, we are using "src-dst-ip" at both end of the port-channel. We would like to change this. That is, we would like the #3020 switch to use "src-dst-ip" while the 6509 switch should use the "src-dst-port".
Why we want to do this, the reason is that we have FWSMs on the 6509. I've read that by configuring "src-dst-port" on the 6509, one can get a better performance of traffic going through the FWSM. However, the issue is that the 3020 switch does not support "src-dst-port".
View 4 Replies
View Related
Feb 20, 2012
We have a network of 30 VLANS and currently all the vlans have access to everything. We are using Cisco 6509 switch for Layer3 routing.I would like to prevent some VLANs accessing the server VLANs. How can I restrict access to the server VLANs?Do i need to implement access-lists on the 6500 switch? or do i need to create VLANS on the firewall so that all traffic i filtered ?
View 9 Replies
View Related
Oct 21, 2012
I have vm with 2 nic card and 2 blade switch 3120g in the same hp c7000 blade enclosure. How to setup etherchannel as highlight in attachment ?
View 4 Replies
View Related
Dec 20, 2012
I have stack of 2 switches 3750?I config etherchannel between them.
here is result
2 Po2(SD) LACP Fa1/0/15(I) Fa2/0/15(I)
Both ports are up up but standalone Int port channel 2 is down down.Need to know if this is default behaviour when we config etherchannel between stack switches?
View 2 Replies
View Related
Mar 27, 2012
I have 2 6504's running HSRP as my core. They are each etherchannel'd to my Datacenter switch (3750 Stack) -- see image below.The problem i a having is with the etherchannel status:
Core1 PO11 status w (waiting)
Core2 PO11 status P(bundled)
DC11 PO48 status P -- but only to Core2 - the interfaces to Core1 are suspended. (See attached configuration documents) None of the devices have any information in the logs. I run this same configuration in my central location, but we are running Nexus 7000's. With the 6500's, do I need to split the port channels on the 3750 to allow them to negotiate the etherchannel? If I split the portchannels, are there any concerns? Should I expect to see the etherchannel status as P (Bundled) or H (Hot-Standby)?
View 2 Replies
View Related
Mar 3, 2013
configuring EtherChannel between 3750-X cross-stack and 6509E switch. I use two ports on 3750s, and two ports on 6509. I just need it as a trunk. For some elusive reason one port on 3750 keeps being err-disabled, and one on 6509 notconnected.
Here is what I did so far.
3750
!
interface GigabitEthernet1/0/22
description ***VSS-RNOC-link***
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 2
[code]....
Problem with :
GigabitEthernet1/0/22 is down, line protocol is down (err-disabled)
GigabitEthernet2/1/29 is down, line protocol is down (notconnect)
I tried shutting them down, then no shutting them again. Didn't work.
View 11 Replies
View Related
Sep 26, 2012
I came across this Multichassis EtherChannel Features when read about information from Cisco Smart Business Architecture.After checking further, knowing that Cataly stwitch 6500 supports this feature.provide information that beside Catalyst 6500, is there any other model of Catalyst switch can support this feature?
View 4 Replies
View Related
Apr 1, 2013
I am trying to use a Tekradius Windows2008 server to aaa authenticate switch admin logins. The Radius server and 6509 loop0 are in a management VRF "netman". I can happily ping to and from the Server and loopback0 interface without issue. I have also tested the radius server account using RadiusNT on a workstation. I get an accept reply with the following variables..
shell:priv-lvl=15
NAS-Prompt
Here are the relevant parts of my config as far as I can see..
aaa new-model
aaa group server radius SRADIUS
server-private 192.168.1.101 auth-port 1812 acct-port 1813 key cisco
ip vrf forwarding netman
ip radius source-interface Loopback0
!
aaa authentication login default group SRADIUS local
[code]...
View 1 Replies
View Related
Sep 20, 2012
Im having a strange problem on a 6509 switch. I am trying to use a Tekradius Windows2008 server to aaa authenticate switch admin logins. The Radius server and 6509 loop0 are in a management VRF "netman". I can happily ping to and from the Server and loopback0 interface without issue. I have also tested the radius server account using RadiusNT on a workstation. [code]
View 8 Replies
View Related
Jan 21, 2013
I have a 6509 running catOS that i had to do some routing changes on this weekend. I guess i forgot to set the default route so now I can't login or ping from outside the local subnet and because of acl restrictions on the vty lines can't login from a device within the local subnet. I can login to the sup module so i'm trying to figure out if there is way to get to the switch from the sup like you would access the sup from the switch by inputting the command session 15 or session 16, is there a way to do the reverse to get to the switch from the sup?
View 1 Replies
View Related
Feb 6, 2013
I have number of 6500 switches and we are in the process of getting support contract renewed now when i buy support for my 6500 series switches i have to inform main module serial numbers (Only this one). or do i also have to inform about sub module serial numbers to my support vendor?
View 1 Replies
View Related
Apr 3, 2012
i am trying to configure my HP 420 access point. I have configure different SSID on it, This access point is connected to cisco 4500 switch, i have configure trunk on up link to access point.my problem is the client are not able to get an IP address form the correct vlan if i tagged the SSID to it.
in the following the output of show run int in cisco 4500 switch:
interface GigabitEthernet3/13
description ==== HP ACCess point ====
switchport trunk allowed vlan 99,130,132
switchport mode trunk
[code]....
View 1 Replies
View Related
Jul 31, 2012
Suffered a big outage on the network, the fix was to reload the module 3 on the 6509 switch, we had these errors on the log %CONST_DIAG-SW1_SP-3-HM_PORT_TEST_FAIL: Switch 1 Module 3 TestUnusedPortLoopback Port(s)[24,46] failed. System operation continues.in the end, we reloaded the card and it was all ok. is there anything I can do to check the card / or any deeper logs? would that error cause the card to crash?
View 1 Replies
View Related
Aug 28, 2012
I have a 6509-E chassis that was prevoius in a VSS configuration. Due to some VSL failures I had to cobvert it to a standalone chassis but would like to bring it back to a virtual system.
Whenever I try to convert it by using the command "switch convert mode virtual" I get the msg %Please configure local switch number first". After doing so by entering the CLI cmd "switch set switch_num 1 local" I still get the same message.
View 1 Replies
View Related
Feb 21, 2012
in my 6509 switch while i checked is showing some thing like this RDCCI65F0#sh environment
environmental alarms:
no alarms
backplane:
operating clock count: 2
[Code].....
View 2 Replies
View Related
Jan 13, 2012
I have configured cisco 6509 to do nating and its not working. Static nat is perfectly working fine below is the config.
View 6 Replies
View Related
May 16, 2010
I have one CISCO 6509 Switch in my store. I tired to login in that switch but couldnt.. Once it's booted it's asking me: rd: . Find the attachment. I recover the password by changing confreg value but that also failed.
View 8 Replies
View Related
Dec 11, 2012
How a 6509 pair handles the loss of the other vss switch, and what happens when the other comes back on ?
View 1 Replies
View Related
May 19, 2012
I have a 6509 that has dual SUP32's.Just want to make sure and give a reason(if there is one). Slot 6 always becomes the active hot on a full reboot. Meaning from no power to the whole switch to powered on. What is the election process for Supervisors?
View 5 Replies
View Related
Feb 6, 2013
I am doing a deployment of a cat 6509
Any checklists that they fill in pre deployment, ie card failover tests etc ?
View 1 Replies
View Related
Jul 5, 2012
I was trying to uplink a switch today on a 1500m run of SMF. I have a 6509 core switch with a 16 port GBIC module. On that end I have a WS-G5486-LX with a 3m SC to LC patch cable.On the other end I have a 3750G with a GLC-LH-SM SFP. I have checked my fiber path and it seems good, (by sight, did not have an OTDR avialable).I can't get the link up at all. Tried swapping Tx Rx at one end, Tried different transceivers. Tried different patch cables. Nothing worked. At about the mid-point of my fiber run the cable passes through another network closet with a core switch for a separate network. If I break my fiber path there and try to connect in either direction it works. The only differences are the length of the fiber run and that the core switch on the other network has a CLC-LX-SM SFP.Is it the distance? Or is there some issue connecting a GLC-LH-SM to a WS-G5486-LX?
View 7 Replies
View Related
Apr 16, 2012
i have one of my switch modules that shows PwrDown when i issue the command show mod.
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 9 Supervisor Engine 32 8GE (Active) WS-SUP32-GE-3B SAD09120263
2 48 48 port 10/100/1000mb EtherModule WS-X6148-GE-TX SAL1029VWZ5
[Code]....
i tried disabling the diagnostic monitor for the module, did a power enable module command and then reset it but it still fails. this is the third blade that i am replacing in a few weeks and i still get the same error. i am persuded that it is not a hardware since it is the third blade in a matter of weeks. after the module reset, i receive this error % module 3 is operationally off (FRU-power failed)
could an ios upgrade solve this issue? are there any ios related bugs?
View 10 Replies
View Related
Nov 28, 2012
We have a cisco catalyst 6509 with Supervisor Engine . After power outage, the switch always start in Rommon mode. Configuration register is 0X2102, we want to it always start in normal mode. What should i do?
View 3 Replies
View Related
Nov 30, 2012
I need to replace a faulty fan unit on the catos WS-6509 switch. this Catos switch does not support show inventory so any other catos commands which will show me this part id?
View 2 Replies
View Related
Jan 25, 2012
i'm already has one internet connection is conecting directily to the Core Switch 6509, and the Switch is route any internet request with default route:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.170.10.10
10.170.10.10 is --> Next hop for the DSL router internal IP, and it's working fine.
We have a new internet connection with another ISP/ with another DSL router, how to connect both of them to exit from the Core Switch 6509.
is it ok if i make another default route to the Next hop to the new DSL router as:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.80.10.10
10.80.10.10 is --> Next hop for the new DSL router internal IP.
View 6 Replies
View Related
Oct 14, 2012
I recently ran an upgrade on my 6509-E's and when the first switch came back up, 3 of the 10/100 switches that were in the chassis did not power on. After further investigation, these models are not supported by this latest IOS version. The module # is : WS-X6248-RJ-45
We have one WS-X6348-RJ-45 and since it was a few weeks ago I did this I can't remember for sure but I believe this one came up.
Where can I found the information regarding this being unsupported but I know it is out there and any page that showed me that this was unsupported with the latest stable IOS of 12.(33).
In addition to this question, I have approval to purchase some newer gigabit switches that will be supported by this new IOS version and hopefully at least the next few over the next few years. Which specific gig models are currently and hopefully should be supported for the next few years? I don't need PoE or anything spectacular, just regular switches that are attached to either servers or virtual hosts. I've been looking at the lists of what is out there and it seems like there are hundreds of different models and it is becoming difficult to determine what is what.
View 1 Replies
View Related
Aug 15, 2012
I have seen links out there for a conversion tool to convert commands on a Catalyst type switch (6509) to newer IOS type switches(4500-e) switches but they all error out on me on a 404. Any link where I can get this conversion tool?
View 1 Replies
View Related
Mar 16, 2013
I am getting very slow window file transfer speed (4 Mbps per second) between two connecting servers in Cisco 6509 switch. I have connect the two laptops in 6509 switch in same module using the same vlan and try to copy the files from one laptop to another and vice versa and got the same speed on 4 to 5 Mbps per second. Switch utilization is not more than 10% and both the laptops are connected in 1 Gbps full duplex.
I have checked by removing the gateway in both laptop but the output is same.
View 7 Replies
View Related
Feb 2, 2013
I am planning to upgrade the current core switch(3750) to 6509 series switch. Since we have a production network running we have to plan for an online core switch upgrade.
View 7 Replies
View Related
Oct 23, 2011
What is PIM? give me an example when I will use and not use the PIM command.
View 4 Replies
View Related