We recently installed a 2911 sec router.On this device there are three Ipsec GRE Tunnnels which are working fine and an Easy VPN Server.The problem is that when clients connect to the easy vpn server they cannot ping anything inside , the configuration regarding protected networks is fine.After restarting the router the first client conneced works but when disconnected all the others are authenticating and the cant see anythining in the internal network . By checking the routing table i realized that the route to the virtual access interface is missing for no reason. i used the #debug ip routing detail command and i got the following during the client connection
Mar 31 09:51:37.875: RT: interface Virtual-Access5 removed from routing tableMar 31 09:51:37.875: RT: delete route to 192.168.20.9 via 79.xxx.xxx.xxx, Virtual-Access5
I have a 857 (124-4.T12). And would like to setup an Easy VPN server. I can run through the wizard in CCP, but it does not work from the VPN client. It does not complete the first stage of comm. All I have done is run the wizard and create a user. I'm fairly happy with Cisco routers, but the VPN part is new to me. I've read the walk through document on the Cisco site. I created it on a new local loop back.
The first time I run the wizard and click test it tells me none of the cyrpto interfaces are up. Are there some prerequisite I'm missing?
Previously, I was able to configure our Easy VPN Server with local authentication.But now, I am trying to use LDAP authentication to match with our policies.
My router is a Cisco1941/K9.
Current configuration : 5128 bytes!! Last configuration change at 13:25:16 UTC Tue Aug 28 2012 by admin! NVRAM config last updated at 05:03:14 UTC Mon Aug 27 2012 by admin! NVRAM config last updated at 05:03:14 UTC Mon Aug 27 2012 by adminversion 15.2service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot-end-marker!!!aaa new-model!!aaa group server ldap ASIA-LDAPserver server1.domain.net!aaa authentication login ciscocp_vpn_xauth_ml_1 localaaa authentication login ASIA-LDAP-AUTHE group ldap group ASIA-LDAPaaa authorization network VPN_Cisco localaaa authorization network ASIA-LDAP-AUTHO group ldap group ASIA-LDAP!!!!!aaa session-id common!!no ipv6 cef!!!!!ip domain name domain.netip cef!multilink bundle-name authenticated!crypto pki token default removal timeout 0!crypto pki trustpoint
I'm am wanting to know how to configure Easy VPN server with downloadable ACLs on a cisco router 2811.
Indeed, I would like to set up a remote access vpn that uses radius for authentication of VPN clients. The radius server is connected to an Active Directory server that contains the log in / password. I would like to on the basis of the user who connects to the VPN, the ACL that define the services or servers to which this user can access is automatically applied on the router and define the rights of the users.
I used the Cisco Configuration Professional to add an Easy VPN Server to my 3825. I'm able to connect when remote but I can't ping the default gateway of 192.168.1.1 which is in the same network as the VPN DHCP pool. I can access every single other device on the VLAN segments but not the default gateway which means when i connect I can't look at my router. And there's more, I cannot ping anything offnet (ie 75.75.75.75).
Attached are some images which show some details from the client during the VPN connect and a few from the router (i had to use the lan switch as a jump host). If you can figure this out before I go back to the coffee shop to test this tomorrow I will send you a cake.
I have a new ASA5505 which I want to use for Remote Easy VPN. The device connects to the remote ends but I am not able to ping the remote network. The interface is new to me and I am not sure where to add the routes. The local network is 192.168.66.0/24. The remote network is 192.168.4.0/24
I am trying to connect the Remote (conf) to the Corporate (conf). I have done this many times but now the new ADSM interface is confusing. I added the commands as you indicated with no success. The ASA gave me an error when I had added nat (inside) 0 access-list nonat. I wouldn't allow me to enable the EasyVPN option while this command was on the configuration. Here are the cry isa and cry ipsec isa files as requested.
In my client office, We have replaced small business router cisco RV042 with Cisco ISR router 2911, in that router we have configured NAT to allow internal user to access internet and port forwarding for outside user to access web servers and other application that are hosted internally.
we are not able to access [URL] (name changed) from internally and one of the application that are runnning on port no. 8280., and same is working properly from outside the network.other application that running on 8287 is accessible form internally.
We are accessing with ip address http://192.168.1.51:8280. and [URL] not working from inside.
i have windows 2008 R2 as CA server. and i also have 2911 router as remote vpn server. Everything works fine for desktops computers and leptops. Users automatically enroll certificates on Microsoft CA server and get connected to vpn. But problem is with ipads. When i try to connect from ipad error massage deslpays "Could not validate the server certificate" and i also get chis error massage from router "CRYPTO-4-IKMP_BAD_MESSAGE: IKE message from x.x.x.x failed its sanity check or is malformed"
With ipads built in vpn client i can see the installed certificate and use it but with anyconnect client no certificates are displayed.
I have couple of issues with my EasyVPN server and Cisco VPN Client on Win7.
1: VPN Client establishes the connection, traffic flow, destination network can be pinged. After a few minutes traffic stops passing the VPN. No ping to IP or DNS names can be made. In order to resole it. Users have to re-establish the VPN again. Occastioanl it stays and continue to work.
2: VPN Clients don't pick the same IP address from local address pool even though I specified "RECYLE" option in the IP local pool command.
Configuration:
############################################################################## TQI-WN-RT2911#sh run Building configuration... Current configuration : 7420 bytes ! ! Last configuration change at 14:49:13 UTC Fri Oct 12 2012 by admin ! NVRAM config last updated at 14:49:14 UTC Fri Oct 12 2012 by admin
I am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
I have a Cisco 2911 router configured with a couple of VPN tunnels . The issue that I am having is that I cannot access the servers (WEB,EMIL) thru the tunnel . After looking around found out that adding a route-map to my static NAT rule will fix the issue . Once I do that I am able to access the serves thru the VPN but my local machines lose internet access .So I have to delete the access list The issue seems to be with the Access list 110 permit ip [code]
I am having one router CISCO2911/K9 (Cisco 2911 w/3 GE,4 EHWIC,2 DSP,1 SM,256MB CF,512MB DRAM,IPB). But now my management asking me to upgrade this router as CISCO2911-SEC/K9.
We a remote user set up with a Cisco 877W that connects into a ASA5510 using EasyVPN (remote user has dynamic external IP)
The home setup also has a physical Cisco VOIP phone that connects into a Call Manager Express system over the VPN. The home user cannot hear the other end properly and voice is breaking up when using office apps on the VPN link at the same time (Outlook etc),
We continue to hear his voice OK when he is having these problems hearing us, so I guess the upload of voice from the 877 is fine and not struggling with congestion, so I have not put Qos Policies on the 877 as I guess it can only control what it is sending out and this is already working OK. Therefore its the 877 downloading from the ASA that seems to be the issue, voice is not getting prioritised when other traffic is getting sent down the same vpn link.
I have set up the following QoS policy on the ASA for this link so Voice traffic is prioritized, but the issue still occurs so I guess it doesn't work,
class-map HomeUser match dscp ef match tunnel-group ezvpngroup policy-map VPNQOS class HomeUser priority service-policy VPNQOS interface OUTSIDE
i have problem with a router 2900 with a card switch 16 ports (sm-es2-16p) that does not doing the intervlan routing. i have attached 2 show tech one of the router and one of the card switch 16 ports (sm-es2-16p). I connected physically the switch card to a router interface and it seem to be working because i can do a ping from my pc ( in user vlan 26) to my gateway on the router (172.20.26.1) but i can not do ping to the others vlan like (172.10.26.1) or others. .. i want to know what is happening and if it there is a way to do the trunk conectivity between the switch card and the router internally without a phyisical connection.
I have setup a basic PBR config to route Http and Https out of a different interface (fa0/0/0) but for some reason http traffic is still going out of the Gi0/1 interface.
Config attached minus the crypto stuff and the publics have been changed.
after installation of demo versions of 2900-SEC-TEMP & 2911-2921-SSLVPN-TEMP & rebooting the 2911 router I do not have access SSL commands.Show license indicates that 2900-SEC-TEMP & 2911-2921-SSL-TEMP licenses are active but NOT IN USE.
I have configured an easy vpn server in cisco 1905 ISR using ccp.The router was already configured with zone based firewall. But when i try to connect my office using vpn client i can reach only upto the internal interface of the router but can't access the LAN of my company.Do i need to change any configuration in ZBF since it is configured as 'deny any' from outside to inside ? If then what all protocols do i need to match ? Also is there any NAT exemption for the VPN clients?
For reference please see my full configuration:
Router#sh run Building configuration... Current configuration : 8150 bytes ! ! Last configuration change at 05:40:32 UTC Wed Jul 4 2012 by
I have a 2911 router. One interface is configured external (WAN) and two interfaces are configured on separate internal private subnets. What is the configuration to allow all traffic in both directions between the two internal subnets?
I have a Cisco 2911 that I am configuring for a remote site. I have configured a IPSec Tunnel from our main site ( ASA 5510 ). The Tunnel is up and I can connect from the main site LAN to the address of the 2911 through the IPSec Tunnel. The 2911 is equipped with a 16port switch service module. The switch is configured with an address and I can open a telnet session to the switch. From that session, I am able to reach hosts on the LAN across the IPSec tunnel. However, when I open a telnet session to the 2911 router, I cannot reach hosts on the main site LAN from that address. When I do, the traffic is sent outside of the tunnel instead of inside it. It works from the service module as traffic between the interfaces have the ACL for insteresting traffic applied, but traffic generated from the address of the 2911 router does not seem to get picked up by the ACL on the IPSec tunnel and it is getting the default route applied and going directly to the outside interface instead of to the tunnel. how to make this work?
I have installed a cisco 2911 router and the cisco usb console drivers on my pc, win 7 64 bit.however when I use putty and open the com port assigned it just goes blank, I am using the usb port on my laptop to connect and using the cisco usb console cable provided
I've got two routers, Cisco 2911's with 15.1(4)M1 on one and 15.0(1)M5 on another.
I'm trying to set up ip sla for vrrp tracking but the commands seem gimped? I don't even have an option for ip sla <operation number>. All I've got is ip sla responder/server/key-chain.
we are in the planning phase for a network upgrade. We have two C2960 Switches connected via one (L2) Etherchannel (4x1 Gbit/s) which works very well. In the next phase we would like to upgrade our router to an 2911 series which has 3 gb interfaces. and indeed we would like to create an etherchannel as well. our plan is to use 2 of the 2911 to connect to the first 2960 switch and the one left to the other 2960. i think we will achieve some redundancy with this config.
connected DSL directly to 2900 series router , but as DSL public IP is not static (dynamic) its difficult to access Router when out of home, any other means to access router without static IP
I have 2 2911 routers that will be connected via fiber with an ethernet Gig handoff to each router. Each router will then be connected to local networks on a second ethernet interface on the router. I have always connected routers via serial connections so this is new to me. Outside of the usual ethernet interface addressing configuration, is there anything else that would need to be configured on the 2 routers?
I'm setting up a small office network and the best way to do it,I have three pcs , I want to use one as the main data base/ server with all the main data to be stored on, I'm also installing a small data base software called lotus for everyone to access to update when needed, I'm just wondering what would be the best way to link all three pc's together as a network , this is something I've not done before, i have plenty of expirence with computers but I've never set up a network.
I have set up two ASA 5505's (lets call them ASA1 and ASA2) with site to site VPN configuration and i've encountered two problems with my setup.ASA1 has IP 192.168.1.254 on the inside interface and is connects ASA2. It's also an Easy VPN Server for external users to connect through Easy VPN Client.ASA2 has IP 192.168.11.1 on the inside interface and connects to ASA1 Problem #1 None of the ASA's can ping eachothers inside LAN IP address. Computers behind the ASA's are unable to ping the remote ASA's inside IP address. My guess is that this has to do with either NAT or built in security.Problem #2. The Easy VPN clients which connects to ASA1 are unable to access the LAN behind ASA2.
I'm looking to use 861s at few remote sites connecting to a 881 in the main office using Easy VPN. If I was to get 2 ISPs at the main office, can I configure it in a way that if the primary WAN failsover to the secondary, the VPN tunnels from remote sites will also failover?
Would you recommend an ASA 5505 at main office over the 811?
is there a easy to install SSL certificate on ASA, rather than enroll with a public CA? ASDM has a place to import certificates. Can I just upload a SSL certificate I got from my CA to ASA, withou setup CA enrollment? And if yes, how can I generate a SSL certificate request from my ASA 8.2?
Just setup a Cisco 2821 acting as the easy vpn server. All good, however, the easy vpn client, say for example doing a speedtest, is REALLY slow.
For example, both the client and server have 100M / 5M connections and doing some local speed tests thru the isp, on the client side we are seeing 4M/2M? We have very few vpn clients right now, so I can't see the Cisco 2821 being overloaded.
I have tried messing with the mtu, adjust-mss settings on the wan port on the 2821, but, no real changes?
