clarify if the NM-1FE2W or NM-2FE2W will work in the 2610XM? These two pages seems to contradict each other:
[URL]
I've an option on some 2610XM's cheap for my lab, but I need to have 2FE ports in each. Some people have told me the NM-1FE2W and NM-2FE2W will work in the XM's and some others have said they wont!
I am attempting to add an additional ethernet port on a Cisco 2620 router using a NM-2FE2W card, however the card is not being detected. I read that this card is compatible with this model router, but I have also notice that there is a version 2 of this card. Have I ordered the wrong card or do I possibly have a defective card? My ISO version is 12.2(26) on the router.If this card is not compatible, what is the recommended card for adding an additional ethernet port on this router?
View 2 Replies View RelatedI have a couple of these routers in the lab with a very basic MPLS configuration on them. Everything works fine on the fixed interfaces but I cannot get the ldp neighborship to form between the 1FE2W interfaces on each router. Does this module support MPLS?
View 3 Replies View RelatedI have a Cisco 2610XM (256MB DRAM / 48MB FLASH) set up as a WAN router, routing from FA 1/0 to FA 0/0 FA 1/0 is a dhcp client and FA 0/0 is a dhcp pool server.Everything works fine except my router is capping out at about 8MB/s download speed.This would be fine except i have a 16Mb/s internet connectionIs this just the router hardware bottlenecking? or a configuration issue?Either way could you let me know how to solve this?
View 3 Replies View RelatedI have just purchased a used 2610XM router for use at home for preparing for the CCNA Security certification.The router came with IOS 12.2xxx.
I've been told that in order to get SDM, which is a big part of the cert test, I need to upgrade to 12.4xxx IOS.I've purused the Cisco site looking for the correct IOS, but there are multiple versions of the 12.4 IOS.
My question is this: which flavor of 12.4 IOS should I d/l?? And does SDM come incorporated WITHIN the IOS, or is that a separate d/l?
Im trying to get into Rommon, Im reading thats the BREAK button, which im assuming obviously its the pause/break button on my keyboard, im pressing it till my finger turns blue a billion times and still no rommon noodles for me.
View 3 Replies View RelatedI`m having problem with booting Cisco router 2610 and I`m having this message :
C2600 platform with 131072 Kbytes of main memory
Program load complete, entry point: 0x80008000, size 0x439138
Self decompressing the image :####################################################################################################################################################################[OK]
After that, I can't type any thing?
I've a home lab which consists of three 2610xm routers and I have configured two routers back to back with FR subinterfaces. The commands are used are;
R1
frame relay switching
int s0/0
encap FR
no sh
clock rate 64000
frame-relay intf-type dce
[code].....
Everything works great with this config and I know how to configure without lmi too. My question is more for the CCNA exam and fill the gaps in so to speak. The question is when you configure FR with static mappings and inverse arp do you need actual frame relay switches on the other side of the link or can I configure on my home labs routers. I know I am gonna try and configure this as well, but can I configure multipoint on my third router with a different physical interface. Like R1 with s0/0 to R2 s0/0 and R1 s0/1 to R3 s0/0 with subinterfaces.
I have recently split the voice vlan (10) from the data network (1), and am wondering why my catalysts and router do not require an interface Vlan10 statement. In the past I used OpenBSD boxes to do the routing, and I first needed to configure vlan 10 on the interface before I could get inter-vlan communication to work. With these Cisco devices it works, and I am wondering if it is because of VTP, for the fact that the ports maybe just pass all traffic, or is there some other explanation? Below is the setup, and firmware is up-to-date on all of the devices.
When I plug a phone into the POE SGE, the phone turns on, obtains an address on the proper subnet, and conversations are clear (whereas without the ip nat inside on the new subnet the calls had a lot of static). Possibly the reason that it works is because the phones properly create the tcp/ip packet, and it hops over the trunks and creates the states so that traffic routes back properly. I will install wireshark to see exactly what is going on, but is there a simple explanation that I am overlooking?
The N2K data sheet says that it doesn't, but I want to confirm that it isn't old information. How to have this working and what versions are you using?
View 6 Replies View Relatedscenario A
A site .
PBX --->
Data ---> other brand router ----> 3750X ---> wan
[Code]....
How to know whether QoS work on the 3750X or not ? Is it correct about the config in scenario A ?
I wonder if Cisco 1000BASE-T SFP can work with CAT-6 cable. I believe it can. But in the Cisco datasheet, it only mentions that “The 1000BASE-T SFP operates on standard Category 5 unshielded twisted pair copper cabling of up to 100m (328 ft) link length”.
View 3 Replies View RelatedRecently I'm working with my client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply) Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET,This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.Access-list 100 permit ip any any dscp default,class-map match-all QoS_Floor_Limit, match access-group 100.
View 1 Replies View Relatedwill the AIM-COMPR2-V2 will work with the 2621xm
View 1 Replies View RelatedI created the configuration below to limit the bandwidth, but doesn't work
Qos - 3750
!
mls qosmls qos map policed-dscp 10 to 8!class-map match-all Testmatch access-group name ACL!policy-map QOSdescription Limit 10M set ip dscp af11 police
[Code]....
I have switch Cisco 3560 and I would like to filter multicast traffic. Short explanation. This are multicast addresses from provider on VLAN 888 :
I expect that streams from acl Streamfrom888 will be dropped and the rest of streams will be forwarded. Unfortunately traffic from all streams passs through.how to configure VACL or where in my configuration is mistake?
I started to set up a 1721 router with WIC-4ESW. This is on an internal network, so only looking to just do routing from FA/0's interface to the networks attached to ports on the WIC. I first assigned just VLANs to 2 of the ports and this did not work. So I did some reading up and decided to use bridge groups. Except I still can not access the interfaces on the WIC. And by that I mean on the router itself I can not ping the ip assigned to the BVI.
I have another 1721 w/4 port that long ago I seem to remember simply assigning VLANs to the interfaces and I was able to communicate between the networks without issue (or maybe I just don't rememer that well). Thing is I should be able to at least ping the internal interfaces shouldn't I (assuming the status is up). I don't know why BVI2 and 3 are listed as down, nor do I seem to know how to bring these up.
This is what ip int br gives me:
1721#sh ip int br
Interface IP-Address OK? Method Status Protocol
BVI2 192.168.101.1 YES manual down down
[Code]....
I have a 2960G that I keep on the bench as a work switch. I assigned an IP address to it. The techs have had trouble imaging workstations using GHOST. Do any config changes need to be made to enable multicast to work? Everything is in VLAN1 at this point and the GHOST server is also the DHCP server.
View 1 Replies View RelatedJust I have upgraded some 2960S to IOS 15.0(2)SE from a IOS 15.0(1)SE3 and the catalyst don't switch any IPv6 traffic. Don't work any RA and also don't work any unicast IPv6 traffic from any interface. I can see some references to IPv6 changes in the FHS (First Hop Security) in the Release Notes, but no any reference to changes in the configuration.
The switches don't have any IPv6 specific configuration and the sdm is the default templata. Returning to 15.0(1)SE3 everything work ok.
On Catalyst 2960, and 3560E this IOS version seem to work fine with IPv6.
I have PC_A and PC_B connected to the same switch, and are put in the same vlan. PC_A is the master (source) and PC_B is the destination (client). IGMP Snooping is enabled by default.
Is there any reason why this should fail? There is no RP or any interface with PIM enabled. Its a flat network with a source and client in the same vlan...
IH-3750-LOADTEST-101#show ip igmp snooping vlan 724
Global IGMP Snooping configuration:
-------------------------------------------
IGMP snooping : Enabled
[Code].....
I have C3750X with C3KX-NM-10G, and have-T SFP in slot 3 ( means it is not in SFP+ slot ).I need to set speed&duplex hard to 100/Full, but if I do the link goes down. I have the same settings on the other side, only IOS version is different.I tried other speeds - 10 and 1000, but no one works with Full. When I change duplex to Auto it works fine.The reason why I am doing this on C3KX-NM-10G is because I need to use NetFlow and cannot use the chassis' copper port. At the moment the ports are connected through a copper patch cord, but in full production there will be a radio link in between that requires 100M/Full to be set hard.I am trying to search for any document that would describe this limitation, but cannot find any. Also port capabilities do not indicate duplex could not be set to full:
show interfaces g1/1/3 capabilities
GigabitEthernet1/1/3
Model: WS-C3750X-48P
Type: 10/100/1000BaseTX SFP
Speed: 10,100,1000,10000,auto
Duplex: half,full,auto
Trunk encap. type: 802.1Q,ISL
[code]....
How to configure a 4500X with a GLC-T SFP so that it will work at 100M.The data sheets say it will work at 10/100/1000 but Im not seeing that happen can't set the speed and it doesn't negotiate with anything at 100M it will only work with auto to another switch set to auto and supports 1000M.
View 6 Replies View RelatedDoes the port adaptor PA-MC-2E1/120 work with the Catalyst Switch 6506E (Sup Engine: 720-3B)? We have bought a Enhanced FlexWAN card for this port adaptor.I read through the cisco website and seem to get confusing answers whether they are compatible.
View 1 Replies View Relatedc3750e-universalk9-tar.150-1.SE on 3750x
username cisco privilege 15 secret cico
aaa new-model
aaa authentication login default local
[Code]....
Console and telnet don't seem to auto authorize to level 15, I end up at level 1, I'm forced to use enable command.
Rolling back to c3750e-universalk9-mz.122-58.SE2 fixes it. Going back to c3750e-universalk9-tar.150-1.SE breaks it again.
is there some new behavior in cat 15 code (couldn't find it in config guide)? maybe a bug (couldn't find one)?
my client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.
Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply) Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET
This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.
access-list 100 permit ip any any dscp default
class-map match-all QoS_Floor_Limit
match access-group 100
!
!
policy-map QoS_Floor_Limit
[Code]......
I cannot get the AAA tacacs+ authentication to work on my Nexus 7000.
View 4 Replies View RelatedA client asked this question. Below is how I responded:
Q: Will the NFFC for the 4500 series work with a SUP6-E/SUP6-LE?
A: NO.
I have never attempted to install one on a SUP6-E, but there is no documented capability of that SUP to do netflow, either natively or with a daughter card. I can NOT however find any explicit documentation stating it will not work – only lack of documentation stating it will.
Specifically, it will or will not work? I suspect "no" based on how difficult it is to find either component on the same page, but I simply don't know.
make a couple of SF300 switches to work properly with a C2960S-48TS-L that acts as core switch/basic router. I can't seem to figure out how to assign VLANs correctly in trunk and access mode on the SF300. The 2960S are a no brainer with IOS commands but the webgui in the SF300 is a pain.
I've configured the 2960S with 3 VLANs and I would like to have the SF300 switches connect to the C2960S-48TS-L through VLAN trunk and then configure the ports on the SF300 switches to belong to the assigned VLANs of my choosing. I would also like to have all the SF300 switches management interface in VLAN 50.
I've partially described the enviroment below.
VLANs
Data VLAN 10: 192.168.10.0
Management VLAN 50: 10.20.30.0
Voice VLAN 100: 10.10.10.0
[Code].....
I have 2 local accounts on a 3750 that kick in should radius be unavailable. If I log in as the admin account it gets priv 15, if I log in as the other user it gets privilege 3 which is correct, by my commands dont work, this is what I have added and the strange thing is I've dont this many times before on our other switches
username admin privilege 15 secret ***
username users privilege 3 secret ***
aaa new-model
[Code]....
We had power failure catalyst 6509 and after the device boot up ssh does not work any more below is error messages
line con 0
access-class 90 out
logging synchronous
[Code]....
I have came across this topic, and I am wondering if this images can be uploaded to any 2900 series switches or not, and if this will work as access port for more than vlans. URL...
View 2 Replies View RelatedWe just replaced our Cisco 1240 AP in one of our shops with a Cisco 1141 AP. This is not controller based.
We use several wireless (infrastructure mode) auto diagnostic tools which connect to the AP. We also have many laptops which run the diagnostic software.
We had no problems with our 1240AP. With our 1141, we cannot connect to the wireless tools if both the laptop and the tools are connected to the 1141. If I connect one to the 1240 and one to the 1141, they can see each other and work fine. IF they are both connected to the 1141, they show up as connected in the AP, they can ping each other, but the software does not communicate.
[URL]
I have a Cisco 2940 switch and a Cisco 1841 router. I want to build two different VLAN networks on the switch, which do not have to communicate one with each other, but those VLANS should communicate with the router.
I read a lot of articles, i tried to configure properly the switch and the router but i still don't get them work.
I set on the switch, the GigabitEthernet 0/1 port to Trunk port and i had to set it a native VLAN. The problem is that only from that native VLAN, i can ping the router.