Cisco Switching/Routing :: AAA Authentication On 6509 Switch

Sep 20, 2012

Im having a strange problem on a 6509 switch. I am trying to use a Tekradius Windows2008 server to aaa authenticate switch admin logins. The Radius server and 6509 loop0 are in a management VRF "netman". I can happily ping to and from the Server and loopback0 interface without issue. I have also tested the radius server account using RadiusNT on a workstation. [code]

View 8 Replies


ADVERTISEMENT

Cisco Switching/Routing :: AAA Authentication On 6509 Switch?

Apr 1, 2013

I am trying to use a Tekradius Windows2008 server to aaa authenticate switch admin logins. The Radius server and 6509 loop0 are in a management VRF "netman". I can happily ping to and from the Server and loopback0 interface without issue. I have also tested the radius server account using RadiusNT on a workstation. I get an accept reply with the following variables..
 
shell:priv-lvl=15
NAS-Prompt
 
Here are the relevant parts of my config as far as I can see..
 
aaa new-model
aaa group server radius SRADIUS
server-private 192.168.1.101 auth-port 1812 acct-port 1813 key cisco
ip vrf forwarding netman
ip radius source-interface Loopback0
!
aaa authentication login default group SRADIUS local

[code]...

View 1 Replies View Related

Cisco Switching/Routing :: Accessing 6509 Switch From Sup?

Jan 21, 2013

I have a 6509 running catOS that i had to do some routing changes on this weekend. I guess i forgot to set the default route so now I can't login or ping from outside the local subnet and because of acl restrictions on the vty lines can't login from a device within the local subnet. I can login to the sup module so i'm trying to figure out if there is way to get to the switch from the sup like you would access the sup from the switch by inputting the command session 15 or session 16, is there a way to do the reverse to get to the switch from the sup?

View 1 Replies View Related

Cisco Switching/Routing :: Support For 6509 Switch

Feb 6, 2013

I have number of 6500 switches and we are in the process of getting support contract renewed now when i buy support for my 6500 series switches i have to inform main module serial numbers (Only this one). or do i also have to inform about sub module serial numbers to my support vendor?

View 1 Replies View Related

Cisco Switching/Routing :: To Reload The Module 3 On The 6509 Switch

Jul 31, 2012

Suffered a big outage on the network, the fix was to reload the module 3 on the 6509 switch, we had these errors on the log %CONST_DIAG-SW1_SP-3-HM_PORT_TEST_FAIL: Switch 1 Module 3 TestUnusedPortLoopback Port(s)[24,46] failed. System operation continues.in the end, we reloaded the card and it was all ok. is there anything I can do to check the card / or any deeper logs? would that error cause the card to crash?

View 1 Replies View Related

Cisco Switching/Routing :: 6509-E / VSS - Unable To Set Switch Number

Aug 28, 2012

I have a 6509-E chassis that was prevoius in a VSS configuration. Due to some VSL failures I had to cobvert it to a standalone chassis but would like to bring it back to a virtual system.

Whenever I try to convert it by using the command "switch convert mode virtual" I get the msg %Please configure local switch number first". After doing so by entering the CLI cmd "switch set switch_num 1 local" I still get the same message.

View 1 Replies View Related

Cisco Switching/Routing :: 6509 Fan Failed But Switch Is Still Running?

Feb 21, 2012

in my 6509 switch  while i checked  is showing some thing like this RDCCI65F0#sh environment

environmental alarms:
no alarms
backplane:
operating clock count: 2

[Code].....

View 2 Replies View Related

Cisco Switching/Routing :: NATing Not Working On 6509 Switch

Jan 13, 2012

I have configured cisco 6509 to do nating and its not working. Static nat is perfectly working fine below is the config.

View 6 Replies View Related

Cisco Switching/Routing :: Password Recovery For 6509 Switch?

May 16, 2010

I have one CISCO 6509 Switch in my store. I tired to login in that switch but couldnt.. Once it's booted it's asking me: rd: . Find the attachment. I recover the password by changing confreg value but that also failed.

View 8 Replies View Related

Cisco Switching/Routing :: 6509 How Vss Handle Loss Of Switch

Dec 11, 2012

How a 6509 pair handles the loss of the other vss switch, and what happens when the other comes back on ?

View 1 Replies View Related

Cisco Switching/Routing :: 6509 No Power To Whole Switch To Powered On

May 19, 2012

I have a 6509 that has dual SUP32's.Just want to make sure and give a reason(if there is one).   Slot 6 always becomes the active hot on a full reboot.  Meaning from no power to the whole switch to powered on. What is the election process for Supervisors?

View 5 Replies View Related

Cisco Switching/Routing :: Pre Deployment Tests For Switch 6509

Feb 6, 2013

I am doing a deployment of a cat 6509
 
Any checklists that they fill in pre deployment, ie card failover tests etc ?

View 1 Replies View Related

Cisco Switching/Routing :: 6509 Connect From Access Switch With No Etherchannel

May 8, 2012

If I dual connect my access switch to my 6509s running vss, what will happen, will spanning tree still block one of the ports if I don't set up an etherchannel?

View 1 Replies View Related

Cisco Switching/Routing :: 6509 Uplink A Switch Today On 1500m Run Of SMF

Jul 5, 2012

I was trying to uplink a switch today on a 1500m run of SMF. I have a 6509 core switch with a 16 port GBIC module. On that end I have a WS-G5486-LX with a 3m SC to LC patch cable.On the other end I have a 3750G with a GLC-LH-SM SFP. I have checked my fiber path and it seems good, (by sight, did not have an OTDR avialable).I can't get the link up at all. Tried swapping Tx Rx at one end, Tried different transceivers. Tried different patch cables. Nothing worked. At about the mid-point of my fiber run the cable passes through another network closet with a core switch for a separate network. If I break my fiber path there and try to connect in either direction it works. The only differences are the length of the fiber run and that the core switch on the other network has a CLC-LX-SM SFP.Is it the distance? Or is there some issue connecting a GLC-LH-SM to a WS-G5486-LX?

View 7 Replies View Related

Cisco Switching/Routing :: 6509 Switch Blade Shows Power Down

Apr 16, 2012

i have one of my switch modules that shows PwrDown when i issue the command show mod.
 
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
1    9  Supervisor Engine 32 8GE (Active)      WS-SUP32-GE-3B     SAD09120263
2   48  48 port 10/100/1000mb EtherModule      WS-X6148-GE-TX     SAL1029VWZ5

[Code]....
 
i tried disabling the diagnostic monitor for the module, did a power enable module command and then reset it but it still fails. this is the third blade that i am replacing in a few weeks and i still get the same error. i am persuded that it is not a hardware since it is the third blade in a matter of weeks. after the module reset, i receive this error % module 3 is operationally off (FRU-power failed)
 
could an ios upgrade solve this issue? are there any ios related bugs?

View 10 Replies View Related

Cisco Switching/Routing :: 6509 Switch To Restrict Access To Sensitive Vlans

Feb 20, 2012

We have a network of 30 VLANS and currently all the vlans have access to everything. We are using Cisco 6509 switch for Layer3 routing.I would like to prevent some VLANs accessing the server VLANs. How can I restrict access to the server VLANs?Do i need to implement access-lists on the 6500 switch? or do i need to create VLANS on the firewall so that all traffic i filtered ?

View 9 Replies View Related

Cisco Switching/Routing :: Switch 6509 In ROMmon Mode After Power Outage?

Nov 28, 2012

We have a cisco catalyst 6509 with Supervisor Engine . After power outage, the switch always start in Rommon mode. Configuration register is 0X2102,  we want to it always start in normal mode. What should i do?

View 3 Replies View Related

Cisco Switching/Routing :: Replace Faulty Fan Unit On Catos WS-6509 Switch

Nov 30, 2012

I need to replace a faulty fan unit on the catos WS-6509 switch. this Catos switch does not support show inventory so any other catos commands which will show me this part id?

View 2 Replies View Related

Cisco Switching/Routing :: 2 Internet Connection Connected To Same Core Switch 6509

Jan 25, 2012

i'm already has one internet connection is conecting directily to the Core Switch 6509, and the Switch is route any internet request with default route:
 
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.170.10.10
 
10.170.10.10 is --> Next hop for the DSL router internal IP, and it's working fine.
 
We have a new internet connection with another ISP/ with another DSL router, how to connect both of them to exit from the Core Switch 6509.
 
is it ok if i make another default route to the Next hop to the new DSL router as:
 
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.80.10.10
 
10.80.10.10 is --> Next hop for the new DSL router internal IP.

View 6 Replies View Related

Cisco Switching/Routing :: 6509-E Supported Switch Modules With Latest Stable IOS 12.(33)

Oct 14, 2012

I recently ran an upgrade on my 6509-E's and when the first switch came back up, 3 of the 10/100 switches that were in the chassis did not power on. After further investigation, these models are not supported by this latest IOS version. The module # is : WS-X6248-RJ-45
 
We have one WS-X6348-RJ-45 and since it was a few weeks ago I did this I can't remember for sure but I believe this one came up.
 
Where can I found the information regarding this being unsupported but I know it is out there and any page that showed me that this was unsupported with the latest stable IOS of 12.(33).
 
In addition to this question, I have approval to purchase some newer gigabit switches that will be supported by this new IOS version and hopefully at least the next few over the next few years. Which specific gig models are currently and hopefully should be supported for the next few years? I don't need PoE or anything spectacular, just regular switches that are attached to either servers or virtual hosts. I've been looking at the lists of what is out there and it seems like there are hundreds of different models and it is becoming difficult to determine what is what.

View 1 Replies View Related

Cisco Switching/Routing :: Conversion Tool For Catalyst (6509) To 4500-e IOS Switch?

Aug 15, 2012

I have seen links out there for a conversion tool to convert commands on a Catalyst type switch (6509) to newer IOS type switches(4500-e) switches but they all error out on me on a 404. Any link where I can get this conversion tool?

View 1 Replies View Related

Cisco Switching/Routing :: Slow File Transfer Speed In Same Vlan Of 6509 Switch

Mar 16, 2013

I am getting very slow window file transfer speed (4 Mbps per second) between two connecting servers in Cisco 6509 switch. I have connect the two laptops in 6509 switch in same module using the same vlan and try to copy the files from one laptop to another and vice versa and got the same speed on 4 to 5 Mbps per second. Switch utilization is not more than 10% and both the laptops are connected in 1 Gbps full duplex.
 
I have checked by removing the gateway in both laptop but the output is same.

View 7 Replies View Related

Cisco Switching/Routing :: 3750 / 6509 - Upgrade Core Switch Without Disrupting Network?

Feb 2, 2013

I am planning to upgrade the current core switch(3750) to 6509 series switch. Since we have a production network running we have to plan for an online core switch upgrade.

View 7 Replies View Related

Cisco Switching/Routing :: 6509 Core Switch Command / IP PIM Sparse-dense-mode

Oct 23, 2011

What is PIM? give me an example when I will use and not use the PIM command.

View 4 Replies View Related

Cisco Switching/Routing :: Configure 802.1x RADIUS Authentication On 2950-24TT-L Switch?

May 3, 2013

I am trying to configure 802.1x RADIUS Authentication on cisco 2950-24TT-L Switch. I am using following set of command as given below
 
Switch# configure t
Switch(config)# aaa new-model
Switch(config)# aaa authentication dotx default group redius
Switch(config)# dot1x system-auth-control
Switch(config)# inter fasteth 0/1
Switch(config)#dot1x port-control atuo
 
I am facing problem dot1x command is not working on interface.

View 1 Replies View Related

Cisco Switching/Routing :: Limit For Creation Of Port Chanel In Core Switch 6509 And 6513

Feb 20, 2012

How much is the limit for the creation of PortChanel in a Core Switch 6509 and 6513?Is there a limitation byu hardware?

View 7 Replies View Related

Cisco Switching/Routing :: 6509 - 802.1x And Voice VLAN / Enable Dot1x On User's Ports On The Switch

Sep 17, 2012

I have a Cisco 6509 with IOS "s222-ipservicesk9_wan-mz.122-18.SXF16.bin"I need to enable dot1x on user's ports on the switch. each user is connected to the switch through the IP phone.
 
I just found out that I can not enabled dot1x on trunk port. I have tried to use "switchport voice vlan " but I got:
 
Switch(config-if)#switchport voice vlan 123
Command rejected: Gi7/20 is Dot1x enabled port.
 
let me know what should I do to get dot1x working?
 
Note: I have connected a laptop directly to the port and dot1x is working fine.

View 5 Replies View Related

Cisco Switching/Routing :: 6509 - Configure Multiple Dhcp Pools On Switch For Multiple VLANs

Mar 9, 2010

Is it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.

View 5 Replies View Related

Cisco Switching/Routing :: 6509 To 6509-E Chassis Upgrade?

Nov 21, 2011

I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:

     x3     48 ports
     x1     NAM
     x2     Sup720
     Running 12.2(18)SXF3
 
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?

View 2 Replies View Related

Cisco Switching/Routing :: Upgrade Of 6509 To 6509-E Chassis

Nov 21, 2011

I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:

x3     48 ports
x1     NAM
x2     Sup720

Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?

View 2 Replies View Related

Cisco Switching/Routing :: 6509 / 4900 - Network Down Cause Switching Supervisor With Redundancy

Jan 11, 2012

we've had an issue with our network, we have 2 6509 connected with redundancy, which are connected with 2 x 4900 Switches, from which are connected to a ESX Chassis for visualization, the thing is that the ESX stopped working, and the 4900 switches, and the main core were suffering from overload, they hang on it very well, in order to stop the overload, one of the links to the ESX Chassis were disconnected from one of the 4900 switches. The CPU usage from the 4900 and the core(6509) went down below 40%, and then they started to migrate the virtual servers from the chassis to another 2 chassis that were added right after. They were actually working well, but suddenly the 6509 changed to the other supervisor after everything was OK. We were wondering what could have been the cause of this, maybe the virtual servers migrations, maybe the overload from the ESX ? We also had a few question, is there any need to reload the cores every few months as a planned task ? Because the cores have been up for more than 1 year. And also is there any kind of of tool to monitor the CPU status, or the status overall from the cores or the switches ?

View 3 Replies View Related

Cisco Switching/Routing :: 6509 - Upgrading Switching Infrastructure

Apr 11, 2012

The have around 80 staff and I think the current infrastructure is overkill for the size of the company. The current kit is old and they have no GB ethernet ports. They currently have:-

Core Switch:
1x Cisco c6509with a 48 port fast ethernet module (WS-X6248-RJ-45)
and an 8 port fibre module (WS-X6408A-GBIC)

I'm looking to replace this with something with 72 ethernet ports and 8 fibre ports

Access Switches:
2x 3500Replacement needs at least 48 ports and 2 fibre modules each

and 2x 5500Replacement needs at least 72 ports and 2 fibre modules each.

View 13 Replies View Related

Cisco Switching/Routing :: Policy Routing Based On Client Gateway (6509-E)

Feb 26, 2012

If client gateway = 192.168.64.9 then next-hop = 192.168.64.8 else use default-route 0.0.0.0
 
I know it's possible to do a route-map match ip-address ACL list. But is it possible to match on gateway?
 
Some info about hardware and config:

6509-E in VSS (IOS 12.2(17r)SX5) withVS-S720-10G supervisor.

All routes are static, IP for 192.168.64.9 is on SVI vlan.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved