Cisco VPN :: 1941 Not Working With Tata Photon

Jul 14, 2011

I have a VPN setup in my network. Whenever I try to connect to VPN using Tata Photon, VPN successfully gets established, but I can not access/ping any devices in network. If I connect VPN using any other internet source (Broad band, internet lease line) VPN works properly. I have cofigured split tunneling on 1941 series routers.
 
One thing I have observes is that, after connecting photon, default route injected in PC has metric of 41 and after connecting VPN, specific route for network has metric of 100. Could this be a issue? can PC prefer exact route over default route?

View 1 Replies


ADVERTISEMENT

TP-Link 3G/3.75G Router :: Unable To Connect MR3220 To Tata Photon Plus

Apr 8, 2013

Region : India
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP : tata photon plus

I have Tp-link 3g/3.75 wireless lite n Router model number TL-Mr3220 . I have just bought Tata Photon plus device huawei ec156. I am not able to connetct to the usb dongle . How to connect to the USB dongle. Following the ast setup guide . Its saying Unknown PIN status, please insure that your SIM/UIM is on unlock status.

[code]...

View 1 Replies View Related

Connect Tata Photon Modem To Bsnl Wifi Modem Via Usb Port?

Jan 16, 2013

I want to connect my tata photon device to my bsnl wifi modem via a usb portavailable on the bsnl modem. This is to provide a wifi network that i can use to surf the net on my phone.

View 4 Replies View Related

Cisco WAN :: NAT IP Is Not Working In MWR 1941 DC?

Feb 18, 2011

I got 2 DC Cisco MWR 1941 and 3600, I do not know the reason why when I set up IP NAT to 1941 does not work but if I do it in the 3600 if it works.

View 13 Replies View Related

How To Connect Two Computers With Same Photon Plus

Mar 6, 2012

i need to know is there any way to connect two computers to the same data connector like photon+ or other net connectors

View 1 Replies View Related

Cisco WAN :: 1941 W Wireless Not Working

Mar 20, 2011

I have been breaking my head over a problem with my new 1941W ISR since about two weeks now.When I restart the router, the service-module wlan-ap0 is not working.After a restart of the router, when I ask a service-module wlan-ap2 status, I get:Service Module is Cisco wlan-ap0Service Module supports session via TTY line 67Service Module is waiting for registration messageService Module reset on error is disabledService Module heartbeat-reset is enabledService Module is in fail openService Module status is not available
 
After a while it changes to Service Module is failed.If I restart the module with service-module wlan-ap2 reset, it works. Is this a technical error?

View 4 Replies View Related

Cisco WAN :: 1941 Router - CP Express Not Working After Upgrade

Aug 13, 2011

I am trying to upgrade CP Express to 2.5 and after the upgrade I bring up the webpage to login and I am prompted for my credentials, I enter them and I am authenticated.  However the CP Express home page never loads. I have tried to reload 2.0 but it does the same thing.

View 3 Replies View Related

Cisco Switching/Routing :: 1941 - SSH Not Working From Internet

Feb 12, 2012

I have a Cisco 1941 router configured using Cisco Configuration Professional... SSH management works from the LAN IP 10.0.1.254 and 10.0.2.254 Also, SSH management works from the LAN using the external domain name which resolves to the public IP address.
 
The problem i have is if I try SSH from the internet to the public IP.. nothing happens. 

cisco1941#show config
Using 18498 out of 262136 bytes
!
! Last configuration change at 13:57:49 PCTime Tue Feb 14 2012 by admin

[Code].....

View 2 Replies View Related

Cisco VPN :: How To NAT After Connecting 1941

Feb 22, 2012

I have a Cisco 1941 which has several Cisco VPN clients connecting to it which all works fine. The details of the LAN and VPN clients are as below:
 
Cisco 1941 LAN : 172.16.1.0 255.255.255.0
VPN Clients : 192.168.5.0 255.255.255.0
 
As mentioned this works fine but I'm about to setup a point to point VPN with from the above Cisco to another site which isn't controlled by myself and the remote side of this point to point VPN will only allow connections from the "172.16.1.0" subnet to communicate with it.
 
The issue I have is that the Cisco VPN clients also need to communicate with the remote side of this point to point VPN but they are obviously coming from the "192.168.5.0" subnet. Is this possible and where to start with this that would be fantastic.

View 3 Replies View Related

Cisco :: 1941 / IP SLA In Combination With DMVPN?

Sep 5, 2012

I have a problem with my routers (cisco 1941)I'm running a DMVPN network (Hub and spoke)All the hubs are connected to the 2 hubs. With 4 tunnels. (each hub has 2 interfaces to the spokes. the spokes only have one interface to the hubs, so I splitted them and so I now have 4 dmvpn tunnels). one of the interfaces on a hub malfuntioned and because of that the customers had problems with logging in and sending packets. I made this kind of structure because of when one of the tunnels failed the spoke could use the 3 others... BUT, what happened here was that the spoke still tried to use all 4 of the tunnels and because of that I had 25% package loss!So this didn't work. Now I read about IP SLA, but I was wondering of this could work? (I cannot test it on spare routers, and I don't want to implement it and risking a total network failure...) and how to configure it. Should I make 4 different sla processes which I should all 4 track? And when I make the ip routes, how should I make or configure it so that 1 of the tunnels/interfaces fails that the spoke would addapt the routes?

View 1 Replies View Related

Cisco WAN :: 1941 - Routing Between 3G Interfaces?

Apr 11, 2012

I'm trying to get two Cisco 1941 routers with HWIC-1T and HWIC-3G-HSPA interfaces to use the 3G interfaces if the frame is down (as it is right now).In the lab, I was not able to get these to use the 3G interfaces as a backup (i.e. backup interface cell 0/1/0) and I've not been able to workout the correct incantation for static routing either.
 
kununurra#show ip int br d1
Interface                  IP-Address      OK? Method Status                Protocol
Dialer1                    172.31.2.94     YES IPCP   up                    up

[Code]....

View 4 Replies View Related

Cisco VPN :: PAK To Activate VPN On 1941 K9 Router

Jul 1, 2012

We bought a CISCO1941 K9 router. To enabled IPSec feature, I need the PAK to active IPSec on 1941. Where I can buy a valid PAK? Could it be done via on-line support?

View 5 Replies View Related

Cisco VPN :: Activating SSL On 1941 Router?

Mar 23, 2011

I have got a Cisco 1941 router and would like to activate my SSL VPN license on it. How do i go about it?

View 6 Replies View Related

Cisco WAN :: What Is The Processor Available In 1941 Router

Jan 31, 2012

What is the processor available in cisco 1941 router? is it RISC?

View 4 Replies View Related

Cisco VPN :: How To Configure SSL VPN On 1941 Router

Mar 22, 2011

How do i configure SSL VPN on a Cisco 1941 router? I would very much want a howto guide that does step by step. I have not found one my self so far.

View 1 Replies View Related

Cisco WAN :: Incoming NAT To VLAN On 1941?

Jan 26, 2012

On our Cisco 1941, we have 2 gigabit ethernet ports and a 4 port fast ethernet switch EHWIC card configured as follows:
 
GigabitEthernet0/0 131.x.x.81 255.255.255.248 - internal
GigabitEthernet0/1 131.y.y.234 255.255.255.252 - WAN
Vlan2 192.168.0.249 255.255.255.0 - LAN2, NAT inside

[Code]....

I have tested using some UDP packet sending/receiving software (which works through another router), and the packets just aren't getting through. Likewise trying to telnet into the external IP on port 80 doesn't get through to the destination server.
 
It feels like the route doesn't exist between the Vlan 100 and Vlan 2 when it's coming in, or maybe there's an ACL needed for the incoming traffic? 

View 4 Replies View Related

Cisco WAN :: Adding 3rd T1 To 1941 For More Bandwidth

Aug 15, 2012

We have a Cisco 1941 Router with two single HWIC cards supporting two T1 lines 3Mbps total bandwidth. We have a distance learning lab that takes atleast 2mb connection when in use so it realy kills our bandwidth. I was looking to possible add a thrid T1.
 
My question: Can I just buy a double wide HWIC card and replace the single port one. Would this require re-configuration or it's simply plug n play?
 
What other options can I try for more bandwidth instead of adding thrid T1.

View 4 Replies View Related

Cisco WAN :: How To Configure Loopback On 1941

Jan 28, 2013

I've got some 1941 ciscos set on every branch.We have native L2 between this offices and I want to use external ip addresses on gig 0� interfaces anfdf local ip addresses on lo 0 interfaces, and use lo 0 for vpn connections.
 
I do:
 
int gig 0/0
ip add 192.168.181.14 255.255.255.0
ip nat outside
  
I can ping it from local network behind giga 0/1 but i can't ping it fro outside, how can i do this?

View 2 Replies View Related

Cisco WAN :: PPPoE Configuration On 1941?

Mar 19, 2012

I have recently gotten a cisco 1941 router running version 15.1(3)T, and am trying to configure the router as a PPPoE server for access via a vlan on one of the gigabit ethernet ports.I currently have a cisco 2620 router (version 11.3(2)XA4) with the following relevant configurations:
 
vpdn enable
vpdn multihop
vpdn domain-delimiter @ suffix
!
vpdn-group pppoe

[code]....
 
I am trying to duplicate this (all but IP addresses) on the new router, but there are some options that do not seem to exist in this particular software/hardware combination.  Specifically,
 
vpdn-group pppoe
accept-dialin
  protocol pppoe
 
does not accept "pppoe" as a protocol, only allowing l2tp. What has changed, and what the proper configuration is.

View 1 Replies View Related

Cisco WAN :: Cannot Log Into 1941 Router To Setup

Mar 28, 2011

We purchased this router with the cisco IOS software installed.  I've installed the Vista driver on my win 7 box.  I believe that should work. I installed Putty to termainl in and I'm using a USB connection. I cannot even log into the router. I thought I was going to see some kind of setup wizard using the CISCO software so I would use a GUI and get things moving. I've got loads of reference material with command etc. but I just can't connect to the router to make it happen.

View 3 Replies View Related

Cisco WAN :: 1941 With IP Base License

Aug 7, 2012

I currently purchased, Cisco 1941/K9 with 2 onboard GE, 2 EHWIC slots, 1 ISM slot, 256MB CF default, 512MB DRAM default, IP Base.
 
Questions
 
1. With IP Base License, will I be able to run Frame Relay? I really need reference on what works and what doesn't between these different technology package licenses ? Actually frame relay is running on it right now, hope it doesn't suddenly stop after 60 days...
 
2. As I understand in order to run MPLS, I will need to upgrade to Data License "SL-19-DATA-K9".   Since, I already have a Cisco 1941 to upgrade it, I need to order a spare license / paper PAK?
 
3. Does the IP Base License support site to site IPSEC VPN or do I need to purchase a security license "SL-19-SEC-K9"
 
4. Can I have both security and data license activated on the same device ?
 
5. If I do activate security or data license will I be able to use the IP Base features at the same time?
 
6. If I purchase a new Cisco 1941 with Data or Security License do I need to purchase the IP Base License then upgrade the license?
 
7. Is the 1941 suited for voice application routing ?

View 4 Replies View Related

Cisco VPN :: 1941 / XTM22 - Traffic Only Going 1 Way

Jul 31, 2011

I have a site to site vpn between a Cisco 1941 Router and a Watch guard XTM22 Router. The tunnel is up, and from the side with the Watch guard Router, I have full access to the LAN on the Cisco 1941 side.
 
However, I cannot access any of the devices on the LAN on the Watch guard side. If you had to guess, which router would you say is causing the problem? I really don't know where to start looking.

View 7 Replies View Related

Cisco WAN :: Default Line 2 In 1941?

Mar 11, 2012

I was wondering about the folling witch i found in a Cisco 1941 running config

View 2 Replies View Related

Cisco WAN :: Is 1941 Supportable For BGP Protocol

Dec 28, 2011

My ISP is going to provide internet with dual path , for auto changover he (isp it admin) is planing for bgp implimentation.
 
is 1941 is supportable for bgp protocol ? Is it possible to create bandwitdh rate limit based on ip address on access list (be cause we are getting some 10 Ip address from isp  , out of 10 ip address , 3 ip addres has to go 3 diffrent departments) , i want restrict theese 3 ip address with 1 mb traffic as 1:1.

View 1 Replies View Related

Cisco WAN :: 1941 - Ethernet Bundling

Apr 19, 2011

We would like to describe our scenario as follows. We hosted our internet gateway at a service provider which is away from our site about 10 km distance.  The total internet b/w is 8Mbps.  To connect the internet service provider, we have two lastmile connectivity with two different service providers each 4mb as a last mile.  Both put together it will be 8Mbps.  The lastmile by the service providers are through ethernet.

Our main objective is to utilise both last mile connectivity by bundling or through any other optimum method. There are common perception that the ethernets cannot be bundled. The router model we use is 1941

View 4 Replies View Related

Cisco WAN :: 1941 - TZO DDNS Configuration

Feb 1, 2012

I am trying to configure TZO DDNS on my 1941.  The DDNS lines in the configuration file were provided one year ago by TZO support for a 1811W router, which was working befor i migrated to the 1941.  I have attached a config file and a debug file.   The unusual part of the debug file is session id 0x95.  I thnk this is the format the router would use if it had been configured using CCP.  I had tried CCP initially but it didnt work, so I deleted it from the configuration and used CLI instead.  Session ID 0x96 is the call the router is making using the CLI configuration, as seen  in the attached config file.
 
I am not sure where the problem is here.  it appears to be logging on to TZO.  It also appears that the router name is being added to the logon ID in session 0x95...ie instead of myname.net  the router is sending cisco1941.myname.net ---not sure if this is relevant or not.  It also appears that the update happens?  At least that'w what I can garner from the log file.

View 1 Replies View Related

Cisco WAN :: Extended ACL Not Work On 1941

Jun 2, 2012

I apply extended ACL on my router cisco 1941, but it didn't work. So I tried to apply standard ACL, it's work. I'm not sure about my cisco 1941 IOS is support extended ACL. My cisco IOS is
Cisco CISCO1941/K9

c1900-universalk9-mz.SPA.151-4.M1.bin
-----------------------------------------------------------------
Technology    Technology-package           Technology-package
Current       Type           Next reboot
------------------------------------------------------------------
ipbase        ipbasek9      Permanent      ipbasek9
security      None          None           None
data          None          None           None

[code].....

Is it IOS bug or limit feature on hardware.

View 20 Replies View Related

Cisco WAN :: Adding IPSec To 1941 Router?

Jan 17, 2013

I need to unlock IPSec to my 1941 router but I'm not sure which license(s) to purchase.

View 1 Replies View Related

Cisco :: Stop Downloading From Internet On 1941 / K9

May 24, 2012

Suggest some commands to stop downloding from internet on CISCO1941/K9.

View 0 Replies View Related

Cisco WAN :: Connectivity Between 1941 Gigabit Ports?

Jul 30, 2010

The problem I have run into is that I am not getting any connectivity between my two gigabit ports on the 1941. I have  ge0/0 setup as my internal network and is running dhcp, ge0/1 is the connection to the modem. I can't figure out how to configure the connections so my internal traffic on ge0/0 routes out through ge0/1.
 
Here is my config:
Using 4312 out of 262136 bytes
!

[Code].....

View 8 Replies View Related

Cisco Switching/Routing :: DHCP For PC At G0/1 From G0/0 For 1941

Mar 12, 2013

I have this Cisco 1941 router with two Ethernet ports g0/0 and g0/1. The g0/0 is connected to office LAN with internet access. As my office LAN is DHCP, it will assigned a IP address for g0/0 since this g0/0 is configured as "ip address dhcp". Now my question is that i have a group of 5 pcs, namely PC1, PC2, PC3, PC4 and PC5 that is connected to the switch and one of the ports of this switch is connected to g0/1 of Cisco 1941. Is it possible that let say PC2 and PC3 (both DHCP enabled) could access the internet access from g0/0 and at the same time, the office LAN assigned IP address for PC2 and PC3 automatically?
 
                                                       Office Lan with internet access (DHCP) (Default gateway 10.0.0.1)                                      
                                                                                          |
                                                                                          |
                                                        g0/0 (DHCP enable) (DHCP assigned IP address 10.0.0.138)
                                                                                 Cisco router 1941
                                                                                       g0/1
                                                                                           |
                                                                                           |
                                                                                  HP Switch
                                                                                           |
                                                                          PC1 PC2 PC3 PC4 PC5
                                      
Is this operation possible? if possible, how to configure inside the router 1941 to achieve this objective?

View 8 Replies View Related

Cisco WAN :: 1941 Getting Continuously BGP Notification Error

Sep 12, 2012

I getting continuously BGP notification error.We are using the cisco 1941 router. i have attached error and configuration.

View 1 Replies View Related

Cisco Wireless :: 1941 / Installing AP In Office?

Feb 4, 2013

We have cisco 1941 as router in office, it's dhcp server, it has only vlan 1 192.168.4.0/24?I've set up 1142 ap for wireless clients How can i make it give clients ips from dhcp server from vlan 1 ?

View 11 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved