Cisco :: Using P2P With Cisco RV042
Jan 27, 2013
I have the above router and use P2P program to download the odd TV series only thing is that when I'm using Tixati to surf on the same computer or any other computer on the network is very slow. To get around that I only use the P2P when everyone is in bed. Is there any way to limit the bandwidth that the program uses. Also not related to the above question but I have another RV042 in another location using VPN and a wireless router. Looking for all in one solutjon does not have to be a new router was thinking about SonicWall TZ 150.
View 4 Replies
ADVERTISEMENT
Jun 28, 2011
I had an older Linksys RV042 working perfectly until it blew up on me after 5 years of faithful service. This new 'Cisco' with v4.0.0.07-tm firmware appears to be a dramatic step backwards - I'm tempted to call it a heap of junk!!!
1. The 'Smart Link Backup' is not working (our primary ISP failed today and it did *not* switch over to the backup ISP on WAN2 as advertised and more critically ..
2. It *will not* allow me to access the sbs-2003 R2 server using Remote Web Workplace.
From ouside the office I can connect to the server using a Remote Desktop Connection and my laptop clients can use the built-in sbs 'VPN' connections but not RWW.
I have duplicated all the port forwarding as per the old router, turned off the firewall and even tried forwarding 'all traffice to the servers external NIC all to no avail. I get 'error 404' when clicking past the customary 'continue to this website ..." certificate warning.
I administer another 2 installations that use different routers and work flawlessly
View 1 Replies
View Related
Feb 27, 2012
I have two Internet connections-
1-DSL Modem (WAN1-Internet Port)
2-Cable Modem-Comcast (WAN2-DMZ/Internet Port)
I connected the DSL (WAN1-Internet) port in and the Cisco RV042 was able to get an IP automatically. I tested the connection and it works just fine. Then I connect the Cable Modem-Comcast (WAN2-DMZ/Internet Port) in and I have the RV042 automatically optain IP address. But it just says 0.0.0.0. I've tried release/renew and that does nothing. Also, when I connect the 2nd Internet connection the Internet goes down. The only way it goes back up is when I disable under the PORT MANAGMENT setting.
All the settings have been kept to the default.How can I get the router to obtain an IP address from the Cable Modem-Comcast (WAN2 DMZ/Internet Port).
View 5 Replies
View Related
Jan 29, 2012
I recently purchased a RV042 device but when I tried to set my DDNS account I realized that the only two providers are dyndns.org and 3322.net. We already have an account in no-ip.com and several services using the [URL] host.
How can I set up a no-ip account in my rv042?
View 6 Replies
View Related
Mar 6, 2012
We have an Cisco RV042. We need to setup a VPN with a business partner who is already using our current IP scheme on another VPN with another client. They have asked us to NAT our IP's from 192.168.25.x to 192.168.245.x
I can't seem to figure this out on this router. I have done it on a Sonicwall and Watchguard, but can't seem to get it to work on the RV042.
I have setup the VPN and the One-To-One NAT. The tunnel will connect (using the 245.x IP as our local IP on the VPN setup), but no traffic will pass through.
View 1 Replies
View Related
Nov 2, 2011
How do you setup a Clint VPN on a RV042
View 1 Replies
View Related
May 20, 2012
i was planed to make a vpn over rv042 so i get the rv042 connected behind a thosmon 456(configured as a bridge) and 1 static ip ... and i configured the vpn and worked great ...but due to some circumstance i get a package of 6 ips insted of the old ip , so when i try to configure the router with the ISP they but the wan ip 10.232.x.x and told me that an internal ip from there lan ... and give me the 6 ip of 196.x.x.x to use as 1 for internal interface for the rv042 and 5 for the pc's,now the vpn not working anymore...notice: when try to configure the vpn tunnle in the local securty setting i mark the ip only and the ip that abear is the wan ip 10.232.x.x but i can't ping that ip beside i can ping the internal ip of the router 196.x.x.50does rv042 can support static and virtual ip inside the lan |! can i configure the thomson as pppoe and use one static ip from 196.x.x.x as wan ip for it ... and use anther 196.x.x.x ip for the rv042 to get access from outside and connect the lan to the rv042 with internal ip 192.168.x.x ...so i can access the vpn from outside .....and can connect the device i need to use static ip to the thomson ...
View 0 Replies
View Related
Sep 23, 2011
Firmware v4.0.4.02 has a nasty bug in the VPN section. If you switch to "IP by DNS Resolved" (yes, it says "Resolved" instead of "Resolution". Gotta love all the Engrish in the RV042!), it will automatically populate the field with "@yourdomain.com". This will cause the VPN to not lookup the proper IP address. Simply deleting the atmark after it populates will fix the problem.
Let's see what happens when we validate a Cisco RV042 webpage:
Errors found while checking this document as HTML 4.01 Transitional!
Result: 353 Errors, 1 warning(s)
Don't even get me started on the horrible Javascript...
View 0 Replies
View Related
Apr 24, 2013
i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
Apr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, Oakley proposal is acceptableApr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, IKE SA Proposal # 1, Transform # 0 acceptable Matches global IKE entry # 6Apr 26 00:43:44 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, Freeing previously allocated memory for authorization-dn-attributesApr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, PHASE 1 COMPLETEDApr 26 00:43:45 [IKEv1]: IP =RV.RV.RV.139, Keep-alive type for this connection: DPDApr 26 00:43:45 [IKEv1 DEBUG]: Group =
[code].....
View 1 Replies
View Related
Sep 27, 2012
Apparently one of my two ISPs,CenturyLink, supports 6rd connections to IPv6.
This is supported natively on my Q1000 ActionTec modem, however my modem is in "transparent bridging" mode, so that the RV042 v3 can be the only router.
how to configure the RV042 to operate in this manner.
Per the CenturyLink FAQ: the IPv6 address space is:
2602::0 /24
Most importantly, can I do this WITHOUT buying a new modem.
View 2 Replies
View Related
Jul 5, 2012
we are trying to establish VPN tunnel between ASA5550 and RV042. The tunnel is connected but I cannot access any resources that are behind ASA5550. I can ping the servers but that is about it.
View 1 Replies
View Related
Aug 28, 2011
I have a RV042 router (Ser#: NKS10462300, HW V3) running Firmware version v4.0.2.08-tm (Jan 14 2011 22:08:38) set up as a gateway. Right after it boots I am able to long into its web interface but shortly after that if I try to log into it I go through a very log time out while the web page is waiting the router to respond and then eventually IE comes back and says it 'cannot display the web [age'.
View 30 Replies
View Related
Jan 14, 2013
I have a Cisco RV042 VPN Router and I have added a group vpn, but when I am trying to connect I got an error that the remote vpn server isn't responding.
Here's my log:
2013/01/15 12:24:53 [STATUS]OS Version: Windows 7
2013/01/15 12:24:53 [STATUS]Windows Firewall Domain Profile Settings: ON
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]One network interface detected with IP address MY HOME IP
[code]....
If I am trying to connect the status of the vpn user in the remote interface is "online".I have deactived my firewall at home and at the server for testing purposes.
View 2 Replies
View Related
Sep 1, 2011
I have a RV042 with a DSL (static IP) and a cable connection (Dynamic). How do I get the extra bandwidth from the cable and still keep the static IP of the DSL. When I have the router set on WAN1 (DSL), I get buffering. When I set the router on WAN2, I lose the static IP and therefore, the stream. When I have the router set on Load Balance, it switches the IP back and forth between the static DSL and the Dynamic cable.
View 1 Replies
View Related
Apr 19, 2012
I am looking to configure RV042 for VPN access to local machines and Win 2008 server. The story: Had issues with remote printers being created for clients logging into old Linksys RV042 with Linksys VPN software. First Tech exposed server without security, and it had to be removed as it was being attacked, but did not fix printing issue. 2nd tech could not get VPN to work after 1st tech. 3rd tech, 4hours, and I got that the router is a piece of ... So I'm out over 1000, and not able to have a simple router set up. The present situation. New RV042 with firmware V4.1.1.01, using Cisco VPN client 5.0.07.0410, most XP 32 bit machines coming into network, one 64 bit win 7. My clients have been unable to access their data for too long.
View 3 Replies
View Related
Jul 25, 2011
First of all i have gateway 2 gateway VPN configuration (both same RV042 with same firmware) + QVNP clients
The first one that i have those lines in my log "Ignoring Vendor ID payload" which doesn't allow clients to be connected from the first time they connect after several retries, or can't connect at all. I've doublechecked ports opened, and 500 is blocked by ISP. Also double checked, tried turning on and of Windows machine firewalls and etc - nothing worked. What would be the solution? should i manage to call my ISP and ask opening the port and it will solve my problem? HTTPS is enabled on router (this one i read in other topic)
The other problem is that one of my routers just stuck and i have manually to turn off, and then to turn on that it would start working as it was. Log files doesn't show anything. Router started to crash after the last Firmware upgrade.
View 1 Replies
View Related
Feb 6, 2012
Is there any documentation out there on a step-by-step instructions on setting up a vpn on a RV042 router?
View 1 Replies
View Related
May 3, 2011
I will attempt to make is simpler this time. I have a gateway to gateway VPN tunnel setup using two RV042 routers. I have been using this gateway for years without any issues. The computers on each side of the tunnel were Windows XP. I also use RealVNC Enterprise Edition on each computer for easy access to their desktops and applications. I have added two new Windows 7 Pro computers on each end of the tunnel.
The problem is with the two new Windows 7 computers. I am able to connect from a new Windows 7 computer to a Windows XP computer located on the opposite side of the tunnel fine with RealVNC. If I connect using the same Windows 7 computer to a new Windows 7 computer on the opposite end of the tunnel the connection will disconnect after a few seconds. I have disabled Symantec Endpoint Protection 11 and even upgraded it to version 11.0.6300. I also installed the most up to date driver for the Intel 82579V network adapter on the ASUS P8P67 Deluxe motherboard.
I attempted to install Cisco's Quick VPN for the RV042 with no luck on that. The certificates that the router uses do not work in the Trusted Root Certification AuthoritiesCertificates folder. So I gave up on that approach. All efforts to possibly by-pass the problem have failed. There is something with the two Windows 7 computers communicating through the tunnel that does to happen with the Windows XP computers.
View 1 Replies
View Related
Apr 30, 2012
I'm trying to set up 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24. I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 6 Replies
View Related
Feb 23, 2012
So far I have a complete phase 1, and an almost complete phase 2, but one thing I can't figure out. I see this in the debug. peer is not authenticated by xauth - drop connection.
I get it right after the proxy is setup.
Here is my config
group-policy DefaultRAGroup attributes
vpn-idle-timeout none
vpn-tunnel-protocol ikev1 l2tp-ipsec
[Code]....
I have tried many different configurations on both sides, but they all fail with the same error of peer not authenticated by xauth.
View 8 Replies
View Related
Sep 2, 2012
The issue is when I am using PPTP the router seems to die, not every time but I would say about once a week now. I am the only PPTP user, simply using RDP. A few hours into an RDP session the PPTP connection drops and cannot be re-established, or quickvpn, nothing. Routing still works (somewhat, high latency) locally.
When I've checked the logs both times I see:
TimeEvent-TypeMessageSep 3 17:07:56 2012KernelOut of memory: Killed process 14354 (pppd). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 177 and children. Sep 3 17:07:56 2012KernelOut of memory: Killed process 14367 (sh). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 234 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14330 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14329 (pptpctrl) score 134 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14324 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14324 (pppd) score 177 and children. Sep 3 16:46:40 2012KernelOut of memory: Killed process 14328 (sh). Sep 3 16:46:40 2012KernelOut of Memory: Kill process 14324 (pppd) score 234 and children. Sep 3 15:36:15 2012KernelOut of memory: Killed process 14187 (pppd). Sep 3
[code]....
View 3 Replies
View Related
Sep 5, 2011
I have few router Cisco RV042, and VPN links between them with a hub and spokes topology. Every spoke VPN works, they succeed to connect to the hub. The hub can see every spokes VPN active. A computer under the hub can connect to a computer under any spoke. A computer under any spoke can connect to a computer under the hub. That works great. Now, what I really need is to connect computers under a spoke to connect to computers under an other spoke. I was wondering if the Cisco RV042 can be configure to allow that and HOW? If it can't be done, what other router should I use as the HUB? Does I need to change the spokes as well?
View 4 Replies
View Related
Nov 11, 2012
I have an RV042 connected via VPN to the office (to a LinkSys DFL-700). Sometimes the VPN is dropped and never activates again. In this state, if I try to connect to the WEB interface, I can log in, but the router hangs at the login screen. I have to power recycle the router to make it work again.
Updated to latest firmware 4.2.1.02 for V3 hardware. The funny thing is that services from the WEB routed through to local IP adresses on the lan is still accessible. I have setup PPPT VPN on the router, and that also fails to work.
Is there, as a workaround, any possibility to access the routers reset page or access via TELNET to reset the router? This migth be useful, when I'm out. (I have a backup solution to access the local network at home).
View 3 Replies
View Related
Feb 9, 2011
I'm experiencing quite a slow vpn performance. I've tested different scenarios.
* Windows XP with built-ín pptp client and Shrew ipsec client
* Linux built-in pptp
* wireless and wired connections
I never managed to go above 1MBps neither with windows or linux. I managed to go up to 3MBps using the Shrew client.I've also checked mtu settings and everything seems to be fine.
View 8 Replies
View Related
Dec 5, 2012
Connecting the sip trunk provider modem and my network on the rv042 and connect my phone system on it so he can access both my sip trunk and internet connection.
I have 1 WAN modem from my sip trunk provider connected to the first WAN interface in the RV042.My network is connected to the second WAN interface programmed as a transparent bridge to link both lan segments together
however the link between the WAN2 interface and the network seems to go up and down and i cant ping my network gateway from a pc connected to the switchport of the RV042.
all i need is internet access to the phone system for email notification via a SMTP server.
View 1 Replies
View Related
Jun 29, 2012
I have just purchased the RV042 and while it is working great on WAN1 over Xfinity/Comcast broadband, I'm unable to get it working with my AT&T DSL for WAN2. I am planning on running this in failover mode - not load balancing.
The DSL modem it is connected to is a SpeedStream (hooking up laptop directly works etc. etc.). The SpeedStream is set to PPOE authentication passed in via the computer (in this case the RV042). On the RV042 side, I set it to use PPOE, using the credentials as given my AT&T DSL. The DNS servers are set to the ones recommended
View 4 Replies
View Related
Oct 24, 2011
I'm a bit new at this and I wanted to know if this is possible with the RV042 or if there's a better product to use. Our server is at located at location A and locations B and C telnet to the server via a VPN. We're looking at getting another ISP at each location as a backup and abandon older modem backups.
Would I setup a VPN tunnel between (A and B) and (A and C) for each ISP? Also I had a question on local IP addresses and if this would work
location A, ISP 1 -> location B, ISP1
local IP 192.168.1.1 remote IP 192.168.2.1
Public IP aa.aa.aa.aa Public IP bb.bb.bb.bb
[ code]....
View 2 Replies
View Related
Mar 22, 2012
I am a employed at a credit union with 17 branches. We have a mpls circuit connecting the branches to our main office. I setup DSL as a backup connection. I have 17 RV042 Cisco VPN Routers. I created a secure vpn tunnel for every branch to the main office. I made a delayed route in our main router to fail over to the VPN, in case the mpls failed. Almost everything works great except our ATM's are required to connect to a router at our main office to a different subnet than the tunnel is connecting, therefore not routing through the tunnel. I've tried creating another tunnel but only works with one of the branches, cause I get a conflict at the main office when I try a second tunnel with the same ip network. Also I tried routing all the traffic through the vpn by putting in the address 0.0.0.0 subnet 0.0.0.0, at the branch site. But I can only do that for one branch, The Downtown Cisco won’t let me create another tunnel with that setting.
View 1 Replies
View Related
Jul 18, 2012
Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies
View Related
Feb 6, 2012
i have setup vpn connection (client-gateway) using quick vpn ( default cisco) and third party like thegreenbow. connection is ok (established) but why from outside I can only ping to IP LAN PC , if I ping ip server the result is request time out(failed). I have been trying do this to 3 server ( windows server 2003 as OS).four your information I have made firewall "OFF" on all of those servers. the result is same, failed.
View 0 Replies
View Related
Sep 28, 2012
I'm tryig to put a computer into the DMZ and then access it from computers on the LAN using a local IP address. My reason for doing this is that I'd like my DMZ computer to be a locked down web server (just ports 80 and 443 open to the outside), but I need to be able to have more access to it from inside my LAN (e.g. I want to be able to SSH into it from the LAN).
Thus far I've been able to get a computer set up in the DMZ and can access the Internet from the DMZ computer. And I can access the DMZ computer from the LAN computers using the public address for the DMZ computer. But I can't access the DMZ computer from the LAN computers using a private address for the DMZ computer. see the attached file for a diagram of our current settings. A few descriptions:
- Verizon provides us with a number of static IP addresses, i.e. 71.123.123.10-12 (note these aren't actually the addresses, but representative).
-- In the RV042, I have the following configurations made:
- Setup > Network > LAN Setting
- Device IP Address = 10.4.20.1
[Code]......
View 7 Replies
View Related
Dec 21, 2011
I have a static DSL connection and my ISP is giving me 4 static IP's. I have connected my RV042 to the DSL modem and I have now 1 subnet at 192.168.0.0. What I want to create is a WEB server/ Email server, but to sit on a different subnet - 192.168.5.0. For now I have connected the server to the DMZ port, but I am unable to to access it from WAN, only from LAN. How to configure properly the 2 subnets (192.168.0.0 and 192.168.5.0) and how to forward my static address to the server which I which to be on the 192.168.5.0.
View 4 Replies
View Related
Dec 18, 2012
i'm trying to set up a simple VPN (client to Gateway), but i can't ! An SSL VPN or an IPSEC VPN, whatever..
The firmware of the RV042 is up to date, and i'm trying QuickVPN as a client vpn (also updated...)
My configuration details :
I'm in : 192.168.2.14 /24
My RV042 : 192.168.2.250 /24
And the VPN intend to connect me to : 192.168.4.x
[Code].....
View 5 Replies
View Related
Jan 10, 2012
We are currently installing RV-042 V3 Dual WAN VPN Routers for a Customer with an HQ Office & 3 Branch Offices. The Customer recently requested to use the WEB Filter feature available in the RV-042 V3 Router to do the followng : - " Block all the HTTP Traffic Except for the company Website " We tried all the Combinations between " Access Rules " & " Content Filtering " available under the " Firewall " but we always reach the result that either to Allow ALL HTTP Tarffic to All Websites or to Block ALL HTTP Traffic.
how to Block all HTTP Traffic except for certain URL ( Using the URL Name NOT the IP Address ).
View 3 Replies
View Related
