I have a remote 3G Cisco router (Cisco 819) that occastionally drops it's EzyVPN and the local guys just reboot the device so when I log on and check the logs it is empty. My syslog server shows very little, can I keep the logs locally or up the logging to the syslog server?
View 1 RepliesI have saved the running configuration to startup first and rebooted the ACS 5.1. Since then it has stopped Authentication logs, though I can login to the network devices using Tacacs login, but I am not getting Tacacs authentication logs ?
View 3 Replies View Related%SYSTEM_CONTROLLER-SP-3-ERROR: Error condition detected: TM_DATA_PARITY_ERROR Feb 2 10:57:09.602 EST: %SYSTEM_CONTROLLER-SP-3-EXCESSIVE_RESET: System Controller is getting reset so frequently
Cisco Internetwork Operating System Software
IOS (tm) s222_rp Software (s222_rp-IPSERVICES_WAN-M), Version 12.2(18)SXF15a, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2008 by cisco Systems, Inc.
Compiled Mon 20-Oct-08 19:20 by kellythw
Image text-base: 0x40101040, data-base: 0x42951080
[code]....
I am having some issues on my network and i think i have narrowed them down to a single switch.
On this switch the following logs can be seen
2147482407 05-May-2012 15:40:54 Informational %AAA-I-CONNECT: New http connection for user admin, source 10.0.5.135 destination 10.0.5.172 ACCEPTED
2147482431 05-May-2012 09:03:31 Warning %STP-W-PORTSTATUS: g13: STP status Forwarding
2147482432 05-May-2012 09:03:01 Informational %LINK-I-Up: g13
[code]......
All other switches are OK and do not show anything in their logs. I am trying to figure out what could be going wrong. Spanning tree is enabled on all switches. The switch tihs is happening on, ends in the ip 172 and is where all building cables connect to. They also connect to 174. I have attached an image of the infrastructure so you can visually see what i mean.
I am getting continous logs on my 4507 Switch :
May 16 12:45:09.000: %C4K_RKNOVA-4-INVALIDTOKENEXPIRED: STANDBY: Suppressed 302 times)Expired token 16490 in the invalid token list (NumEntries: 6) of type IrmPortId other id == 4294967287
May 16 12:45:09.000: %C4K_RKNOVA-4-INVALIDTOKENEXPIRED: STANDBY: Suppressed 302 times)Expired token 16490 in the invalid token list (NumEntries: 6) of type IrmPortId other id == 4294967287
does it lead to high CPU utilisation as well ??
It looks like both my HSRP Interfaces (VLAN 600 & 700) cycle through standby --> active ---> speak continuously on one of the two switches. What can be causing this?
*May 4 06:41:24.883: %HSRP-5-STATECHANGE: Vlan700 Grp 0 state Speak -> Standby
*May 4 06:41:33.671: %HSRP-5-STATECHANGE: Vlan700 Grp 0 state Standby -> Active
*May 4 06:41:33.671: %HSRP-5-STATECHANGE: Vlan700 Grp 0 state Active -> Speak
*May 4 06:41:34.251: %HSRP-5-STATECHANGE: Vlan700 Grp 0 state Speak -> Standby
*May 4 06:41:47.691: %HSRP-5-STATECHANGE: Vlan700 Grp 0 state Standby -> Active
*May 4 06:41:47.703: %HSRP-5-STATECHANGE: Vlan700 Grp 0 state Active -> Speak
I have got a l2 link of 512 kbps from two different ISP. I want to aggegrate the bandwidth of this connection so that I can feel like having 1 mbps connection. I am not actually talking about load balancing, but bandwidth/link aggegration. Can we have the solution of failover with different vlan from different isp ? Can we be able to make the link as a single link.
View 2 Replies View RelatedI am not getting interface up/down logs in my switch console through show logging command. Switch model cisco WS-C4506-E and IOS :- cat4500e-ipbasek9-mz.122-53.SG3.bin. I have done below mention configurations, we can't configure logging level beyond informational. [code]
View 4 Replies View RelatedOur customer is having C6513 running with 12.2(18)SXF15a . One of the module (ACE20-MOD-K9) got rebooted with following error:
Feb 22 10:41:41.155 GMT: %OIR-SP-3-PWRCYCLE: Card in module 6, is being power-cycled off (Reset - Module Reloaded During Download)Feb 22 10:41:41.183 GMT: %C6KPWR-SP-4-DISABLED: power to module in slot 6 set off (Reset - Module Reloaded During Download)Feb 22 10:41:53.686 GMT: %OIR-SP-3-PWRCYCLE: Card in module 6, is being power-cycled off (Module not responding to Keep Alive polling)Feb 22 10:41:53.686 GMT: %C6KPWR-SP-4-DISABLED: power to module in slot 6 set off (Module not responding to Keep Alive polling)
Code...
We are getting some error logs on Nexus VDC,as follows:2012 Nov 23 08:49:11 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 6 times 2012 Nov 23 08:50:21 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 7 times 2012 Nov 23 08:49:11 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 6 times2012 Nov 23 08:50:21 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 7 times.
View 1 Replies View RelatedWe use C2950G switches with IOS 12.1(22)EA12 . Switches are set up to send logs to a server (informationnal level). On this server, we receive many of logs from those switches, but none about interfaces errors (even if interfaces statistics show interfaces errors). On C3548 switches it's work fine.How should I be sure the set up of switches is correct ? Why do I never receive messages as %LINK-4-ERROR:[char] is experiencing errors ?
View 2 Replies View RelatedBelow memory status alerts of are seen on our syslog server for Nexus 7K switch(Default VDC).
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : CRITICAL ALERT RECOVERED
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : MINOR ALERT RECOVERED
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : SEVERE ALERT RECOVERED
Memory threshold Not created on Nexus. Can we ignore this alert or does it impact our current network traffic?
I m getting below error messages in show logs -
Aug 12 15:30:57.127 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:02.175 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:08.219 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:10.239 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
there is no error messages related to PSU in "show env all " log .
here is show version -
------------------ show version ------------------
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA13, RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2009 by cisco Systems, Inc.
[Code] ....
How i can transfer the router logs to email address.Wev are using the router 2600.
View 5 Replies View RelatedWe are getting some error logs on Nexus switch 7K.
Loggs:
----------
2012 Oct 30 22:36:07 SWITCH %CMPPROXY-STANDBY-2-LOG_CMP_UP: Connectivity Management processor(on module 6) is now UP
2012 Oct 30 22:36:40 SWITCH %SYSMGR-2-GSYNC_SNAPSHOT_SRVFAILED: Service "ipqosmgr" on active supervisor failed to sto
re its snapshot (error-id 0x40480005).
2012 Oct 30 22:36:40 SWITCH %SYSMGR-2-STANDBY_BOOT_FAILED: Standby supervisor failed to boot up.
2012 Oct 30 22:36:42 SWITCH %PLATFORM-2-MOD_REMOVE: Module 6 removed (Serial number JAF1550ATBR)
2012 Oct 30 22:42:08 SWITCH %BOOTVAR-5-NEIGHBOR_UPDATE_AUTOCOPY: auto-copy supported by neighbor supervisor, starting
[code]....
it is possible to schedule when to send logs to a syslog server (Switch Catalyst 3560) ?
View 3 Replies View RelatedWe are getting log messages like
%EARL-DFC4-4-NF_USAGE: Current Netflow Table Utilization is 95%
%EARL-DFC4-4-NF_USAGE: Current Netflow Table Utilization is 99%
What this messages really means and how to get rid of these messages. We are using IOS version 12.2(33)SXJ in Catalyst 6500.
We have a stack of 4 Cisco WS-3750G-24TS with Sw Version 12.2(52) SE and giving weird errors:-
-Traceback= 17211C8 16FA4C0 16FA4FC 18625E4 18608D4 286A850 283E6FC 282EDF4 2859BBC 1B2EDA8 1B25878
Oct 17 22:26:48 AEDT: %SNMP-3-CPUHOG: Processing GetBulk of lldpRemEntry.7
Oct 17 22:26:50 AEDT: %SYS-3-CPUHOG: Task is running for (2098)msecs, more than (2000)msecs (8/6),process = SNMP ENGINE.
-Traceback= 172108C 17211CC 16FA4C0 16FA4FC 18625E4 18608D4 286A850 283E6FC 282EDF4 2859BBC 1B2EDA8 1B25878
Oct 17 22:26:51 AEDT: %SNMP-3-CPUHOG: Processing GetBulk of lldpRemEntry.7
Oct 17 22:26:53 AEDT: %SNMP-3-CPUHOG: Processing GetBulk of lldpRemEntry.6
Oct 17 22:26:53 AEDT: %SYS-3-CPUHOG: Task is running for (2097)msecs, more than (2000)msecs (1/1),process = SNMP ENGINE.
What are these errors is this a bug in the IOS
I have configured my 2951 router to send logs to my Kiwi syslog server like below.
#logging 10.20.20.52
But I am not receiving any logs from my router, the same has configured on my asa5520 and its sending logs.
We have a Nx5548up pair connected to FI6248 via a vPC. We had to reboot a FI (in order to configure more FC ports) ; following that reboot, we meet many issues.The first log shows the vPC down showing the FI rebbot.2013 May 23 12:31:45 sw-n5kup-fr-eqx-01 %ETH_PORT_CHANNEL-5 PORT_INDIVIDUAL_DOWN: individual port Ethernet1/2 is down
View 1 Replies View RelatedI have 3560X-24T-S switches with IP Services loaded at remote sites that I have been having troubles with. Originally, they had IOS 12.2(58)SE1 on them. I have up to four diverse paths via point-to-point microwave at the remote sites. The Microwave equipment is by Microwave Networks and is a Prodeus M series which Ethernet support. The original issue manifested itself as hardware loopback errors on some of the ports that were connected to the microwave links.
My experience in the past has been that when a hardware loopback error occurred it is usually a bad switch port. In this case however, if I disconnected all of the microwave Ethernet links and rebooted the switch and then connected the Ethernet connections to the microwave links again, everything works fine. No hardware loopback errors. That is, until the next switch reboot. Then the hardware loopback error would return. Interestingly, it would come back on different ports connected to the microwave links every time. So if a reboot was done without disconnecting the microwave Ethernet links the hardware loopback error would change from one microwave link to another after each reboot.
I then went through and read the lengthy release notes for IOS version 15.0(2)SE and found several fixes that I thought could fix my issue. So I downloaded it and updated a couple of the offending switches (not all of them were having this problem). After going through the second update required to resolve the 'open file error' that happens going between 12.2(58)SE1 and 15.0(2)SE the problem seemed to be resolved on the offending switches. So, I went ahead and updated the IOS on all of the switches with point-to-point microwave connections.
I now have one switch that was updated that is crashing and rebooting continuously when the Ethernet links for the point-to-point microwave are connected. Again, if I disconnect all the microwave links and reboot, it comes up fine ands stays fine when the microwave links are connected back up. It will work fine until the next reboot and then the crash and reboot loop starts over again. Below is a portion of the putty log when the crash occurs:
----------------------------------------------------------------------------------------------------------------------
previous memory block, bp = 0x59BF838,
memorypool type is Processor
data check, ptr = 0x59BF860
========= Dump bp = 0x59BF87C ======================
59BF77C: 0 0 0 FD0110DF AB1234CD FFFE0000 56 383FDB4
59BF79C: 212AC68 59BF838 59BF6F4 80000042 1 0 A504F53 543A2050
59BF7BC: 6F727441 53494320 506F7274 204C6F6F 70626163 6B205465 73747320 3A20456E
[code].....
I am facing a problem with a cisco 6509 that goes into rommon every time i restart. If i give the command
rommon 1> boot
it will pick up the IOS on the sup-bootdisk: or bootdisk: and boots up but i dont understand why on reboot it wont pick up this IOS and boot itself and why do i have to write boot command everytime on rommon.
I have also explicitly given the command "boot system bootdisk:IOSNAME.bin" in the startup config file but still no luck.
Need your expert input in sorting out the below problem.I have a cisco 6513 switch which is going into SP mode after a reboot whci i have done during BCP activity in my organization.Below are the log for your reference.
Code...
Yesterday my router was hangs and my services was stuck. I start the router hard booted and it works fine.This was second time i was facing this kind of scenario. The attached are the "show tech support" of the cisco router 2821.
View 2 Replies View RelatedWe recently wanted to swap our existing WS-SUP720-base with a WS-SUP720-3B in a 6513 chassis.Had the existing configuration config saved in a txt file and replaced the supervisor. Booting went fine and we pasted in the original config. There was one failure message about unnsupported command but didnt take further notice."boot system flash sup-bootflash:" was probaly the line that the 720-3B didnt support.After wr mem and reload it went in continious loop and rebooting due to inncorrect boot device. Had to put back the old supervisor and have now the 720-3B in a 6504 chassis. Tried some commands in rommon, but are not getting any further.
View 8 Replies View RelatedOur 6500 was reboot by self with crash info and i found it was happened by CPU HOG. The log is below for CPU HOG and you can see many times from attached crash info file.
%SYS-SP-3-CPUHOG: Task is running for (16000)m secs, more than (2000)m secs (15/12),process = RPC pagp_switch_mp2sp.
[code]....
I think this process made high CPU & memory issue and then there were internal communication fail.. isn't it? So i need to know what PRC pagp_switch_mp2sp is to prevent next issue.
I have 2 Catalyst 2960S-switches configured in a stack. The uplink is configured as a cross-stack etherchannel. Now I want to upgrade the stack with a minimum of downtime for the connected hosts. The hosts are connected to the stack via cross-stack etherchannels. So my question is: How can I upgrade the stack and reboot the members with a minimum of downtime? If I use the archive download-sw command with the /reload-option, the stack is reloaded and the result will be downtime for the hosts while th stack is reloading. Is it possible to upgrade the stack and then reboot the members one by one in a controlled manner?
View 8 Replies View RelatedI have multiple 6509 vss switch. and i notice when the standby chassis reboot I didn't get any snmp trap, but I got when the active one reboot. my question is is there any mib out there for detecting and got a trap when standby reboot?
View 2 Replies View RelatedI am having an issue with this device after setting the ip address and rebooting. I have tried renaming the config.text file without success. I have also tried the steps mentioned here: [URL]
View 1 Replies View RelatedI was trying to configure an SF 300-24 for use in my home and obviously did something dumb. It was working fine. The f/w was updated and I had configured 2 VLANs. VLAN2 was ports 1-6+GE1 for IPTV streaming and VLAN3 was ports 7-24+GE2 and GE3 for the rest of my LAN. I was plugged into GE4 and was configuring the switch with a laptop. GE4 was the only port still on the default VLAN1. I chaged the default VLAN to VLAN3, which forced a reboot and the switch never came back up. Attached is what I see when I connect to the console port: [code]
I can't access to GUI using it's static IP or it's default IP on any port and the console never reaches the point where I can log in. The System light is flashing green but the boot sequence never progresses past what's in the screen shot. I tried to do a hard reset using the recessed button on the front panel but it does not seem to have any effect, no matter how long I hold it down.
I have Cisco 2811 secure router in my network. Seven day before it has been hanging every 3-4 hour. i have updated "c2800nm-advsecurityk9-mz.124-17.bin" IOS in the router. After that it giving some error and every 7-10 hour network has been delay in LAN as well as WAN and not pinging.
View 7 Replies View RelatedI have a Cisco SG200-08p that's acting up. After setting up 2 larger 200 series switches I pulled this out for its config. I changed the default password and assigned the new static IP address of 192.168.0.103, that's it. The settings applied and worked normally but after rebooting the switch it reverted itself back to the default ip of 192.168.1.254, it retained the new password. After this happened a few times I upgraded the firmware to the latest version, reset the device to factory settings and applied the new address again to have the same problem. It doesn't matter if I reboot the switch in the management interface or physically. Is there a problem with having a zero in the third octet (that would be lame)?
View 6 Replies View RelatedI have a brand new 2960S-48TS-L, plain vanilla with no extra module/boards etc. It boots up ok (the installed version is 12.2 (55) SE5) but then constantly cycles the following error, and doesn't accept any input whatsoever. After 5-10 minutes of cycling the error, the switch reloads and starts the process again.
PCIE0: link is NOT up.
--------------CPU's PCIe SDR Registers--------------------
PE_DLPSET = 00401000
PE_UTLSET1 = 00000000
[Code]......